Polyurethanes. IV. Effect of poly(propylene glycol) tacticity on the properties of block copolyether-urethanes

Block copolyèther–urethane–ureas containing isotatic polypropylene glycols were synthesized and their dynamic mechanical properties compared to the analogous atactic structures. At poly(propylene glycol) molecular weights below 1000, tacticity appears to have little effect on the stress–strain properties of the block copolymers. At higher molecular weights, the ability of the isotatic polyglycol segments to crystallize under strain can effect cyclic deformation properties.     

Morphological analysis of photocured polyurethane acrylate networks. Correlation with viscoelastic properties

In this paper, we investigate the final morphology of photocured polyurethane acrylates based on polypropylene oxide by means of Transmission Electron Microscopy (TEM), Small Angle X‐ray Scattering (SAXS), and dynamic mechanical measurements. Two interrelated structural features on two different size scales can occur in these systems. TEM analysis demonstrates the presence of inhomogeneities on the length scale of 10–200 manometers, mostly constituted by clusters of small hard units (diacrylated diisocyanate) connected by polyacrylate chains. The bimodal shape of the dynamic mechanical relaxation spectra corroborates this two‐phase structure. Besides, a suborganization of the reacted diisocyanate hard segments inside the polyurethane acrylate matrix is revealed by SAXS measurements, depending on the nature of the hydroxylacrylate used for the synthesis of the precursor. Finally, UV‐exposure time is found to induce modifications on the viscoelastic properties of the final network, even at high double‐bond conversion: this effect can be due to a postreaction and to an increase of the crosslinking density inside the hard segments domains. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 919–937, 1999     

Rheo-optical studies of high polymers. XIV. Study of the deformation mechanism in polymer blends of polypropylene with ethylene–propylene rubber

To clarify the deformation mechanism in polyblends of polypropylene with ethylene–propylene rubber having different compositions, simultaneous measurements of the infrared dichroism with stress and strain under a constant rate of strain of 1.64%/min have been carried out. The orientation function of the crystallographic c axis of polypropylene in the blends has been obtained as a function of strain ranging from 0 to 20% and of polypropylene content ranging from 0.3 to 1.0. These results have been compared with the temperature dependences of the dynamic Young's modulus and of the loss modulus, as well as of stress–strain curves for the same blends. The modulus data analyzed by Kerner's equation reveal the occurrence of phase inversion at polypropylene contents higher than about 0.5, and this is supported by the infrared dichroism data. The strong effect of quenching on crystalline structure and mechanical properties of pure polypropylene has also been elucidated.     

蓖麻油型聚氨酯IPN的结构与性能研究

本文用蓖麻油,甲苯二异氰酸酯和甲基丙烯酸β-羟乙酯组成的加聚型网络(Ⅰ)和蓖麻油,甲苯二异氰酸酯和聚丙二醇组成的缩聚型聚氨酯(Ⅱ),以同步法形成了一组新型的IPN。用动态力学法和固体核磁共振法研究了它们的结构和性能,形成IPN后,力学数据显示出机械强度的提高,动态力学损耗谱上表现出,tanδ的增宽,固体核磁共振谱计算的结果是界面层的比例增高,但界面层比例并不随配比的改变而变化,它揭示出此IPN可能具有壳核结构。     

Studies on thermotropic liquid crystalline polyurethanes. II. Synthesis and properties of liquid crystalline polyurethane elastomers

Three series of novel thermotropic liquid crystalline polyurethane elastomers (TLCPUEs) were studied. Hard segments were formed by using hexamethylene diisocyanate (HDI) reacted with a mesogenic unit, benzene-1,4-di(4-iminophenoxy-n-hexanol), which also acted as a chain extender. Three diols: 1,10-decanediol,poly(oxytetramethylene) glycol (PTMEG) M _n = 1000 and PTMEG M _n = 2000 were used as the soft segments. The effects of soft segments of polyurethanes on the liquid crystalline behavior were studied. Higher molecular weight TLCPUEs were obtained by adding 30?50 mol % of mesogenic segments to diisocyanates. In contrast to a conventional chain extender such as 1,2-ethylene glycol or 1,4-butyl glycol, the synthesized polyurethane elastomers exhibited a mesophase transition by using a mesogenic unit as the chain extender. Mesophase was found for all synthesized LC polyurethanes except of polymers H2-A-12 and H2-A-7. The structures and the thermal properties of all synthesized TLCPUEs were studied by using FTIR spectroscopy, wide-angle x-ray diffraction (WAXD) and DSC measurements, a polarizing microscope equipped with a heating stage, dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA). Mechanical properties were also examined by using a tensilemeter. © 1995 John Wiley & Sons, Inc.     

Oligomer-polymer blends based on solvent-crazed polymers

The feasibility of preparation of oligomer-polymer blends by means of the solvent crazing technique is considered. An analysis of the mechanical behavior of polymers and porosity of deformed films led to the conclusion that polyethylene glycol and polypropylene glycol in their liquid state are adsorption-active environments effective toward PET and HDPE. The stretching of PET and HDPE in these environments follows the mechanisms of classical and delocalized solvent crazing, respectively. The blends based on PET and HDPE containing polyethylene glycol 400, polypropylene glycol 400, and polypropylene glycol 3000 with an amount of the hydrophilic component of 25–45% were prepared. Most blends retained their stability with time. The exception is the PET-PEG 400 blend, which exhibited a sustained release of the liquid component.     

Crystallization and Properties of Novel Polyurethanes Based on the Chain Extender Ethylene Glycol and Aromatic Diisocyanates of Variable Flexibility

Summary: Novel polyurethane elastomers (PUs) were synthesized with ethylene glycol (EG) as a chain extender. The macrodiol was poly(ethylene adipate) (PEA), MW = 2000 ± 50. Two isocyanates were employed: 4,4′-methylene bis(phenyl isocyanate) (MDI) and 4,4′-dibenzyl diisocyanate (DBDI). The conformational mobility of DBDI causes an unusually wide range of mechanical, physical and chemical properties, associated with the possibility of pronounced phase separation into a domain – matrix morphology, and with a higher tendency to crystallization and self-association by hydrogen bonding. Materials were characterized by wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), dynamic mechanical analyses (DMA), and mechanical measurements. Results were discussed in terms of the effect of PUs crystallinity. In the case where the chain extender–diisocyanate couple was EG-DBDI, the hard segments were observed to crystallize. The DBDI based PUs displayed higher flow stress in the hard phase caused by stronger phase segregation.     

Polyisobutylene‐based polyurethanes. VI. Unprecedented combination of mechanical properties and oxidative/hydrolytic stability by H‐bond acceptor chain extenders

We describe the design, synthesis, characterization, and testing of novel polyurethanes (PUs) exhibiting unprecedented combinations of outstanding mechanical properties and oxidative/hydrolytic stabilities. This achievement is due to the use of polyisobutylene (PIB) soft segments plus flexible H‐bond acceptor chain extenders (HACEs): the PIB imparts superior oxidative/hydrolytic stability and the HACE produces reinforcing H‐bonds, which lead to outstanding mechanicals. Oxidative/hydrolytic stability was quantitated by retention of tensile strength and elongation after exposure to nitric acid. PUs containing 60–70% PIB retain their mechanical properties, whereas Carbothane®, Bionate®, and Elast‐Eon?, PUs marketed for chemical stability, degrade severely under the same conditions. Various HACEs were identified (e.g., hexaethylene glycol, tripropylene glycol, tributylene glycol, 3,3′‐diamino‐N‐methyl‐dipropylamine, etc.) and their effect on mechanical properties was investigated. A PIB‐ and HACE‐containing PU exhibited 29.2 MPa tensile strength, 620% elongation, and 80 Shore A hardness. Properties were analyzed in terms of stress–strain profiles, differential scanning calorimetry traces, dynamic mechanical thermal analysis plots, and oxidative/hydrolytic stability. The properties of various PIB‐based rubbers, that is, thermoplastic PUs, SIBSTAR®, and thermoset butyl rubber are compared. The novel PUs are promising candidates for biomaterials and industrial applications where a combination of mechanical properties and oxidative/hydrolytic stability is of the essence. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2361–2371, 2010     

Shape memory polyurethanes based on recycled polyvinyl butyral. I. Synthesis and morphology

Shape memory polyurethanes (SMPUs) were synthesized by 4,4′-diphenylmethane diisocyanate (MDI), hexane-1,6-diol (HD), polypropylene glycol (PPG), and recycled polyvinyl butyral (PVB). Dynamic mechanical analysis, differential scanning calorimetry and Fourier transformation infrared attenuated total reflection spectroscopy was used to characterize the poly (vinylbutyral-urethanes). Micro-phase domain separation of hard and soft segments and phase inversion were investigated. Increasing the hard segment content, i.e., average hard segment molecular weight, leads to an increase in the degree of micro-phase separation, hard domain order and crystallinity. The crystalline hard segment structures combined with the elastic nature of soft segment matrix provide enough physical and chemical crosslinks to have shape memory effect.     

Effect of montmorillonite treatment with supercritical CO2 on the morphology and properties of polypropylene nanocomposites

The effects of montmorillonite (MMT) treatment with supercritical carbon dioxide (SC-CO₂) on clay morphology and the properties of polypropylene nanocomposites were investigated by wide-angle X-ray diffraction, transmission electron microscopy, scanning electron microscopy, dynamic mechanical analysis, and differential scanning calorimetry. The use of poly(propylene glycol) (PPG) was evaluated. The results showed that the MMT morphology (structure formation, dispersion, and orientation) was affected by treatment with SC-CO₂, and the use of PPG, or the use of CO₂ in the liquid state. Consequently, different reinforcement measurements were obtained. The relationship between structure and properties was reported.     

Block copolyurethanes based on polyoxytrimethylene glycols

Trimethylene oxide was polymerized to polyoxytrimethylene glycol by two synthetic routes. High molecular weight polytrimethylene oxide was synthesized using a coordination catalyst system consisting of triethylaluminum, acetylacetone, and water, then ozonized and reduced with lithium aluminum hydride in anhydrous ether to form hydroxyl end-capped polyoxytrimethylene glycol. In the second route, the polyoxytrimethylene glycols were synthesized directly by the cationic polymerization of trimethylene oxide with boron trifluoride/ethyl ether as catalyst and 1,4 butanediol as co-initiator. (AB)_n block copolyether–urethane–ureas based on these polyoxytrimethylene glycols were synthesized and characterized by differential scanning calorimetry, and dynamic mechanical and stress–strain measurements.     

Study of molecular mobility in ultraoriented polypropylene by the spin-probe technique

The rotational mobility of nitroxide radicals in polypropylene samples with draw ratios varying from 1 to 18 has been studied between 30 and 110°C by the ESR technique. The drop in the rotational frequency with increasing orientation correlates very well with the behavior of various other measures of molecular mobility such as organic vapor sorption, proton spin–spin relaxation times from NMR, and dynamic mechanical loss factor. This implies that each of these parameters is a good indicator of the amount of free volume in the amorphous regions. Annealing at high temperature relaxes the amorphous chain segments, thereby increasing the spin-probe rotational frequency in the drawn samples to values even higher than that in the quenched isotropic material.     

脂肪族水性聚氨酯的动态力学行为研究

合成了一系列脂肪族水性聚氨酯 .考察了软段的组成、软段分子量及DMPA用量对产物动态力学性能的影响作用 .实验结果表明 ,软段的化学结构对水性聚氨酯的相态结构影响很大 .聚醚型水性聚氨酯具有较低的软段玻璃化转变温度 (Tgs) .聚醚型产物的微相分离程度高于聚酯型产物 .当采用聚酯和聚醚二元醇为混合软段时 ,Tgs随软段中聚醚含量的提高而逐渐降低 .提高DMPA用量 ,软段玻璃化转变温度Tgs移向低温区 ,硬段玻璃化转变温度Tgh移向高温区 ,说明体系的微相分离程度加大 .当软段分子量较低时 ,产物为半相容结构 ,只有一个主转变峰 ,软段的玻璃化转变以肩峰的形式出现 ;当软段分子量较高时 ,产物的微相分离程度较高 ,可以分别观察到软段及硬段的玻璃化转变 .总之 ,通过改变软段的种类、组成和分子量以及DMPA用量 ,可以大幅度地改变水性聚氨酯的形态结构 .     

New multiblock poly(ether-ester)s based on poly(trimethylene terephthalate) as rigid segments

A series of novel poly(trimethylene terephthalate)-block-poly(tetramethylene oxide) (PTT--PTMO) segmented block copolymers were synthesised by transesterification in the melt of dimethyl terephthalate, 1,3-propanediol and poly(tetramethylene oxide) glycol (PTMO, 1000 g/mol). A range of multiblock copolymers were synthesized, with flexible PTMO segments contents varying from 20 to 80 wt%. The novel poly(ether-block-ester)s were characterized by using viscometry, hardness measurements, differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile properties.     

THERMOPLASTIC ELASTOMERS. II. POLY(ETHER-ESTER-IMIDE)S BASED ON 1,4-DIAMINOBUTANE,TRIMELLITIC ANHYDRIDE, 1,4-DIHYDROXYBUTANE,AND POLY(ETHYLENE OXIDE)S

A series of new poly(ether-ester-imide)s, PEEIs, was prepared from an imide dicarboxylic acid based on 1,4-diaminobutane and trimellitic anhydride. This imide dicarboxylic acid polycondensed with 1,4-dihydroxybutane formed the hard segments and poly(ethylene oxide), PEO-1000, or mixtures of PEO-1000 and poly(tetramethylene oxide), PTMO-1000, were used as soft segments. Whenever PTMO-1000 was used as comonomer, macrophase separation was observed at the end of the polycondensation. However, this macrophase separation had little influence on the mechanical properties. A poly(ether-esterimide), PEEI, containing neat PEO-1000 was characterized by dynamic mechanical thermoanalysis, stress-strain and hysteresis measurements, and by melt rheology. The mechanical properties were compared with those of an analogous PEEI containing neat PTMO-1000 and with those of a poly(ether-ester), PEE, based on poly(butylene terephthalate) hard segments and PTMO-1000.     

Novel AB crosslinked polymer networks from telechelic 4‐vinylbenzyl carbamate terminated polyurethanes and different vinyl monomers

Novel AB crosslinked polymer (ABCP) networks were synthesized from telechelic 4‐vinylbenzyl carbamate terminated polyurethanes and monomers such as styrene, 4‐vinylpyridine, methyl methacrylate and butyl acrylate. Telechelic 4‐vinylbenzyl carbamate terminated polyurethanes were synthesized from polypropylene glycol‐based NCO‐terminated polyurethane and vinylbenzyl alcohol. Effect of changing the molecular weight of polypropylene glycol on the static and dynamic mechanical properties of ABCP networks from polyurethane‐polymethyl methacrylate was studied in detail. Dynamic mechanical thermal analysis results show that polymethyl methacrylate and polystyrene‐based ABCPs have good damping over a broad temperature range. ABCP networks prepared from 4‐vinylbenzyl carbamate terminated polyurethane and different monomers such as methyl methacrylate, butyl acrylate and styrene exhibit single tan δ_max value which implies excellent interlocking between the two polymers present in the ABCP networks. Static mechanical studies showed that methyl methacrylate and styrene‐based ABCP networks exhibit better tensile properties compared to other ABCP networks from butyl acrylate and 4‐vinyl pyridine monomers. Thermogravimetric analysis results revealed that the ABCP networks showed an improved thermal stability. Copyright © 2009 John Wiley & Sons, Ltd.     

Melt amination of polypropylenes

Amine (primary and secondary) functional polypropylenes were prepared by the melt blending of maleated polypropylenes with small diamines, including hexamethylenediamine (primary–primary diamine), p‐xylylenediamine (primary–primary diamine), and N‐hexylethylenediamine (primary–secondary diamine), at various diamine/anhydride molar ratios in a batch mixer and a twin‐screw extruder. The experimental conversion data by Fourier transform infrared nearly agreed with the assumption of a complete reaction between the primary amine and anhydride. Chain extensions of the maleated polypropylenes by the diamines were monitored by the torques during mixing and further evaluated by rheological (dynamic shear rheometry) and mechanical measurements. We show that these amino polypropylenes are very effective adhesion promoters and compatibilizers of thermoplastic polyurethanes with polypropylene. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4217–4232, 2005     

Preparation and characterization of a new class of poly(ether‐block‐amide)s via solvent free reactive processing

Novel poly(ether‐co‐amide) block copolymers (PEA) with polyamide‐6 as hard segments and different polyether (polyoxytetramethylene glycol [PTMG]/polyethylene glycol [PEG]) as soft segments were prepared via reactive processing. The chemical structure, crystalline properties, mechanical properties, water resistance, and thermal stability of as‐prepared PEAs were extensively studied by Fourier transform infrared spectroscopy, X‐ray diffraction, differential scanning calorimetry, dynamic mechanical analysis, tensile testing, water contact angle, water absorption, and thermal gravity analysis. Fourier transform infrared spectroscopy confirmed the chemical structure and composition of PEAs. The X‐ray diffraction and differential scanning calorimetry showed that PEAs consist of obvious crystalline polyamide‐6 hard segments and that the crystalline structure of PEG will be significantly changed with the addition of PTMG. Dynamic mechanical analysis and tensile testing showed that the obtained PEAs exhibit classical elastomeric rubber plateau and tensile behavior. Meanwhile, the introduction of PTMG will improve the mechanical properties of PEAs. PEA with PEG as soft segments exhibited extremely surface hydrophilicity and high water absorption of 127%; the increasing of PTMG content in soft segments will reduce the surface hydrophilicity and improve the water resistance. In addition, the obtained PEAs exhibited good thermal stability, which will meet requirement of multiple processing.     

Structure and properties of propylene-ethylene block copolymers and the corresponding blends

Structure and properties of presumed polypropylene(PP)-b-polyethylene(PE) block copolymers (PPPE) and the corresponding blends (PP/PE) have been investigated by wide-angle x-ray scattering (WAXS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), torsional pendulum apparatus, and other techniques measuring mechanical properties. Crystallinity, morphological structure, and mechanical properties of the block copolymers and blends vary with the PP and PE compositions. Compared with PP homopolymers and PP/PE blends, PP and PE segments in PP-PE block copolymers have a reduced crystallinity, especially PE segments. An additional peak at about ?40°C is observed in dynamic relaxation spectra; substantially different morphology is revealed; and mechanical properties are greatly improved for the sequentially copolymerized PP-PE block copolymers, indicating the existence of PP-PE block structure.     

脂肪族水性聚氨酯的力学性能研究

考察了软段的种类、分子量大小、混合软段的组成对产物力学性能的影响作用。同时还研究了二羟甲基丙酸(DMPA)用量以及中和剂的影响作用．实验结果表明。软段结构对脂肪族水性聚氨酯成膜的力学性能影响很大，聚酯型产物具有较高的模量和拉伸强度。聚醚型产物则具有较高的伸长率．混合软段对产物力学性能的影响较为复杂，随着软段中聚醚含量的升高，产物的硬度和模量均大幅度下降，但拉伸强度和伸长率的变化并不是一个线性关系．产物的模量随软段分子量的提高而降低，但伸长率和拉伸强度却有所提高．当DMPA用量较高时。产物的模量和拉伸强度均较高：当DMPA用量较低时，产物则具有较高的伸长率．中和剂的种类对产物力学性能的影响明显，当以NaOH为中和剂时，产物具有较高的硬度、模量、拉伸强度：以三乙胺为中和剂时，产物具有较高的伸长率．