Thin Layer Membrane Systems as Rapid Development Tool for Potentiometric Solid Contact Ion‐selective Electrodes

The use of thin membrane layer ion‐selective electrodes (of ～200 nm thickness) as rapid diagnosis tool is proposed. While conventional solid contact systems (with a membrane of ～250 μm thickness) may exhibit a satisfactory stability for regular laboratory use, a signal degradation can still be distinguished over a longer period of time but this requires tedious and time consuming tests. By diminishing the thickness of the membrane by a factor of 10³ approximately, diffusion processes happen faster, and the lifetime is significantly reduced. This would ordinarily be a strong drawback but not if the aim is to detect a membrane deterioration in a shorter time frame. This characteristic makes thin membrane systems an ideal tool for rapid complications identification in the development process of conventional solid contact electrodes. The approach is demonstrated here in the development of an all new solid contact probe for anions. PEDOT?C₁₄, a conducting polymer, was used for the first time in a solid contact electrode with an anion exchange membrane for the detection of nitrate. The thin layer configuration was used to optimise the polymerisation parameters as well as the membrane composition without having to run week‐long trials. A stable conventional solid contact electrode was in the end successfully developed and exhibited a lower detection limit of 10^?5.5 M for nitrate with a stable Nernstian response for several days.     

Voltammetric Properties of All‐solid State Ion‐selective Electrodes with Multiwalled Carbon Nanotubes‐poly(3‐octylthiophene‐2,5‐diyl) Nanocomposite Transducer

Voltammetric response of an all‐solid‐state ion‐selective electrode was studied on example of potassium‐selective sensor with poly(vinyl chloride) based membrane and nanocomposite transducer containing poly(3‐octylthiophene‐2,5‐diyl) and multiwalled carbon nanotubes. Factors limiting the rate of the electrochemical process and the response were discussed. The challenge in voltammetric applications of ion‐selective electrodes is thickness of the plastic membrane. It was found that although a relatively thick ion‐selective membrane was applied, as typically used in potentiometric studies, the position of the reduction peak, corresponding to potassium ions incorporation, was dependent on ions concentration in a Nernstian manner. This opens possibility of deviation from the paradigm of ultrathin membranes in voltammetric applications, thus potentially extending the sensors lifetime. The high resistance of the membrane did not affect the voltammetric characteristics, because the resistance was independent of ions concentration in solution. On the other hand, high resistance results in charge trapping effect in the solid contact material, leading to advantageous retention of the oxidized‐conducting state of the solid contact, independently of the applied electrode potential.     

Novel Solid‐Contact Ion‐Selective Microelectrodes for Localized Potentiometric Measurements

The design and properties of novel type of solid‐contact ionophore‐based ion‐selective microelectrodes are reported. The microelectrode is based on an insulated needle‐shaped metallic wire with an exposed apex. The ion‐to‐electron transducer is made of poly(3‐octylthiophene‐2,5‐diyl) and placed between an ion‐selective membrane and the metallic tip. The ion‐selective polyvinyl chloride‐based membrane is deposited atop the layer of conductive polymer. The length of the ion‐sensitive part of the electrode is less than 10 μm. pH and Mg²⁺‐selective microelectrodes were constructed and tested showing stable potential and fast response that are essential properties for the practical application of microelectrodes for localized scanning measurements.     

Development of Miniature Solid Contact Ion Selective Electrodes for in situ Instrumentation

Using a standardized miniature format ion selective electrode, five different carbon based solid contact materials, including a novel commercially available graphene oxide assisted carbon nanotube dispersion (Flexiphene^TM), were compared. The electromotive force (EMF) response, stability, and behavior following storage was evaluated. Bulk resistance for the novel graphene oxide/carbon nanotube (GO‐CNT) based ISE was observed to be 0.09±0.03 MΩ, which is two orders of magnitude lower than reported for either component in isolation. The results for previously described solid contact materials are in general agreement with the literature, and the tradeoffs between solid contact layer material choices are discussed. Performance of GO‐CNT solid contact ion selective electrodes were then evaluated in a 3D‐printed fluidic array to determine their suitability for future in situ instruments.     

Advantages of Amperometric Readout Mode of Ion‐selective Electrodes under Potentiostatic Conditions

Amperometric responses of all‐solid‐state ion‐selective electrodes, recorded under potentiostatic conditions, were studied on example of potassium‐selective sensors with polypyrrole solid contact, at potential corresponding to reduction of the solid contact material and accompanying transfer of potassium ions across the membrane. Selective and stable in time linear dependences of current vs. logarithm of analyte concentration were recorded, resulting from high membrane resistance and changing membrane potential. The influence of experimental parameters as applied potential or thickness of the membrane was discussed. Advantages of the amperometric mode compared to potentiometric one relate to possibility of tailoring analytical parameters (sensitivity, magnitude of the signal) as well as over one order of magnitude decrease of the detection limit. The latter effect is achieved due to externally forced incorporation of potassium ions from the solution to the membrane, compensating their spontaneous release to the sample solution. A method of experimental setup simplification was proposed, with application of two‐electrode system, which can be used in the absence of external polarization source. The required driving force for the current flow was assured by spontaneous oxidation process occurring at the second electrode, coupled with reduction of the solid contact material of the ion‐selective electrode. In this case also stable in time calibration plots can be recorded.     

Solid Contact Nitrate Ion‐Selective Electrode Based on Ionic Liquid with Stable and Reproducible Potential

A simple, fast and cheap method of preparation of solid contact nitrate ion‐selective electrode is proposed. The electrode membrane phase consist of only three components: PVC, plasticizer and ionic liquid (IL).The ionic liquid trihexyltetradecylphosphonium chloride is used in triple function as ionophore, as lipophilic ionic component in order to reduce membrane resistance, and as transducer media in order to stabilize the potential of internal Ag/AgCl electrode. The electrical properties of the membrane were studied by electrochemical impedance spectroscopy and the influence of the interfacial water film was evaluated by potentiometric water layer test.     

Lead Ion‐Selective Polypyrrole Solid‐Contact Electrode Based on Crown Ether

Abstract

The lead(II) ion selective solid‐contact electrode based on polypyrrole film, covered with a polyvinyl chloride membrane has been prepared. Polypyrrole film was used as a mediating layer of the solid‐contact electrode due to the conductivity. Crown ether has been used as ionophores in polyvinyl chloride cocktail solutions. This solid‐contact electrode based on benzo‐15‐crown‐5 exhibited Nernstian‐response within 30 s response time over concentration range, 1×10^?1～5×10^?7 M. The selectivity of this electrode to other metal cations was comparatively good. This electrode showed much better results, such as detection range, slope, response time and reproducibility than conventional ion selective electrode and coated wire electrode.     

An All‐solid‐state Polymeric Membrane Ca2+‐selective Electrode Based on Hydrophobic Alkyl‐chain‐functionalized Graphene Oxide

An all‐solid‐state polymeric membrane Ca²⁺‐selective electrode based on hydrophobic octadecylamine‐functionalized graphene oxide has been developed. The hydrophobic composite in the ion‐selective membrane not only acts as a transduction element to improve the potential stability for the all‐solid‐state Ca²⁺‐selective electrode, but also is used to immobilize Ca²⁺ ionophore with lipophilic side chains through hydrophobic interactions. The developed all‐solid‐state Ca²⁺‐selective electrode shows a stable potential response in the linear range of 3.0×10⁻⁷–1.0×10⁻³ M with a slope of 24.7±0.3 mV/dec, and the detection limit is (1.6±0.2 )×10⁻⁷ M (n =3). Additionally, due to the hydrophobicity and electrical conductivity of the composite, the proposed all‐solid‐state ion‐selective electrode exhibits an improved stability with the absence of water layer between the ion‐selective membrane and the underlying glassy carbon electrode. This work provides a simple, efficient and low‐cost methodology for developing stable and robust all‐solid‐state ion‐selective electrode with ionophore immobilization.     

Conducting Polymer‐Based Solid‐State Ion‐Selective Electrodes

Conducting polymers, i.e., electroactive conjugated polymers, are useful both as ion‐to‐electron transducers and as sensing membranes in solid‐state ion‐selective electrodes. Recent achievements over the last few years have resulted in significant improvements of the analytical performance of solid‐contact ion‐selective electrodes (solid‐contact ISEs) based on conducting polymers as ion‐to‐electron transducer combined with polymeric ion‐selective membranes. A significant amount of research has also been devoted to solid‐state ISEs based on conducting polymers as the sensing membrane. This review gives a brief summary of the progress in the area in recent years.     

Tailoring Solution Cast Poly(3,4‐dioctyloxythiophene) Transducers for Potentiometric All‐Solid‐State Ion‐Selective Electrodes

A novel concept of tailoring potentiometric responses of all‐solid‐state ion‐selective electrodes was introduced. The effect of composition and resulting properties of the conjugated polymer transducer, placed between the electrode support and ion‐selective membrane, on analytical characteristic of obtained sensors was studied.     

Influence of Poly(3‐octylthiophene) on the Water Transport Through Methacrylic‐Acrylic Based Polymer Membranes

Accumulation of water in ion‐selective membranes, can lead to inconsistent potentiometric responses with solid‐contact ion‐selective electrode (SC‐ISE) formats, and hence it is essential to restrain their water uptake. We have used FTIR‐ATR spectroscopy to study how the water uptake is influenced by the intermixing of a poly(3‐octylthiophene) (POT) SC and a poly(methyl methacrylate):poly(n‐decyl methacrylate) (PMMA:PDMA) based polymeric membrane matrix, the only SC‐ISE system for which direct evidence was provided on the aqueous layer elimination. Numerical simulations of the FTIR‐ATR spectra of 1 or 5 wt% POT containing PMMA:PDMA membranes showed that the addition of 5 wt% POT to the membrane lowered the equilibrium water uptake, whereas the diffusion coefficients of water in the membrane were found to be less affected. Consequently, POT is beneficial for preventing the formation of detrimental water layers in the SC‐ISE structure.     

Ion‐selective Electrodes with 3D Nanostructured Conducting Polymer Solid Contact

Until now both ion‐to‐electron transducers as well as large surface area nanostructured conducting materials were successfully used as solid contacts for polymer‐based ion‐selective electrodes. We were interested to explore the combination of these two approaches by fabricating ordered electrically conducting polymer (ECP) nanostructures using 3D nanosphere lithography and electrosynthesis to provide a high surface area and capacitive interface for solid contact ion‐selective electrodes (SC‐ISEs). For these studies we used poly(3,4‐ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT(PSS)) films with 750 nm diameter interconnected pores as the intermediate layer between a glassy carbon electrode and a Ag⁺ ‐selective polymeric membrane. We also investigated the feasibility of loading the voids created in the polymer film with a lipophilic redox mediator (1,1’‐dimethylferrocene) to provide the respective ISEs with well‐defined/controllable E⁰ values. These expectations were fulfilled as the standard deviation of E⁰ values were reduced with almost an order of magnitude for 3D nanostructured SC‐ISEs filled with the redox mediator as compared to their redox mediator‐free analogs. The detrimental effect of the redox mediator extraction into the plasticized PVC‐based ion‐selective membrane (ISM) was efficiently suppressed by replacing the PVC‐based ISMs with a low diffusivity silicone rubber matrix.     

Polyion Detection via All‐solid‐contact Paper‐based Polyion‐sensitive Polymeric Membrane Electrodes

The first all‐solid‐contact paper‐based single‐use polyion‐sensitive ion‐selective electrodes (ISEs) are described. These polyion‐sensitive ISEs are fabricated using cellulose filter paper coated with a carbon ink conductive layer. A polyanion sensing membrane is cast on a section of the coated paper and the sensor is insulated, resulting in a disposable, single‐use device. Various polyanions are shown to yield large negative potentiometric responses when using these disposable devices for direct polyanion detection. These new sensors are further demonstrated to be useful in indirect polycation detection when polycations (i. e., polyquaterniums (PQs)) are titrated with polyanionic dextran sulfate (DS). Titrations monitored using these paper‐based, all‐solid‐contact devices yield endpoints proportional to the given PQ concentration present in the test sample.     

Implementation of a Chloride‐selective Electrode Into a Closed Bipolar Electrode System with Fluorimetric Readout

Applicability of a bipolar electrode system was tested for arrangements containing a typical ion‐selective electrode (ISE) connected with an electrode coated by a conducting polymer characterized by electroluminescence. In this case a selective response of the ISE membrane at one pole of the bipolar electrode is transduced to a fluorimetric signal obtained by reduction of the conducting polymer at the second pole. This signal transformation mode was studied on example of a simple closed bipolar electrode system composed of all‐solid‐state chloride‐selective electrode with polypyrrole transducer as the sensing pole and the reporting pole represented by electrode coated by poly(3‐octylthiophene) (POT) layer characterized by fluorescence in the neutral state. In this system selective and linear dependences of fluorimetric signal on logarithm of chloride ions concentration in turn‐on mode were recorded for optimized external voltage applied. Alternatively, a concept of cascade bipolar electrode system with incorporation of additional bipolar electrode being a polarization source for the sensing bipolar electrode with ISE and POT layer was also tested. A significant advantage of the cascade system is its possibility to work spontaneously without external polarization. For this case also linear calibration plots of fluorimetric signal vs. logarithm of analyte concentration were recorded.     

The Influence of the Conditioning Procedure on Potentiometric Characteristics of Solid Contact Calcium‐Selective Electrodes in Nanomolar Concentration Solutions

A solid contact calcium‐selective electrode with a poly(pyrrole) intermediate layer doped with the calcium ion‐complexing ligand Tiron was successfully constructed and examined towards the possibility of lowering the detection limit. Two calcium ionophores, ETH 1001 and ETH 129, were compared. A variety of different shapes of potentiometric responses can be obtained in a controlled manner by applying an appropriate conditioning procedure. The lifetime of the investigated electrodes was longer than 1 year. The modified poly(pyrrole) solid contact electrode was compared with the coated wire type. An inductively coupled plasma mass spectrometry with laser ablation analysis (LA ICP MS) was used to confirm the transmembrane ion fluxes.     

Optimizing Carbon Nanotubes Dispersing Agents from the Point of View of Ion‐selective Membrane Based Sensors Performance – Introducing Carboxymethylcellulose as Dispersing Agent for Carbon Nanotubes Based Solid Contacts

The influence of dispersing agent used to prepare carbon nanotubes solid‐contact on the performance of all‐solid state ion‐selective electrodes has been evaluated. It is shown that excess of surfactant dispersing agent is leading to deterioration of sensor performance, however, removal of dispersing agent – a typically applied approach – is resulting in substantial change of transducer layer physical properties, which can influence sensor performance. As remedy we propose application of a polymeric dispersing agent – carboxymethylcellulose. Thus obtained ion‐selective electrodes are characterized by high potential readings stability both within day and between days.     

All-solid-state potentiometric sensors for ascorbic acid by using a screen-printed compatible solid contact

The development of all-solid-state potentiometric ion selective electrodes for monitoring of ascorbic acid, by using a screen-printed compatible solid contact is described. The applied methodology is based on the use of PVC membrane modified with some firstly-tested ionophores (triphenyltin(IV)chloride, triphenyltin(IV)hydroxide and palmitoyl-l-ascorbic acid) and a novel one synthesized in our laboratory (dibutyltin(IV) diascorbate). Synthesis protocol and some preliminary identification studies are given. A conductive graphite-based polymer thick film ink was used as an internal solid contact between the graphite electrode and the PVC membrane. The presence and the nature of the solid contact (plain or doped with lanthanum 2,6-dichlorophenolindophenol (DCPI)) seem to enhance the analytical performance of the electrodes in terms of sensitivity, dynamic range, and response time. The analytical performance of the constructed electrodes was evaluated with potentiometry, constant-current chronopotentiometry and electrochemical impedance spectroscopy (EIS). The interference effect of various compounds was also tested. The potential response of the optimized Ph₃SnCl-based electrode was linear against ascorbic acid concentration range 0.005-5.0 mM. The applicability of the proposed sensors in real samples was also tested. The detection limit was 0.002 mM ascorbic acid (50 mM phosphate, pH 5 in 50 mM KCl). The slope of the electrodes was super-Nernstian and pH dependent, indicating a mechanism involving a combination of charge transfer and ion exchange processes. Fabrication of screen-printed ascorbate ISEs has also been demonstrated.     

Single‐Piece Solid‐Contact Pb2+‐Selective Electrodes Based on Thiophene Oligomer

A single‐piece solid‐contact Pb²⁺‐selective electrode was prepared by adding a thiophene oligomer into the ion‐selective cocktail directly. The one‐step fabrication yielded an electrode with Nernstian response spanning a wide concentration range of 10^?3–10^?8 mol L^?1, and detection limit as low as 5.6×10^?9 mol L^?1. The electrode had a quick response time of approximately 10–15 s and showed excellent selectivity over the most common univalent and divalent cations. The practical application of the proposed electrode has been tested by determining Pb²⁺ in real water samples.     

All‐Solid‐State Ion Selective and All‐Solid‐State Reference Electrodes

This paper is aiming to give a brief overview of recent research in the field of all‐solid‐state, internal solution free, ion‐selective electrodes and reference electrodes, employing conducting polymers or nano‐/microstructures as solid contacts beneath the polymeric, ion‐selective or reference membranes. The emphasis is on papers published in the last five years (after 2006). According to the papers published, poly(3‐octylthiophene) conducting polymer transducers offer highly reliable sensors for various applications, involving demanding analytical approaches and miniature sensors. On the other hand, the search for alternative materials continues: the sensors obtained by placing nano‐/microstructures (conducting polymers but also other materials, like, e.g., carbon nanotubes) underneath the receptor membrane are intensively tested. The recent years have also shown how useful the application of advanced instrumental methods is for the investigation of processes occurring within all‐solid‐state ion‐selective electrodes.     

Simultaneous Determination of Na+, K+, Ca2+, Mg2+ and Cl− in Unstimulated and Stimulated Human Saliva Using All Solid State Multisensor Platform

Human saliva is one of the body fluids which collection method is relatively simple and non‐invasive. The article is dedicated to assess concentration (activity) of Na⁺, K⁺, Ca²⁺, Mg²⁺ and Cl⁻ in fresh, unstimulated or stimulated human saliva samples using single solid contact ion‐selective electrodes with conventional reference electrode and self‐made multisensor platform (MP) equipped with ion‐selective membranes for Na⁺, K⁺, Ca²⁺, Mg²⁺ and Cl⁻ and reference electrode made in solid state technology, based on dispersed KCl in the polymer. Both kind of electrodes, single ISE and miniaturized electrodes in multisensor platform (ISE‐MP) were made of glassy carbon. The electrode surfaces have been modified by conductive polymer (PEDOT) layer deposition; with the exception of Cl⁻ electrode, in which conducting polymer was not applied. Potentiometric measurements were used to compare the changes of the ionic composition in various samples of saliva.