Wettability of a polytetrafluoroethylene surface by an aqueous solution of two nonionic surfactant mixtures

Measurements of the advancing contact angle (theta) were carried out for an aqueous solution of p-(1,1,3,3-tetramethylbutyl)phenoxypoly(ethylene glycol)s (Triton X-100 (TX100) and Triton X-165 (TX165) mixtures) on polytetrafluoroethylene (PTFE). The obtained results indicate that the wettability of PTFE depends on the concentration and composition of the surfactant mixture. The minimum of the dependence between the contact angle and composition of the mixtures for PTFE for each concentration at a monomer mole fraction of TX100, alpha = 0.8, points to synergism in the wettability of PTFE. This effect was confirmed by the negative values of interaction parameters calculated on the basis of the contact angle and by the Rosen approach. In contrast to Zisman, there was no linear dependence between cos theta and the surface tension of an aqueous solution of TX100 and TX165 mixtures for all studied systems, but a linear dependence existed between the adhesional tension and surface tension for PTFE over the whole concentration range, the slope of which was -1, indicating that the surface excess of the surfactant concentration at the PTFE-solution interface was the same as that at the solution-air interface for a given bulk concentration. Similar values of monomer mole fractions of the surfactants at water-air and PTFE-water interfaces calculated on the basis of the surface tension and contact angles showed that adsorption at these two interfaces was the same. It was also found that the work of adhesion of an aqueous solution of surfactants to the PTFE surface did not depend on the type of surfactant and its concentration. This means that for the studied systems the interaction across the PTFE-solution interface was constant and was largely of Lifshitz-van der Waals type. On the basis of the surface tension of PTFE, the Young equation, and the thermodynamic analysis of the adhesion work of an aqueous solution of surfactant to the polymer surface, it was found that in the case of PTFE the changes in the contact angle as a function of the mixture concentration of two nonionic surfactants resulted only from changes in the polar component of the solution surface tension.     

The wettability of polytetrafluoroethylene and polymethyl methacrylate by aqueous solution of two cationic surfactants mixture

Advancing contact angle (theta) measurements were carried out for aqueous solutions of cetyltrimethylammonium bromide (CTAB) and cetylpyridinium bromide (CPyB) mixtures on polytetrafluoroethylene (PTFE) and polymethyl methacrylate (PMMA). The obtained results indicate that the wettability of PTFE and PMMA by aqueous solutions of CTAB and CPyB mixtures depends on the composition and concentration of the mixture; however, synergism in the wettability does not exist. In the range of low concentrations of aqueous solution mixtures there is a linear dependence between the contact angle and composition of the mixtures, but at a concentration close to CMC a deviation from linear dependence is observed. In contrast to Zisman, there is no linear dependence between costheta and the surface tension of aqueous solution of CTAB and CPyB mixtures, but a linear dependence exists between the adhesional and surface tension, and these lines have a slope -1 and -0.34 for PTFE and PMMA, respectively, which suggests that adsorption of CTAB and CPyB mixtures at water-air and PTFE-water is the same, and the orientation of the CTAB and CPyB molecules at both interfaces in the saturated monolayer should also be the same. Adsorption of these mixtures at water-air interface is considerably higher than at PMMA-water interface, and CTAB and CPyB molecules should be parallelly oriented to PMMA surface in the saturated monolayer. Extrapolation of the straight lines to the points corresponding to the surface tension of aqueous solution, which completely spreads over the PTFE and PMMA surface, gives a critical surface tension of wetting equal to 23.44 and 33.13 mN/m, respectively. The value of 23.44 mN/m is higher than that of the surface tension of PTFE, but the value of 33.13 is lower than that of Lifshitz-van der Waals components of PMMA surface tension. On the basis of the critical surface tension, the surface tension of PTFE and PMMA, the Young equation, and thermodynamic analysis of the adhesion work of aqueous solution of surfactant to polymer surface, it was found that for PTFE and PMMA the changes of the contact angle of aqueous solution of two cationic surfactants mixtures on their surfaces as a function of the solution concentration resulted only from the decrease of the polar component of the solution surface tension.     

Wettability of a glass surface in the presence of two nonionic surfactant mixtures

Measurements of the advancing contact angle (theta) were carried out for aqueous solution of p-(1,1,3,3-tetramethylbutyl)phenoxypoly(ethylene glycol), Triton X-100 (TX100), and Triton X-165 (TX165) mixtures on glass. The obtained results indicate that the wettability of glass depends on the concentration and composition of the surfactant mixture. The relationship between the contact angle and concentration suggests that the lowest wettability corresponds to the concentration of TX100 and TX165 and their mixture near the critical micelle concentration (CMC). The minimum of the dependence between the contact angle and composition of the mixtures for each concentration at a monomer mole fraction of TX100, alpha, equals 0.2 and 0.4 points to synergism in the wettability of the glass surface. In contrast to the results of Zisman ( Zisman, W. A. In Contact Angle, Wettability and Adhesion; Gould, R. F., Ed.; Advances in Chemistry Series 43; American Chemical Society Washington, DC, 1964; p 1 ) there was no linear dependence between cos theta and the surface tension of aqueous solutions of TX100 and TX165 mixtures for all studied systems, but a linear dependence exists between the adhesional tension and surface tension for glass, practically, in the whole concentration range of surfactants studied, the slopes of which are positive in the range of 0.43-0.67. These positive slopes indicate that the interactions between the water molecules and glass surface might be stronger than those between the surface and surfactant molecules. So, the surface excess of surfactant concentration at the glass-water interface is probably negative, and the possibility for surfactant to adsorb at the glass/water film-water interface is higher than that at the glass-water interface. This conclusion is confirmed by the values of the work of adhesion of "pure" surfactants, aqueous solutions of surfactants, and aqueous solutions of their mixtures to the glass surface and by the negative values of glass-water interfacial tension determined from the Young equation in the range of surfactant concentrations corresponding to their unsaturated monolayer at the water-air interface.     

Wettability of polymeric solids by ternary mixtures composed of hydrocarbon and fluorocarbon nonionic surfactants

Contact angle (θ) measurements on poly(tetrafluoroethylene) (PTFE) and polymethyl methacrylate (PMMA) surface were carried out for the systems containing ternary mixtures of surfactants composed of: p-(1,1,3,3-tetramethylbutyl)phenoxypoly(ethylene glycols), Triton X-100 (TX100), Triton X-165 (TX165) and Triton X-114 (TX114), and fluorocarbon surfactants, Zonyl FSN100 (FSN100) and Zonyl FSO100 (FSO100). The aqueous solutions of ternary surfactant mixtures were prepared by adding TX114, FSN100 or FSO100 to binary mixtures of TX100+TX165, where the synergistic effect in the reduction of the surface tension of water (γ(LV)) was determined. From the obtained contact angle values, the relationships between cosθ, the adhesion tension and surface tension of solutions, cosθ and the reciprocal of the surface tension were determined. On the basis of these relationships, the correlation between the critical surface tension of PTFE and PMMA wetting and the surface tension of these polymers as well as the work of adhesion of aqueous solutions of ternary surfactant mixtures to PTFE and PMMA surface were discussed. The critical surface tension of PTFE and PMMA wetting, γ(C), determined from the contact angle measurements of aqueous solutions of surfactants including FSN100 or FSO100 was also discussed in the light of the surface tension changes of PTFE and PMMA under the influence of film formation by fluorocarbon surfactants on the surface of these polymers. The γ(C) values of the studied polymeric solids were found to be different for the mixtures composed of hydrocarbon surfactants in comparison with those of hydrocarbon and fluorocarbon surfactants. In the solutions containing fluorocarbon surfactants, the γ(C) values were different taking into account the contact angle in the range of FSN100 and FSO100 concentration corresponding to their unsaturated monolayer at water-air interface or to that saturated.     

Effect of anionic surfactant and short-chain alcohol mixtures on adsorption at quartz/water and water/air interfaces and the wettability of quartz

Measurements of the advancing contact angles for aqueous solutions of sodium dodecyl sulfate (SDDS) or sodium hexadecyl sulfonate (SHS) in mixtures with methanol, ethanol, or propanol on a quartz surface were carried out. On the basis of the obtained results and Young and Gibbs equations the critical surface tension of quartz wetting, the composition of the surface layer at the quartz-water interface, and the activity coefficients of the anionic surfactants and alcohols in this layer as well as the work of adhesion of aqueous solutions of anionic surfactant and alcohol mixtures to the quartz surface were determined. The analysis of the contact angle data showed that the wettability of quartz changed visibly only in the range of alcohol and anionic surfactant concentration at which these surface-active agents were present in the solution in the monomeric form. The analysis also showed that there was a linear dependence between the adhesion and the surface tension of aqueous solutions of anionic surfactant and alcohol mixtures. This dependence can be described by linear equations for which the constants depend on the anionic surfactant and alcohol concentrations. The slope of all linear dependence between adhesion and surface tension was positive. The critical surface tension of quartz wetting determined from this dependence by extrapolating the adhesion tension to the value equal to the surface tension (for contact angle equal zero) depends on the assumption whether the concentration of anionic surfactant or alcohol was constant. Its average value is equal to 29.95mN/m and it is considerably lower than the quartz surface tension. The positive slope of the adhesion-surface tension curves was explained by the possibility of the presence of liquid vapor film beyond the solution drop which settled on the quartz surface and the adsorption of surface-active agents at the quartz/monolayer water film-water interface. This conclusion was confirmed by the work of adhesion of aqueous solutions of anionic surfactants and short-chain alcohol mixtures to the quartz surface determined on the basis of the contact angle data and molar fraction of anionic surfactants and alcohols and their activity coefficient in the surface layer.     

The adsorption of cetyltrimethylammonium bromide and propanol mixtures with regard to wettability of polytetrafluoroethylene II. Adsorption at polytetrafluoroethylene-aqueous solution interface and wettability

Measurements of contact angles (theta) of aqueous solutions of cetyltrimethylammonium bromide (CTAB) and propanol mixtures at constant CTAB concentration equal to 1x10(-5), 1x10(-4), 6x10(-4) and 1x10(-3) M on polytetrafluoroethylene (PTFE) were carried out. The obtained results indicate that the wettability of PTFE by aqueous solutions of these mixtures depends on their composition and concentration. They also indicate that, contrary to Zisman, there is no linear relationship between cos theta and the surface tension (gamma(LV)), but a linear relationship exists between the adhesional (gamma(LV)cos theta) and surface tension of aqueous solutions of CTAB and propanol mixtures. Curve gamma(LV)cos theta vs gamma(LV) has a slope equal -1 suggesting that adsorption of CTAB and propanol mixtures and the orientation of their molecules at aqueous solution-air and PTFE-aqueous solution interfaces is the same. Extrapolating this curve to the value of gamma(LV)cos theta corresponding to theta=0, the value of the critical tension of PTFE wetting equal 23.4 mN/m was determined. This value was higher than that obtained from contact angles of n-alkanes on PTFE surface (20.24 mN/m). The difference between the critical surface tension values of wetting probably resulted from the fact that at cos theta=1 the PTFE-aqueous solution of CTAB and propanol mixture interface tension was not equal to zero. This tension was determined on the basis of the measured contact angles and Young equation. It appeared that the values of PTFE-aqueous solution of the CTAB and propanol mixtures interface tension can be satisfactorily determined by modified Szyszkowski equation only for solutions in which probably CTAB and propanol molecules are present in monomeric form. However, it appeared that using the equation of Miller et al., in which the possibility of aggregation of propanol molecules in the interface layer is taken into account, it is possible to describe the PTFE-solution interfacial tension for all systems studied in the same way as by the Young equation. On the basis of linear dependence between the adhesional and surface tension it was established that the work of adhesion of aqueous solution of CTAB and propanol mixtures does not depend on its composition and concentration, and the average value of this work was equal to 46.85 mJ/m(2), which was similar to that obtained for adhesion of aqueous solutions of two cationic surfactants mixtures to PTFE surface.     

Adsorption Properties of Hydrocarbon and Fluorocarbon Surfactants Ternary Mixture at the Water-Air Interface

Measurements were made of the surface tension of the aqueous solutions of p-(1,1,3,3-tetramethylbutyl) phenoxypoly(ethylene glycols) having 10 oxyethylene groups in the molecule (Triton X-100, TX100) and cetyltrimethylammonium bromide (CTAB) with Zonyl FSN-100 (FC6EO14, FC1) as well as with Zonyl FSO-100 (FC5EO10, FC2) ternary mixtures. The obtained results were compared to those provided by the Fainerman and Miller equation and to the values of the solution surface tension calculated, based on the contribution of a particular surfactant in the mixture to the reduction of water surface tension. The changes of the aqueous solution ternary surfactants mixture surface tension at the constant concentration of TX100 and CTAB mixture at which the water surface tension was reduced to 60 and 50 mN/m as a function of fluorocarbon surfactant concentration, were considered with regard to the composition of the mixed monolayer at the water-air interface. Next, this composition was applied for the calculation of the concentration of the particular surfactants in the monolayer using the Frumkin equation. On the other hand, the Gibbs surface excess concentration was determined only for the fluorocarbon surfactants. The tendency of the particular surfactants to adsorb at the water-air interface was discussed, based on the Gibbs standard free energy of adsorption which was determined using different methods. This energy was also deduced, based on the surfactant tail surface tension and tail-water interface tension.     

Correlation between surface free energy of quartz and its wettability by aqueous solutions of nonionic, anionic and cationic surfactants

The measurements of the advancing contact angle for water, glycerol, diiodomethane and aqueous solutions of Triton X-100 (TX-100), Triton X-165 (TX-165), sodium dodecyl sulfate (SDDS), sodium hexadecyl sulfonate (SHDS), cetyltrimethylammonium bromide (CTAB) and cetylpyridinium bromide (CPyB) on quartz surface were carried out. On the basis of the contact angles values obtained for water, glycerol and diiodomethane the values of the Lifshitz–van der Waals component and electron-acceptor and electron-donor parameters of the acid–base component of the surface free energy of quartz were determined. The determined components and parameters of the quartz surface free energy were used for interpretation of the influence of nonionic, anionic and cationic surfactants on the wettability of the quartz. From obtained results it was appeared that the wettability of quartz by nonionic and anionic surfactants practically does not depend on the surfactants concentration in the range corresponding to their unsaturated monolayer at water–air interface and that there is linear dependence between adhesional and surface tension of aqueous solution of these surfactants. This dependence for TX-100, TX-165, SDDS and SHDS can be expressed by lines which slopes are positive. This slope and components of quartz surface free energy indicate that the interaction between the water molecules and quartz surface might be stronger than those between the quartz and surfactants molecules. So, the surface excess of surfactants concentration at the quartz–water interface is probably negative, and the possibility of surfactants to adsorb at the quartz/water film–water interface is higher than at the quartz–water interface. This conclusion is confirmed by the values of the adhesion work of “pure” surfactants, aqueous solutions of surfactants and water to quartz surface. In the case of the cationic surfactants the relationship between adhesional and surface tension is more complicated than that for nonionic and anionic surfactants and indicates that the relationship between the adsorption of the cationic surfactant at water–air and quartz–water interface depends on the concentration of the surfactants in the bulk phase.     

苄基取代甜菜碱对聚四氟乙烯表面润湿性的影响

利用座滴法研究了两性离子表面活性剂苄基取代烷基羧基甜菜碱(BCB)和苄基取代烷基磺基甜菜碱(BSB)在聚四氟乙烯(PTFE)表面上的润湿性质,考察了表面活性剂浓度对接触角的影响趋势,并讨论了粘附张力、固-液界面张力和粘附功的变化规律.研究发现,在低浓度时,表面活性剂通过疏水作用吸附到PTFE表面,疏水链苄基取代支链化使其在固-液界面上的吸附明显低于气-液界面,接触角在很大的范围内保持不变.当体相浓度增加到大于临界胶束浓度(cmc)时, BCB和BSB分子在固-液界面上继续吸附,分子逐渐直立,造成PTFE-液体之间的界面张力(γ_SL)进一步降低,表面亲水性增加,接触角随浓度增加明显降低;另一方面, BSB由于具有较大的极性头,在高浓度时空间阻碍作用明显,导致其对PTFE表面润湿性改变程度小于BCB.     

Mutual influence of cetyltrimethylammonium bromide and Triton X-100 on their adsorption at the water–air interface

On the basis of surface tension values of the aqueous solution of cetyltrimethylammonium bromide (CTAB) and Triton X-100 (TX-100) mixtures measured at 293 K as a function of CTAB or TX-100 concentration at constant TX-100 or CTAB concentration, respectively, the real surface area occupied by these surfactants at the water–air interface was established which is inaccessible in the literature. It appeared that at the concentration of the CTAB and TX-100 mixture in the bulk phase corresponding to the unsaturated monolayer at the water air-interface this area is the same as in the monolayer formed by the single surfactant at the same concentration as in the mixture. In the saturated mixed monolayer at this interface the area occupied by both surfactants is lower than that in the single surfactant monolayer corresponding to the same concentration in the aqueous solution. However, the decrease of the CTAB adsorption is lower than that of TX-100 and the total area occupied by the mixture of surfactants is also lower than that of the single one. The area of particular surfactants in the mixed saturated monolayer changes as a function of TX-100 and CTAB mixture concentration and at the concentrations close to CMC or higher the area occupied by both surfactants is the same. The changes of the composition of the mixed surface monolayer are connected with the synergetic effect in the reduction of the water surface tension by the adsorption of CTAB and TX-100 at the water–air interface. This effect was confirmed by the values of the standard Gibbs free energy of adsorption of both individual surfactants and their mixtures with different compositions in the bulk phase determined by using the Langmuir equation if RT instead of nRT was applied in this equation.     

支链化阳离子和甜菜碱表面活性剂对聚四氟乙烯表面润湿性的影响

利用座滴法研究了支链化阳离子表面活性剂十六烷基羟丙基氯化铵(C₁₆GPC)和两性离子表面活性剂十六烷基羧酸甜菜碱(C₁₆GPB)在聚四氟乙烯(PTFE)表面上的吸附机制和润湿性质, 考察了表面活性剂浓度对表面张力、接触角、粘附张力、固液界面张力和粘附功的影响趋势. 研究发现, 低浓度条件下, 表面活性剂疏水支链的多个亚甲基基团与PTFE表面发生相互作用, 分子以平躺的方式吸附到固体界面; 支链化表面活性剂形成胶束的阻碍较大, 浓度大于临界胶束浓度(cmc)时, C₁₆GPC和C₁₆GPB分子在固液界面上继续吸附, 与PTFE作用的亚甲基基团减少, 分子逐渐直立, 固液界面自由能(γ_sl)明显降低. 对于支链化的阳离子和甜菜碱分子, 接触角均在浓度高于cmc后大幅度降低.     

乙二亚甲基-双（十六烷基二甲基溴化铵）稀水溶液的特性

合成并表征了阳离子Gemini表面活性剂乙二亚甲基-α,β-双（十六烷基二甲基溴化铵）（16-2-16）.用表面张力和粘度法确定了其cmc，通过表面张力曲线计算了16-2-16的表面吸附量、吸附分子面积和胶束形成自由能；并用悬滴法测定了16-2-16在空气表面和十二烷界面的动态表（界）面张力.用改进的Washburn方法测定16-2-16水溶液在硅胶粉末表面的接触角，并进一步讨论了16-2-16在硅胶表面的吸附引起的润湿性变化. 探讨润湿性变化与动态张力的关系. 将16-2-16 与溴代十六烷基三甲胺(CTAB)做比较:两种物质在含油硅胶粉末上引起的最高脱油率（实验室模拟驱油）均发生在cmc附近,但16-2-16的最高脱油率是68％， CTAB的是63％.而所用CTAB的cmc比16-2-16的约大50倍,也就是说用16-2-16可以获得更高的脱油率.     

Interaction of Nonionic Surfactant Triton-X-100 with Ionic Surfactants

The interaction in two mixtures of a nonionic surfactant Triton-X-100 (TX-100) and different ionic surfactants was investigated. The two mixtures were TX-100/sodium dodecyl sulfate (SDS) and TX-100/cetyltrimethylammonium bromide (CTAB) at molar fraction of TX-100, α_TX-100 = 0.6. The surface properties of the surfactants, critical micelle concentration (CMC), effectiveness of surface tension reduction (γ_CMC), maximum surface excess concentration (Γ_max), and minimum area per molecule at the air/solution interface (A _min) were determined for both individual surfactants and their mixtures. The significant deviations from ideal behavior (attractive interactions) of the nonionic/ionic surfactant mixtures were also determined. Mixtures of both TX-100/SDS and TX-100/CTAB exhibited synergism in surface tension reduction efficiency and mixed micelle formation, but neither exhibited synergism in surface tension reduction effectiveness.     

Adsorption of Triton X-100 and cetyltrimethylammonium bromide mixture with ethanol at nylon-6–solution interface with regard to nylon-6 wettability: II. Work of adhesion and activity of surfactants at interfaces

On the basis of the values of the surface tension of the aqueous solutions of the Triton X-100 and CTAB mixture with ethanol, the surface tension of nylon-6 and the nylon-6–solution interfacial tension, the activity of the surfactant mixture and ethanol at the nylon-6–solution interface was calculated and compared to that at the solution–air one. For these calculations, the Sprow and Prausnitz equation was applied. The obtained values of the activity were used for the calculations of the work of adhesion of the solution to the polymer surface. The values of the work of adhesion obtained in this way were compared to those determined from the Young–Dupre equation by using the contact angle values of the aqueous solutions of the TX-100 and CTAB mixture with ethanol measured on the nylon-6 surface. The changes of the work of adhesion determined from the Young–Dupre equation were also considered as a function of the surface tension of the solution, its polar component and the interfacial interaction parameter.     

Adsorption of Triton X-100 and cetyltrimethylammonium bromide mixture with ethanol at nylon-6–solution interface with regard to nylon-6 wettability: I. The effect of adsorption on critical surface tension of nylon-6 wetting

The contact angle measurements of the aqueous solutions of p-(1,1,3,3-tetramethylbutyl)phenoxypoly(ethylene glycol) (TX-100) and cetyltrimethylammonium bromide (CTAB) mixture with ethanol on nylon-6 were made in the range of the total concentration of CTAB and TX-100 mixture from 1 × 10^?6 to 1 × 10^?3 M and ethanol from 0 to 17.13 M. In the CTAB and TX-100 mixture the mole fraction of TX-100 was equal to 0; 0.2; 0.4; 0.6; 0.8 and 1. On the basis of the obtained results, the critical surface tension of nylon-6 wetting was determined from the dependence of cosine of contact angle and the adhesion tension as a function of the surface tension of the solution. This tension was compared to the components and parameters of nylon-6 surface tension taken from literature and discussed in the light of the surface excess concentration of the surface active agents at the nylon-6–solution interface calculated from the Lucassen-Reynders equation and the Gibbs isotherm.     

The wettability of polytetrafluoroethylene by aqueous solution of cetylpyridinium bromide and propanol mixtures

Measurements of advancing contact angles (θ) were carried out for aqueous solutions of cetylpyridinium bromide (CPBr) and propanol mixtures at constant CPBr concentration equal to 1 × 10⁻⁵, 1 × 10⁻⁴, 6 × 10⁻⁴, 1 × 10⁻³ M, respectively, on polytetrafluoroethylene (PTFE). The obtained results indicate that the wettability of PTFE by aqueous solutions of these mixtures depends on their composition and concentration. In contrast to Zisman, there is no linear dependence between the cos θ and surface tension of aqueous solutions of CPBr and propanol mixtures (γ_LV), but a linear relationship exists between the adhesion tension and the surface tension of aqueous solutions of CPBr and propanol mixtures which have a slope equal to −1, and between cos θ and the reciprocal of the surface tension of solution. The slope equal to −1 and the intercept on the cos θ axis close to −1 suggest that adsorption of CPBr and propanol mixtures and the orientation of their molecules at aqueous solution–air and PTFE–aqueous solution interfaces are the same. This also suggests that the work of solution adhesion to the PTFE surface does not depend on the concentration of propanol and CPBr. Extrapolation of the straight line to the point corresponding to the surface tension of solution, which completely spreads over the PTFE surface, gives the value of the critical surface tension of PTFE wetting equal to 24.84 mN/m. This value is higher than PTFE surface tension (20.24 mN/m) and the values of the critical surface tension of PTFE wetting determined by other investigators from the contact angle of nonpolar liquids (e.g. n-alkanes). The differences between the value of the critical surface tension obtained here and those which can be found in the literature were discussed on the basis of the simple thermodynamic rules. Using the measured values of the contact angles and Young equation the PTFE–aqueous solution interfacial tension was determined. The values of PTFE–aqueous solution interfacial tension were also calculated from Miller and co-workers equation in which the correction coefficient of nonideality of the surface monolayer was introduced. From comparison of the obtained values it appears that good agreement exists between the values of PTFE–solution interfacial tension calculated on the basis of Young and Miller and co-workers equations in the whole range of propanol concentration.     

The properties of a binary mixture of nonionic surfactants in water at the water/air interface

The behavior of mixed nonionic/nonionic surfactant solutions, that is, p-(1,1,3,3-tetramethylbutyl)phenoxy poly(ethylene glycol)s Triton X-100 (TX100) and Triton X-165 (TX165) have been studied by surface tension and density measurements. The obtained results of the surface tension measurements were compared with those calculated from the relations derived by Joos, Miller, and co-workers. From the comparison, it appeared that by using these two approaches the adsorption behavior of TX100 and TX165 mixtures at different mole fractions can be predicted. The negative deviation from the linear relationship between the surface tension and composition of TX100 and TX165 mixtures in the concentration range corresponding to that of the saturated monolayer at the interface, the values of the parameters of molecular interaction, the activity coefficients, as well as the excess Gibbs energy of mixed monolayer formation calculated on the basis of Rosen and Motomura approaches proved that there is synergism in the reduction of the surface tension of aqueous solutions of TX100 and TX165 mixture when saturation of the monolayer is achieved. The negative parameters of intermolecular interaction in the mixed micelle and calculations based on MT theory of Blankschtein indicate that there is also synergism in the micelle formation for TX100 and TX165 mixture. It was also found that the values of the standard Gibbs energy of adsorption and micellization for the mixture of these two surfactants, which confirm the synergetic effect, can be predicted on the basis of the proposed equations, which include the values of the mole fraction of surfactant and excess Gibbs energy TX100 and TX165 in the monolayer and micelle.     

Synergism in the spreading of hydrocarbon-chain surfactants on polyethylene film-anionic and cationic mixtures by a two-step procedure

A study has been made of the adsorption, interaction, and spreading of mixtures of anionic and cationic surfactants at the aqueous solution/polyethylene (PE) interface. When a drop of an aqueous solution of an anionic or cationic hydrocarbon-chain surfactant is placed on a highly hydrophobic PE film (contact angle of water > 90 degrees ), it spreads to an area very little larger than that of a drop of water of the same volume. If the anionic and cationic hydrocarbon-chain surfactant solutions are mixed prior to being applied to PE film, synergism is small, if any, and the reproducibility of the experimental results is poor. However, when the cationic and anionic aqueous solutions are applied on the PE film in a sequential manner, a remarkable synergism in spreading is observed and the results are very reproducible. The area spread by an aqueous solution of the anionic-cationic mixture may be more than 400 times that of aqueous solutions of the same volume and surfactant concentration of the individual surfactant components. Previous work in this laboratory on surfactant systems showing synergism in spreading on PE film, but only weak interaction at the aqueous solution/air interface, showed that the synergy was due to changes at the aqueous solution/PE interface and not to the changes at the aqueous solution/air or PE/air interface. Investigation of the adsorption behavior at the aqueous solution/solid interface of two of the anionic-cationic mixtures studied here indicates the reason for differences in spreading behavior observed with different anionic-cationic mixtures. The more similar the adsorption tendencies at the solid/aqueous solution interface of the anionic and cationic surfactants, and the closer their adsorption to an equimolar monolayer there, the stronger their interaction there and the greater their enhancement of the spreading. A mechanism is proposed for the synergy in spreading observed, based upon the difference between the surface tension in the precursor film at the spreading interface and that at the top of the spreading drop.     

阳离子和两性表面活性剂对石英表面润湿性的影响

利用座滴法研究了阳离子表面活性剂十六烷基醚羟丙基季铵盐(C16PC)和两性离子表面活性剂十六烷基醚羟丙基羧酸甜菜碱(C16PB)溶液在石英表面上的润湿性质, 考察了表面活性剂类型及浓度对接触角的影响趋势, 讨论了黏附张力和黏附功的变化规律. 研究发现, 两种表面活性剂在高能的石英表面的吸附造成石英-水的界面自由能(γsl)增大. C16PB通过弱相互作用随机吸附到石英表面, 其增大γsl的能力与降低表面张力(γ1g)的能力相当, 接触角(θ)随浓度变化不大. C16PC 随体相浓度增大能够在石英表面通过静电作用形成定向排列的单分子层, 而后在临界胶束浓度(cmc)附近形成双层结构, 接触角随浓度变化的趋势可分为4个区域, 并通过一个极大值.     

Wetting characteristics of aqueous rhamnolipids solutions

The wetting properties of surfactants on solid surfaces form the basis of many industrial and biological processes. The preferential adsorption of the surfactants from aqueous solutions onto solid surfaces alter the adhesion tension of the surface and this behavior may cause partial to complete wetting of the surfaces by the aqueous surfactant solutions. However, different types of surfactants show different wetting characteristics. To study the wetting properties of biologically produced rhamnolipids (RL), advancing contact angles of the aqueous solutions of the RL mixture of R1 and R2 in a ratio of R2/R1=1.1 were measured as a function of surfactant concentration. For a comparison of the wetting performance, sodium dodecyl sulfate (SDS) was chosen as the reference surfactant. A hydrophilic glass surface, a hydrophobic polymer, polyethylene terephthalate (PET), and gold surface were used as the solid surfaces to determine the wetting characteristics of rhamnolipids. At low surfactant concentrations (RL concentration <3x10(-5)M, SDS concentration<3x10(-4)M) contact angle (Theta) varied in a certain range depending on the character of the surfactant interactions with the surface. This was followed by a decrease in contact angle. Parallel to this behavior, at low surfactant concentrations the adhesion tension decreased, then remained constant and an increase at higher surfactant concentrations was obtained on hydrophobic surfaces. On hydrophilic surfaces a steady decrease in adhesion tension was observed with both surfactant solutions.