Ce1-xM′xCa0.2O1.8-0.4x (M=Y,La和Gd)

采用水热法合成了系列双掺杂的萤石结构Ce1-xLnxCa0.2O1.8-0.4x固溶体, 并研究了3种稀土离子对固溶体导电性的影响, 发现掺杂离子半径接近Ce4+时, 体系电导率增大而活化能降低. 同时发现水热合成的Ce1-xLnxCa0.2O1.8-0.4x样品的平均粒度按着掺入离子Y3+, Gd3+, La3+的顺序逐渐减小, 分别为32, 20和15 nm. 这种变化是由于Y3+半径比La3+和Gd3+更接近Ce4+, 因而在水热合成过程中, 掺Y3+的体系更有利于晶粒的生长, 得到的晶体粒度较大.     

高色纯度高热稳定性红色荧光粉Sr3La2Ge3O12:Sm^3+的合成及其性能

通过高温固相法合成了一系列Sr3La2-xGe3O12:xSm^3+(0≤x≤0.04)红色荧光粉,并对样品的形貌、元素组成、晶体结构、发光性能及热稳定性进行了探究。结果表明:样品Sr3La2Ge3O12:xSm^3+为较宽尺寸分布的颗粒,且结构中仅含有Sr、La、Ge、O、Sm等元素。样品Sr3La1.97Ge3O12:0.03Sm^3+的Rietveld结构精修图与实测XRD图完全吻合,具有六方晶系结构。漫反射测试结果显示基质Sr3La2Ge3O12的带宽为5.54 eV,属于宽带隙材料。在404 nm激发下,样品Sr3La2-xGe3O12:xSm^3+(0≤x≤0.04)的最大发射峰位于601nm处,属于Sm^3+的6H5/2→4L13/2能级跃迁。此外,样品Sr3La1.97Ge3O12:0.03Sm^3+的发光性能最佳,其CIE色坐标为(0.5321,0.4601),色纯度高达94.2%,在298-473 K范围内具有较好的热稳定性,测试温度达到423 K时发射强度仍为室温时的81.6%。     

La取代Ba对Ba1-xLaxMn3Al9O19-α催化剂结构及甲烷催化燃烧性能的影响

采用以尿素水解为基础的水热合成法制备了La和Mn取代的六铝酸盐催化剂(Ba1-xLaxMn3Al9O19-α).在Mn含量达到阈值时,研究了不同量的La取代Ba对Ba1-xLaxMn3Al9O19-α的相组成、结构、热稳定性及甲烷催化燃烧活性的影响.当x≥0.4时,水热合成过程中生成的La2(CO3)3在530-580℃分解,800-900℃时与-γAl2O3反应生成LaAlO3钙钛矿相,可抑制由BaCO3分解而生成的Ba2+的固相扩散,从而阻止了BaAl2O4尖晶石相的生成,使Ba2+在固相中保持较高的分散性,促进了六铝酸盐(-βAl2O3)相的形成.当x<0.4时,BaAl2O4尖晶石相的存在引起催化剂比表面积和催化燃烧活性的降低.La3+取代Ba2+后,六铝酸盐结构发生一定程度的扭变.这种扭变越大,所形成的六铝酸盐催化剂的热稳定性越差.Ba1-xLaxMn3Al9O19-α催化剂的甲烷催化燃烧活性随x的增大而增加,x=0.8时催化剂的活性最佳.     

Gd2O3∶Eu3+纳米棒的制备与发光性能

在表面活性剂辅助的水热条件下合成出尺寸均一的Gd2O3∶Eu3+纳米棒, 对其结构和荧光性质进行了表征, 并对其生长机理进行了初步讨论. XRD结果表明, 水热前驱体样品为六方晶相的Gd(OH)3, 经过灼烧之后样品为立方相的Gd2O3. TEM照片表明, 所得样品为直径60 nm、长度约600 nm的纳米棒. 荧光光谱表明, 在波长为254 nm 的紫外光激发下, Gd2O3∶Eu3+纳米棒产生了不同于前驱体的特征红光发射, 对应于Eu3+ 的5D0-7F2跃迁, 表明Gd2O3是红色发光材料的良好基质.     

La1-xCaxMnO3外延薄膜的制备、结构及磁电阻效应

采用溶胶-凝胶旋涂法在单晶LaAlO3 (100)基片上生长了La1-xCaxMnO3(x=0, 0.05, 0.1, 0.2)外延薄膜. 利用X射线衍射仪(XRD)、 原子力显微镜(AFM)、 聚焦离子束系统(FIB)、 X射线光电子能谱分析仪(XPS)、 振动样品磁强计(VSM)和磁性测量系统(MPMS)对样品的结构、 形貌、 价态、 居里温度和磁电阻效应进行了研究. 结果表明, 薄膜为立方钙钛矿结构, 具有明显的(100)外延生长取向和平整的表面. 在居里温度附近, 样品发生铁磁-顺磁转变. 随着Ca2+掺杂量的增加, 样品的居里温度升高, La0.8Ca0.2MnO3的居里温度为264 K. 随温度的变化, 样品发生了金属-绝缘体转变. 样品还具有较大的磁电阻效应, 在H=2.0 T, T=210 K时, La0.95Ca0.05MnO3的磁电阻达到80.9%.     

水热法制备具有高光催化活性的镧掺杂二氧化钛纳米晶

采用水热法合成钛酸钾(K₂Ti₈O₁₇)纳米棒,并将它作为前驱体水热转晶合成TiO₂纳米晶,同时通过在水热体系中引入稀土元素La³⁺实现对TiO₂的La掺杂.考察了不同条件下钛酸盐向TiO₂的转晶过程,发现水热溶液的pH值、温度以及预处理步骤对转晶过程有很大的影响.利用X射线衍射以及透射电子显微镜对样品的晶相和形貌进行了表征.利用电感耦合等离子体原子发射光谱测量了所合成的La掺杂TiO₂样品中的La含量.通过在紫外光下降解甲基橙(MO,10mg/L)测试了La掺杂TiO₂样品的光催化性能.结果表明La掺杂后TiO₂的光催化活性大大提高.在0.15mol/LLa³⁺浓度下180oC水热合成的La掺杂TiO₂样品显示了最佳的光催化活性.其对MO的光催化降解反应常数高达0.11min^-1,大约是空白TiO₂样品的9.20倍,P25TiO₂的3.69倍.     

水热老化对含钯La0．9Sr0．1CoO3－δ／α－A12O3催化性能的影响

以浸渍法制备了α-A12O3负载的含钯La0．9Sr0．1CoO3-δ钙钛矿样品，探讨了水热老化对样品催化CO-NO反应性能的影响，并以XRD，TPR和XPS等对样品在水热老化前后的结构进行了表征．结果表明，钯的引入方式直接影响样品的水热性能．掺钯样品(LaSrCoPd)具有良好的水热性能，经水热老化后，其催化活性显著提高，显示出最好的催化性能；样品中钯离子位于钙钛矿晶相内，形成α-A12O3负载的La0．9Sr0．1Co0.95Pd0.05O3-δ,La0．9Sr0．1CoO3-δ／α-A12O3负载钯的样品(Pd／LaSrCo)具有最高的初活性，但经水热老化后，其催化活性明显降低在水热老化过程中，La0．9Sr0．1CoO3-δ钙钛矿的结构稳定，但含钯钙钛矿晶相中的钯离子迁移聚集成独立的PdO颗粒，较小的PdO颗粒聚集成较大的颗粒．水热老化后，Pd／LaSrCo样品表面裸露的钯原子数目减少．导致其催化活性降低；而LaSrCoPd样品表面裸露的钯原子数目增多，导致其催化活性升高．     

La1-xSrxYO3-α陶瓷的合成及电性能研究

本文采用高温固相法合成了La1-xSrxYO3-α(x=0.00,0.05,0.10,0.15)系列陶瓷样品,用XRD、SEM对样品进行了表征,并用交流阻抗谱、氢泵、氢浓差电池、氧浓差电池等系统地研究了该系列样品的电性能.结果表明,该系列陶瓷样品均为钙钛矿型单斜晶相结构:样品的氢浓差电池电动势的实测值和理论值吻合得很好,表明样品在氢气气氛中为纯离子导体;氢泵测试结果证实了样品在氢气气氛中基本上是质子导体;氧分压与电导率的关系表明样品在高氧分压气氛中是离子(质子+氧离子)和空穴的混合导体.在低氧分压气氛中是离子(质子+氧离子)导体;氧浓差电池测试结果表明样品在干燥的氧化性气氛中是氧离子和空穴的混合导体.     

ABO3型钙钛矿结构的可见光光催化剂LaCo0.5Ti0.5O3的设计与合成

采用溶胶-凝胶法在较低温度条件下设计合成了新型的具有ABO3型钙钛矿结构的三元金属复合氧化物LaCo0.5Ti0.5O3. 通过TG-DTA, XRD, XPS, UV-Vis DRS等测试技术和可见光光催化活性测试对其进行了表征. 结果表明, 与LaCoO3和La2Ti2O7相比, LaCo0.5Ti0.5O3样品表现出相对较高的可见光光催化活性, 并且合成温度较低. 这是由于原料中的Co2+和Ti4+离子通过电荷补偿作用使产物B位的两种金属均以+3价氧化态分布所致.     

多种形貌YF_3:Eu~(3+)纳米发光材料的水热合成与性能比较

在不同表面活性剂辅助的水热条件下合成出纺锤形、花束状、纳米束和削角八面体形的YF3:Eu3+纳米发光材料,对其结构和性能进行了表征.XRD分析表明:样品为结晶良好的正交相YF3.由FESEM与TEM照片可见,不同表面活性剂的条件下,所合成样品的形貌不同.SEAD显示所得样品分别为多晶和单晶结构,EDX显示所得样品中含有F,Y和Eu三种元素.荧光光谱表明:YF3:Eu3+纳米晶的最强发射峰位于591nm,对应Eu3+的5D0→7F1的磁偶极跃迁发射,说明Eu3+占据YF3基质中Y3+晶格点的C2对称格位上.不同形貌样品的荧光光谱强度不同.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Oxygen defect K2NiF4-type oxides: The compounds La2−xSrxCuO4−x2+δ

Oxygen defect K₂NiF₄-type oxides $\text{La}{}_{\mathrm{2?x}}\text{Sr}{}_{\mathrm{x}}\text{CuO}{}_{\mathrm{<mtext>4?</mtext><mtext>x</mtext><mtext>2</mtext><mtext>+\delta </mtext>}}$ have been synthesized for a wide composition range: 0 ≤ x ≤ 1.34. From the X-ray and electron diffraction study three domains have been characterized: orthorhombic compounds with La₂CuO₄ structure for 0 ≤ x < 0.10, tetragonal oxides similar to LaSrCuO₄ for 0.10 ≤ x < 1 and several superstructures derived from the tetragonal cell ( with n = 3, 4, 4.5, 5, 6) for 1 ≤ x ≤ 1.34. The compounds corresponding to 0 < x < 1 differ from the other oxides in that they are characterized by the presence of copper with two oxidation states: + 2 and + 3. A model structure for La_0.8Sr_1.2CuλO_3.4, in which copper has only the + 2 oxidation state, and for which the actual cell is tegragonal—a = 18.80₄ Å and c = 12.94 Å—has been established. The particular structural evolution of these compounds is discussed in terms of a competition between the capability of Cu(II) to be oxidized to Cu(III) and the ordering of oxygen vacancies.     

A study of the spinel materials LiTi2O4 and Li43Ti53O4 by photoelectron spectroscopy

HeI-excited valence-band ultraviolet photoelectron spectra and MgKα-excited Ti-2p X-ray photoelectron spectra are reported for the spinel materials LiTi₂O₄ and $\text{Li}{}_{\mathrm{<mtext>4</mtext><mtext>3</mtext>}}\text{Ti}{}_{\mathrm{<mtext>5</mtext><mtext>3</mtext>}}\text{O}{}_4$. The presence of a Fermi edge in the ultraviolet photoelectron spectrum of LiTi₂O₄ confirms the metallic nature of this material, although the measured density of states at the Fermi energy is much lower than that expected from an independent-electron interpretation of the magnetic susceptibility. This difference is attributed to a strong interaction of the conduction electrons with the lattice vibrations. The localization of conduction electrons that occurs in the final state in the Ti-2p X-ray photoelectron spectrum of LiTi₂O₄ is attributed to a Coulomb interaction with a core hole.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).