Nonaqueous synthesis of nanosilica in epoxy resin matrix and thermal properties of their cured nanocomposites

Nonaqueous synthesis of nanosilica in diglycidyl ether of bisphenol‐A epoxy (DGEBA) resin has been successfully achieved in this study by reacting tetraethoxysilane (TEOS) directly with DGEBA epoxy matrix, at 80 °C for 4 h under the catalysis of boron trifluoride monoethylamine (BF₃MEA). BF₃MEA was proved to be an effective catalyst for the formation of nanosilica in DGEBA epoxy under thermal heating process. FTIR and ²⁹Si NMR spectra have been used to characterize the structures of nanosilica obtained from this direct thermal synthetic process. The morphology of the nanosilica synthesized in epoxy matrix has also been analyzed by TEM and SEM studies. The effects of both the concentration of BF₃MEA catalyst and amount of TEOS on the diameters of nanosilica in the DGEBA epoxy resin have been discussed in this study. From the DSC analysis, it was found that the nanosilica containing epoxy exhibited the same curing profile as pure epoxy resin, during the curing reaction with 4,4′‐diaminodiphenysulfone (DDS). The thermal‐cured epoxy–nanosilica composites from 40% of TEOS exhibited high glass transition temperature of 221 °C, which was almost 50 °C higher than that of pure DGEBA–DDS–BF₃MEA‐cured resin network. Almost 60 °C increase in thermal degradation temperature has been observed during the TGA of the DDS‐cured epoxy–nanosilica composites containing 40% of TEOS. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 757–768, 2006     

Cure kinetics of carbon nanotube/tetrafunctional epoxy nanocomposites by isothermal differential scanning calorimetry

The cure kinetics of tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM) and 4,4′‐diaminodiphenylsulfone (DDS) as a cure agent in nanocomposites with multiwalled carbon nanotubes (MWNTs) have been studied with an isothermal differential scanning calorimetry (DSC) technique. The experimental data for both the neat TGDDM/DDS system and for epoxy/MWNTs nanocomposites showed an autocatalytic behavior. Kinetic analysis was performed with the phenomenological model of Kamal and a diffusion control function was introduced to describe the cure reaction in the later stage. Activation energies and kinetic parameters were determined by fitting experimental data. For MWNTs/epoxy nanocomposites, the initial reaction rates increased and the time to the maximum rate decreased with increasing MWNTs contents because of the acceleration effect of MWNTs. The values of the activation energies for the epoxy/MWNTs nanocomposites were lower than the values for the neat epoxy in the initial stage of the reaction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3701–3712, 2004     

A flame‐retardant phosphate and cyclotriphosphazene‐containing epoxy resin: Synthesis and properties

A novel flame‐retardant epoxy resin, (4‐diethoxyphosphoryloxyphenoxy)(4‐glycidoxyphenoxy)cyclotriphosphazene (PPCTP), was prepared by the reaction of epichlorohydrin with (4‐diethoxyphosphoryloxyphenoxy)(4‐hydroxyphenoxy)cyclotriphosphazene and was characterized by Fourier transform infrared, ³¹P NMR, and ¹H NMR analyses. The epoxy resin was further cured with diamine curing agents, 4,4′‐diaminodiphenylmethane (DDM), 4,4′‐diaminodiphenylsulfone (DDS), dicyanodiamide (DICY), and 3,4′‐oxydianiline (ODA), to obtain the corresponding epoxy polymers. The curing reactions of the PPCTP resin with the diamines were studied by differential scanning calorimetry. The reactivities of the four curing agents toward PPCTP were in the following order: DDM > ODA > DICY > DDS. In addition, the thermal properties of the cured epoxy polymers were studied by thermogravimetric analysis, and the flame retardancies were estimated by measurement of the limiting oxygen index (LOI). Compared to a corresponding Epon 828‐based epoxy polymer, the PPCTP‐based epoxy polymers showed lower weight‐loss temperatures, higher char yields, and higher LOI values, indicating that the epoxy resin prepared could be useful as a flame retardant. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 972–981, 2000     

Thermal and mechanical properties of a dendritic hydroxyl‐functional hyperbranched polymer and tetrafunctional epoxy resin blends

Blends of a tetrafunctional epoxy resin, tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM), and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 3,3′‐diaminodiphenyl sulfone (DDS) as curing agent. The phase behavior and morphology of the DDS‐cured epoxy/HBP blends with HBP content up to 30 phr were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The phase behavior and morphology of the DDS‐cured epoxy/HBP blends were observed to be dependent on the blend composition. Blends with HBP content from 10 to 30 phr, show a particulate morphology where discrete HBP‐rich particles are dispersed in the continuous cured epoxy‐rich matrix. The cured blends with 15 and 20 phr exhibit a bimodal particle size distribution whereas the cured blend with 30 phr HBP demonstrates a monomodal particle size distribution. Mechanical measurements show that at a concentration range of 0–30 phr addition, the HBP is able to almost double the fracture toughness of the unmodified TGDDM epoxy resin. FTIR displays the formation of hydrogen bonding between the epoxy network and the HBP modifier. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 417–424, 2010     

Nanoindentation studies of polyimide thin films with various internal linkages in the diamine component

Polyimide thin films were synthesized from 3,3′,4,4′‐biphenyltetracarboxylic acid dianhydride (BPDA) and four different diamines (p‐phenylene diamine, 4,4′‐oxydiphenylene diamine, 4,4′‐biphenylene diamine, and 4,4′‐sulfonyldiphenylene diamine). The nanoindentation behavior of the resulting polyimides, namely, poly(p‐phenylene biphenyltetracarboximide) (BPDA‐PDA), poly(4,4′‐biphenylene biphenyltetracarboximide) (BPDA‐BZ), poly(4,4′‐oxydiphenylene biphenyltetracarboximide) (BPDA‐ODA), and poly(4,4′‐sulfonyldiphenylene biphenyltetracarboximide) (BPDA‐DDS), were investigated. Also, the morphological properties were characterized with a prism coupler and wide‐angle X‐ray diffraction and were correlated to the nanoindentation studies. The nanoindentation behavior and hardness varied quite significantly, depending on the changes in the chemical and morphological structures. The hardness of the polyimide thin films increased in the following order: BPDA‐DDS < BPDA‐ODA < BPDA‐BZ < BPDA‐PDA. For all the polyimide thin films, except that of BPDA‐BZ, the hardness decreased with an increase in the load. The birefringence, a measure of the molecular in‐plane orientation, increased in the following order: BPDA‐DDS < BPDA‐ODA < BPDA‐PDA < BPDA‐BZ. The X‐ray diffraction studies revealed that the crystallinity of the polyimide thin films varied with the changes in the chemical structure. The studies showed that the indentation response with an applied load and the hardness by nanoindentation for the BPDA‐based polyimides were closely related to the morphological structure. The nanoindentation and birefringence results revealed that the mechanical properties of the polyimide thin films were dependent on the crystallinity, which arose because of the chain order along the chain axis and the molecular packing order. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 861–870, 2004     

Chemical degradation of TGDDM/DDS epoxy resin in supercritical 1-propanol: Promotion effect of hydrogenation on thermolysis

Chemical decomposition of an epoxy system made of tetraglycidyl 4,4′-diaminodiphenylmethane (TGDDM) and 4,4′-diaminodiphenylsulfone (DDS) in supercritical 1-propanol was investigated under different reaction temperature and time. The GC–MS results suggested that the epoxy system was decomposed to the products including aniline, N-propylbenzenamine, and 4,4′-diaminodiphenylsulfone. The change of the products' yield with time was measured by GC. In addition, the formed chars were characterized by SEM, elemental analysis, Raman and XRD. The results implied the presence of some graphite microcrystals and disordered structure in the solid residue. Upon the addition of KOH, the Guerbet reaction of 1-propanol was promoted to generate more hydrogen. A possible free-radical reaction mechanism was proposed for the depolymerization of TGDDM/DDS epoxy resin. Hydrogenation of radicals had a promotion effect on thermolysis of TGDDM/DDS epoxy resin.     

Chemical structure of networks resulting from curing of N,N-diglycidylaniline-type resins with aromatic amines. IV. Characterization of TGDDM/DDS and TGDDM/DDM networks by high-resolution solid-state 13C-NMR

Cured N,N,N′,N′-tetraglycidyl-4,4′-diaminodiphenylmethane (TGDDM) based epoxy resins were investigated by high-resolution solid-state ¹³C-NMR spectroscopy. Associated hardeners were the most commonly used low reactivity 4,4--diaminodiphenylsulphone (DDS), as well as, for comparisons reasons, the higher reactivity 4,4′-diaminodiphenylmethane (DDM) with, in each case, a1 to 1 or 1 to 0.6 epoxy/NH ratio. In order to interpret the spectra, the poorly resolved aliphatic region was decomposed into elementary lines, the structural assignments of which were made using solution ¹³C-NMR data resulting from a previous model compound study. The main structural feature of all investigated systems is the predominance of small cyclic units resulting from intramolecular reactions of N,N-diglycidylaniline groups. The resins are therefore far less crosslinked that it could be anticipated from the functionality of the reactants. Using the low reactivity DDS still increases this effect, due to a higher proportion of residual non reacted secondary amines. Reducing the initial ratio of hardener could on the contrary lead to a higher proportion of reacted amine function, and thus to a higher crosslinking degree. A qualitative picture of such networks is given at the end.     

Synthesis and characterization of an epoxy based thermoset containing a fluorinated thermoplastic

A novel fluorinated thermoplastic (FT) was synthesized from diglycidyl ether of bisphenol A (DGEBA), and 3‐(trifluoromethyl)aniline. FT was found to be miscible with DGEBA as shown by the existence of a single glass transition temperature (T_g) within the whole composition range. On the basis of several experimental techniques, it was found that upon heating etherification reaction takes place between FT and DGEBA. A DGEBA‐aromatic diamine (4,4′‐methylenebis(3‐chloro 2,6‐diethylaniline) formulation was modified with the FT. The influence of FT on the epoxy‐amine kinetics was investigated. Both structural parameters, gelation, and vitrification, were found to be affected by etherification reaction between epoxy and hydroxyls groups belonging to FT. The presence of ether linkages induced system stoichiometry modification. In addition, the curing conditions influence on FT migration towards the surface was studied on samples prepared with 20 wt % of modifier. SEM–EDX analysis confirmed that modified systems exhibits notable fluorine enrichment within the uppermost 200 μm. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2781–2792, 2007     

气相生长碳纤维对环氧树脂固化反应的影响及其复合物固化动力学研究

用示差扫描量热方法研究了气相生长碳纤维作为填料对4,4′-二氨基二苯甲烷四缩水甘油环氧树脂(TGDDM)/4,4′-二氨基二苯基砜(DDS)等温固化反应的影响.与纯环氧树脂一样,气相生长碳纤维复合物的固化反应也属于自催化反应类型.气相生长碳纤维对环氧树脂的固化反应动力学影响很小.固化反应的过程可以用一种修正过的自催化动力学模型来描述,在整个固化反应过程中纯TGDDM/DDS环氧树脂及其气相生长碳纤维复合物模型拟合得到的结果和实验数据相当一致.     

Novel phthalazinone‐bearing tetrafunctional epoxy: Synthesis,characterization, and their toughening application for TGDDM system

A novel tetrafunctional epoxy (TEPZ) was synthesized by “one spot two steps” method, and the effects of solvents, reaction temperature, and mole ratios of reactants on the reaction conversion were systematically investigated. The results demonstrated that the solvents participating in the reaction were the most crucial factor for high conversions. After curing, TEPZ/4,4′‐diaminodiphenyl sulfone (DDS) system exhibited better thermal stability compared with famous N,N,N′,N′‐tetraglycidyl‐4,4′‐diaminodiphenyl methane (TGDDM)/DDS analog. When TEPZ is blended with TGDDM/DDS, the initial decomposition temperature of TGDDM/TEPZ/DDS hybrid elevated from 348°C to 362°C. The storage modulus and the glass transition temperature were sensitive to curing procedure and concentration of DDS. While the system consisted of 100 phr TGDDM, 30 phr TEPZ, and 40 phr DDS, the storage modulus and glass transition temperature increased significantly compared with those of TGDDM/DDS, and the impact strength increased by 31.6% simultaneously. Such enhancement could be ascribed to the structural feature of phthalazinone in TEPZ, which formed stable interpenetrating networks during thermal cure procedure.     

Curing kinetics and thermal stability of diglycidyl ether of bisphenol

Curing kinetics of diglycidyl ether of bisphenol-A (DGEBA) in the presence of varying molar ratios of aromatic imide-amines and 4,4′-diaminodiphenylsulfone (DDS) were investigated by the dynamic differential scanning calorimetry. The imide-amines were prepared by reacting 1 mole of benzophenone 3,3′,4,4′-tetracarboxylic acid dianhydride (B) with 2.5 moles of 4,4′-diaminodiphenyl ether (E)/ or 4,4′-diaminodiphenyl methane (M)/ or 4,4′-diaminodiphenylsulfone (S) and designated as BE/ or BM/ or BS. The mixture of imide-amines and DDS at ratio of 0:1, 0.25:0.75, 0.5:0.5, 0.75:0.25 and 1:0 were used to investigate the curing behaviour of DGEBA. The multiple heating rate method (5, 10, 15 and 20°C min⁻¹) was used to study the curing kinetics of epoxy resins. The peak exotherm temperature was found to be dependent on the heating rate, structure of imide-amines as well as on the ratio of imide-amine: DDS used. A broad exotherm was observed in the temperature range of 180–230°C on curing with mixture of imide-amines and DDS. Curing of DGEBA with mixture of imide-amines and/or DDS resulted in a decrease in characteristic curing temperatures. Activation energy of curing reaction as determined in accordance to the Ozawa’s method was found to be dependent on the structure of amine. The thermal stability of the isothermally cured resins was also evaluated using dynamic thermogravimetry in a nitrogen atmosphere. The char yield was highest in case of resins cured using mixture of DDS: BS (0.25:0.75; EBS-3), DDS: BM (0.5: 0.5; EBM-2) and DDS: BE (0.5: 0.5; EBE-2).     

含亚胺结构新型磷-氮协效阻燃化合物的合成及对环氧树脂的阻燃作用

采用醛胺缩合反应,以4-(5,5-二甲基-1,3-二氧杂环己内磷酰基)苯甲醛(PCHO)分别与对苯二胺、乙二胺反应合成两种磷酸酯-亚胺双官能化合物阻燃剂(FR:N¹,N⁴-二[4-(5,5-二甲基-1,3-二氧杂环己内磷酰氧基)苯基亚甲基]-1,4-苯二胺(PNB)和N¹,N²-二[4-(5,5-二甲基-1,3-二氧杂环己内磷酰氧基)苯基亚甲基]-1,2-乙二胺(PNE)),研究了FR对4,4'-二氨基二苯砜(DDS)固化双酚A二缩水甘油醚型环氧树脂(DGEBA)体系的阻燃作用及阻燃机理。 研究发现FR的引入显著提高了DGEBA/DDS在700 ℃时的残炭率(R_c),同时提升了材料的阻燃性能,其中以乙二胺合成的PNE阻燃性能显著优于以苯二胺合成的PNB。 当磷添加质量分数为1.5%时,PNE-1.5/DGEBA/DDS在N₂气下的R_c为35.1%,在空气下的R_c为14.4%,极限氧指数(LOI)为33.2%,并可达阻燃等级UL-94最高阻燃级别V-0级。 同时,PNE-1.5/DGEBA/DDS相较于DGEBA/DDS保持了弯曲强度和76%以上的冲击强度,机械性能显著优于PNB-1.5/DGEBA/DDS。 通过阻燃机理分析FR在DGEBA/DDS体系中具有凝聚相、气相及磷-氮协效共同作用的阻燃特点。 磷酸酯-亚胺双官能团化合物FR对环氧树脂体系具有良好的阻燃作用,其中PNE阻燃效率高、机械性能负面影响小,具有潜在应用价值。     

Interfacial and wetting properties of carbon fiber reinforced epoxy composites with different hardeners by electrical resistance measurement

In this research, interfacial and wetting properties of N,N,N,N-tetraglycidyl-4,4-diaminodiphenylmethane (TGDDM) epoxy resin with two hardeners with different chemical structure were evaluated by electrical resistance (ER) measurement. The heat of reaction of TGDDM epoxy with the two different hardeners, 33 and 44 di-amino di-phenyl sulphone (DDS), was analyzed by differential scanning calorimetry (DSC). The TGDDM epoxy exhibited different mechanical properties with the two different DDS hardeners. Combined ER, wetting measurements and the microdroplet test were used for evaluating the spreading effect and interfacial shear strength (IFSS) of carbon fiber (CF) reinforced TGDDM epoxy composites with these different hardeners. The heat of reaction and mechanical properties of TGDDM/DDS were influenced by the chemical structure and different free volumes of the epoxy resins. The relationships between the ER-wetting results and the IFSS were internally consistent. Ultimately it was demonstrated that ER measurements makes it possible to estimate the interfacial and wetting properties of CF reinforced epoxy composites.     

A systematic study of the microwave and thermal cure kinetics of the DGEBA/DDS and DGEBA/DDM epoxy‐amine resin systems

The microwave and thermal cure processes for the epoxy-amine systems (epoxy resin diglycidyl ether of bisphenol A, DGEBA) with 4,4′-diaminodiphenyl sulphone (DDS) and 4,4′-diaminodiphenyl methane (DDM) have been investigated for 1 : 1 stoichiometries by using fiber-optic FT-NIR spectroscopy. The DGEBA used was in the form of Ciba-Geigy GY260 resin. The DDM system was studied at a single cure temperature of 373 K and a single stoichiometry of 20.94 wt% and the DDS system was studied at a stoichiometry of 24.9 wt% and a range of temperatures between 393 and 443 K. The best values of the kinetic rate parameters for the consumption of amines have been determined by a least squares curve fit to a model for epoxy/amine cure. The activation energies for the polymerization of the DGEBA/DDS system were determined for both cure processes and found to be 66 and 69 kJ mol⁻¹ for the microwave and thermal cure processes, respectively. No evidence was found for any specific effect of the microwave radiation on the rate parameters, and the systems were both found to be characterized by a negative substitution effect. Copyright © 2002 John Wiley & Sons, Ltd.     

High resolution solid‐state 13C‐NMR study of as‐cured and irradiated epoxy resins

This article presents the effects of strong ionizing radiations on the physico‐chemical modifications of aliphatic or aromatic amine‐cured epoxy resins based on diglycidyl ether of bisphenol A (DGEBA). Such epoxy resins have a considerable number of applications in the nuclear industrial field and are known to be very stable under moderate irradiation conditions. Using extensively high resolution solid‐state ¹³C‐NMR spectroscopy we show that the aliphatic amine‐cured resin (DGEBA‐TETA) appears much more sensitive to gamma rays than the aromatic amine‐cured one (DGEBA‐DDM). On the one hand, qualitative analyses of the high resolution solid‐state ¹³C‐NMR spectra of both epoxy resins, irradiated under similar conditions (8.5 MGy), reveal almost no change in the aromatic amine‐cured resin whereas new resonances are observed for the aliphatic amine‐cured resin. These new peaks were interpreted as the formation of new functional groups such as amides, acids and/or esters and to alkene groups probably formed in the aliphatic amine skeleton. On the other hand, molecular dynamics of these polymers are investigated by measuring the relaxation times, T_CH, T_1ρH and T_1C , before and after irradiation. The study of relaxation data shows the formation, under irradiation, of a more rigid network, especially for the aliphatic amine‐cured system and confirms that aromatic amine‐cured resin [DGEBA‐4,4′‐diaminodiphenylmethane(DDM)] is much less affected by ionizing radiations than the aliphatic amine‐cured resin [DGEBA‐triethylenetetramine(TETA)]. Moreover, it has been shown that the molecular modifications generated by irradiation on the powder of the aliphatic‐amine‐cured resin appear to be homogeneously distributed inside the polymers as no phase separations can be deduced from the above analyses. Copyright © 2001 John Wiley & Sons, Ltd.     

Novel,environmentally friendly crosslinking system of an epoxy using an amino acid: Tryptophan‐cured diglycidyl ether of bisphenol A epoxy

Tryptophan, an amino acid, has been used as a novel, environmentally friendly curing agent instead of toxic curing agents to crosslink the diglycidyl ether of bisphenol A (DGEBA) epoxy resin. The curing reaction of tryptophan/DGEBA mixtures of different ratios and the effect of the imidazole catalyst on the reaction have been evaluated. The optimum reaction ratio of DGEBA to tryptophan has been determined to be 3:1 with 1 wt % catalyst, and the curing mechanism of the novel reaction system has been studied and elucidated. In situ Fourier transform infrared spectra indicate that with the extraction of a hydrogen from NH₃⁺ in zwitterions from tryptophan, the formed nucleophilic primary amine and carboxylate anions of the tryptophan can readily participate in the ring‐opening reaction with epoxy. The secondary amine, formed from the primary amine, can further participate in the ring‐opening reaction with epoxy and form the crosslinked network. The crosslinked structure exhibits a reasonably high glass‐transition temperature and thermal stability. A catalyst‐initiated chain reaction mechanism is proposed for the curing reaction of the epoxy with zwitterion amino acid hardeners. The replacement of toxic curing agents with this novel, environmentally friendly curing agent is an important step toward a next‐generation green electronics industry. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 181–190, 2007     

Novel quaternary ammonium borates as latent catalysts for epoxy–phenolic resins

Novel tetrabutylammonium tetrakis(substituted benzoyloxy)borate salts ( 1a – 1d ) were synthesized by the reaction of tetrabutylammonium tetraphenylborate and corresponding substituted benzoic acids. Polyaddition reactions of diglycidyl ether of bisphenol A (DGEBA) and 4,4′‐bisphenol F (44BPF) or bisphenol F (BPF‐D) with the ammonium borates were investigated as model reactions of epoxy/phenol–novolac resin systems with respect to the thermal latency and storage stability of the catalyst. The polyaddition of DGEBA/44BPF with the ammonium borates in diglyme at 150 °C for 6 h proceeded up to 84–94% conversions and gave polymers with number‐average molecular weights of 3750–5750, whereas the polyaddition at 80 °C for 6 h gave less than 9% conversions. The catalytic activity of ammonium borates 1a – 1d depended on the substituent of the phenyl group of the borates, and the order of activity was 1b (p‐OMe) > 1a (? H) > 1c (p‐NO₂) > 1d [3,5‐(NO₂)₂]. The ammonium borate catalyst with the substituent that yielded lower acidity of the corresponding substituted benzoic acid tended to reveal higher activity. In comparison with tetrabutylammonium bromide (TBAB) as a conventional ammonium salt, 1a – 1d revealed better thermal latency. The storage stability of DGEBA/BPF‐D with the ammonium borate catalysts in bulk at 40 °C was better than that with TBAB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2689–2701, 2002     

Pyrolysis and fire behaviour of epoxy systems containing a novel 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide-(DOPO)-based diamino hardener

Highly soluble 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide-(DOPO)-based diamino hardener (2), bearing its amino groups directly on the DOPO framework, is investigated with respect to its use as a reactive flame retardant in thermosets. A mechanism for decomposition of the corresponding phosphorus-modified epoxy resin system based on a diglycidylether of bisphenol A DGEBA and 2 (DGEBA/2) is proposed and compared to the systems using DGEBA and 4,4′-diaminodiphenylsulfon (DGEBA/DDS) and to a similar system based on the structurally comparable non-reactive DOPO-based compound (DGEBA/DDS/1). Additive 1 changed the decomposition characteristics of the epoxy resin only slightly and phosphorus was released. Incorporating 2 induces two-step decomposition and most of the phosphorus remains in the residue. Furthermore, the fire behaviour of neat epoxy resin systems and a representative carbon fibre-reinforced composite based on DGEBA, DDS and 2 (DGEBA/DDS/2) were examined and compared to that of the analogous composite systems based on DGEBA/DDS and DGEBA/DDS/1. Based on different flame retardancy mechanisms both the reactive compound 2 and the additive compound 1 improve flammability (increase in LOI >13% and achieving V-1 behaviour) of the epoxy resin and composites. Under forced flaming only the flame inhibition of the additive compound 1 acts sufficiently. Lastly, the superior key mechanical properties of the epoxy resin and composite based on 2 are sketched.     

高性能环氧树脂/碳纳米管复合物的热分析研究

用差示扫描量热仪(DSC)、热失重分析仪(TGA)和动态力学热分析仪(DMTA)研究了多壁碳纳米管(MWNTs)/高性能4,4′-二氨基二苯甲烷四缩水甘油环氧树脂(TGDDM)/4,4′-二氨基二苯基砜(DDS)复合物的热性能.Kissinger和Flynn-Wall-Ozawa的非等温固化动力学研究发现,随着MWNTs含量的增加,复合物固化反应的活化能先减小后增大.TGA研究表明,MWNTs的添加对环氧树脂热稳定性影响很小.碳纳米管填充到TGDDM/DDS体系后,复合物的储存模量随着MWNTs含量的增加而增大,而玻璃化温度却随之减小.