核壳结构的Co3O4@δ-MnO2/Pt作为锂氧电池高效催化正极

通过简易、可控的水热方法在泡沫镍基体上直接生长了核壳结构的阵列型Co₃O₄@δ-MnO₂/Pt正极。阵列电极有利于电极的润湿、氧气的传输和Li₂O₂的负载。Co₃O₄@δ-MnO₂/Pt正极对氧还原和氧析出反应具有高的催化性能,可促使Li₂O₂依附Co₃O₄@δ-MnO₂/Pt阵列生长,从而保持阵列结构。该生长行为有利于Li₂O₂在充电时分解。以Co₃O₄@δ-MnO₂/Pt为催化正极的锂氧电池显示出高的容量（在电流密度100 mA·g^-1时容量为2 480 mAh·g^-1）,以及长的循环寿命（容量限定在500 mAh·g^-1时,在200 mA·g^-1电流密度下,可循环65次）,该性能超过了使用Co₃O₄或Co₃O₄@δ-MnO₂催化剂的电池。     

Co3O4纳米片的制备及其电化学电容性能

以配位超分子化合物为前驱物,通过液相氧化分解得到了六方形CoOOH纳米片,进而在空气中热处理制得了Co₃O₄纳米片。利用XRD、TEM、FESEM对CoOOH和Co₃O₄纳米片的结构和形貌进行了表征。电化学测试表明,Co₃O₄纳米片电极在6 mol·L^-1 KOH溶液中表现出良好的电化学电容特性,在电流密度为1 A·g^-1其单电极比容量可达到227 F·g^-1。     

层状正极材料LiNi0.5Co0.25Mn0.25O2的结构及电化学行为

采用溶胶-凝胶方法制备了正极材料LiNi_0.5Co_0.25Mn_0.25O₂。XRD、XPS测试结果表明：LiNi_0.5Co_0.25Mn_0.25O₂中阳离子排列有序度较高，层状结构明显；Co、Mn分别以+3、+4价形式存在，Ni以+2、+3价形式存在，且Ni²⁺与Ni³⁺的含量之比约为1∶1。SEM测试结果表明：正极材料LiNi_0.5Co_0.25Mn_0.25O₂结晶粒径较均匀。充放电测试结果表明：与LiCoO₂相比，尽管LiNi_0.5Co_0.25Mn_0.25O₂的放电电压平台较低，但放电容量较高；在恒流充电模式下，当充电截止电压由4.35 V升高至4.75 V时，首次放电容量由179 mAh·g^-1增至201 mAh·g^-1，50次循环后，容量保持率由74.95%增至78.48%；在先恒流再恒压的充电模式下，电池首次放电容量为212 mAh·g^-1，50次循环后，容量保持率提高到87.71%。循环伏安测试表明：在2.80～4.80 V扫描范围内，该正极材料发生Ni²⁺/Ni³⁺，Co³⁺/Co⁴⁺两对电化学反应。EIS测试表明：随着充电截止电压的增大，该正极材料的传荷电阻变小。     

多层多孔Co3O4纳米粒子组装体的合成、表征和电化学性能研究

利用十二烷基磺酸钠(SDS)作为表面活性剂,合成了形貌化的CoC₂O₄配合物前驱物,然后在500 ℃下热分解形貌化的前驱物,得到了多层多孔Co₃O₄纳米粒子组装体。采用FESEM、TEM、HRTEM、XRD、N₂吸附脱附和Raman散射等手段对产物进行了分析和表征。低角XRD,TEM和N₂吸附脱附测试表明所得组装体具有多孔结构。常规XRD、HRTEM和Raman结果证明组装体中Co₃O₄纳米粒子建筑块结晶较好。与体相Co₃O₄晶体相比,Co₃O₄纳米粒子组装体的5个拉曼活性峰发生了明显的红移。将Co₃O₄纳米粒子组装体作为锂离子电池的正极材料进行了电化学性能测试,结果表明该组装体电极的首次放电容量为1 115 mAh·g^-1,远高于目前文献报道的Co₃O₄纳米管、纳米粒子和纳米棒电极。但是,该组装体电极的循环性能不好,有待进一步提高。     

尖晶石型LiMn2O4的制备及超级电容性能研究

采用高温固相法制备LiMn₂O₄。X射线衍射结果表明800 ℃下得到尖晶石型LiMn₂O₄。利用恒流充放电、循环伏安和交流阻抗等研究了LiMn₂O₄电极材料在2 mol·L^-1 (NH₄)₂SO₄溶液中的超级电容性能。循环伏安测试结果表明LiMn₂O₄电极材料在0～1 V电位窗口范围内具有较好的方形特征；恒流充放电结果表明充放电曲线呈现出较规整的三角形对称分布，放电曲线呈直线关系，5 mA·cm^-2下的放电比容量为141 F·g^-1，具有较高的充放电效率，循环性能稳定；交流阻抗结果也显示LiMn₂O₄电极材料在2 mol·L^-1 (NH₄)₂SO₄中具有典型的电容阻抗特性。     

Mn4+掺杂Co3O4纳米纤维的静电纺丝法制备及其电化学性能

通过静电纺丝法制备Mn⁴⁺掺杂的Co₃O₄复合纳米纤维,利用XRD、XPS、BET、SEM和电化学工作站等对材料的结构、成分、形貌和电化学性能进行表征与测试。研究发现,通过Mn⁴⁺掺杂,Co₃O₄复合纳米纤维的电化学性能得到明显改善。当n_Co∶n_Mn=20∶2时,相应的复合纤维具有较大比表面积68 m²·g^-1,而且该样品呈现出清晰的氧化还原峰,在1 A·g^-1的电流密度下,放电比电容量为585 F·g^-1,这比纯Co₃O₄纳米纤维的416 F·g^-1,有显著提高;循环500圈电容保持率达到82.6%,而纯Co₃O₄纳米纤维则是76.4%。     

Co3O4/ZnO修饰针灸针的制备及其在葡萄糖检测领域的应用

将Co₃O₄/ZnO针状纳米棒材料修饰到针灸针表面用于检测葡萄糖浓度的变化。首先采用水热法在针灸针表面得到 Co（CO₃）_0.5（OH）·0.11H₂O针状纳米棒前驱体,然后在500 ℃条件下退火3 h得到Co₃O₄针状纳米棒阵列。再采用浸渍法将预制备好的ZnO量子点修饰到Co₃O₄针状纳米棒表面,得到Co₃O₄/ZnO复合修饰的针灸针。研究发现此针灸针对葡萄糖具有较好的电流响应（2 264.27 μA·L·mmol^-1·cm^-2）、较快的响应速度（<4 s）及较低的检测极限（0.311 μmol·L^-1（S/N=3））。且该针灸针在用于检测人体模拟细胞液中葡萄糖浓度时,对抗坏血酸和尿素等表现出较强的抗干扰性。     

溶剂热法合成纳米立方状Co3O4及其电容特性研究

以聚乙二醇为分散剂，在水-正丁醇体系中采用溶剂热法合成纳米立方状Co₃O₄。采用IR、XRD和TEM等手段对前驱物及产物的物相和形貌进行表征，对溶剂热法合成Co₃O₄的反应机理进行初步研究，并以Scherrer公式计算出样品平均晶粒尺寸为21.6 nm。通过循环伏安、恒流充放电、交流阻抗等测试对Co₃O₄电极的电化学性能进行表征。结果表明，在2 mol·L^{-1相似文献}   

Co3O4/ZnO修饰针灸针的制备及其在葡萄糖检测领域的应用

将Co₃O₄/ZnO针状纳米棒材料修饰到针灸针表面用于检测葡萄糖浓度的变化。首先采用水热法在针灸针表面得到Co（CO₃）_0.5（OH）·0.11H₂O针状纳米棒前驱体,然后在500 ℃条件下退火3 h得到Co₃O₄针状纳米棒阵列。再采用浸渍法将预制备好的ZnO量子点修饰到Co₃O₄针状纳米棒表面,得到Co₃O₄/ZnO复合修饰的针灸针。研究发现此针灸针对葡萄糖具有较好的电流响应（2 264.27 μA·L·mmol^-1·cm^-2）、较快的响应速度（<4 s）及较低的检测极限（0.311 μmol·L^-1（S/N=3））。且该针灸针在用于检测人体模拟细胞液中葡萄糖浓度时,对抗坏血酸和尿素等表现出较强的抗干扰性。     

不同形貌Co3O4的制备及其活化过一硫酸盐降解亚甲基蓝的性能

分别采用尿素水热-煅烧法、化学浴沉积-煅烧法和草酸盐热解法制备出具有不同形貌的Co₃O₄（Co₃O₄-A、Co₃O₄-B和Co₃O₄-C） 粉体材料,对比了它们作为催化剂活化过一硫酸盐（PMS）降解亚甲基蓝（MB）的性能。结果表明,3种Co₃O₄材料均具有分级微/纳米结构,形貌分别呈绒球状、无规则颗粒状和纤维状。PMS在3种催化剂作用下的分解过程均符合一级反应动力学模型,反应速率常数依次为0.047 1、0.217 4和0.003 7 min^-1。无规则颗粒状Co₃O₄-B表现出最高的PMS活化性能,是其具有最大比表面积、最高表面氧空位浓度以及表面羟基密度综合作用的结果。在催化剂用量0.02 g·L^-1、PMS投加量0.6 mmol·L^-1的工艺参数条件下,Co₃O₄-B/PMS高级氧化体系在25 min内对MB的降解即可达98.33%。电子顺磁共振测试证实Co₃O₄-B/PMS高级氧化体系中存在·SO₄^-、·OH、·O₂^-和¹O₂四种活性氧物种,基于此提出了Co₃O₄-B活化PMS及降解MB的反应机理。     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

A new 2212-type stair like structure: Bi14Sr21Fe12O61, m=5 member of the generic [Bi2Sr3Fe2O9]m[Bi4Sr6Fe2O16] family

A new oxide, Bi₁₄Sr₂₁Fe₁₂O_61, with a layered structure derived from the 2212 modulated type structure Bi₂Sr₃Fe₂O₉, was isolated. It crystallizes in the I2 space group, with the following parameters: a=16.58(3) Å, b=5.496(1) Å, c=35.27(2) Å and β=90.62°. The single crystal X-ray structure determination, coupled with electron microscopy, shows that this ferrite is the m=5 member of the [Bi₂Sr₃Fe₂O₉]_m[Bi₄Sr₆Fe₂O₁₆] collapsed family. This new collapsed structure can be described as slices of 2212 structure of five bismuth polyhedra thick along , shifted with respect to each other and interconnected by means of [Bi₄Sr₆Fe₂O₁₆] slices. The latter are the place of numerous defects like iron or strontium for bismuth substitution; they can be correlated to intergrowth defects with other members of the family.     

Synthesis, crystal structure, infrared and Raman spectra of Sr4Cu3(AsO4)2(AsO3OH)4·3H2O and Ba2Cu4(AsO4)2(AsO3OH)3

The two new compounds, Sr₄Cu₃(AsO₄)₂(AsO₃OH)₄·3H₂O (1) and Ba₂Cu₄(AsO₄)₂(AsO₃OH)₃(2), were synthesized under hydrothermal conditions. They represent previously unknown structure types and are the first compounds synthesized in the systems SrO/BaO-CuO-As₂O₅-H₂O. Their crystal structures were determined by single-crystal X-ray diffraction [space group C2/c, a=18.536(4) Å, b=5.179(1) Å, c=24.898(5) Å, β=93.67(3)°, V=2344.0(8) Å³, Z=4 for 1; space group P4₂/n, a=7.775(1) Å, c=13.698(3) Å, V=828.1(2) Å³, Z=2 for 2]. The crystal structure of 1 is related to a group of compounds formed by Cu²⁺-(XO₄)³⁻ layers (X=P⁵⁺, As⁵⁺) linked by M cations (M=alkali, alkaline earth, Pb²⁺, or Ag⁺) and partly by hydrogen bonds. In 1, worth mentioning is the very short hydrogen bond length, D···A=2.477(3) Å. It is one of the examples of extremely short hydrogen bonds, where the donor and acceptor are crystallographically different. Compound 2 represents a layered structure consisting of Cu₂O₈ centrosymmetric dimers crosslinked by As1φ₄ tetrahedra, where φ is O or OH, which are interconnected by Ba, As2 and hydrogen bonds to form a three-dimensional network. The layers are formed by Cu₂O₈ centrosymmetric dimers of CuO₅ edge-sharing polyhedra, crosslinked by As1O₄ tetrahedra. Vibrational spectra (FTIR and Raman) of both compounds are described. The spectroscopic manifestation of the very short hydrogen bond in 1, and ABC-like spectra in 2 were discussed.     

Raman scattering investigations on lanthanum-doped Bi4Ti3O12-SrBi4Ti4O15 intergrowth ferroelectrics

The ferroelectric ceramics of Bi₄Ti₃O₁₂, SrBi₄Ti₄O₁₅, and lanthanum-doped Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅ were synthesized, and their Raman spectra were investigated. La-doping resulted in the enlargement of remnant polarization of Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅. The structure of the Bi₂O₂ layers and TiO₆ octahedra of the intergrowth was found to be different from those of Bi₄Ti₃O₁₂ and SrBi₄Ti₄O₁₅. La³⁺ ions exhibit pronounced selectivity for the occupation of A site as La content is lower than 0.50, and tend to be incorporated into Bi₂O₂ layers when the La content is higher than 0.50. Lanthanum substitution brings about the structural phase transition in Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅. The variation of ferroelectric property may be attributed to combined contribution from the decreasing of the oxygen vacancies, the relaxation of the lattice distortion, the destroying of the insulation and the space charge compensation effects of the Bi₂O₂ slabs.     

g-C_3N_4/CaTi_2O_5复合材料制备及其光催化性能

利用类石墨氮化碳(g-C_3N_4)和亚稳相钙钛氧化物(CaTi_2O_5)固相法制备C_3N_4/CaTi_2O_5复合材料。利用X射线衍射(XRD)、金相显微镜、扫描电子显微镜(SEM)及附带能谱分析仪(EDS)和N2吸附-脱附对样品的显微结构和比表面积进行检测分析,并用紫外-可见吸收光度计(UV-Vis)测试了样品的光吸收性能,研究C_3N_4与CaTi_2O_5物质的量之比(nC_3N_4/nCaTi_2O_5)对C_3N_4/CaTi_2O_5复合样品的物相结构和微观形貌的影响,同时考察C_3N_4/CaTi_2O_5复合样品在可见光照射下光催化降解罗丹明染料效果。实验结果表明:相比纯C_3N_4和CaTi_2O_5样品,C_3N_4/CaTi_2O_5复合样品在可见光下具有较高的光催化性能,随着nC_3N_4/nCaTi_2O_5增加,样品的光催化降解率随之增加而后降低,当nC_3N_4/nCaTi_2O_5=1∶1时,样品的光催化降解率达到最大值99.5%,并且循环重复利用5次后,样品的光催化剂降解率仍几乎保持不变。复合样品光催化性能提高主要归因于复合能级结构有效地抑制了电子和空穴复合所致。     

Magnetic diphase nanostructure of ZnFe2O4/γ-Fe2O3

Magnetic diphase nanostructures of ZnFe₂O₄/γ-Fe₂O₃ were synthesized by a solvothermal method. The formation reactions were optimized by tuning the initial molar ratios of Fe/Zn. All samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, and Raman spectra. It is found that when the initial molar ratio of Fe/Zn is larger than 2, a diphase magnetic nanostructure of ZnFe₂O₄/γ-Fe₂O₃ was formed, in which the presence of ZnFe₂O₄ enhanced the thermal stability of γ-Fe₂O₃. Further increasing the initial molar ratio of Fe/Zn larger than 6 destabilized the diphase nanostructure and yielded traces of secondary phase α-Fe₂O₃. The grain surfaces of diphase nanostructure exhibited a spin-glass-like structure. At room temperature, all diphase nanostructures are superparamagnetic with saturation magnetization being increased with γ-Fe₂O₃ content.     

Crystal growth, structural characterization and magnetic properties of Ca3CuRhO6, Ca3Co1.34Rh0.66O6 and Ca3FeRhO6

Single crystals of Ca₃CuRhO₆, Ca₃Co_1.34Rh_0.66O₆ and Ca₃FeRhO₆ were synthesized by high temperature flux growth in molten K₂CO₃ and structurally characterized by single crystal X-ray diffraction. While Ca₃Co_1.34Rh_0.66O₆ and Ca₃FeRhO₆ crystallize with trigonal (rhombohedral) symmetry in the space group , Z=6: Ca₃Co_1.34Rh_0.66O₆a=9.161(1) Å, c=10.601(2) Å; Ca₃FeRhO₆a=9.1884(3) Å, c=10.7750(4) Å; Ca₃CuRhO₆ adopts a monoclinic distortion of the K₄CdCl₆ structure in the space group C2/c, Z=4: a=9.004(2) Å, b=9.218(2) Å, c=6.453(1) Å, β=91.672(5). All crystals of Ca₃CuRhO₆ examined were twinned by pseudo-merohedry. Ca₃CuRhO₆, Ca₃Co_1.34Rh_0.66O₆, and Ca₃FeRhO₆ are structurally related and contain infinite one-dimensional chains of alternating face-sharing RhO₆ octahedra and MO₆ trigonal prisms. In the monoclinic modification, the copper atoms are displaced from the center of the trigonal prism toward one of the rectangular faces adopting a pseudo-square planar configuration. The magnetic properties of Ca₃CuRhO₆, Ca₃Co_1.34Rh_0.66O₆, and Ca₃FeRhO₆ are discussed.