Electrochemical kinetics of nanosized Ag and Ag2O thin films prepared by radio frequency magnetron sputtering

Ag and Ag₂O thin films have been prepared by radio frequency magnetron sputtering on Cu substrates and have been characterized by X-ray diffraction, scanning electron microscope and atomic force microscope. The electrochemical performance of the thin films has been studied by galvanostatic cycling and cyclic voltammetry. The potential dependence of Li-ion chemical diffusion coefficients, [(D)\tilde]_\textLi {\widetilde{D}_{\text{Li}}} , of the films has been determined by galvanostatic intermittent titration technique and electrochemical impedance spectroscopy. It is found that Li-ion chemical diffusion coefficients of the Ag film range from 10⁻¹⁶ to 3 × 10⁻¹⁴ cm² s⁻¹. The Ag/Li₂O composite that is formed from Ag₂O after the first cycle exhibits higher [(D)\tilde]_\textLi {\widetilde{D}_{\text{Li}}} values than the Ag film, especially at a low Li-intercalation content. The phase transitions in the two-phase region cause a significant decrease of chemical diffusion coefficients.     

Determination of hemoglobin at a novel NH2/ITO ion implantation modified electrode

A novel electrode was prepared by implanting NH₂ ⁺ into an ITO film (NH₂/ITO). Gold nanoparticles were deposited on the surface of NH₂/ITO electrode. The NH₂/ITO and Au/NH₂/ITO electrodes were used to determine hemoglobin (Hb) immobilized on the electrodes surfaces. The relationship of the reductive peak current value of Hb among different electrodes was: Hb/ITO:Hb/Au/ITO:Hb/NH₂/ITO:Hb/Au/NH₂/ITO=1:1.5:2:4. The linkage between the –NH₂ implanted into ITO film and the –COOH of Hb was recognized to be the reason for the increase of active Hb coverage on NH₂/ITO electrode compared with the ITO electrode. Increase of active Hb coverage on Au/NH₂/ITO compared with Au/ITO was attributed to the different amount of gold nanoparticles deposited. The determination of Hb at an Au/NH₂/ITO electrode was optimized. Calibration curve was obtained over the range of 1.0 × 10⁻⁸ – 1.0 × 10⁻⁶ mol · L⁻¹ with a detection limit of 1.0 × 10⁻⁸ mol · L⁻¹. Results showed that the novel NH₂/ITO and Au/NH₂/ITO electrodes exhibited good stability, reproducibility besides better electrochemical performance. Correspondence: Jing Bo Hu, Department of Chemistry, Beijing Normal University, Beijing 100875, China     

Ag活化的p型硅(111)表面化学镀Ag膜表面形貌研究

A method of electroless silver deposition on silver activated p-type silicon（111） wafer was proposed. The silver seed layer was deposited firstly on the wafer in the solution of 0.005 mol/L AgNO3 ＋0.06 mol/L HE Then the silver film was electrolessly deposited on the seed layer in the electroless bath of AgNO3＋NH3＋acetic acid＋NH2NH2 （pH 10.2）. The morphology of the seed layer and the silver films prepared under the condition of the different bath composition was compared by atomic force microscopy. The reflectance of the silver films with different thickness was characterized by Fourier transform infrared spectrometry. The experimental results indicate that the seed layer possesses excellent catalytic activity toward electroless silver deposition and rotating of the silicon wafer during the electroless silver deposition could lead to formation of the smoother silver film.     

Perspective on “An extended Hückel theory. I. Hydrocarbons”

 The size-consistent self-consistent matrix dressing method has been applied on an open-shell single-configuration reference state. Once the reference state is converged, several low-lying roots can be obtained for the dressed configuration interaction (CI) matrices of appropriate symmetry. The CI matrices were built with a complete-active-space singles and doubles CI method in order to deal properly with multiconfiguration excited states. The vertical ionization and ionization–excitation transitions are obtained from the difference to the closed shell ground-state energy of the neutral molecule. The method has been applied to NH⁺ ₃ and N⁺ ₂ using atomic natural orbital basis sets and state-average adapted molecular orbitals. Two ²A₁ states, very similar and showing great mixing of the (2a _l ⁻¹) and (3a _l ⁻²5a _l ¹) determinants, can be assigned to the broad asymmetric band at 27.6 ± 2 eV in the photoelectron spectrum of NH₃. The possible contribution of a ²Π _g (3σ _g ⁻²1π _g ¹) state to the A shake-up peak of N₂ at 24.6 eV is also discussed. Other states, doublets and quadruplets, are reported for both systems up to 30 eV for NH₃ and 37 eV for N₂. Received: 16 September 1999 / Accepted: 3 February 2000 / Published online: 2 May 2000     

Callus induction and plant regeneration from different explants of Actinidia deliciosa

In this study, an efficient procedure was developed for callus induction and regeneration of kiwifruit (Actinidia deliciosa) using different organs of shoots developed under in vitro conditions. Effects of explants source and media (M₁, 1.0 mg l⁻¹ BA + 2.0 mg l⁻¹ 2,4-D–M₂, 1.0 mg l⁻¹ NAA + 2.0 mg l⁻¹ 2,4-D) on initiation of callus were examined in order to obtain callus for organogenesis. The best callus for plant regeneration was obtained from leaf explants on Murashige and Skoog’s medium (MS) supplemented with M₂. Formation of callus from leaf of kiwifruit (A. deliciosa) was cultured in MS medium containing different concentration of N⁶-benzylaminopurin (BA; 0.0, 1.0, 2.0, 4.0, 6.0, 8.0 mg l⁻¹) for callus proliferation and plant regeneration. Although the first shoot formation was appeared in medium containing 6.0 and 8.0 mg l⁻¹ BA, the best shoots formation was obtained in medium with 4.0 mg l⁻¹ BA.     

Construction of a Triphenyltetrazolium Liquid Membrane Ion Selective Electrode and its Analytical Application to the Assay of Vitamin C

 The construction of a liquid triphenyltetrazolium cation (TT⁺) ion-selective electrode (ISE) based on [TT⁺]₃[P(W₃O₁₀)₄] salt dissolved in 2-nitrotoluene is described. The liquid membrane electrode exhibits a rapid and almost Nernstian response to triphenyltetrazolium cations in the concentration range from 2×10⁻⁴ to 1×10⁻² mol l⁻¹. The Nernstian slope is 56–58 mV decade⁻¹ which remains constant for at least two months. The response is virtually unaffected by pH changes in the range 3–12. Major interferents are periodate and malate. Deviation from linearity is also observed in the presence of bromide, iodide and thiocyanate, due to their precipitation with triphenyltetrazolium cations. Analytical applications such as direct potentiometry for the determination of TT⁺ in aqueous solutions and indirect potentiometry for the assay of ascorbic acid (vitamin C) in pharmaceutical preparations are described. Ascorbic acid in the range of 150–500 mg l⁻¹, under specified experimental conditions, can be determined with mean relative error of 1.9%. Received February 25, 2000. Revision April 4, 2000.     

Fabrication of TiO2/Ti nanotube electrode and the photoelectrochemical behaviors in NaCl solutions

Titanium oxide nanotube electrodes were successfully prepared by anodic oxidation on pure Ti sheets in 0.5 wt.% NH₄F + 1 wt.% (NH₄)₂SO₄ + 90 wt.% glycerol mixed solutions. Nanotubes with diameter 40–60 nm and length 7.4 μm were observed by field emission scanning electron microscope. The electrochemical and photoelectrochemical characteristics of TiO₂ nanotube electrode were investigated using linear polarization and electrochemical impedance spectroscopy techniques. The open-circuit potential dropped markedly under irradiation and with the increase of Cl⁻ concentrations. A saturated photocurrent of approximately 1.3 mA cm⁻² was observed under 10-W low-mercury lamp irradiation in 0.1 M NaCl solution, which was much higher than film electrode. Meanwhile, the highest photocurrent in NaCl solution implied that the photogenerated holes preferred to combine with Cl⁻. Thus, a significant synergetic effect on active chlorine production was observed in photoelectrocatalytic processes. Furthermore, the generation efficiency for active chlorine was about two times that using TiO₂/Ti film electrode by sol–gel method. Finally, the effects of initial pH and Cl⁻ concentration were also discussed.     

Electrochemistry at cobalt(II)tetrasulfophthalocyanine-multi-walled carbon nanotubes modified glassy carbon electrode: a sensing platform for efficient suppression of ascorbic acid in the presence of epinephrine

Electrochemistry of water-soluble cobalt(II) tetrasulfophthalocyanine (CoTSPc) electrodeposited on glassy carbon nanotube pre-modified with acid-functionalized multi-walled carbon nanotubes (MWCNT) is described. Both charge transfer resistances toward [Fe(CN)₆]^3−/4− redox probe and electrocatalytic responses toward epinephrine (EP) detection follow the trend: bare GCE < GCE-MWCNT < GCE-CoTSPc < GCE-MWCNT-CoTSPc. EP analysis was then carried out in details using GCE-MWCNT-CoTSPc. The catalytic rate constant value k _ch = 2.2 × 10⁷ (mol cm⁻³)⁻¹ s⁻¹ was obtained from rotating disk electrode experiment. Interestingly, GCE-MWCNT-CoTSPc efficiently suppressed the detection of ascorbic acid (the natural interference of neurotransmitters in physiological conditions) showing good sensitivity (0.132 ± 0.003 A l mol⁻¹), limit of detection (4.517 × 10⁻⁷ mol l⁻¹), and quantification (15.056 × 10⁻⁷ mol l⁻¹). In addition, GCE-MWCNT-CoTSPc was conveniently used to determine EP in epinephrine hydrochloric acid injection with recovery of 101.1 ± 2.2%.     

The electrochemical polymerization of <Emphasis Type="Italic">o</Emphasis>-phenylenediamine on <Emphasis Type="SmallCaps">l</Emphasis>-tyrosine functionalized glassy carbon electrode and its application

The polymerization of o-phenylenediamine (OPD) on l-tyrosine (Tyr) functionalized glassy carbon electrode (GCE) and its electro-catalytic oxidation towards ascorbic acid (AA) had been studied in this report. l-Tyrosine was first covalently grafted on GCE surface via electrochemical oxidation, which was followed by the electrochemical polymerization of OPD on the l-tyrosine functionalized GCE. Then, the poly(o-phenylenediamine)/l-tyrosine composite film modified GCE (POPD-Tyr/GCE) was obtained. X-ray photo-electron spectroscopy (XPS), field emission scanning electron microscope (SEM), and electrochemical techniques have been used to characterize the grafting of l-tyrosine and the polymerization and morphology of OPD film on GCE surface. Due to the doping of the carboxylic functionalities in l-tyrosine molecules, the POPD film showed good redox activity in neutral medium, and thus, the POPD-Tyr/GCE exhibited excellent electrocatalytic response to AA in 0.1 mol l⁻¹ phosphate buffer solution (PBS, pH 6.8). The anode peak potential of AA shifted from 0.58 V at GCE to 0.35 V at POPD-Tyr/GCE with a greatly enhanced current response. A linear calibration graph was obtained over the AA concentration range of 2.5 × 10⁻⁴–1.5 × 10^–3 mol l⁻¹ with a correlation coefficient of 0.9998. The detection limit (3δ) for AA was 9.2 × 10⁻⁵ mol l⁻¹. The modified electrode showed good stability and reproducibility and had been used for the determination of AA content in vitamin C tablet with satisfactory results.     

A kinetic study of the oxidation of <Emphasis Type="SmallCaps">l</Emphasis>-methionine by water soluble colloidal MnO<Subscript>2</Subscript>

Aqueous solution of water soluble colloidal MnO₂ was prepared by Perez-Benito method. Kinetics of l-methionine oxidation by colloidal MnO₂ in perchloric acid (0.93 × 10⁻⁴ to 3.72 × 10⁻⁴ mol dm⁻³) has been studied spectrophotometrically. The reaction follows first-order kinetics with respect to [H⁺]. The first-order kinetics with respect to l-methionine at low concentration shifts to zero order at higher concentration. The effects of [Mn(II)] and [F⁻] on the reaction rate were also determined. Manganese (II) has sigmoidal effect on the rate reaction and act as auto catalyst. The exact dependence on [Mn(II)] cannot be explained due to its oxidation by colloidal MnO₂. Methionine sulfoxide was formed as the oxidation product of l-methionine. Ammonia and carbon dioxide have not been identified as the reaction products. The mechanism with the observed kinetics has been proposed and discussed.     

Application of rapid electrothermal atomic absorption spectrometric methods to the determination of Ag, Al, Cd and Mn in cocaine and heroin samples

 Rapid methods were developed for the direct determination of Ag, Al, Cd and Mn in cocaine and heroin by ETAAS using programmes omitting the charring step . Sample pretreatment was simple: dissolution in ultrapure water or in 35.0% (v/v) HNO₃ for heroin or cocaine, respectively. Optimum drying temperatures were 250 °C for Ag, Al and Mn, and 300 °C for Cd. The run cycles were 35 and 37 s, for Ag and Al respectively, and 36 s for Cd and Mn. The best results were obtained with Pd, Mg(NO₃)₂ and (NH₄)₂HPO₄, as chemical modifiers. The limits of detection were 8.6, 55.9, 2.2 and 12.4 μg kg^-1 for Ag, Al, Cd and Mn, respectively. Received: 14 November 1996/Revised: 14 January 1997/Accepted: 18 January 1997     

Synthesis of hydrochloric acid solution for total mercury determination in natural waters

Total mercury (Hg_T) determination requires the addition of concentrated hydrochloric acid solution (≥10 mol L⁻¹ HCl) in relatively high amounts to preserve the samples and to prepare reagent solutions. A method for the preparation of concentrated HCl with Hg_T concentration of lower than 5 ng L⁻¹ is described in this article. It is based on the well-known chemical reaction: 2 NH₄Cl + H₂SO₄ → (NH₄)₂SO₄ + 2 HCl. This method is validated thanks to the US Environmental Protection Agency method 1631 and standard reference materials BCR-579 (mercury in coastal seawater).     

Electrogeneration of polyluminol and chemiluminescence for new disposable reagentless optical sensors

A performant reagentless electrochemiluminescent (ECL) detection system for H₂O₂ is presented, based on an electropolymerized polyluminol film prepared under near-neutral conditions. Such an original polyluminol electrodeposition is reported for the first time and on a screen-printed electrode (SPE) surface. Electropolymerized luminol acts as an active luminophore of the electrochemiluminescent reaction, as the monomer does. Polymerization conditions have been optimized in order to obtain the best ECL responses to H₂O₂. By performing electrodeposition in a potentiostatic mode, at 425 mV vs. Ag|AgCl, in 0.1 mol L⁻¹ phosphate/0.1 mol L⁻¹ KCl pH 6 and 1 mmol L⁻¹ luminol, with a total charge of 0.5 mC, the linear range for H₂O₂ detection extends from 7.9 × 10⁻⁸ mol L⁻¹ to 1.3 × 10⁻³ mol L⁻¹. Such performant disposable reagentless easy-to-use miniaturized systems based on SPEs should be applicable to the electrochemiluminescent detection of many oxidase-substrate compounds. Figure An original polyluminol electrodeposition process on a screen-printed electrode surface is reported for the first time. The polymeric structure is demonstrated to behave as an electrochemiluminescent luminophore, allowing disposable reagentless easy-to-use optical sensors for hydrogen peroxide detection to be designed.     

Recovery of palladium from spent solutions for manufacture of catalysts

Palladium recovery from [Pd(NH₃)₄]Cl₂ solutions (concentration in terms of the metal ∼1 g l⁻¹) with flow-through porous electrodes was studied. The conditions of effective electrochemical recovery of Pd were found. Various porous cathodes were compared.     

Polarographic Catalytic Wave of Prednisone in the Presence of Persulfate and its Application

 A polarographic catalytic wave of prednisone in the presence of K₂S₂O₈ was observed. The polarographic catalytic wave of prednisone as catalyst was attributed to such chemical reaction parallel to electrode reaction as oxidized the free radical from one electron reduction of the Δ^1,4-3 keto group of prednisone to regenerate the original keto group. The catalytic wave can be used for the determination of prednisone with the help of conventional polarographic equipment, such as linear-potential scan polarograph. In 0.12 mol l⁻¹ HAc-0.08 mol l⁻¹ NaAc-0.014 mol l⁻¹ K₂S₂O₈ (pH 4.6) supporting electrolyte, the second-order derivative peak current of the catalytic wave was rectilinear to prednisone concentration in the range of 3.2 × 10⁻⁷∼1.6 × 10⁻⁵ mol l⁻¹. The detection limit was 8.0 × 10⁻⁸ mol l⁻¹. Received August 6, 2001; accepted April 17, 2002; published online July 22, 2002     

Electrocatalytic determination of reduced glutathione in human erythrocytes

The determination of reduced glutathione (GSH) in human erythrocytes using a simple, fast and sensitive method employing a glassy carbon electrode modified with cobalt tetrasulfonated phthalocyanine (CoTSPc) immobilized in poly(l-lysine) (PLL) film was investigated. This modified electrode showed very efficient electrocatalytic activity for anodic oxidation of GSH, decreasing substantially the anodic overpotentials for 0.2 V versus Ag/AgCl. The modified electrode presented better performance in 0.1 mol l⁻¹ piperazine-N,N′-bis(2-ethanesulfonic acid) buffer at pH 7.4. The other experimental parameters, such as the concentration of CoTSPc and PLL in the membrane preparation, pH, type of buffer solution and applied potential, were optimized. Under optimized operational conditions, a linear response from 50 to 2,160 nmol l⁻¹ was obtained with a high sensitivity of 1.5 nA l nmol⁻¹ cm⁻². The detection limit for GSH determination was 15 nmol l⁻¹. The proposed sensor presented good repeatability, evaluated in terms of the relative standard deviation (1.5%) for n = 10. The modified electrode was applied for determination of GSH in erythrocyte samples and the results were in agreement with those obtained by a comparative method described in the literature The average recovery for these fortified samples was 100 ± 1)%. Applying a paired Student’s-t test to compare these methods, we could observe that, at the 95% confidence level, there was no statistical difference between the reference and the proposed methods.     

Composite films of polyaniline and molybdenum oxide formed by electrocodeposition in aqueous media

Composite films of polyaniline (PANI) and molybdenum oxide (MoO_x) were afforded through a convenient route of electrocodeposition from aniline and (NH₄)₆Mo₇O₂₄. The composite films showed characteristic redox behaviors of PANI and MoO_x, respectively, on the cyclic voltammograms. Chlorate and bromate were catalytically electroreduced with an enlarged current on the composite film at a potential ca. 0.2 V more positive than that on MoO_x. The potential window for the composite film to display pseudocapacitive properties in 1.0 mol·dm⁻³ NaNO₃ was −0.6 ∼ 0.6 V vs SCE. The cathodic potential limit shifted at least 0.4 V negatively from that of polyaniline (PANI)-based materials reported so far. The specific capacitance was 363.6 F·g⁻¹ when the composite film was charged–discharged at 1.5 mA·cm⁻², about two times of that of the similarly prepared PANI. The composite film was characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Molybdenum existed in a mixed state of +5 and +6 in the composite film based on XRD and XPS investigations. Figure PANI and (MoO_x) were electrocodeposited in aqueous solutions from aniline and (NH₄)₆Mo₇O₂₄. The composite film obtained displayed catalytic activities toward the electroreduction of oxoanions. The pseudocapacitance of the composite film is nearly two times of that of PANI with the potential window extended negatively up to −0.6 V vs SCE     

RISM-SCF study of the free-energy profile of the Menshutkin-type reaction NH3+CH3Cl→NH3CH3++Cl− in aqueous solution

The free-energy profile for the Menshutkin-type reaction NH₃ + CH₃Cl → NH₃CH₃ ⁺ + Cl⁻ in aqueous solution is studied using the RISM-SCF method. The effect of electron correlation on the free-energy profile is estimated by the RISM-MP2 method at the HF optimized geometries along the reaction coordinate. Solvation was found to have a large influence on the vibrational frequencies at the reactant, transition state and product; these vibrational frequencies are utilized to calculate the zero-point energy correction of the free-energy profile. The computed barrier height and reaction exothermicity are in reasonable agreement with those of experiment and previous calculations. The change of solvation structure along the reaction path is represented by radial distribution functions between solute-solvent atomic sites. The mechanisms of the reaction are discussed from the view points of solute electronic and solvation structures. Received: 26 June 1998/Accepted: 28 August 1998 / Published online: 2 November 1998     

Theoretical studies on the structure of M+BF−4 ion pairs M = Li+, NH+4: the role of electrostatics and electron correlation

A systematic investigation of the M⁺BF₄ ⁻ (M = Li or NH₄) ion-pair conformers has been carried out using an electrostatic docking model based on the molecular electrostatic potential topography of the free anion. This method provides a guideline for the subsequent ab initio molecular orbital calculations at the Hartree-Fock (HF) and second-order M?ller-Plesset perturbation theory (MP2) levels. It has been demonstrated that the model presented here yields more than 75% of the HF interaction energy when Li⁺ is the cation involved and more than 90% for the case of NH₄ ⁺. Inclusion of MP2 correlation in the HF-optimized geometries leads to stationary point geometries with different numbers of imaginary frequencies and in some places where the energies of two adjacent conformers are very close, the energy rank order is altered. The HF lowest-energy minima for the Li⁺BF₄ ⁻ and NH₄ ⁺BF₄ ⁻ show a bidentate and tridentate coordinating cation, respectively, whereas at the MP2 level, this ordering is reversed. Received: 9 September 1997 / Accepted: 5 November 1997     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.