氮化硼纳米片负载Pd(OAc)2催化剂的制备及催化微波辅助Heck反应

以液相超声剥离的氮化硼纳米片(BNNSs)为载体, 通过表面羟基、 氨基、 席夫碱共价功能化后与Pd ²⁺配位, 制备负载型催化剂Pd@BNNSs-Schiff, 并将该催化剂应用于微波辅助的Heck反应. 通过傅里叶红外光谱(FTIR)、 激光拉曼(Raman)光谱、 X射线衍射(XRD)、 同步热分析(TGA)、 X射线光电子能谱(XPS)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)和元素分布分析(EDS mapping)对催化剂的结构和形貌进行了表征. 结果表明, 当苯乙烯与碘苯摩尔比为1.25∶1, 溶剂为N,N-二甲基甲酰胺, 缚酸剂为三乙胺, 催化剂Pd用量为0.08%(质量分数)时, 以450 W功率微波辐射20 min收率最高为95.6%; 催化活性明显优于以相同方法制备的催化剂Pd@GO-Schiff(78.3%)(GO=氧化石墨烯); Pd@BNNSs-Schiff循环利用6次后仍具有较高的催化活性,参照催化剂在循环3次后活性明显降低, 7次后失活.     

Cu_xCo_(1-x)/Al_2O_3/FeCrAl整体式催化剂上甲苯催化燃烧(英文)

以FeCrAl合金薄片为基底,Al2O3浆料为过渡胶体,不同摩尔比的Cu、Co为催化活性组分,制备了一系列CuxCo1-x/Al2O3/FeCrAl(x=0-1)新型整体式催化剂.采用X射线粉末衍射(XRD),扫描电子显微镜(SEM),X光电子能谱(XPS)和程序升温还原(TPR)等手段对催化剂的结构进行了表征.在微型固定床反应器上评价了催化剂的催化甲苯燃烧性能.研究结果表明:在所制备的整体式催化剂上,当Cu含量比较低时,形成了Cu-Co-O固溶体;当Cu含量比较高时,可以测得CuO的衍射峰.催化剂表面颗粒大小和形貌与Cu、Co摩尔比密切相关.在催化剂表面,Co以Co2+和Co3+价态存在,而Cu主要以Cu2+价态存在.催化剂中的Cu可以改善Co的氧化还原性,从而有利于催化剂活性的提高.在所制备的催化剂中,Cu0.5Co0.5/Al2O3/FeCrAl催化剂具有最好的活性,甲苯在374oC可以完全催化燃烧消除.     

用于高性能锂-硫电池的氮化硼纳米片/碳纤维改性隔膜

通过静电纺丝、热亚胺化和碳化过程,将氮化硼纳米片(BNNSs)负载在碳纤维(CFs)表面,组成用于修饰商业聚丙烯(PP)隔膜的氮化硼纳米片/碳复合纤维(BNNSs/CFs)复合材料。BNNSs和CFs的协同作用为电池提供了额外的导电路径,并将可溶性多硫化锂固定在正极区域。结果表明,采用10BNNSs/CFs-PP隔膜的电池在0.05C下的初始放电容量高达1 295.7 mAh·g^-1,当电流密度增加到1C时,以10BNNSs/CFs-PP为隔膜的电池也具有良好的长期循环稳定性,在400次循环后最终容量高达568.1mAh·g^-1,每次循环容量衰减0.073%。     

用于高性能锂-硫电池的氮化硼纳米片/碳纤维改性隔膜

通过静电纺丝、热亚胺化和碳化过程,将氮化硼纳米片(BNNSs)负载在碳纤维(CFs)表面,组成用于修饰商业聚丙烯(PP)隔膜的氮化硼纳米片/碳复合纤维(BNNSs/CFs)复合材料。BNNSs和CFs的协同作用为电池提供了额外的导电路径,并将可溶性多硫化锂固定在正极区域。结果表明,采用10BNNSs/CFs-PP隔膜的电池在0.05C下的初始放电容量高达1 295.7 mAh·g^-1,当电流密度增加到1C时,以10BNNSs/CFs-PP为隔膜的电池也具有良好的长期循环稳定性,在400次循环后最终容量高达583.1mAh·g^-1,每次循环容量衰减0.069%。     

用于高性能锂-硫电池的氮化硼纳米片/碳纤维改性隔膜

通过静电纺丝、热亚胺化和碳化过程,将氮化硼纳米片(BNNSs)负载在碳纤维(CFs)表面,组成用于修饰商业聚丙烯(PP)隔膜的氮化硼纳米片/碳复合纤维(BNNSs/CFs)复合材料。BNNSs和CFs的协同作用为电池提供了额外的导电路径,并将可溶性多硫化锂固定在正极区域。结果表明,采用10BNNSs/CFs-PP隔膜的电池在0.05C下的初始放电容量高达1 295.7 mAh·g^-1,当电流密度增加到1C时,以10BNNSs/CFs-PP为隔膜的电池也具有良好的长期循环稳定性,在400次循环后最终容量高达568.1mAh·g^-1,每次循环容量衰减0.073%。     

花生壳基多孔碳负载Pd-Co催化剂应用于碱性介质中电氧化甲醇

以花生壳为原料,经KOH活化制备花生壳基多孔碳(HC)。氮气吸附-脱附研究表明,所获得的多孔碳的总表面积高达1 645 m²·g^-1。采用浸渍还原法制备了以HC为载体的Pd-Co/HC催化剂。X射线衍射(XRD)和X射线光电子能谱(XPS)分析表明,催化剂中的Co主要以Co和Co O的形式存在,Co进入Pd的晶格并形成Pd-Co合金。Pd-Co/HC_0.5-700的透射电子显微镜(TEM)结果显示,Pd-Co纳米颗粒具有较小粒径(约4 nm)且成功地分散在HC上。Pd-Co/HC_0.5-700在碱性介质中电催化氧化甲醇时表现出优秀的电催化活性、稳定性和CO耐受性,这种显著的高性能可以归因于生物质载体大的表面积和Co的成功掺杂。     

[NiFe/Cu/Co/Cu]n纳米多层线的电化学制备及表征

采用电沉积法,在阳极氧化铝(AAO)模板中制备了[NiFe/Cu/Co/Cu]_n多层纳米线.利用扫描电子显微镜(SEM)及透射电子显微镜(TEM)对纳米多层线的表面形貌及结构进行了表征,纳米线阵列高度有序、直径均一、层状结构清晰,NiFe层厚度约40 nm,Cu层厚度约60 nm,Co层厚度约15 nm,各子层厚度可控.利用X射线能谱分析仪(EDS)对纳米多层线NiFe层的成分进行了测试,Ni,Fe的原子比为4:1.利用X射线衍射仪(XRD)对[NiFe/Cu/Co/Cu]_n纳米多层膜和多层线结构进行了测试,多层膜为面心立方(fcc)结构,多层线NiFe层为面心立方(fcc)结构,Cu层为六方密排hcp(100),Co层为面心立方(fcc)结构.与组成、结构完全相同的多层膜相比,[NiFe/Cu/Co/Cu]_n多层纳米线具有更优越的巨磁电阻性能.     

CuxCo1-x/Al2O3/堇青石整体式催化剂的制备及其催化甲苯燃烧性能

以堇青石蜂窝陶瓷为基底,A12O3浆料为过渡胶体,Cu和Co为催化活性组分,制备了一系列CuxCo1-x/Al2O3/堇青石(x=0～1)整体式催化剂.采用X射线衍射、X射线光电子能谱、扫描电镜和程序升温还原等手段对催化剂进行了表征.以甲苯为模型化合物.在微型固定床反应器上评价了催化剂的催化性能.结果表明,当Cu含量较...     

N掺杂富含(001)晶面TiO_2纳米片的制备及N掺杂浓度对可见光催化活性的影响(英文)

采用水热法制备了富含(001)晶面的锐钛矿型TiO2纳米片,并通过改变热处理过程中NH3流速制备不同N掺杂浓度的TiO2纳米片.运用X射线衍射、场发射扫描电镜、高分辨率透射电子显微镜、紫外-可见漫反射光谱、X射线光电子能谱和荧光光谱对光催化剂进行了结构和性能表征,并以罗丹明B为目标降解物,考察了N掺杂浓度对TiO2纳米片可见光催化活性的影响.结果表明,NH3流速为40ml/min时制备的N掺杂TiO2纳米片具有最低的光生电子-空穴复合速率,最高的OH产生能力并表现出最高的光催化活性.同时,讨论了N掺杂浓度对TiO纳米片可见光催化活性影响的机理.     

Cu、C共负载ZnO光催化剂固氮性能及机理

为提高ZnO催化剂光催化固氮性能,克服其光生电子-空穴复合率高、可见光响应能力差以及易光腐蚀等缺点,本研究采用Cu、C共负载方式对ZnO催化剂进行改性(以下简称CuCZ催化剂)。结果显示,CuCZ?3%(Cu占ZnO质量的3%)催化剂的光催化固氮速率最大,达到4.96 mmol·g_cat^-1·h^-1,为ZnO(0.612 mmol·g_cat^-1·h^-1)的8.10倍、CZnO(C负载ZnO,3.00 mmol·g_cat^-1·h^-1)的1.65倍。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、高分辨透射电子显微镜(HRTEM)、X射线光电子能谱(XPS)、紫外可见漫反射光谱(UV?Vis DRS)、光致发光光谱(PL)以及电化学阻抗谱(EIS)对CuCZ催化剂进行表征以探究其光催化固氮效果提高的机理。结果表明,Cu、C共负载产生的界面电荷转移机制和C的“电子桥梁”作用提高了ZnO催化剂的光催化固氮性能,降低了光生电子-空穴复合率。CuCZ?3%催化剂的4次光催化循环固氮速率稳定于4.61~4.96 mmol·g_cat^-1·h^-1之间,这说明C层的包覆削弱了CuCZ催化剂的光腐蚀过程,增强了其稳定性。     

One‐Step Exfoliation and Fluorination of Boron Nitride Nanosheets and a Study of Their Magnetic Properties

A novel, simple, and efficient method for the preparation of the fluorinated hexagonal boron nitride nanosheets (F‐BNNSs) and the corresponding magnetic properties is presented. A one‐step route is used to exfoliate and fluorinate the BNNSs by ammonium fluoride (NH₄F) from hexagonal boron nitride (h‐BN) powder. Through related instrument characterizations and theoretical calculations, we confirm that large‐area and few‐layer F‐BNNSs were successfully produced by this method, which can be attributed to a fluorination‐assisted exfoliation mechanism from the bulk h‐BN in NH₄F. More intriguingly, we initially verified that the as‐prepared F‐BNNSs exhibit ferromagnetic characteristics, which would have good potential applications in spintronic devices.     

Fabrication of Hexagonal Boron Nitride Nanosheets by Using a Simple Thermal Exfoliation Process

A simple and inexpensive method to exfoliate boron nitride powder to form boron nitride nanosheets (BNNSs) with few layers was achieved by using a physically thermal process. The obtained BNNSs were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), atomic force microscopy (AFM), X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), IR spectroscopy, and Raman spectroscopy. The size distribution of the sheets and average sheet size is in the range of 80–380 nm and 200±62 nm, respectively, and the pure phase h‐BN products were confirmed. XPS result showed the B/N atomic ratio to be 0.99. In addition, the BNNSs can well disperse in aqueous solution to form a cloudy suspension and importantly, can remain suspended for 1 month without precipitate, which would have good potential in a wide range of applications.     

双金属离子调控型镍钴氧化物纳米片用于非对称超级电容器

通过水热-煅烧两步法制备了系列镍钴氧化物（NCO）纳米片。通过改变前驱体溶液中的镍、钴离子物质的量之比,进而调控NCO纳米片中的过渡金属离子比例。NCO纳米片的晶相、形貌和结构利用X射线衍射、扫描电子显微镜和X射线光电子能谱表征。此外,对NCO纳米片的电化学性能进行测试。结果表明,NCO-2（Ni_1.95Co₁O_x）纳米片在0.5 A·g^-1电流密度下,比电容为1 096.88 F·g^-1,且经过5 000次循环后具有78.26%的循环稳定性。以NCO-2为正极、活性碳为负极构成的非对称超级电容器,在功率密度为576 W·kg^-1时,能量密度为57.70 Wh·kg^-1。     

双金属离子调控型镍钴氧化物纳米片用于非对称超级电容器

通过水热-煅烧两步法制备了系列镍钴氧化物(NCO)纳米片。通过改变前驱体溶液中的镍、钴离子物质的量之比，进而调控NCO纳米片中的过渡金属离子比例。NCO纳米片的晶相、形貌和结构利用X射线衍射、扫描电子显微镜和X射线光电子能谱表征。此外，对NCO纳米片的电化学性能进行测试。结果表明，NCO-2(Ni_1.95Co₁O_x)纳米片在0.5 A·g^-1电流密度下，比电容为1 096.88 F·g^-1，且经过5 000次循环后具有78.26%的循环稳定性。以NCO-2为正极、活性碳为负极构成的非对称超级电容器，在功率密度为576 W·kg^-1时，能量密度为57.70 Wh·kg^-1。     

纳米晶态硼化钴的合成及其催化氨硼烷高效制氢

采用简单的煅烧工艺合成了纳米硼化钴(CoB)晶体,并首次研究了纳米CoB晶体在氨硼烷溶液水解制氢过程中的催化活性。研究发现,纳米CoB晶体具有较高的催化活性,在室温条件下其转换频率(TOF)为35.3 mol_H2·mol_cat^-1·min^-1,优于同等条件下贵金属Pt催化剂(TOF=29.3 mol_H2·mol_cat^-1·min^-1)。此外,循环测试8次后纳米硼化物晶体的催化制氢性能没有发生衰减。进一步研究发现CoB表面的Co⁰物种是催化制氢的活性位点,而表面的B物种位点能够有效辅助Co⁰位点实现协同催化氨硼烷制氢。     

The effect of polymer-substrate interaction on the nucleation property: Comparing study of graphene and hexagonal boron nitride Nanosheets

Hexagonal boron nitride nanosheets (BNNSs) can work as a more efficient nucleating agent for two polyesters compared to graphene. Studies on the crystallization and dewetting processes of two polyesters, poly(butylene succinate) and poly(butylene adipate), on the two substrate surfaces prove that the interaction between BNNSs and the polyesters is stronger than that between graphene and the polyesters. This strong interaction induces the pre-ordered conformation of molten PBA which has been identified by the in situ FTIR spectra. Thus BNNSs possess higher nucleation property than graphene. Finally, a new polymer-substrate interaction induced nucleation mechanism was proposed to explain the nucleation efficiency difference between graphene and BNNSs.     

A Boron Nitride Nanosheets Composite Membrane for a Long-Life Zinc-Based Flow Battery

The capability to maintain a constant system temperature is vital in nature, since it endows the system with enhanced lifetime. This trait also works for zinc-based batteries, because their cycle-life is limited by notorious zinc dendrite/accumulation, which are highly affected by the inhomogeneous distribution of temperature on electrode and relatively low mechanical strength of membrane. Herein, boron nitride nanosheets (BNNSs) with high mechanical strength serving as heat-porter are introduced onto a porous substrate to enable uniform deposition of zinc and further a zinc-based flow battery with long-cycle life. The results indicate that BNNSs can effectively adjust the deposited zinc from needle-like to French fries-like morphology, thus affording the battery with a stable performance for nearly 500 cycles at 80 mA cm⁻². Most importantly, an energy efficiency of above 80 % can be obtained even at 200 mA cm⁻², which is by far the highest value ever reported among zinc-based flow batteries.