Reaction of oxygen with adsorbed hydrogen species of a reduced Pt/TiO2 catalyst

Reaction of oxygen with the adsorbed hydrogen species of Pt/TiO₂ catalysts reduced in the temperature range of RT-773 K has been studied by temperature-programmed oxidation (TPO). It is obtained that the Pt-assisted reaction of oxygen with both the surface hydroxy groups and titanium hydride species occurs in the temperature range of 320–450 K; direct oxidation of the surface hydrogen species takes place on the surface of TiO₂ in the temperature range of 500–600 K; and oxygen reacts with the stored hydrogen species in the sublayer and bulk of the TiO₂ support when the temperature was increased to above 600 K.     

Catalytic activity of NiMo/TiO2?Al2O3 systems in thiophene hydrodesulfurization

A correlation exists between the number of surface acid sites and the catalytic activity of NiMo/TiO₂–Al₂O₃ systems in thiophene hydrodesulfurization. The catalytic activity for thiophene hydrodesulfurization and surface concentration of Brönsted acid sites increase with the titania content in the TiO₂–Al₂O₃ support.     

Cyclohexanol dehydrogenation over Cu/SiO2 and CuO/SiO2: A comparison

Various CuO/SiO₂ catalysts were prepared and characterized by XRD, surface area and metal area measurements. While dehydrogenation activity for cyclohexanol was observed at 473–573 K on reduced catalysts, it was observed only at 573 K on the unreduced catalyst.IICT Communication No: 3261     

Pulsed laser-induced oxygen deficiency at TiO2 surface: Anomalous structure and electrical transport properties

We have studied pulsed laser-induced oxygen deficiencies at rutile TiO₂ surfaces. The crystal surface was successfully reduced by excimer laser irradiation, and an oxygen-deficient TiO_2−δ layer with 160 nm thickness was formed by means of ArF laser irradiation at 140 mJ/cm² for 2000 pulses. The TiO_2−δ layer fundamentally maintained a rutile structure, though this structure was distorted by many stacking faults caused by the large oxygen deficiency. The electrical resistivity of the obtained TiO_2−δ layer exhibited unconventional metallic behavior with hysteresis. A metal–insulator transition occurred at 42 K, and the electrical resistivity exceeded 10⁴ Ω cm below 42 K. This metal–insulator transition could be caused by bipolaronic ordering derived from Ti–Ti pairings that formed along the stacking faults. The constant magnetization behavior observed below 42 K is consistent with the bipolaronic scenario that has been observed previously for Ti₄O₇. These peculiar electrical properties are strongly linked to the oxygen-deficient crystal structure, which contains many stacking faults formed by instantaneous heating during excimer laser irradiation.     

Interface-reactions of Pt/TiO2: Comparative electrical, XPS-, and AES-depth profile investigations

Summary Pt/TiO₂-interfaces show Schottky-barrier or ohmic behavior depending on the diffusion of Pt into TiO₂ subsurface layers. Diffusion effects are negligible for TiO₂ rutile surface structures in the absence of oxygen at T1070 K. This leads to Schottky-barrier electrical behavior. If bulk diffusion of Pt is pronounced we observe ohmic behavior. This is the case for all TiO₂ samples with nonstoichiometric Magneli-subsurface phases and for TiO₂ rutile surface phases at T1070 K in the presence of oxygen. The latter is explained by reduced activation barriers of surface platinum during the first step of in-diffusion if platinum is present as an ion (Pt⁴⁺ or Pt²⁺) at the surface. Ions are formed as intermediates during the formation and decomposition of platinum oxide at the three-phase-boundary O₂/Pt/TiO₂.     

Hydrogen desorption of reduced Pt/TiO2 catalyst

The temperature-programmed desorption of hydrogen from a Pt/TiO₂ catalyst reduced in a wide temperature range (RT-773 K) has been studied. It is found that the presence of labile surface oxygen species increases the amount of hydrogen species formed at room temperature, and greatly decreases the quantities of adsorbed hydrogen species at medium temperatures. After the catalyst was reduced at high temperature, it is observed that two strong hydrogen desorption peaks appear at 450–600 K and above 600 K, which are ascribed to surface titanium hydride and the hydrogen species stored in the sublayer and bulk of the support, respectively.     

TSL and EPR studies of SrBPO5 doped with CeO2and co-doped with CeO2 and Sm2O3

Thermally stimulated luminescence (TSL) and electron paramagnetic resonance (EPR) investigations were carried out on gamma irradiated SrBPO₅ samples doped with CeO₂ and co-doped with CeO₂ and Sm₂O₃. On gamma-irradiation at room temperature, BO₃ ^2–, O₂ ^– and O^– radicals were produced. It was seen that the O^– radical ion disappeared in the sample annealed at 500 K. It is proposed that the recombination between trapped electrons and O^– radical ions results in transfer of recombination energy to the impurity centre Ce³⁺ resulting in TSL glow peak at 485 K. In the case of co-doped samples energy transfer occurs between Ce³⁺ to Sm³⁺ resulting in increase in the intensity of glow peak at 485 K.The authors are grateful to Dr. V. K. Manchanda, Head, Radiochemistry Division, BARC for his keen interest and encouragement during the course of this work.     

The influence of La2O3 and TiO2 on NiO/MgO/α-Al2O3

Summary The effect of La₂O₃ and TiO₂ on product selectivity, methane conversion and coke formation over NiO/MgO/ α -Al₂O₃ catalyst were studied in a simultaneous steam and CO₂ reforming of methane to syngas. La₂O₃ and TiO₂ were added to the catalyst via incipient wetness impregnation and bulk precipitation techniques and catalyst activity was tested in a fixed bed quartz reactor. Results reveal that although the addition of these oxides has no effect on the product selectivity and methane conversion, but can reduce coke formation on the surface of the catalysts as it can enhance the mobility of lattice oxygen anions. The results further show that the catalysts prepared by bulk precipitation technique decrease the coke formation more effectively.     

Conversion of NO in NO/N2, NO/O2/N2, NO/C2H4/N2 and NO/C2H4/O2/N2 Systems by Dielectric Barrier Discharge Plasmas

An experimental study on the conversion of NO in the NO/N₂, NO/O₂/N₂, NO/C₂H₄/N₂ and NO/C₂H₄/O₂/N₂ systems has been carried out using dielectric barrier discharge (DBD) plasmas at atmospheric pressure. In the NO/N₂ system, NO decomposition to N₂ and O₂ is the dominating reaction; NO conversion to NO₂ is less significant. O₂ produced from NO decomposition was detected by an on-line mass spectrometer. With the increase of NO initial concentration, the concentration of O₂ produced decreases at 298 K, but slightly increases at 523 K. In the NO/O₂/N₂ system, NO is mainly oxidized to NO₂, but NO conversion becomes very low at 523 K and over 1.6% of O₂. In the NO/C₂H₄/N₂ system, NO is reduced to N₂ with about the same NO conversion as that in the NO/N₂ system but without NO₂ formation. In the NO/C₂H₄/O₂/N₂ system, the oxidation of NO to NO₂ is dramatically promoted. At 523 K, with the increase of the energy density, NO conversion increases rapidly first, and then almost stabilizes at 93–91% of NO conversion with 61–55% of NO₂ selectivity in the energy density range of 317–550 J L⁻¹. It finally decreases gradually at high energy density. A negligible amount of N₂O is formed in the above four systems. Of the four systems studied, NO conversion and NO₂ selectivity of the NO/C₂H₄/O₂/N₂ system are the highest, and NO/O₂/C₂H₄/N₂ system has the lowest electrical energy consumption per NO molecule converted.     

组合型Pt/TiO_2催化剂用于低温催化甲苯完全氧化

将均匀分布的纳米Pt粒子直接吸附到TiO2载体上,即制得了组合型Pt/TiO2催化剂(Pt/TiO2-AS).与浸渍法制备的Pt/TiO2催化剂(Pt/TiO2-WI)比较,Pt/TiO2-AS催化剂在催化甲苯完全氧化反应中表现出了很好的催化性能,甲苯转化率为100%时的反应温度低至150°C,而且即使在较高甲苯浓度和较高气体空速下,该催化剂也能保持较好的催化性能.通过X射线衍射(XRD)、N2吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、氢气程序升温还原(H2-TPR)及傅里叶变换红外(FTIR)光谱等对两种Pt/TiO2催化剂的结构和表面性能进行了表征.结果表明组合型Pt/TiO2-AS催化剂粒径小(2.5 nm),活性组分主要以Pt0形式存在且分布在载体表面,而且载体表面Ti―O键活化使催化剂具有较强的催化氧化能力.另外,活性中心的价态变化(Pt0→Ptδ+)是导致Pt/TiO2-AS催化剂失活的主要原因.     

Lithium-promoted V2O5?TiO2 catalysts for o-xylene oxidation to phthalic anhydride

A V₂O₅–Li₂O–TiO₂ (a) based catalyst for o-xylene oxidation to phthalic anhydride has been synthesized. The activity and selectivity of the specimen obtained are comparable with those of industrial catalysts.     

Photooxidation of Ethylbenzene with TiO 2 and Metal Coated TiO 2 and its Kinetics

Photooxidation of ethylbenzene with oxygen to give ethylbenzene hydroperoxide has been achieved in a stirred photochemical reactor that was cooled by a water system by irradiation with a 400W high-pressure mercury lamp and using TiO₂ powder and metal coated TiO₂. The effects of the amount of copper or silver coated on TiO₂ and of the temperature on the rate of oxidation have been investigated. It is suggested that thermal cleavage of the O–O bond and photochemically generated singlet oxygen should be considered as the initiating step in a radical chain mechanism. An optimum loading of 6% Ag or 4–5% Cu was observed for photooxidation of ethylbenzene.     

Synthesis and characterization of sodium titanates Na2Ti3O7 and Na2Ti6O13

Na₂Ti₃O₇ and Na₂Ti₆O₁₃ were synthesized by sol-gel method in order to obtain pure phases. Different heat-treatments were applied on powders and pellets of these materials. The effects were studied by XRD, dilatometry, TGA-DTA, SEM and electrochemical impedance spectroscopy. Pure Na₂Ti₃O₇ was obtained at 973 K. Sintering at 1373 K caused a partial decomposition into Na₂Ti₆O₁₃. The Na₂Ti₃O₇ powder sintered at 1273 K showed polygonal microstructure. Na₂Ti₃O₇ pellets sintered at 1323 K for 10 h exhibited large structures. This latter microstructure decreased the electrical conductivity of Na₂Ti₃O₇. Pure Na₂Ti₆O₁₃ was obtained at 873 K. Sintering at 1073 K caused a partial decomposition into TiO₂ (rutile). Na₂Ti₆O₁₃ pellets sintered at 1323 K for 10 h exhibited common shrinkage behavior. This shrinkage process increased the electrical conductivity of this material. The presence of TiO₂ resulted in a oxygen partial pressure dependence of the electrical conductivity.     

Catalytically Promoted NOx Sorption by ZrO2-Based Oxides

Metal promoted zirconia-based oxide sorbents, such as Pt–ZrO₂/Al₂O₃ for NO _x have been investigated. To clarify the role of the catalyst component, sorption of NO and NO₂ was compared using the samples with and without Pt. The catalytic oxidation of NO to NO₂ and successively to nitrate ions is an important role for the Pt catalyst. The experimental results indicate that a high-temperature calcination is essential to remove residual Cl from Pt–ZrO₂–Al₂O₃ prepared from H₂PtCl₆ in order to provide more active NO _x sorption sites. Of M–ZrO₂–Al₂O₃ samples investigated, ruthenium as well as Pt demonstrated relatively good performance as a catalyst component in the sorbent. The FT-IR spectra after sorption of NO and NO₂ demonstrated a strong band attributed to stored nitrate ions. The Pt catalyst was more resistant to sulfur poisoning than a base metal catalyst. However, the NO _x sorptive capacities of the Pt–ZrO₂/Al₂O₃ sorbents were expected to be deteriorated in dilute SO₂ as far as observed from FT-IR spectra.     

Ethene hydrogenation by Rh/TiO2 under SMSI conditions

Hydrogenation of ethene has been studied at 185–230 K on a Rh/TiO₂ catalyst reduced at 473–773 K. The activity decreases on increasing the reduction temperature, even at 500 K, but it is more evident when reduction is carried out at 773 K. Oxidation and reduction recovers the activity in hydrogenation.     

Tunneled Intergrowth Structures in the Ga2O3–In2O3–SnO2 System

The structures of several Ga₂O₃–In₂O₃–SnO₂ phases were investigated using high-resolution electron microscopy, X-ray diffraction, and Rietveld analysis of time-of-flight neutron diffraction data. The phases, expressed as Ga_4−4xIn_4xSn_n−4O_2n−2 (n=6 and 7–17, odd), are intergrowths between the β-gallia structure of (Ga,In)₂O₃ and the rutile structure of SnO₂. Samples prepared with n≥9 crystallize in C2/m and are isostructural with intergrowths in the Ga₂O₃–TiO₂ system. Samples prepared with n=6 and n=7 are members of an alternative intergrowth series that crystallizes in P2/m. Both intergrowth series are similar in that their members possess 1-D tunnels along the b axis. The difference between the two series is described in terms of different crystallographic shear plane operations (CSP) on the parent rutile structure.     

Effect of sol-gel derived Al2O3-ZrO2 and Al2O3-TiO2 oxides on the selectivity of NO reduction by CO under oxidizing conditions

The role of Al₂O₃-ZrO₂ and Al₂O₃-TiO₂ sol-gel prepared supports in the activity of platinum for the NO reduction by CO under oxidizing conditions has been studied. ²⁷Al MAS-NMR spectra have shown the formation of pentacoordinate Al^V in alumina-zirconia support. ZrO₂ or TiO₂ crystalline phases cannot be identified by XRD diffraction, suggesting the formation of nanosized structures supported on alumina. When the reaction was carried out in presence of oxygen, large amounts of NO₂ were observed on Pt/Al₂O₃-ZrO₂catalyst, while the formation of N₂O is more prononced on Pt/Al₂O₃-TiO₂ catalyst. The effect of water during NO reduction is discussed. This revised version was published online in June 2006 with corrections to the Cover Date.     

Topotaxial formation of titanium-rich barium titanates during solid state reactions on (110) TiO2 (rutile) and (001) BaTiO3 single crystals

The orientation relationships of Ti-rich barium titanate phases formed by solid state reactions at high temperatures were studied using (110) TiO₂ (rutile) and (001) BaTiO₃ single-crystal substrates. Well-oriented Ba₆Ti₁₇O₄₀ islands were observed after a vapor–solid reaction of a BaO quantity equivalent to a nominal BaO film thickness of 1 nm with the TiO₂ substrate, whereas a thin film consisting of well-oriented BaTiO₃ and Ba₆Ti₁₇O₄₀ grains was formed after vapor–solid reaction of a BaO quantity equivalent to a nominal BaO film thickness of 50 nm with the rutile substrate. A topotaxial orientation relationship between Ba₆Ti₁₇O₄₀ and TiO₂ was found. Topotaxy is facilitated by a certain similarity in the oxygen sublattices of TiO₂ and Ba₆Ti₁₇O₄₀. The mechanism of the reaction occurring between BaO vapor and the TiO₂ surface at high temperature is discussed. On the other hand, several well-oriented Ba₄Ti₁₃O₃₀, Ba₆Ti₁₇O₄₀ and Ba₂Ti₅O₁₂ phases were observed to be embedded in the mainly forming Ba₂TiSi₂O₈ phase after a solid–solid reaction of amorphous SiO₂ thin films with (001) BaTiO₃ substrates at temperatures above 1000 °C. They were formed by a topotaxial reaction involving the transformation of (111) planes of BaTiO₃ into (001) planes of the Ti-rich phases by removal of BaO and insertion of TiO₂. Cross-sections of the interfaces between the substrates and the various reaction products are studied by (high-resolution) transmission electron microscopy.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

Relationship between sulfur dioxide oxidation and selective catalytic NO reduction by ammonia on V2O5?TiO2 catalysts doped with WO3 and Nb2O5

The performance of V₂O₅–TiO₂ catalysts doped by WO₃ and Nb₂O₅ in sulfur dioxide oxidation, and in selective catalytic reduction (SCR) of NO by ammonia has been studied. Addition of tungsten and niobium oxides was found to suppresses sulfur dioxide oxidation thus increasing the catalysts resistance to SO₂ poisoning and their activity in SCR.