Role of Microstructure and Spectrum Features on the Catalysis Effect of Ce_(1-x)(Nd_(0.5)Eu_(0.5))_xO_(2-δ) Solid Solutions

Nanosized Ce_(1-x)(Nd_(0.5)Eu_(0.5))xO_(2-δ) solid solutions(x = 0.00~0.20) were synthesized by means of hydrothermal method.Then the solid solutions were ball milled with Mg_2Ni and Ni powders for 20 h to get the Mg_2Ni–Ni–5 mol% Ce_(1-x)(Nd_(0.5)Eu_(0.5))xO_(2-δ) composites.The structures and spectrum characteristics of the Ce_(1-x)(Nd_(0.5)Eu_(0.5))xO_(2-δ) solid solutions catalysts were analyzed systemically.XRD results showed that the doped samples exhibited single phase of CeO_2 fluorite structure.The cell parameters and cell volumes were increased with increasing the doped content.Raman spectrum revealed that the peak position of F_(2g) mode shift to higher wavenumbers and the peak corresponding to oxygen vacancies were observed distinctly for the doped samples.UV-Vis technique indicated that the absorption peaks of Eu~(3+) and Nd~(3+) ions appeared; the bandgap energy was decreased linearly.The electrochemical and kinetic properties of the Mg_2Ni–Ni–5 mol% Ce_(1-x)(Nd_(0.5)Eu_(0.5))xO_(2-δ) composites were measured.The maximum discharge capacity was increased from 722.3 mA h/g for x = 0.00 to 819.7 mA h/g for x = 0.16,and the cycle stability S_(20) increased from 25.0%(x = 0.00) to 42.2%(x = 0.20).The kinetic measurement proved that the catalytic activity of composite surfaces and the hydrogen diffusion rate were improved for the composites with doped catalysts,especially for the composites with x = 0.16 and x = 0.20.The catalysis mechanism was analyzed from the point of microstructure and spectrum features of the Ce_(1-x)(Nd_(0.5)Eu_(0.5))xO_(2-δ) solid solutions.     

LED用Sr(1-1.5x)Mo0.8Si0.2O3.8:Eu3+x红色荧光粉的制备及其荧光性能

通过高温固相法合成了LED用红色荧光粉Sr(1-1.5x)Mo0.8Si0.2O3.8∶Eu3+x（x=0.1,0.2,0.3,0.4,0.5）。 通过XRD、激发光谱和发射光谱测试了材料的物相组成以及发光性能。 x=0.1样品的XRD谱与JCPDS 08-0482(SrMoO4)的标准卡片相同。 Eu3+代替晶格中Sr2+的位置成为发光中心。 随着Eu3+含量x的增加,593 nm处的5D0-7F1跃迁和614 nm处的5D0-7F2跃迁发射强度会相互转换：当x≤0.4时,以磁偶极5D0-7F1跃迁为主,发射橙色光;而当x=0.5时,以电偶极5D0-7F2跃迁发射为主,发射红光。 可能是过量掺杂的Eu3+离子,只能存在于晶格空位形成缺陷,无法占据SrMoO4中Sr2+的格位中,Eu3+在晶格中占据非对称中心的格位,导致电偶极跃迁变成允许跃迁,从而增加了5D0-7F2跃迁,减弱了5D0-7F1跃迁。 因此,可以通过调节激活剂的含量获得不同发光色的荧光粉。 Eu3+掺杂的硅钼酸锶体系,614 nm激发下,在368 nm处出现宽的基质吸收峰和467 nm处7F0-5D2的跃迁峰,且这2处的吸收峰在x=0.5时比x=0.4时强3倍左右。 材料能非常好的吸收368 nm波长的光,产生颜色可调的橙红色。 与近紫外光LED芯片匹配良好。     

Y2O3双掺杂Eu3+,Tb3+的光谱性能及能量传递过程

采用溶胶凝胶法制备不同配比的Y2O3∶Eu3+、Y2O3∶Tb3+和Y2O3∶Eu3+,Tb3+荧光粉.并通过XRD、SEM和激发、发射光谱对其结构和发光性能进行了研究,用能级图解释了激活剂之间的能量传递关系.结果表明,材料结晶良好,粒度分别为20、31nm和17nm左右,样品形貌类似片状结构.(Y110Eu)2kO3和(Y110Tb)2kO3配比时相对发光强度最高.而共掺杂时,存在着强烈的Eu3+向Tb3+的能量转移,导致红色发光强度的降低而敏化了绿光和蓝光的发射.分析可知,除了激活剂的含量对发光性能有强烈的影响之外,不同的激发波长对体系混合光的形成有很大的影响.当在305nm的激发波长下,可以得到红绿蓝混合光,实现了通过一种荧光粉的激发,发射出近白色的光.为改变灯用三基色荧光粉的组成并降低成本奠定了有利的实验基础.     

LED用Sr_((1-1.5x))Mo_(0.8)Si_(0.2)O_(3.8)∶Eu_x~(3+)红色荧光粉的制备及其荧光性能

通过高温固相法合成了LED用红色荧光粉Sr(1-1.5x)Mo0.8Si0.2O3.8∶Eu3x+(x=0.1,0.2,0.3,0.4,0.5)。通过XRD、激发光谱和发射光谱测试了材料的物相组成以及发光性能。x=0.1样品的XRD谱与JCPDS 08-0482(SrMoO4)的标准卡片相同。Eu3+代替晶格中Sr2+的位置成为发光中心。随着Eu3+含量x的增加,593 nm处的5D0-7F1跃迁和614 nm处的5D0-7F2跃迁发射强度会相互转换:当x≤0.4时,以磁偶极5D0-7F1跃迁为主,发射橙色光;而当x=0.5时,以电偶极5D0-7F2跃迁发射为主,发射红光。可能是过量掺杂的Eu3+离子,只能存在于晶格空位形成缺陷,无法占据SrMoO4中Sr2+的格位中,Eu3+在晶格中占据非对称中心的格位,导致电偶极跃迁变成允许跃迁,从而增加了5D0-7F2跃迁,减弱了5D0-7F1跃迁。因此,可以通过调节激活剂的含量获得不同发光色的荧光粉。Eu3+掺杂的硅钼酸锶体系,614 nm激发下,在368 nm处出现宽的基质吸收峰和467 nm处7 F0-5 D2的跃迁峰,且这2处的吸收峰在x=0.5时比x=0.4时...