Quantification of butanol and ethanol in aqueous phases by reflectometric interference spectroscopy--different approaches to multivariate calibration

This paper presents several methods for analysis of data from reflectometric interference spectroscopic measurements (RIfS) of water samples. The set-up consists of three sensors with different polymer layers. Mixtures of butanol and ethanol in water were measured from 0 to 12,000 ppm each. The data space was characterized by principal component analysis (PCA). Calibration and prediction were achieved by multivariate methods, e.g. multiple linear regression (MLR), partial least squares (PLS) with additional predictors, and quadratic partial least squares (Q-PLS), and by use of artificial neural networks. Artificial neural networks gave the best results of all the calibration methods used. Calibration and prediction of the concentration of the two analytes by artificial neural nets were robust and the set-up could be reduced to only two sensors without deterioration of the prediction.     

A comparative study of laser induced breakdown spectroscopy analysis for element concentrations in aluminum alloy using artificial neural networks and calibration methods

A comparative study of analysis methods (traditional calibration method and artificial neural networks (ANN) prediction method) for laser induced breakdown spectroscopy (LIBS) data of different Al alloy samples was performed. In the calibration method, the intensity of the analyte lines obtained from different samples are plotted against their concentration to form calibration curves for different elements from which the concentrations of unknown elements were deduced by comparing its LIBS signal with the calibration curves. Using ANN, an artificial neural network model is trained with a set of input data of known composition samples. The trained neural network is then used to predict the elemental concentration from the test spectra. The present results reveal that artificial neural networks are capable of predicting values better than traditional method in most cases.     

Determination of amylose content in starch using Raman spectroscopy and multivariate calibration analysis

Fourier transform Raman spectroscopy and chemometric tools have been used for exploratory analysis of pure corn and cassava starch samples and mixtures of both starches, as well as for the quantification of amylose content in corn and cassava starch samples. The exploratory analysis using principal component analysis shows that two natural groups of similar samples can be obtained, according to the amylose content, and consequently the botanical origins. The Raman band at 480 cm^?1, assigned to the ring vibration of starches, has the major contribution to the separation of the corn and cassava starch samples. This region was used as a marker to identify the presence of starch in different samples, as well as to characterize amylose and amylopectin. Two calibration models were developed based on partial least squares regression involving pure corn and cassava, and a third model with both starch samples was also built; the results were compared with the results of the standard colorimetric method. The samples were separated into two groups of calibration and validation by employing the Kennard-Stone algorithm and the optimum number of latent variables was chosen by the root mean square error of cross-validation obtained from the calibration set by internal validation (leave one out). The performance of each model was evaluated by the root mean square errors of calibration and prediction, and the results obtained indicate that Fourier transform Raman spectroscopy can be used for rapid determination of apparent amylose in starch samples with prediction errors similar to those of the standard method.

An Analysis of Mixtures Using Amperometric Biosensors and Artificial Neural Networks

This paper presents a sensor system based on a combination of an amperometric biosensor acting in batch as well as flow injection analysis with the chemometric data analysis of biosensor outputs. The multivariate calibration of the biosensor signal was performed using artificial neural networks. Large amounts of biosensor calibration as well as test data were synthesized using computer simulation. Mathematical and corresponding numerical models of amperometric biosensors have been built to simulate the biosensor response to mixtures of compounds. The mathematical model is based on diffusion equations containing a non-linear term related to Michaelis–Menten kinetics of the enzymatic reaction. The principal component analysis was applied for an optimization of calibration data. Artificial neural networks were used to discriminate compounds of mixtures and to estimate the concentration of each compound. The proposed approach showed prediction of each component with recoveries greater that 99% in flow injection as well as in batch analysis when the biosensor response is under diffusion control.     

Determination of water in lubricating oils by mid- and near-infrared spectroscopy

Mid-infrared (MIR) and near-infrared (NIR) spectroscopy were used to determine water in lubricating oils with high additive contents that introduce large errors in determinations by the Karl-Fischer and hydride methods. MIR spectra were obtained in the attenuated total reflectance (ATR) mode and exhibited water specific band absorption in the region 3100–3700cm^–1, which facilitated calibration. Multivariate (partial least-squares regression, PLSR) and univariate calibration (based on peak height and band area as independent variables) were tested. Both led to errors of prediction less than 5%. NIRS determinations rely on absorbance and first-derivative spectra, in addition to two different types of multivariate calibration,viz. inverse multiple linear regression (MLR) and partial least-squares regression (PLSR). Both approaches gave similar results, with errors of prediction less than 2%.For none of the proposed approaches any sample pretreatment for recording spectra is required.     

Quantification of butanol and ethanol in aqueous phases by reflectometric interference spectroscopy – different approaches to multivariate calibration

This paper presents several methods for analysis of data from reflectometric interference spectroscopic measurements (RIfS) of water samples. The set-up consists of three sensors with different polymer layers. Mixtures of butanol and ethanol in water were measured from 0 to 12,000 ppm each. The data space was characterized by principal component analysis (PCA). Calibration and prediction were achieved by multivariate methods, e.g. multiple linear regression (MLR), partial least squares (PLS) with additional predictors, and quadratic partial least squares (Q-PLS), and by use of artificial neural networks. Artificial neural networks gave the best results of all the calibration methods used. Calibration and prediction of the concentration of the two analytes by artificial neural nets were robust and the set-up could be reduced to only two sensors without deterioration of the prediction. Received: 29 September 2000 / Revised: 30 April 2001 / Accepted: 3 May 2001     

Determination of acetonitrile and ethanol in water by guided microwave spectroscopy with multivariate calibration

The feasibility of using guided microwave spectroscopy (GMS) utilizing the frequency range 0.25-3.20 GHz, was combined with multivariate calibration for the determination of acetonitrile or ethanol concentration in water. A wide range of different concentrations was used (up to 30% v/v). Partial least squares (PLS) and weighted ridge regression (WRR) was applied to generate a model for prediction, based upon the microwave spectra. A high level of collinearity was observed in both of the sample data sets and this was reduced by background subtraction. The prediction ability for the two types of regression models were found to be comparable with the percentage error of prediction (PEP) being approximately 2.5% for the acetonitrile samples and 1.1% for ethanol samples.     

Combining convolutional neural networks and in‐line near‐infrared spectroscopy for real‐time monitoring of the chromatographic elution process in commercial production of notoginseng total saponins

The chromatographic elution process is a key step in the production of notoginseng total saponins. Due to quality variability of loading samples and resin capacity decreasing over cycle time, saponins, especially the five main saponins of notoginseng total saponins, need to be monitored in real time during the elution process. In this study, convolutional neural networks, one of the most popular deep learning methods, were used to develop quantitative calibration models based on in‐line near‐infrared spectroscopy for notoginsenoside R₁, ginsenosides Rg₁, Re, Rb₁ and Rd, and their sum concentration, with root mean square error of prediction values of 0.87, 2.76, 0.60, 1.57, 0.28, and 4.99 mg/mL, respectively. Partial least squares calibration models were also developed for model performance comparison. Results show predicted concentration profiles outputted by both the convolutional neural network models and partial least squares models show agreements with the real trends defined by reference measurements, and can be used for elution process monitoring and endpoint determination. To the best of our knowledge, this is the first reported case study of combining convolutional neural networks and in‐line near‐infrared spectroscopy for monitoring of the chromatographic elution process in commercial production of botanical drug products.     

径向基函数网络在近红外人体无创伤血糖浓度检测基础研究中的应用

在近红外无创伤血糖浓度检测的基础研究中，对于多组分的混合物的分析，常因光谱与样品浓度之间呈现非线性响应，使得基于线性模型的校正方法失效。本文讨论了非线性校正方法径向基函数神经网络( RBFN )的有效性，并与线性校正方法中的主成分分析和偏最小二乘法作了对比研究。验证实验所用样品为①葡萄糖水溶液②包含牛血红蛋白和白蛋白的葡萄糖水溶液，结果表明：在①实验中PLS模型和RBFN预测标准偏差分别为8．2、8．9；在②实验中分别为15．6、8．8。可见在样品组分增多时，RBFN算法较线性PLS方法建立的模型预测能力强。     

Application of a Partial Least Squares Regression for the Determination of Nanomolar Concentrations of Scandium in the Presence of Nickel by Adsorptive Stripping Voltammetry

This paper presents the methodology of a very sensitive determination of scandium in excess of nickel by adsorptive stripping voltammetry on a mercury film electrode and PLS regression. A calibration set consisting of binary mixtures containing 5, 15, 25, 35 or 45×10^?9 M Sc(III) and simultaneously 0.5–50×10^?7 M of Ni(II) was used to develop the chemometric PLS calibrations. An external set containing synthetic mixtures of 10, 20, 30, 40×10^?9 M Sc(III) and the same Ni(II) concentration as mentioned above was used to validate the model and evaluate predictive ability. The application of data pretreatment techniques involving baseline correction, smoothing, range‐scaling, mean‐centering and their influence on the PLS model complexity, were also investigated. In the effect, the model for Sc(III), including 6 latent variables, was constructed. The model fulfills validation criteria and is characterized by a good prediction ability (majority of the prediction errors are lower than 10%). This work shows significant progress in the development of a very sensitive analytical technique for the determination of scandium in the presence of different concentrations of nickel by application of multivariate calibration tools.     

Development of a univariate calibration model for pharmaceutical analysis based on NIR spectra

Near-infrared spectroscopy (NIRS) has been widely used in the pharmaceutical field because of its ability to provide quality information about drugs in near-real time. In practice, however, the NIRS technique requires construction of multivariate models in order to correct collinearity and the typically poor selectivity of NIR spectra. In this work, a new methodology for constructing simple NIR calibration models has been developed, based on the spectrum for the target analyte (usually the active principle ingredient, API), which is compared with that of the sample in order to calculate a correlation coefficient. To this end, calibration samples are prepared spanning an adequate concentration range for the API and their spectra are recorded. The model thus obtained by relating the correlation coefficient to the sample concentration is subjected to least-squares regression. The API concentration in validation samples is predicted by interpolating their correlation coefficients in the straight calibration line previously obtained. The proposed method affords quantitation of API in pharmaceuticals undergoing physical changes during their production process (e.g. granulates, and coated and non-coated tablets). The results obtained with the proposed methodology, based on correlation coefficients, were compared with the predictions of PLS1 calibration models, with which a different model is required for each type of sample. Error values lower than 1-2% were obtained in the analysis of three types of sample using the same model; these errors are similar to those obtained by applying three PLS models for granules, and non-coated and coated samples. Based on the outcome, our methodology is a straightforward choice for constructing calibration models affording expeditious prediction of new samples with varying physical properties. This makes it an effective alternative to multivariate calibration, which requires use of a different model for each type of sample, depending on its physical presentation.     

Spectrophotometric simultaneous determination of ceratine, creatinine, and uric acid in real samples by orthogonal signal correction–partial least squares regression

Abstract  This work describes a quantitative spectroscopic method for the analysis of ternary mixtures of ceratine (CER), creatinine (CRE), and uric acid (UA) using multivariate data models based upon ultraviolet spectroscopy. By multivariate calibration methods, such as partial least squares regression, it is possible to obtain a model adjusted to the concentration values of the mixtures used in the calibration range. In this study, the calibration model is based on absorption spectra in the 200–260 nm range for 36 different mixtures of CER, CRE, and UA. The unrelated information was removed by the orthogonal signal correction (OSC) method and the results were proved. Evaluation of the prediction errors for the prediction set reveals the OSC-treated data give substantially lower root mean square error of prediction (RMSEP) values than original data. The RMSEP for CER, CRE, and UA with OSC were 1.1686, 0.2195, and 0.3726, and without OSC were 1.9057, 0.3482, and 0.6164, respectively. This procedure allows the simultaneous determination of CER, CRE, and UA in synthetic and real samples. Graphical abstract        

Chemometric determination of arsenic and lead in untreated powdered red paprika by diffuse reflectance near-infrared spectroscopy

It has been evaluated the potential of near-infrared (NIR) diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) as a way for non-destructive measurement of trace elements at μg kg⁻¹ level in foods, with neither physical nor chemical pre-treatment. Predictive models were developed using partial least-square (PLS) multivariate approaches based on first-order derivative spectra. A critical comparison of two spectral pre-treatments, multiplicative signal correction (MSC) and standard normal variate (SNV) was also made. The PLS models built after using SNV provided the best prediction results for the determination of arsenic and lead in powdered red paprika samples. Relative root-mean-square error of prediction (RRMSEP) of 23% for both metals, arsenic and lead, were found in this study using 20 well characterized samples for calibration and 13 additional samples as validation set. Results derived from this study showed that NIR diffuse reflectance spectroscopy combined with the appropriate chemometric tools could be considered as an useful screening tool for a rapid determination of As and Pb at concentration level of the order of hundred μg kg⁻¹.     

Quantitative determination of acyclovir in plasma by near infrared spectroscopy

The aim of this study was to assess the feasibility of near infrared spectroscopy (NIRS) for analysis of acyclovir in plasma. This methodology was based on the direct measurement of the transmission spectra of liquid samples and a multivariate calibration model (partial least squares, PLS) to determine the acyclovir concentration in plasma sample. The PLS calibration set was built on using the spiked samples by mixing different amounts of acyclovir. Concentration of acyclovir in the plasma samples was calculated employing a 6-factors PLS calibration using the spectral information in the range of 6102-5450 cm^− 1. The root mean square errors of prediction (RMSEP) found was 1.21 for acyclovir. The developed PLS-NIRS procedure allows the determination of 120 samples/h does not require any sample pretreatment and avoids waste generation.     

Nondestructive determination of compound amoxicillin powder by NIR spectroscopy with the aid of chemometrics

Near-infrared (NIR) spectroscopy, in combination with chemometrics, enables nondestructive analysis of solid samples without time-consuming sample preparation methods. A new method for the nondestructive determination of compound amoxicillin powder drug via NIR spectroscopy combined with an improved neural network model based on principal component analysis (PCA) and radial basis function (RBF) neural networks is investigated. The PCA technique is applied to extraction relevant features from lots of spectra data in order to reduce the input variables of the RBF neural networks. Various optimum principal component analysis-radial basis function (PCA-RBF) network models based on conventional spectra and preprocessing spectra (standard normal variate (SNV) and multiplicative scatter correction (MSC)) have been established and compared. Principal component regression (PCR) and partial least squares (PLS) multivariate calibrations are also used, which are compared with PCA-RBF neural networks. Experiment results show that the proposed PCA-RBF method is more efficient than PCR and PLS multivariate calibrations. And the PCA-RBF approach with SNV preprocessing spectra is found to provide the best performance.     

Quantitative Near-infrared Spectroscopic Analysis of Trimethoprim by Artificial Neural Networks Combined with Modified Genetic Algorithm

A novel method for rapid,accurate and nondestructive determination of trimethoprim in complex matrix was presented.Near-infrared spectroscopy coupled with multivariate calibration（partial least-squares and artificial neural networks） was applied in the experiment.The variable selection process based on a modified genetic algorithm with fixed number of selected variables was proceeded,which can reduce the training time and enhance the predictive ability when coupled with artificial neural network model.     

偏最小二乘线性拟合滴定甘蔗糖蜜中多组分有机酸

将滴定体系调节至pH 2.0,用碱标准溶液滴定至特定pH所消耗滴定荆为测量指标,构建了多组分有机酸滴定数据阵,分别以主成分回归法、偏最小二乘法以及人工神经元网络法进行多组分拟合.结果表明,偏最小二乘法的拟合结果最佳,对混合体系中乙酸、乳酸、草酸、琥珀酸、柠檬酸和乌头酸总量的相对预测均方根误差分别为5.80%、8.88%...     

Partial least square analysis of lysozyme near-infrared spectra

Proteins possess strong absorption features in the combination range (5000-4000 cm⁻¹) of the near infrared (NIR) spectrum. These features can be used for quantitative analysis. Partial least squares (PLS) regression was used to analyze NIR spectra of lysozyme with the leave-one-out, full cross-validation method. A strategy for spectral range optimization with cross-validation PLS calibration was presented. A five-factor PLS model based on the spectral range between 4720 and 4540 cm⁻¹ provided the best calibration model for lysozyme in aqueous solutions. For 47 samples ranging from 0.01 to 10 mg/mL, the root mean square error of prediction was 0.076 mg/mL. This result was compared with values reported in the literature for protein measurements by NIR absorption spectroscopy in human serum and animal cell culture supernatants.     

Quantification of Corn Adulteration in Wet and Dry-Processed Peaberry Ground Roasted Coffees by UV–Vis Spectroscopy and Chemometrics

In this present research, a spectroscopic method based on UV–Vis spectroscopy is utilized to quantify the level of corn adulteration in peaberry ground roasted coffee by chemometrics. Peaberry coffee with two types of bean processing of wet and dry-processed methods was used and intentionally adulterated by corn with a 10–50% level of adulteration. UV–Vis spectral data are obtained for aqueous samples in the range between 250 and 400 nm with a 1 nm interval. Three multivariate regression methods, including partial least squares regression (PLSR), multiple linear regression (MLR), and principal component regression (PCR), are used to predict the level of corn adulteration. The result shows that all individual regression models using individual wet and dry samples are better than that of global regression models using combined wet and dry samples. The best calibration model for individual wet and dry and combined samples is obtained for the PLSR model with a coefficient of determination in the range of 0.83–0.93 and RMSE below 6% (w/w) for calibration and validation. However, the error prediction in terms of RMSEP and bias were highly increased when the individual regression model was used to predict the level of corn adulteration with differences in the bean processing method. The obtained results demonstrate that the use of the global PLSR model is better in predicting the level of corn adulteration. The error prediction for this global model is acceptable with low RMSEP and bias for both individual and combined prediction samples. The obtained RPD_p and RER_p in prediction for the global PLSR model are more than two and five for individual and combined samples, respectively. The proposed method using UV–Vis spectroscopy with a global PLSR model can be applied to quantify the level of corn adulteration in peaberry ground roasted coffee with different bean processing methods.     

Simultaneous determination of albumin and immunoglobulin G with fluorescence spectroscopy and multivariate calibration

A method is proposed for the simultaneous determination of albumin and immunoglobulin G (IgG1) with fluorescence spectroscopy and multivariate calibration with partial least squares regression (PLS). The influence of some instrumental parameters were investigated with two experimental designs comprising 19 and 11 experiments, respectively. The investigated parameters were excitation and emission slit, detection voltage and scan rate. When a suitable instrumental setting had been found, a minor calibration and test set were analysed and evaluated. Thereafter, a larger calibration of albumin and IgG1 was made out of 26 samples (0-42 μg ml⁻¹ albumin and 0-12.7 μg ml⁻¹ IgG1). This calibration was validated with a test set consisting of 14 samples in the same concentration range. The precision of the method was estimated by analysing two test set samples for six times each. The scan modes tested were emission scan and synchronous scan Δ60 nm. The results showed that the method could be used for determination of albumin and IgG1 (albumin, root mean square error of prediction (RMSEP) <2, relative standard error of prediction (RSEP) <6% and IgG1, RMSEP <1, RSEP <8%) in spite of the overlapping fluorescence of the two compounds. The estimated precision was relative standard deviation (R.S.D.) <1.7%. The method was finally applied for the analysis of some sample fractions from an albumin standard used in affinity chromatography.