Formation of Anatase Nanocrystals in Sol-Gel Derived TiO2-SiO2 Thin Films with Hot Water Treatment

We have successfully prepared transparent and porous anatase nanocrystals-dispersed films by treating the sol-gel derived TiO₂-SiO₂ films containing poly(ethylene glycol), PEG, with hot water. This process was done at temperatures lower than 100°C under atmospheric pressure, and thus anatase nanocrystals-dispersed films can be formed on various kinds of substrates including organic polymers with poor heat resistance. The changes in structure and composition of the TiO₂-SiO₂ gel films with hot water treatment were related to the formation process of anatase nanocrystals in the TiO₂-SiO₂ gel films with hot water treatment. The formation of anatase nanocrystals was found to proceed to hydrolysis of Si–O–Ti bonds and dissolution of SiO₂ component. In addition, porous film structure formed by leaching of PEG with hot water treatment led to homogenous dispersion of anatase nonocrystals in the films.     

Preparation and properties of SiO2-TiO2 thin films from silicic acid and titanium tetrachloride

The preparation of SiO₂-TiO₂ thin films by the sol-gel method using silicic acid and titanium tetrachloride as starting materials was studied. The homogeneous sols were obtained by the condensation reaction of silicic acid with titanium tetrachloride in methanol-tetrahydrofuran. The dipcoating of slide glasses and silicon wafers followed by heat treatment gave oxide thin films of 88–93% transmittance, 3000–4500 Å thickness, and 1.45–1.80 refractive index, depending on heat-treatment temperature and TiO₂ content. FT-IR measurement showed that the Si-O-Ti bond is formed even in the sol and films. The variations of film thickness and refractive index on transformation from the gels into the oxides were found to be quite low.     

Influences of Solvent on Properties of TiO<Subscript>2</Subscript> Porous Films Prepared by a Sol-Gel Method from the System Containing PEG

Ethanol, n-butanol, mixed ethanol/terpineol and ethanol/1-decanol were used as the solvents to prepare porous TiO₂ films by the sol-gel method from the system containing tetrabutylorthotitanate as starting material and PEG as a template. The comparison of effects of the four solvents on the porous structure, film thickness, crystallization behavior from amorphous to anatase and optical properties of the resultant TiO₂ porous films are discussed. The maximum thickness of the film prepared by one-run dip-coating reaches over 1.17 μm when 1-decanol is used as the solvent. The mechanism for formation of the porous structure is interpreted based on the phase separation and self-assembly of PEG in the sol systems.     

Preparation and Characterization of TiO2 Thin Films by Sol-Gel Method

Titanium dioxide (TiO₂) thin films have been deposited on silicon and glass substrates by the sol-gel process using titanium iso-propoxide [Ti(O-i-C₃H₇)₄]. The bond configuration of the TiO₂ thin films was analyzed by using FTIR in the wavenumber range from 400 to 4000 cm^–1. The spectral transmittance of as-deposited TiO₂ films deposited on fused silica glass was measured in the wavelength range from 200 to 900 nm. X-ray diffraction measurements were performed to determine the crystallinity of the TiO₂ films. As-deposited films were amorphous. As the film was annealed at higher temperature, the structure was transformed from amorphous to the anatase crystalline state. The chemical composition of the deposited film was investigated using X-ray photoelectron spectroscopy (XPS). The films are essentially stoichiometric with carbon as the dominant impurity on the surface. Raman spectra show the characteristic of TiO₂ anatase phase. The electrical properties of the TiO₂ films were measured using capacitance-voltage (C-V) and current-voltage techniques. From C-V measurements, the dielectric constants were calculated to be approximately 26 for the as-deposited films and 75–82 for films annealed at 700°C in different atmosphere. For the as-deposited samples, the breakdown voltage was 2.7 MV/cm, and for an electric field of 1 MV/cm, the leakage current was 5 × 10^–5 A/cm² and the resistivity was 2.2 × 10¹⁰ -cm.     

Sol-Gel Poly-Component Nano-Sized Oxide Powders

Nano-sized, amorphous and monodispersed poly-component powders in the Al₂O₃–TiO₂–MgO and Al₂O₃–TiO₂–SiO₂ systems have been obtained by the sol-gel method. These powders have been characterized by XRD, IR spectroscopy, DTA/TGA and EDAX spectrometry. This last method confirmed the composition of the ternary powders, which are formed during the gelation process.The powders were tested as precursors for obtaining advanced ceramics, as tialite, Al₂TiO₅. The samples prepared with powders obtained by sol-gel method have shown a high reactivity, and the formation of tialite was improved.     

Photocatalytic activity of TiO2 prepared by adding polyethyleneglycol

TiO₂ was produced by the sol-gel method with the addition of polyethyleneglycol (PEG) to study the effects of the molecular weight and the addition percentage of PEG. Bisphenol A (BPA) degradation rate constants were highest as 3.07, 4.02 and 4.23 h⁻¹ at PEG addition percentages of 10%, 5% and 0.5%. After 12 h reaction, the total organic carbon (TOC) reductions in UV/TiO₂, UV/TiO₂/PEG(200, 10%), UV/TiO₂/PEG(600, 5%) and UV/TiO₂/PEG(3500, 0.5%) systems were 44%, 24%, 19% and 23%, in order. The results demonstrated that adding an appropriate percentage of PEG to the TiO₂ preparation processes increased the BPA degradation and TOC reduction.     

Photocatalytic hydrogen evolution over mesoporous TiO2/metal nanocomposites

Na⁺ complex with the dibenzo-18-crown-6 ester was used as a template to synthesize mesoporous titanium dioxide with the specific surface area 130–140 m²/g, pore diameter 5–9 nm and anatase content 70–90%. The mesoporous TiO₂ samples prepared were found to have photocatalytic activity in Cu^II, Ni^II and Ag^I reduction by aliphatic alcohols. The resulting metal–semiconductor nanostructures have remarkable photocatalytic activity in hydrogen evolution from water–alcohol mixtures, their efficiency being 50–60% greater than that of the metal-containing nano-composites based on TiO₂ Degussa P25.The effects of the thermal treatment of mesoporous TiO₂ upon its photocatalytic activity in hydrogen production were studied. The anatase content and pore size were found to be the basic parameters determining the photoreaction rate. The growth of the quantum yield of hydrogen evolution from TiO₂/Ag⁰ to TiO₂/Ni⁰ to TiO₂/Cu⁰ was interpreted in terms of differences in the electronic interaction between metal nanoparticles and the semiconductor surface. It was found that there is an optimal metal concentration range where the quantum yield of hydrogen production is maximal. A decrease in the photoreaction rate at further increment in the metal content was supposed to be connected with the enlargement of metal nanoparticles and deterioration of the intimate electron interaction between the components of the metal–semiconductor nanocomposites.     

Photocatalytic Activity and Characterization of the Sol-Gel Derived Pb-Doped TiO2 Thin Films

Photocatalytically active Pb-doped TiO₂ thin films were prepared on a soda-lime glass substrate by sol-gel dip-coating technique using TiO₂ sols containing lead(II) nitrate. The thin films were characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), UV-VIS spectroscopy and X-ray diffraction (XRD). A shift of the UV-VIS absorption towards longer wavelengths was observed, which indicated a decrease in the band-gap of TiO₂ upon Pb doping. XRD results showed both pure and Pb-doped TiO₂ thin films were polycrystalline, anatase type, and oriented predominantly to the (101) plane. A slight shift in the d-spacing for the Pb-doped film indicated the incorporation of Pb into the TiO₂ lattice to form Pb _x Ti_1–x O₂ solid solution. AFM results showed Pb-doped TiO₂ thin films were composed of larger TiO₂ particles and had rougher surface, compared with un-doped TiO₂ thin films. XPS results showed that except for the enrichment of Pb near the surface, Pb exists in the forms of Pb _x Ti_1–x O₂ and PbO. Dimethyl-2,2-dichlorovinyl phosphate (DDVP) was efficiently degraded in the presence of the Pb-doped TiO₂ thin films by exposing the insecticide solution to sunlight. The mechanism of photocatalytic activity enhancement of the Pb-doped TiO₂ thin films was discussed.     

Au-TiO2/Chit modified sensor for electrochemical detection of trace organophosphates insecticides

In this paper, Au–TiO₂/Chit modified electrode was prepared with Au–TiO₂ nanocomposite (Au–TiO₂) and Chitosan (Chit) as a conjunct. The Au–TiO₂ nanocomposite and the films were characterized by electrochemical and spectroscopy methods. A set of experimental conditions was also optimized for the film's fabrication. The electrochemical and electrocatalytic behaviors of Au–TiO₂/Chit modified electrode to trace organophosphates (OPs) insecticides such as parathion were discussed in this work. By differential pulse voltammetry (DPV) measurement, the current responses of Au–TiO₂/Chit modified electrode were linear with parathion concentration ranging from 1.0 ng/ml to 7.0 × 10³ ng/ml with the detection limit of 0.5 ng/ml. In order to evaluate the performance of the detection system, we also examined the real samples successfully in this work. It exhibited a sensitive, rapid and easy-to-use method for the fast determination of trace OPs insecticides.     

Preparation of TiO2 Thin Film Photocatalysts by Dip Coating Using a Highly Viscous Solvent

TiO₂ thin film photocatalysts coated onto soda lime glass were prepared by a dip coating process using a highly viscous solvent. The source of the TiO₂ was tetraisopropyl orthotitanate, and -terpineol was used as the solvent. Two types of thin film preparation procedures based on dip coating (a sol-gel system and thermal decomposition system) were used to prepare the samples. TiO₂ thin films were obtained after calcination at 450°C for 1 hour. The film thickness obtained with a single dipping was proportional to the viscosity of the dip coating solutions. The obtained thin films were transparent with a thickness of 1 m. The crystal form of the obtained photocatalyst films was anatase alone. The thin films were formed with aggregated nano-sized TiO₂ single crystals (7–15 nm). The photocatalytic activity of the TiO₂ thin films, as evaluated by the photooxidation of NO (1 ppm) in dry air, was as high as our previous TiO₂ thin films prepared by the sol-gel method.     

UV-Visible and IR Spectroelectrochemical Studies of FeVO4 Sol-Gel Films for Electrochromic Applications

The sol-gel synthesis route, in combination with dip-coating deposition, was used for the preparation of FeVO₄ films. TEM measurements of Fe/V (1 : 1)-oxide films heated at 400°C reveal that the films consist of a triclinic FeVO₄-I and an orthorhombic FeVO₄-II phases with a grain size of up to 50 nm. The electrochromic properties of the films were tested in 1 M LiClO₄/propylene carbonate (PC) using various electrochemical techniques and in-situ UV-visible spectroelectrochemical measurements. The best compromise between the charge capacity per film thickness (Qd^–1 = –0.14 mC cm^–2 nm^–1), electrochemical stability (>1000 cycles) and optical modulation (T_vis = 0.15) was achieved in the potential range of 4.80 to 1.80 V vs. Li, which suggests that FeVO₄ films can be used as counter-electrodes in electrochromic devices.Extensive IR-spectroscopy studies of FeVO₄ films in charged/discharged states revealed the following spectra changes: (i) small charging (–0.01 mC cm^–2 nm^–1) leads to a variation in the intensity of all the vibrational bands without shifting their frequencies, (ii) higher chargings bring about the intensity and frequency changes of bridging V—O···Fe and V···O···Fe stretchings showing that vanadium, and probably also iron, are involved in the insertion/extraction processes, (iii) below 500 cm^–1 broad absorption appears due to the Li⁺—O modes, which also remained in the IR spectra of discharged (bleached) states revealing the irreversible lithiation, and (iv) charging to –0.30 and –0.50 mC cm^–2 nm^–1 leads to the amorphisation of the film structure.     

Preparation of nanocrystalline porous titania films on titanium substrates by a sol–gel method with polyethylene glycol as a template

Porous nanocrystalline TiO₂ films have been prepared on cp-Ti substrates for biomedical usage by a sol–gel process from the solutions containing polyethylene glycol (PEG) as a template. Variations of the crystal structure with heat-treatment temperature determined by XRD are different for TiO₂ films and powders, due to the effect of titanium substrate. The surface texture of porous TiO₂ films is analyzed by means of SEM and found to greatly depend on the concentration and molecular weight of PEG. The pore formation mechanism is discussed in relation to the self-assembly of PEG and phase separation between PEG adsorbed on TiO₂ oligomers and ethanol.     

TiO2–carbon nanotube heterojunction arrays with a controllable thickness of TiO2 layer and their first application in photocatalysis

TiO₂–carbon nanotube (CNT) heterojunction arrays on Ti substrate were fabricated by a two-step thermal chemical vapor deposition (CVD) method. CNT arrays were first grown on Ti substrate vertically, and then a TiO₂ layer, whose thickness could be controlled by varying the deposition time, was deposited on CNTs. Measured by electrochemical impedance spectroscopy (EIS), the thickness of the TiO₂ layer could affect the photoresponse ability significantly. About 100 nm thickness of the TiO₂ layer proved to be best for efficient charge separation among the tested samples. The optimized TiO₂–CNT heterojunction arrays displayed apparently higher photoresponse capability than that of TiO₂ nanotube arrays which was confirmed by surface photovoltage (SPV) technique based on Kelvin probe and EIS. In the photocatalytic experiments, the kinetic constants of phenol degradation with TiO₂–CNT heterojunctions and TiO₂ nanotubes were 0.75 h⁻¹ (R² = 0.983) and 0.39 h⁻¹ (R² = 0.995), respectively. At the same time, 53.7% of total organic carbon (TOC) was removed with TiO₂–CNT heterojunctions, while the removal of TOC was only 16.7% with TiO₂ nanotubes. These results demonstrate the super capability of the TiO₂–CNT heterojunction arrays in photocatalysis with comparison to TiO₂-only nanomaterial.     

Densification of Sol-Gel Thin Films by Ultraviolet and Vacuum Ultraviolet Irradiations

Structural changes in SiO₂ and TiO₂ gel films were investigated using ultraviolet (UV) and vacuum ultraviolet (VUV) irradiations. A significant compaction with dehydration of SiO₂ gel films was induced by irradiation of photons in the range of 9–18 eV. The refractive index and the shrinkage of the irradiated SiO₂ gel films were comparable to those obtained by sintering at 1000°C. Densification of TiO₂ gel films was also observed with irradiation of 5–14 eV photons. However, effects of the irradiation on TiO₂ gel were smaller that those on SiO₂ gel. The structural changes in the gel films are attributed to electronic excitations which are induced by irradiation with photons having higher energies than the bandgap of the oxides. The photo-induced effects are presumed to depend on the optical properties and structure of the gels.     

Patterning Effect of a Sol-Gel TiO2 Overlayer on the Photocatalytic Activity of a TiO2/SnO2 Bilayer-Type Photocatalyst

TiO₂ films with a thickness of 75 ± 5 nm (anatase) were formed on SnO₂-film (580 ± 80 nm) coated soda-lime glass substrates (SnO₂/SL-glass) by a sol-gel method. Although the photocatalytic activity for CH₃CHO oxidation (_ex > 300 nm) significantly exceeded that of a standard TiO₂/quartz sample, it decayed with illumination time (t) at t > 0.75 h. Stripes of anatase TiO₂ films of 40 nm in thickness and 1 mm in width were prepared on the SnO₂/SL-glass substrate in a 1-mm pitch by photolysis of an organically modified sol-gel film. The TiO₂ patterning further increased the photocatalytic activity by a factor of 4.1 as compared to the non-patterned sample, and it was also maintained at 0 < t < 2 h. The flat band potentials of the TiO₂ and SnO₂ films are determined to be –0.34 and +0.07 V (vs. SHE), respectively, at pH = 7 by the Mott-Schottky plots. On the basis of the results, the outstanding patterning effects could be rationalized in terms of the vectorial charge separation at the interface between TiO₂ and SnO₂.     

Preparation of TiO2 nanocrystalline films controlled by acetylacetone/polyethylene glycol and their photoelectric properties

TiO₂ nanocrystalline films were prepared from titanium tetra-n-butoxide modified with double hydrolysis inhibitors, acetylacetone and polyethylene glycol (PEG), in mixture of methanol and ethanol. The correlation among surface structure of the TiO₂ films, preparation conditions, and photovoltaic properties of the solar cells using the TiO₂ films was investigated. The particle size of the obtained TiO₂ films was decreased as the PEG content increased. The nanostructured films with the narrow distribution of particle size could be prepared. The amounts of adsorbed dyes for these TiO₂ films were larger than that without PEG. The performance of the solar cell fabricated using the TiO₂ film improved as the amount of the PEG increased, and the solar cell using the TiO₂ film prepared from the solution with 30 wt% PEG exhibited the highest performance.     

Ba Titanate and Barium/Strontium Titanate Thin Films from Hydroxide Precursors: Preparation and Ferroelectric Behavior

Randomly oriented ferroelectric BaTiO₃ and (Ba_0.6Sr_0.4) TiO₃ thin films on platinum coated Si (100) were prepared by a sol-gel method. The precursor solutions were derived from barium hydroxide or a mixture of barium/strontium hydroxides dissolved in acetic acid and titanium butoxide. Polarization versus applied voltage hysteresis studies indicated a remanent polarization of 3 µC/cm² and a coercive field of 43.4 kV/cm for BaTiO₃ films annealed at 800°C for 1 h. Corresponding parameters for (Ba_0.6Sr_0.4)TiO₃ films annealed at 800°C were found to be 7.2 µC/cm² and 102.7 kV/cm, respectively. Microstructural study of the surface morphology of these films indicated grains of less than 0.1 µm in size. The leakage current for (Ba_0.6Sr_0.4)TiO₃ films was found to be two orders of magnitude lower than that for BaTiO₃ films.     

Sol-gel coatings of BaO-TiO2-SiO2 compositions

New alkali resistant BaO-TiO₂-SiO₂ coatings have been developed via the sol-gel process. In the solutions and in the gels (T<300°C) an infrared absorption band at 930 cm^–1 gives the possible evidence of mixed Si-O-Ti bonds, which have not been found in the system SiO₂-TiO₂-ZrO₂. Baking the films at about 500°C for less than 1 h leads to stable layers with negligible residual carbon contents. Compositions near 20 BaO-40 TiO₂-40 SiO₂ showed the best performance.     

Low temperature CO oxidation on Au/TiO2 sol-gel catalysts

A comparative study on Au/TiO₂catalysts prepared by impregnation with HAuCl₄of commercial TiO₂ or by impregnation of sol-gel derived TiO₂has been carried out during CO oxidation. Specific surface areas and mean Au particle of 49 and 74 m²/g and 35 and 25 Å were obtained for impregnated commercial TiO₂ and sol-gel preparations, respectively. XRD patterns shown that in sol-gel derived TiO₂ only anatase phase was identified, while in commercial TiO₂ anatase and rutile phases co-exist. Titania support effect on Au activity for the oxidation of CO has been observed. The light-off during the reaction on Au/TiO₂initiates at 50°C, whereas for commercial impregnated TiO₂ catalyst the light-off initiates at 200°C.     

Preparation of Titanium Oxide Layer on Silica Glass Substrate with Titanium Naphthenate Precursor

Nanocrystalline TiO₂ thin films on silica glass substrates were prepared by using a naphthenic acid precursor. As-deposited thin films were heat treated at 500, 600, 700 and 800^∘C for 30 min in air. The TiO₂ thin films were analyzed by High Resolution X-ray diffraction, ultra violet—visible—near infrared spectrophotometer, field emission—scanning electron microscope and scanning probe microscope. After annealing at 600 and 700^∘C, the XRD patterns consist of only anatase peaks of TiO₂ film. Rutile(110) peak begins to appear at an annealing temperature of 800^∘C. Relative high transmittance at visible range was obtained for all films except the film annealed at 800^∘C. Optical band gap, E_g, is in the range between 3.53 and 3.78 eV except the TiO₂ film annealed at 500^∘C. The best hydrophilicity was achieved with a high-temperature annealing.