两段变温法水热合成多级孔ZSM-5分子筛及其催化裂化性能（英文）

以四丙基氢氧化铵(TPAOH)为单一模板剂,采用低温老化、高温晶化2段变温法合成出了球状多级孔ZSM-5分子筛。利用XRD、FT-IR、NH_3-TPD、SEM、TEM以及氮气吸-脱附等测试对合成样品进行了表征。结果表明:直径约为2μm左右的球状多级孔ZSM-5分子筛颗粒内的晶间介孔和大孔主要由棒状纳米晶堆积而成的,该产品具有较大的比表面积和介孔孔容。同常规水热法一步合成的微孔ZSM-5分子筛相比,2段变温法合成的多级孔ZSM-5分子筛具有更高的B酸/L酸比例(C_(BP)/C_(LP))、强酸/弱酸比例(C_s/C_w)以及活性位可接近性指数(ACI)。催化裂化评价结果显示,得益于活性位可接近性指数等指标的提高,球状多级孔ZSM-5分子筛比常规合成的微孔ZSM-5分子筛具有更高的转化率和丙烯收率等优异的催化性能。     

具有纳米线镶嵌结构ZSM-5/L复合分子筛的合成及表征

采用两步晶化法,以四丙基氢氧化铵预处理ZSM-5为晶种,快速合成了纳米线镶嵌结构ZSM-5/L复合分子筛.通过XRD、SEM-EDX、TEM和N₂吸附-脱附等手段对合成样品的物理化学性质进行了表征.孔道性质表明复合分子筛具有微孔和介孔的多级孔道结构,椭球的L分子筛镶嵌在纳米线的ZSM-5分子筛周围.晶种预处理影响了溶胶的电荷及分子筛的形貌,当合成样品中ZSM-5的质量分数小于2%（重量百分比）时,凝胶的负电荷较多,易形成椭球状L分子筛;当合成样品中ZSM-5的质量分数大于2%（重量百分比）时,zeta电位在-39.822~-42.352 mV之间波动,ZSM-5分子筛的形貌从长条状逐渐转变为纳米线状.阳离子比影响复合分子筛中L分子筛形成,当阳离子比R=n（K₂O）/（n（K₂O）+n（Na₂O））小于0.6时,不利于L型分子筛的形成;当阳离子比大于0.6,即K⁺较多Na⁺较少时,有利于L型分子筛中α-钙霞石笼的形成.     

晶种导向干凝胶法制备成型ZSM-5分子筛

在干凝胶法制备ZSM-5 分子筛的体系中添加晶种导向剂, 控制分子筛的生长, 制备了纳米沸石组装的无粘结剂成型多级孔ZSM-5 分子筛, 一步完成纳米分子筛的制备及组装成型, 即克服了传统纳米粒子难以过滤分离的问题, 同时组装所形成的多级孔有助于改善分子在催化剂内的扩散, 从而提高催化反应效率. 以硅胶、薄水铝石为原料, 四丙基氢氧化铵(TPAOH)和ZSM-5 晶种导向胶作为粘结剂, 通过混捏、挤条得到直径2 mm的条状前驱物, 随后通过干凝胶转换法制备成型分子筛. 所用晶种导向剂组成为0.35TPAOH:1SiO₂:20H₂O:4C₂H₅OH. 通过X射线衍射(XRD), 热重(TG)分析和傅里叶变换红外(FTIR)光谱等方法对分子筛晶化过程进行了表征, 结果表明晶种导向剂加入量对分子筛生长速度及多级孔结构均有影响. 当所加晶种导向剂中TPAOH与SiO₂的摩尔比为0.025时, 经过3 h晶化, 分子筛相对结晶度达到100%. 扫描电镜(SEM)结果表明, 合成的分子筛尺寸约为200 nm, 组装形成的多级孔分子筛的介孔体积为0.28 cm³·g^-1. 通过NH₃ 程序升温脱附(NH₃-TPD)考察了所得成型分子筛的酸性, 发现该分子筛酸性与市售的粉末H-ZSM-5分子筛类似.     

晶种导向下干胶法合成ZSM-5分子筛

以廉价水玻璃为硅源,在晶种替代有机模板剂的条件下采用干胶法合成了ZSM-5分子筛。利用XRD、SEM、TEM、FTIR、N₂吸附-脱附和NH₃-TPD等分析方法对合成样品进行了表征和测试,考察了合成条件对ZSM-5分子筛晶化过程的影响。结果表明,在硅铝比（n/n）为30~70,钠硅比（n/n）为0.12~0.20时都可以得到结晶度良好的ZSM-5分子筛。研究发现,干胶法合成ZSM-5,在不引入外加水的情况下也可以得到ZSM-5样品,外加水的引入能够有效地提高晶化速率;与水热法合成ZSM-5分子筛相比,干胶法可以显著地缩短晶化时间,同时,合成样品的晶体尺寸也有所减小。     

多级孔ZSM-5分子筛: 丰富的外表面酸中心和良好的二甲苯异构化催化性能

多级孔沸石分子筛的结构性质及其催化性能是近年来分子筛研究的热点.本文采用蒸汽辅助晶化的方法制备了多级孔ZSM-5沸石分子筛,采用NH₃程序升温脱附和原位吸附红外光谱等方法研究了其表面酸性质,用邻二甲苯异构化反应考察了其催化性能.结果表明,多级孔结构分子筛的结晶度和总酸量有所下降,但Lewis酸中心却有所增加.进一步研究发现,多级孔结构分子筛的外表面酸中心数量远高于常规分子筛,从而证实了多级孔结构可以将更多的酸中心暴露到外表面;而外表面酸中心数量的增多和扩散传质的改善是多级孔ZSM-5分子筛在邻二甲苯异构化反应中具有更高催化活性和对二甲苯产率的重要原因.     

系列硅铝比纳米薄层ZSM-5分子筛的合成和表征

以自制不对称双子季铵盐表面活性剂为模板, 在水热合成体系中控制合成系列硅铝比纳米薄层ZSM-5分子筛.采用X射线衍射(XRD)、N₂吸附-脱附、X射线荧光光谱(XRF)、扫描电镜(SEM)和²⁷Al魔角旋转核磁共振(²⁷Al MAS-NMR)对合成的样品进行了表征. 详细研究了晶化温度、晶化时间、结构导向剂(SDA)用量、碱度等对合成的影响和纳米薄层ZSM-5分子筛的形成过程. 结果表明: 分子筛硅铝比越高, 结构导向剂用量越大, 所需的晶化时间越短; 晶化温度越高, 晶化时间越短; 且不同硅铝比纳米薄层ZSM-5分子筛的形貌规整度、比表面积和介孔/微孔孔容比例随着硅铝比而变化.     

微孔/介孔复合分子筛的合成及其对CO2的吸附性能

采用两步晶化法将合成的沸石前驱液(S)或沸石固体粉末(P)经不同浓度(c)的NaOH处理后, 分别以表面活性剂十六烷基三甲基溴化铵(CTAB)软模板或介孔炭(Meso-C)硬模板为导向剂, 自组装合成S-β-MCM41(c)、P-β-MCM41(c)、P-ZSM-MCM41(c)、P-ZSM-C系列微孔/介孔复合分子筛. 考察了沸石分子筛种类、碱处理液浓度以及介孔模板剂对合成复合分子筛结构与性能的影响. X射线衍射(XRD)、透射电子显微镜(TEM)和氮气吸附-脱附表征结果表明产物具有微孔/介孔多级孔结构. 该材料对CO₂的吸附能力比纯微孔或介孔材料均有明显提高, 其中P-ZSM-MCM41(2)的CO₂吸附容量最大可达1.51 mmol·g^-1, 为ZSM-5沸石吸附量的两倍多.     

一种合成高水热稳定性微孔-介孔复合分子筛β沸石/MCM-41的新方法

首次以β沸石作为硅铝源制备了β沸石/MCM-41微孔-介孔复合分子筛材料，通过XRD、IR、N₂吸附脱附、SEM和水热处理等手段对复合材料进行了表征，并与MCM-41和β沸石及二者的机械混合物的有关性能进行了对比研究。结果表明，复合分子筛明显不同于机械混合物，其水热稳定性远远高于普通方法合成的介孔分子筛，而且发现通过改变体系的n_Na/n_Si比，可以调变复合样品中的微孔、介孔相的相对含量。     

高岭土微球上无胺法ZSM-5的原位合成

无胺体系中,采用水热法在焙烧高岭土微球上原位晶化合成了ZSM-5分子筛。考察了晶化温度、晶化时间、晶种加入量以及合成体系硅铝比等主要因素对分子筛合成的影响,得出了较佳的原位晶化合成条件。采用XRD、SEM、N₂吸附脱附等手段对合成样品进行了表征。结果表明：在高岭土微球上合成出了颗粒尺寸小于1 μm的小晶粒原位ZSM-5分子筛;晶化产物的比表面积、总孔容、微孔表面积和微孔孔容均明显增大,微孔分布集中于0.54 nm。     

碱处理浓度对预脱铝ZSM-5成孔过程及其MTG反应性能的影响

在80℃水浴条件下,对ZSM-5分子筛进行酸碱处理改性;重点考察了碱处理溶液浓度对酸预处理脱铝后ZSM-5分子筛微观结构及其催化甲醇制汽油(MTG)性能的影响。通过BET、XRD、FT-IR、NH₃-TPD和TEM等手段对样品进行表征。结果表明,单独酸处理没有改变分子筛孔结构,单独碱处理产生了并不明显的介孔。酸预处理后再碱处理可促进介孔的产生,产生更为显著的介孔结构;而且随着碱处理强度的增加,分子筛样品的介孔/微孔比表面积比例和孔体积均先增大后降低。酸浓度2mol·L^-1,碱浓度0.4mol·L^-1条件处理得到的分子筛,介孔比表面积比例和孔容均达到最大,酸量和酸强度最低。在400℃,0.1MPa,WHSV=2.1h^-1条件下,甲醇制汽油反应性能最佳:汽油收率由未改性时的30wt%提高到34wt%,寿命更是由16h延长到135h,芳烃含量由原来的73wt%降至20wt%。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.