Functional Nickel Oxide Nanostructures for Ethanol Oxidation in Alkaline Media

Nickel oxide (NiO) nanostructures are employed in the basic medium for the oxidation of ethanol. A variety of NiO nanostructures are synthesized by wet chemical growth method, using different hydroxide (OH^?) ion sources, particularly from ammonia, hexamethylenetetramine, urea and sodium hydroxide. The use of urea as (OH^?) ion source results in flower‐like NiO structures composed by extremely thin nanowalls (thickness lower than 10 nm,), which demonstrated to be the most active for ethanol oxidation. All the samples exhibit NiO cubic phase, and no other impurity was detected. The cyclic voltammetry (CV) curves of NiO nanostructures were found linear over the concentration range 0.1–3.5 mM (R²=0.99) of ethanol, with the limit of detection estimated to be 0.013 mM for ethanol. The NiO nanostructures exhibit a selective signal towards ethanol oxidation in the presence of different members of alcohol family. The proposed NiO nanostructures showed a significant practicality for the reproducible and sensitive determination of ethanol from brandy, whisky, mixture of brandy and rum, and vodka samples. The nanomaterial was used as a surface modifying agent for the glassy carbon electrode and it showed a stable electro‐oxidation activity for the ethanol for 16 days. These findings indicate that the presented NiO nanomaterial can be applied in place of noble metals for ethanol sensing and other environmental applications (like fuel cells).     

Ultra‐sensitive Amperometric Hydrazine Sensing via Dimethyl Glyoxomat Derived NiO Nanostructures

Here we report the synthesis of NiO nanostructures via glyoxomat assisted precipitation protocol using hydrothermal route under the influence of ammonia followed by annealing at 450 ^oC. These nanostructures were characterized via Scanning Electron Microscopy (SEM) and X‐ray Diffraction (XRD) method. The morphological investigation of the finally prepared NiO revealed foam‐like porous nanostructures. These NiO nanostructures were immobilized onto glassy carbon electrode (GCE) with nafion as binding material and used as highly sensitive and selective sensor for determining hydrazine in the range of 100–500 nM and 600–1600 nM with a calculated limit of detection (LOD) equal to 5 nM. The as prepared sensor was tested for the presence of various interfering species such as Na⁺, Cu²⁺, uric acid, hydrogen peroxide and glucose in the presence of equimolar concentration of hydrazine and negligible interference was noticed. The sensor was further tested for hydrazine detection using square wave voltammetry (SWV) however it only worked in the range of 50–1200 μM. Finally the sensor was successfully implemented for hydrazine determination in real water samples using amperometric protocol.     

Polyaniline-ZnO−NiO Nanocomposite Based Non-enzymatic Electrochemical Sensor for Malathion Detection

An electrochemical sensor based on polyaniline-ZnO−NiO (PANI-ZnO−NiO) nanocomposite was developed for the non-enzymatic detection of malathion. The structure, surface morphology, and optical properties of the as-prepared nanocomposite were studied by XRD, FTIR, SEM, and UV-Vis spectroscopy. The electrochemical behavior of the nanocomposite based sensor was first evaluated through cyclic voltammetry (CV). Under optimum conditions, differential pulse voltammetry (DPV) was further utilized for malathion detection, which proved the PANI-ZnO−NiO/GCE electrode as an effective electrochemical sensor. The developed electrochemical sensor showed a low detection limit of 1.0×10⁻⁸ M with a wider linear range of 10 to 70 nM for malathion.     

表面等离子体共振技术与循环伏安法联用检测甲苯胺蓝

将表面等离子体共振技术(SPR) 与循环伏安法(CV) 联用, 并用小波变换提取实验数据, 实现了甲苯胺蓝的定量检测. 以传感片上的金膜为SPR测量基底, 并作为电化学的工作电极, 以Ag/AgCl电极(饱和KCl) 为参比电极, 以铂丝为对电极, 同时进行SPR扫描和循环伏安法扫描, 发现电化学聚合导致甲苯胺蓝氧化峰峰电位正移, 还原峰峰电位不变, 而SPR响应也整体下降; 将SPR响应对电位求导后进而对电位作图, 经小波变换处理后, 发现波谱峰电位接近循环伏安法氧化还原法电位. 利用该方法检测甲苯胺蓝的检出限与采用循环伏安法检测甲苯胺蓝的检出限在一个数量级上.     

Carbon Quantum Dots Co‐catalyzed with ZnO Nanoflowers and Poly (CTAB) Nanosensor for Simultaneous Sensitive Detection of Paracetamol and Ciprofloxacin in Biological Samples

A novel platform based incorporation of carbon quantum dots (CQDs) and zinc oxide nanoflowers (ZnO‐NFs) decorated with poly cetyltrimethylammonium bromide (CTAB) was developed as electrochemical sensor for the sensitive and selective simultaneous detection of Paracetamol (PAR) and Ciprofloxacin (CIP) in biological samples. For this, CQDs and ZnO‐NFs were first deposited on a glassy carbon electrode (GCE) and subsequently a Poly (CTAB) layer was grown onto their surfaces through electro‐polymerization. The synthesized nanostructures and the corresponding fabricated sensor were characterized by the techniques of TEM, XRD, FE‐SEM, and EDX analysis. Moreover electrochemical characterization by CV and DPV were performed to elucidate the construction process and electron transfer abilities of the CQDs/ZnO‐NFs/Poly(CTAB)/GCE. Increased sensitivity and efficiency of this sensing system was obtained due to the synergistic effects of CQDs, ZnO‐NFs and Poly (CTAB) with multi‐signal amplification. Under the optimum conditions, the DPV response of proposed sensor to PAR and CIP was linear at 0.05–30.0 μM and 0.01–30.0 μM, with the detection limit of 2.47 nM and 1.97 nM respectively. The sensor possessed high stability, reproducibility, sensitivity, and selectivity toward PAR and CIP detection, over potential interferents and presented high recovery percentage in the real sample matrices.     

Facile Green Synthesis of NiO/NiCo2O4 Nanocomposite as an Efficient Electrochemical Platform for Determination of Dopamine

The synthesis of NiO/NiCo₂O₄ nanoparticles by an eco-friendly, fast, simple and cost-effective approach employing Urtica extract is reported in this study. The NiO/NiCo₂O₄ nanocomposite were characterized using VSM, FTIR, XRD, and SEM techniques. Moreover, to construct a modified carbon paste electrode, NiO/NiCo₂O₄ were employed and this sensor was used for dopamine (DA) detection. Using cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques, the electrochemical behavior of dopamine at the NiO/NiCo₂O₄/CPE was investigated. Analysis of dopamine, with a limit of detection (LOD) equal to 0.04 μM, in the concentration range of 0.1–100.0 μM, was facilitated by NiO/NiCo₂O₄/CPE. Moreover, the satisfactory selectivity for DA determination in the presence of uric acid (UA) and ascorbic acid (AA), was obtained. The suggested new sensor displayed a good reproducibility, sensitivity, and stability for determination of DA in drug and biological samples.     

Sensitive and Green Method for Determination of Chemical Oxygen Demand Using a Nano‐copper Based Electrochemical Sensor

Copper nanoparticles (nano‐Cu) were electrodeposited on the surface of glassy carbon electrode (GCE) potentiostatically at −0.6 V vs. Ag/AgCl for 60 s. The developed nano‐copper modified glassy carbon electrode (nano‐Cu/GCE) was optimized and utilized for electrochemical assay of chemical oxygen demand (COD) using glycine as a standard. The surface morphology and chemical composition of nano‐Cu/GCE were investigated using scanning electron microscope (SEM) and energy dispersive X‐ray spectrometer (EDX), respectively. The electrochemical behavior was investigated using linear sweep voltammetry (LSV) which is characterized by a remarkable anodic peak at ∼0.6 V, compared to bare GCE. This indicates that nano‐Cu enhances significantly the electrochemical oxidation of glycine. The effect of different deposition parameters, such as Cu²⁺ concentration, deposition potential, deposition time, pH, and scan rate on the response of the developed sensor were investigated. The optimized nano‐Cu/GCE based COD sensor exhibited a linear range of 15 to 629.3 ppm, and a lower limit of detection (LOD) of 1.7 ppm (S/N=3). This developed method exhibited high tolerance level to chloride ion (0.35 M chloride ion has minimal influence). The analytical utility of the prepared COD sensor was demonstrated by investigating the COD recovery (99.8±4.3) and the assay of COD in different water samples. The results obtained were verified using the standard dichromate method.     

High-yield synthesis of pure ZnO nanoparticles by one-step solid-state reaction approach for enhanced photocatalytic activity

Zinc oxide (ZnO) nanostructures were synthesized via a one-step solid-state reaction approach in ammonia (NH₃) gas environment with different temperature ramp rates. The so-formed nanostructures were characterized using X-ray diffraction (XRD) for phase identification, where the typical wurtzite hexagonal structure was observed. Scanning electron microscopy (SEM) confirmed the particle size to be in the range 45–50 nm, the same as calculated by the XRD pattern for the ramp rate of 10 °C/min. Energy dispersive X-ray (EDX) spectroscopy and X-ray photoelectron spectroscopy (XPS) confirmed the chemical purity of the samples. The photoluminescence (PL) spectrum indicated multiple near-band-edge emissions and energy-band emissions. Then, these ZnO nanomaterials were used for the degradation of crystal violet (CV) dye under UV light irradiation. The CV solution was completely degraded in 2 hr. The initial photocatalyst and dye amounts of 0.2 g/100 ml and 0.5 mg/L, respectively, were found to be the optimum values for maximum degradation efficiency. The ZnO-based photocatalyst was stable up to three cycles of reuse. These results indicate that the high surface area and porosity of the nanomaterials are responsible for the high efficiency, which was confirmed by specific surface area analysis.     

Hydrothermal synthesis and pseudocapacitance properties of MnO2 nanostructures

The effect of varying the hydrothermal time to synthesize manganese oxide (MnO(2)) nanostructures was investigated along with their influence on structural, morphological, compositional, and electrochemical properties in supercapacitor electrode materials. XRD and TEM studies showed that the MnO(2) prepared in shorter hydrothermal dwell time was a mixture of amorphous and nanocrystalline particles, and there was an evolution of crystallinity of the nanostructures as the dwell time increased from 1 to 18 h. Interestingly, SEM, TEM, and HRTEM revealed a variety of structures ranging from nanostructured surface with a distinct platelike morphology to nanorods depending upon the hydrothermal reaction time employed during the preparation of the manganese oxide: increasing the amount of individual nanorods in the materials prepared with longer hydrothermal reaction time. The surface area of the synthesized nanomaterials varied from 100 to 150 m(2)/g. Electrochemical properties were evaluated using cyclic voltammetry (CV) and galvanostatic charge-discharge studies, and the capacitance values were in the range 72-168 F/g depending upon synthesis conditions. The formation mechanism of the nanorods and their impact on the specific capacitance were discussed in detail.     

OH functionalized Multi-Walled Carbon Nanotube modified electrode as electrochemical sensor for the detection of Aceclofenac

ABSTRACT

The rapid electrochemical determination of Aceclofenac (ACF) has been employed by cyclic voltammetry (CV), differential pulse voltammetry (DPV) using developed OH-functionalised multiwalled carbon nanotube carbon paste electrode (OH-MWCNT/CPE). Modified electrode was characterised by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDAX), X-ray diffraction spectroscopy (XRD), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The ACF exhibits two oxidation peaks at +0.4 V, +0.66 V and one reduction peak at +0.3 V. The active surface area of the bare carbon paste electrode (BCPE) and modified electrode have been characterised by using K₃[Fe(CN)₆] solution containing 0.1 M KCl. In DPV mode, variation of ACF gave the limit of detection (LOD = 3s/m) 0.246 μM over the concentration range 1.0 to 190.0 μM (R² = 0.9994). The developed electrode has good stability, reproducibility and could be successfully validated for the detection of ACF in pharmaceutical samples and biological fluids.     

Design and Development of a Non-Enzymatic Electrochemical Biosensor for the Detection of Glutathione

Glutathione (GSH-reduced form) is a tripeptide that plays a vital role as an antioxidant to remove xenobiotics in the human body and changes in GSH levels are a marker for the progression of various diseases. In this context, a highly sensitive non-enzymatic electrochemical biosensor for the detection of GSH has been developed using reduced graphene oxide Manganese oxide (rGMnO) nanocomposite as the nano-interface. Initially, graphene oxide was synthesized by Hummer's method and then thermally reduced in the presence of MnO₂ in a blast furnace to obtain rGMnO nanocomposite. The nanocomposite was characterized to validate its structure and morphological properties via Scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman, and X-ray photoelectron spectroscopy (XPS). Cyclic voltammetry and amperometry studies showed that upon the addition of GSH, the Pt/rGMnO modified working electrode exhibited a linear response in the range of 1–100 μM at an input voltage of −0.62 V. The developed sensor was found to have a sensitivity of 0.3256 μA μM⁻¹ and LOD of 970 nM with a recovery of 92–104 % in real blood serum samples.     

Construction of an electrochemical sensor based on the electrodeposition of Au-Pt nanoparticles mixtures on multi-walled carbon nanotubes film for voltammetric determination of cefotaxime

Mixtures of gold-platinum nanoparticles (Au-PtNPs) are fabricated consecutively on a multi-walled carbon nanotubes (MWNT) coated glassy carbon electrode (GCE) by the electrodeposition method. The surface morphology and nature of the hybrid film (Au-PtNPs/MWCNT) deposited on glassy carbon electrodes is characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) techniques. The modified electrode is used as a new and sensitive electrochemical sensor for the voltammetric determination of cefotaxime (CFX). The electrochemical behavior of CFX is investigated on the surface of the modified electrode using linear sweep voltammetry (LSV). The results of voltammetric studies exhibited a considerable improvement in the oxidation peak current of CFX compared to glassy carbon electrodes individually coated with MWCNT or Au-PtNPs. Under the optimized conditions, the modified electrode showed a wide linear dynamic range of 0.004-10.0 μM with a detection limit of 1.0 nM for the voltammetric determination of CFX. The modified electrode was successfully applied for the accurate determination of trace amounts of CFX in pharmaceutical and clinical preparations.     

新型锂离子电池三维结构泡沫NiO电极的制备及电化学性能

通过固相氧化方法,以三维结构泡沫镍为基体和金属镍源,制备了三维结构泡沫氧化镍负极。XRD和SEM结果表明,经500℃氧化处理,泡沫镍基体上形成了NiO微米级的致密活性氧化层。通过充放电测试和循环伏安测试研究了电极的电化学性能,结果表明,三维结构泡沫氧化镍在放电电位区间0.05～3.2VvsLi/Li+,0.2C倍率下充放电,初始容量损失为20%,且经40次循环后,质量比容量为950mAh·g-1,三维泡沫氧化镍电极具有优异的循环容量保持性能。三维泡沫氧化镍具有的大的活性表面积,降低了界面反应的极化,从而提高了NiO电极的倍率放电性能。     

Electrocatalytic Determination of the antibiotic Levofloxacin using modified carbon paste electrode with a poly-murexide thin film voltammetrically

In this work, a simple, cheap, sensitive, and selective modified carbon paste electrode is proposed for the electroanalytical determination of Levofloxacin (LEVO), the drug used to treat pneumonia caused by coronavirus. The electrochemical polymerization method was applied to create a thin poly-murexide film (POMUR) on the bare carbon paste electrode (BCPE) surface to enhance its electrocatalytic activity. The peak current response of LEVO obtained by POMUR/CPE was increased by 14.2 μA compared to BCPE. Scanning electron microscopy (SEM) and cyclic voltammetry (CV) techniques were employed to characterize BCPE and POMUR/CPE. Under the optimal experimental circumstances, the prepared sensor was capable of determining LEVO with a low limit of detection (LOD) of 7.18 nM (S/N = 3) for a linear dynamic range of 25 – 1 × 10³ nM utilizing differential pulse voltammetry (DPV). Moreover, the practical applicability of POMUR/CPE for determining LEVO in pharmaceutical formulations and biological samples (human serum) demonstrated high sensitivity and selectivity with a recovery of 95.08 – 100.5 %.     

Nickel oxide nanoparticles decorated graphene quantum dot as an effective electrode modifier for electrocatalytic oxidation and analysis of clozapine

In the present work, a novel, simple, and sensitive clozapine (CLZ) sensor was developed based on nickel oxide nanoparticle (NiO)-decorated graphene quantum dot (GQD)-modified glassy carbon electrode (NiO/GQD/GCE). NiO/GQD/GCE was prepared by simple electrodeposition, the electrochemical behavior of CLZ at the surface of the prepared electrode was studied by cyclic voltammetry (CV) and differential pulse voltammetry (DPV), and an improved reversibility and increased peak current with negative shift in the oxidation potential were observed at the proposed electrode. The effect of some experimental parameters has been examined, and based on the results, an electron transfer–chemical reaction–electron transfer mechanism has been proposed for CLZ electrooxidation. The differential pulse voltammetric response of the NiO/GQD/GCE was linear to the concentration of CLZ in the range of 3?×?10^?9 to 1?×?10^?6 M, and the detection limit was found to be 0.55 nM (S/N?=?3). The method has been successfully used for the selective determination of the CLZ amount in the pharmaceutical preparations and human serum samples with good accuracy and precision.     

β-Cyclodextrin PAMAM Dendrimer Surface Doped with Silver and Hexacyanoferrate (III) and its Applications for Dopamine Detection in Synthetic Samples

A synthesis of β-cyclodextrin (β-Cd) functionalized with polyamide dendrimer PAMAM G.0 complexed with silver and potassium hexacyanoferrate (III) forming a mixed-valence complex (β-Cd-PAMAM-Ag/Fe) was proposed. This material was characterized by scanning electron microscopy (SEM), infrared spectroscopy (FT-IR), X-Ray diffraction (XRD), Energy Dispersion Spectroscopy (EDS) and Electron Paramagnetic Resonance (EPR). The hybrid complex was electrochemically investigated using cyclic voltammetry and some parameters (electrolyte, concentration of electrolyte, pH and scan rate) were evaluate in order to obtain optimum analytical responses. The β-Cd-PAMAM-Ag/Fe material was successfully applied in the electrocatalytic oxidation of dopamine (DOP) using Cyclic Voltammetry (CV) and Square Wave Voltammetry (SWV).     

Fabrication,characterization of polyaniline intercalated NiO nanocomposites and application in the development of non-enzymatic glucose biosensor

Determination of glucose plays very important part in diagnostics and management of diabetes. Nowadays, determination of glucose is necessary in human health. In order to develop the glucose biosensor, polymer modified catalytic composites were fabricated and used to detect glucose molecules. In this work, NiO nanostructure metal oxide (NMO) was fabricated via thermal decomposition method and polyaniline (wt% = 2, 4 and 6) assisted nanocomposites (NiO/PANI) were also prepared. The morphology and structure of synthesized nanocomposites were characterized by UV–visible diffusion reflectance spectroscopy (UV–vis-DRS), Fourier transform- infra red spectroscopy (FT-IR), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HR-TEM), X-ray photoelectron spectroscopy (XPS) and N₂ adsorption-desorption isotherm measurement. The modified NiO/6%PANI/GCE had higher catalytic activity toward the oxidation of glucose than NiO/GCE, PANI/GCE, NiO/2%PANI/GCE and NiO/4%PANI/GCE. This is due to the larger surface area of NiO/6%PANI nanocomposites provide a ploform for faster electron transfer to the detection of glucose. The constructed glucose biosensor have been exhibited a high sensitivity of 606.13 µA mM⁻¹ cm⁻², lowest detection limit of 0.19 µM, high selectivity, stability, simplicity and low cost for the quick detection of glucose in real sample as well.     

Preparation and Electrocatalytic Activity of Polyaniline-poly（propylene oxide）

A novel copolymer of polyaniline-poly(propylene oxide) (PAN-PPO) was prepared by cyclic voltammetry (CV) and characterized by FFIR and SEM. It showed good electroactivity for methanol oxidation in H2SO4 solution.     

不同结构及氮掺杂NiO/rGO氧还原催化剂的制备与性能研究

本文以还原氧化石墨烯（rGO）为载体制备了片状NiO/rGO和球形NiO/N-rGO结构的氧还原催化剂. 通过X-射线衍射（XRD）、Raman（拉曼）测试、X-射线光电子能谱（XPS）、扫描电子显微镜（SEM）和透射电子显微镜（TEM）等方法表征了两种催化剂的结构和形貌. 采用循环伏安法（CV）、Tafel曲线、线性扫描伏安法（LSV）、旋转圆盘电极（RDE）和旋转环盘电极（RRDE）等技术测试研究了两种催化剂的电化学催化氧还原性能. 研究结果表明,球形NiO/N-rGO催化剂催化氧还原的峰电流密度和起始电位（0.89 V vs. RHE）与商业化的Pt/C（20%）催化剂相近. 旋转圆盘电极（RDE）和旋转环盘电极（RRDE）测试证明,在碱性电解液中NiO/rGO和NiO/N-rGO催化的氧还原反应均主要通过4?鄄电子途径反应途径发生,球形NiO/N-rGO催化剂展现出替代Pt/C基催化剂的潜力.     

模板法制备的掺镧氧化镍多孔空心微球及电化学电容性能

采用模板法在水热条件下合成了掺La的NiO多孔空心球。采用X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电镜(SEM)、透射电子显微镜(TEM)和X射线能谱(EDS)对其结构和形貌进行了表征。采用循环伏安、恒流充放电技术对其电化学性能进行了测试,研究结果表明,La掺杂对NiO空心球的粒径、壳层厚度和电化学性能均有显著影响,当La掺杂量为1.30mol%时,掺杂后NiO的单电极比电容达到205 F.g-1,比未掺杂的提高了50%,并且表现出良好的循环稳定性和可逆性。