金属纳米颗粒的制备及其在酶生物传感器中的应用研究

近年来,金属纳米颗粒的制备研究引起了人们的广泛兴趣.与相应的块体材料相比,金属纳米颗粒具有独特的化学和物理性质,可应用于电学、催化、磁性材料、光催化、生物染色剂、药物输送等许多领域.其中,传感器是纳米颗粒最有前途的应用领域之一.传感器的微型化是传感器发展的主要研究方向,将纳米颗粒用于传感器的研究将促进这一目标的实现.本论文利用纳米颗粒材料的独特效应来提高葡萄糖传感器的响应电流.将自制的银金、铂以及二氧化硅和铂复合纳米颗粒用于固定化酶,使酶电极的电流响应值得到了大幅度的提高,从而为纳米增强的新型葡萄糖生物传感器的研究、制备和应用提供了可供参考的实验和理论依据,并为传感器的小型化开辟了一条新途径.     

纳米颗粒增强的葡萄糖生物传感器

研制的纳米增强葡萄糖传感器是用纳米憎水Ａｕ颗粒。亲水Ａｕ颗粒、憎水ＳｉＯ_２颗粒以及Ａｕ和－ＳｉＯ_2颗粒混合与聚乙烯醇缩丁醛（ＰＶＢ）构成复合固酶膜基质,用溶胶－凝胶法固定葡萄糖氧化酶（ＧＯＤ）,组成葡萄糖生物传感器．实验表明,纳米颗粒可以大幅度提高固定化酶的催化活性,响应电流从相应浓度的几十纳安增强到几千纳安,电极响应迅速, １ｍｉｎ达到稳态,探讨了纳米颗粒效应在固定化酶中所起的作用,开辟了制备直接电子传递第三代生物传感器的新途径和纳米颗粒应用的新领域。     

亲水金和憎水二氧化硅纳米颗粒对葡萄糖生物传感器响应灵敏度的增强作用

用亲水金、憎水二氧化硅纳米颗粒固定葡萄糖氧化酶(GOD),采用聚乙烯醇缩丁醛(PVB)为辅助固酶膜基质来制备葡萄糖生物传感器,并考察了亲水金、憎水二氧化硅纳米颗粒对酶电极电流响应的影响.实验表明,引入纳米粒子可显著增强电极响应灵敏度.并对两种不同性质纳米颗粒所起作用的可能机理进行讨论,从理论和实验上证明了纳米颗粒对固定酶的作用.为制备有实用价值的葡萄糖生物传感器提供了可供参考的实验和理论依据.     

亲水金和憎水二氧化硅纳米颗粒对葡萄糖生物传感器响应灵 …

用亲水金、憎水二氧化硅纳米颗粒固定葡萄糖氧化酶（ＧＯＤ）,采有聚乙烯醇缩丁醛（ＰＶＢ）为辅助固酶膜基质来制备葡萄糖生物传感器,并考察了亲水金、憎水二氧化硅纳米颗粒对酶电极电流响应的影响。实验表明,引入纳米粒子可显著增强电极响应灵敏度,并对两种不同性质纳米所起作用的可能机理进行讨论,从理论和实验上辛 明了纳米颗粒对固定酶的作用。为制备有实用价值的葡萄糖生物传感器提供了可供参考的实验和理论依据。     

利用层层累积技术制备基于纳米碳管的葡萄糖生物传感器

以多壁纳米碳管(MWNTS)为电子媒介体和酶的吸附载体,利用层层累积的自组装技术固定葡萄糖氧化酶(GOX)的多层(MWNTa/GOx).复合薄膜修饰电极,制备了一种新型葡萄糖生物传感器.结果表明,传感器对葡萄糖的响应电流值随着MWNTa//GOx复合薄膜层数的不同而变化,当MWNTa//GOx复合薄膜的层教为6时,响应电流值迭到最大.(MWNTs/GOx).复合薄膜修饰的葡萄糖生物传感器对30mmol/L葡萄糖的响应电流为1.63μA,响应时间仅为6.7 s.该生物传感器检测的线性范围为0.5～15 mmol/L,最低检测浓度可达0.09 mmol/L.     

天青Ⅰ为电子媒介体金纳米颗粒修饰葡萄糖生物传感器

用纳米金溶胶与聚乙烯醇缩丁醛(PVB)构成复合固酶基质,采用溶胶凝胶法固定葡萄糖氧化酶(GOx)于铂金电极表面,并在葡萄糖溶液中加入天青Ⅰ作为电子媒介体,制成了新型葡萄糖生物传感器。实验证明,葡萄糖氧化酶吸附在纳米金颗粒表面上稳定且保持其生物活性;而电子媒介体的存在,显著提高了传感器的响应灵敏度。该传感器对葡萄糖响应的线性范围为2.5×10-5～7.5×10-3mol/L;检出限为8.5×10-6mol/L(S/N=3)。该生物传感器用于人体血清中的葡萄糖测定,结果令人满意。     

超细银－金复合颗粒增强酶生物传感器的研究

用琥珀酸二异辛酯磺酸钠／环已烷反胶束体系合成憎水纳米银－金复合颗粒， 并用此纳米银－金颗粒与聚乙烯醇缩丁醛构成复合固酶模基质，用溶胶－凝胶法固 定葡萄糖氧化酶，构建葡萄糖生物传感器。实验表明，纳米憎水银－金颗粒可以大 幅度提高固定化酶的催化活性，响应电流从相应浓度的几十纳安增强几万纳安。探 讨了纳米颗粒效应在固定化酶中所起的作用，为纳米颗粒在生物传感器领域中的应 用提供了可参考的实验和理论依据。     

以高氯酸·三-2,2′-联吡啶合钴(Ⅲ)作为电子媒介体金纳米颗粒增强的葡萄糖生物传感器

用纳米金溶胶与聚乙烯醇缩丁醛(PVB)构成复合固酶基质,采用溶胶-凝胶法固定葡萄糖氧化酶(GOx)于铂电极表面,并在葡萄糖溶液中加入高氯酸·三-2,2′-联吡啶合钴(Ⅲ)作为电子媒介体,制成了高灵敏的葡萄糖生物传感器.葡萄糖氧化酶吸附在纳米金颗粒表面上稳定且保持其生物活性;而电子媒介体的存在,显著提高了传感器的响应灵敏度.该传感器对葡萄糖响应的线性范围为1.2×10-8～6.2×10-6 mol/L,检出限6.2×10-9 mol/L(S/N=3).该生物传感器有效消除了抗坏血酸、尿酸的干扰,可用于人体血清中葡萄糖的测定.     

光照纳米银颗粒对葡萄糖生物传感器响应电流的抑制

采用纳米银-壳聚糖复合膜固定葡萄糖氧化酶,构建葡萄糖生物传感器.利用计时电流法对不同光照时间纳米银颗粒组装的酶电极响应电流进行了表征.实验结果表明,光照纳米银颗粒可以抑制葡萄糖生物传感器的响应电流;随着光照时间的延长,纳米银颗粒的抑制作用逐渐增强,当光照时间达到120min时,葡萄糖生物传感器的响应电流最小(-3.953μA/cm²).葡萄糖生物传感器响应电流的抑制可能是由纳米银颗粒表面的Ag⁺离子浓度及表面性能的变化引起的.     

纳米铂颗粒修饰薄膜金电极的新型葡萄糖传感器研究

在没有引入电子媒介体条件下,为了提高传感器的响应灵敏度,降低工作电位,利用电化学沉积法在薄膜金电极表面修饰纳米铂颗粒,并通过戊二醛固定酶的方法制备了一种新型生物传感器。研究了在薄膜金电极上修饰纳米铂颗粒前后传感器对低浓度葡萄糖的响应影响。结果表明,纳米铂颗粒修饰后所制备的葡萄糖传感器工作电位下降为0.4 V,测定葡萄糖的检出限从100μmol/L下降到10μmol/L。传感器对10~1300μmol/L低浓度葡萄糖的响应灵敏度为50.8 nA/(cm2μmol/L);响应时间30 s;r为0.9974;传感器精密度为2.1%,并具有较好的稳定性。     

纳米复合物修饰电极的电化学传感器检测芦丁

研制了纳米复合物修饰电极,碳纳米管与表面含有大量氨基的壳聚糖在玻碳电极表面首先形成碳纳米管/壳聚糖膜,通过膜表面丰富的氨基与纳米Au的强静电吸附,在玻碳电极表面获得均匀致密的纳米金修饰层.这种基于纳米复合材料制备的新型电化学传感器对芦丁具有很好的响应,可以快速地实现电极与芦丁之间的直接电子转移,有良好的稳定性.芦丁的测定线性范围为4.00×10-7～1.77×10-5 mol/L,最低检测限为1.29×10-7 mol/L.由于抗坏血酸在该修饰电极上的氧化电位出现显著负移,因此可避免抗坏血酸对芦丁测定的干扰.该方法可以不经预分离直接检测药物中的芦丁含量.     

An intimately bonded titanate nanotube–polyaniline–gold nanoparticle ternary composite as a scaffold for electrochemical enzyme biosensors

In this work, titanate nanotubes (TNTs), polyaniline (PANI) and gold nanoparticles (GNPs) were assembled to form a ternary composite, which was then applied on an electrode as a scaffold of an electrochemical enzyme biosensor. The scaffold was constructed by oxidatively polymerising aniline to produce an emeraldine salt of PANI on TNTs, followed by gold nanoparticle deposition. A novel aspect of this scaffold lies in the use of the emeraldine salt of PANI as a molecular wire between TNTs and GNPs. Using horseradish peroxidase (HRP) as a model enzyme, voltammetric results demonstrated that direct electron transfer of HRP was achieved at both TNT-PANI and TNT-PANI-GNP-modified electrodes. More significantly, the catalytic reduction current of H₂O₂ by HRP was ∼75% enhanced at the TNT-PANI-GNP-modified electrode, compared to that at the TNT-PANI-modified electrode. The heterogeneous electron transfer rate constant of HRP was found to be ∼3 times larger at the TNT-PANI-GNP-modified electrode than that at the TNT-PANI-modified electrode. Based on chronoamperometric detection of H₂O₂, a linear range from 1 to 1200 μM, a sensitivity of 22.7 μA mM⁻¹ and a detection limit of 0.13 μM were obtained at the TNT-PANI-GNP-modified electrode. The performance of the biosensor can be ascribed to the superior synergistic properties of the ternary composite.     

Functional graphene-gold nano-composite fabricated electrochemical biosensor for direct and rapid detection of bisphenol A

In this research, the graphene with excellent dispersity is prepared successfully by introducing gold nanoparticle to separate the individual sheets. Various techniques are adopted to characterize the prepared graphene and graphene-gold nanoparticle composite materials. This fabricated new composite material is used as the support material to construct a novel tyrosinase based biosensor for detection of bisphenol A (BPA). The electrochemical performances of the proposed new enzyme biosensor were investigated by differential pulse voltammetry (DPV) method. The proposed biosensor exhibited excellent performance for BPA determination with a wide linear range (2.5 × 10⁻³–3.0 μM), a highly reproducible response (RSD of 2.7%), low interferences and long-term stability. And more importantly, the calculated detection limit of the proposed biosensor was as low as 1 nM. Compared with other detection methods, this graphene-gold nanoparticle composite based tyrosinase biosensor is proved to be a promising and reliable tool for rapid detection of BPA for on-site analysis of emergency BPA related pollution affairs.     

A Novel Bioelectrochemical Sensor Based on Immobilized Urease on the Surface of Nickel Oxide Nanoparticle and Polypyrrole Composite Modified Pt Electrode

Nickel oxide nanoparticle (NiO?NP) and polypyrrole (PPy) composite were deposited on a Pt electrode for fabrication of a urea biosensor. To develop the sensor, a thin film of PPy?NiO composite was deposited on a Pt substrate that serves as a matrix for the immobilization of enzyme. Urease was immobilized on the surface of Pt/PPy?NiO by a physical adsorption. The response of the fabricated electrode (Pt/PPy?NiO/Urs) towards urea was analyzed by chronoamperometry and cyclic voltammetry (CV) techniques. Electrochemical response of the bio‐electrode was significantly enhanced. This is due to electron transfer between Ni²⁺ and Ni³⁺ as the electro‐catalytic group and the reaction between polypyrrole and the urease‐liberated ammonium. The fabricated electrode showed reliable and demonstrated perfectly linear response (0.7–26.7 mM of urea concentration, R²= 0.993), with high sensitivity (0.153 mA mM^?1 cm^?2), low detection of limit (1.6 μM), long stability (10 weeks), and low response time (～5 s). The developed biosensor was highly selective and obtained data were repeatable and reproduced using PPy‐NiO composite loaded with immobilized urease as urea biosensors.     

Structure and properties of porous composite membranes of regenerated silk fibroin and poly(vinyl alcohol) and biosensing of glucose via Meldola blue dispersed in polyester ionomer as an electron transfer mediator

Porous composite membranes of regenerated silk fibroin and poly(vinyl alcohol) were prepared by adding polyethyleneglycol to the composite solution to reduce the mass-transfer resistance to the diffusion of substrate material transport; their surfaces were visualized with scanning electron microscopy. An amperometric glucose biosensor employing Meldola blue dispersed in polyester ionomer as electron transfer mediator was prepared to test the feasibility and workability of the composite membrane as immobilization matrix for glucose oxidase. The cationic exchange property of the polyester ionomer was employed to provide high local concentrations of Meldola blue (MB⁺) in the polymer film via ion exchange. Performance and characteristics of the glucose biosensor were evaluated with respect to response time, detection limit, applied potential, thickness of polyester ionomer membrane, pH and temperature. The glucose biosensor possesses a variety of advantages including easy maintenance of enzyme, simplicity of construction, fast response time and high stability. Received: 13 May 1996 / Revised: 30 July 1996 / Accepted: 2 August 1996     

Evaluation of Immobilization Techniques for the Fabrication of Nanomaterial-Based Amperometric Glucose Biosensors

Eleven glucose biosensors were prepared by cross-linking, entrapment, and layer-by-layer assembly to investigate the influence of these immobilization methods on performance. The effects of separate nanozeolites combined with magnetic nanoparticles and multiwalled carbon nanotubes in the enzyme composition on the performance of glucose biosensors were compared. Cyclic voltammetric studies were carried out on the biosensors. Acrylonitrile copolymer/nanozeolite/carbon nanotube and acrylonitrile copolymer/nanozeolite/magnetic nanoparticle electrodes prepared by a cross-linking method showed the highest electroactivity. These results indicated that a synergistic effect occurred when multiwalled carbon nanotubes, magnetic nanoparticles, and nanozeolites were combined that greatly improved the electron transfer ability of the sensors. Amperometric measurements by the glucose oxidase electrodes were obtained that showed that the acrylonitrile copolymer/nanozeolite/carbon nanotube electrode was the most sensitive (10.959 microamperes per millimolar). The lowest detection limit for this biosensor was 0.02 millimolar glucose, with a linear dynamic range up to 3 millimolar. The response after thirty days was 81 percent of the initial current.     

A New Signal‐On Photoelectrochemical Biosensor Based on a Graphene/Quantum‐Dot Nanocomposite Amplified by the Dual‐Quenched Effect of Bipyridinium Relay and AuNPs

A new photoelectrochemical (PEC) biosensor was developed by using carboxyl‐functionalized graphene and CdSe nanoparticles. This sensitive interface was then successfully applied to detection of thrombin based on the dual‐quenched effect of PEC nanoparticle, which relied on the electron transfer of a bipyridinium relay and energy transfer of AuNPs. After recognition with an aptamer, the PEC nanoparticle was removed and a signal‐on PEC biosensor was obtained. Moreover, the bio‐barcode technique used in the preparation of PEC nanoparticle could avoid cross‐reaction and enhances the sensitivity. Taking advantages of the various methods mentioned above, the sensitivity could be easily enhanced. In addition, in this work we also investigated graphene that was modified with different functional groups and AuNPs of different particle sizes. Under optimal conditions, a detection limit of 5.9×10^?15 M was achieved. With its simplicity, selectivity, and sensitivity, this strategy shows great promise for the fabrication of highly efficient PEC biosensors.     

CuTAPc-Fe3O4纳米复合粒子及其漆酶固定化研究

漆酶的固定化研究对基于漆酶催化的光纤生物传感器具有十分重要的意义，制备了四氨基酞菁铜(CuTAPc)-Fe3O4纳米复合粒子，并用红外(IR)、场发射扫描电镜(FEG—SEM)、X射线衍射(XRD)、能谱、粒径仪等对其进行了表征．结果表明形成了以CuTAPc包覆在Fe3O4纳米粒子表面的纳米复合粒子，粒子呈现不规则球形，且分布均匀，粒子平均粒径在50nm左右，用此纳米复合粒子通过戊二醛交联法固定了漆酶，固定后的酶比游离酶具有更好的贮存稳定性及操作稳定性，这为研制高性能的光纤生物传感器打下了较好的基础。