Properties of immiscible and ethylene-butyl acrylate-glycidyl methacrylate terpolymer compatibilized poly (lactic acid) and polypropylene blends

Poly(lactic acid) (PLA) and polypropylene (PP) blends of various proportions were prepared by melt-compounding. The miscibility, phase morphology, thermal behavior, and mechanical and rheological properties of the blends were investigated. The blends were immiscible systems with two typical morphologies, spherical droplet and co-continuous, and could be obtained at various compositions. Complex viscosity, storage modulus and loss modulus depend on the PP content. Thermal degradation of all blends led to two weight losses, for PLA and PP. The incorporation of PP improved the thermal stability of the blend. The effect of compatibilizer (ethylene-butyl acrylate-glycidyl methacrylate terpolymer, EBA-GMA) on the morphology and mechanical properties of 70/30 w/w PLA/PP blends was investigated. The tensile strength of these blends reached a maximum for 2.5 wt% EBA-GMA, and impact strength increased with increasing EBA-GMA content, suggesting that EBA-GMA is an effective compatibilizer for PLA/PP blends.     

Thermal degradation and crystallisation studies of reactively compatibilised polymer blends

The thermal degradation and crystallisation behaviours of polyamide12/isotactic polypropylene (PA12/PP) blends were studied. Effects of blend ratio and compatibiliser concentration on the thermal degradation properties of the blends were analysed. The activation energy for degradation in compatibilised and uncompatibilised blends computed using Horowitz-Metzger equation was reported. The blend ratio as well as the presence of compatibiliser has significant effect on the thermal stability of the blends. Phase morphology was found to be one of the decisive factors that affected the thermal stability of both uncompatibilised and compatibilised blends. Melting and crystallisation behaviours of the blends in the presence and absence of compatibiliser were evaluated. It was observed that blending has no significant effect on the melting and crystallisation properties of PA12 and PP. Compatibilisation of 70/30 and 50/50 PA12/PP blends didn't affect the crystallisation and melting behaviours of PA12 and PP even though some discrepancies were observed.     

Compatibility effect on the thermal degradation behaviour of polypropylene blends with polyamide 6, ethylene propylene diene copolymer and polyurethane

The morphology and thermal behaviour of polypropylene/polyamide 6 (PP/PA6), polypropylene/copolymer ethylene propylene diene (PP/PEBAX) and polypropylene/rigid polyurethane (PP/PUR) blends compatibilised with polypropylene-graft-maleic anhydride (PP-g-MA) were studied using scanning electron microscopy and thermogravimetric analyses. The study focuses on the influence of different blends obtained by mixing a thermoplastic, thermoplastic elastomer or thermoset with PP, compatibilised with PP-g-MA. The compatibilising effect of PP-g-MA in an immiscible PP/PA6 blend induces a homogeneous dispersion due to interfacial adhesion. For the PP/PEBAX and PP/PUR binary blends studied slight changes in the morphology were observed with a continuous phase but the PEBAX or PUR domains remained in the PP matrix. The deconvolution of the TGA curve permitted an evaluation of the decomposition stage of the undiluted and blend systems. Thermal stability is slightly influenced by the position of the maximum decomposition rate temperature of the first derivative thermogravimetric curve (DTG). However, the DTG curve profile remains consistent. The activation energy of undiluted PP was in the range of 162–169 kJ mol⁻¹ determined by the Ozawa method. The stabilized activation energy value for all blends studied above a 0.4 weight-loss fraction is discussed.     

Analysis and evaluation of biobased polyester of PTT/PBAT blend: thermal,dynamic mechanical,interfacial bonding,and morphological properties

Novel blends were prepared from biobased poly(trimethylene terephthalate) (PTT) and poly(butylene adipate‐co‐terephthalate) (PBAT) using a twin screw extrusion process as a function of different weight ratios. Thermal stability, mechanical, and interfacial properties of PTT/PBAT blends were investigated using a thermogravimetric analyzer and mechanical analyzer. Phase behavior and surface morphology of the blends were characterized using scanning electron microscopy. Interfacial bonding value of the PTT/PBAT blend was evaluated from the Pukanszky empirical relationship. Viscoelastic properties of PTT/PBAT blends were investigated using the dynamic mechanical analyzer. PTT/PBAT blend exhibited higher thermal stability than the neat PTT matrix. The entire blend showed better interfacial adhesion between the matrixes. Storage and loss modulus of the PTT/PBAT blend reduces with increasing PBAT content. PTT/PBAT blend exhibited higher impact energy than the neat PTT matrix, because of its flexible and amorphous nature of PBAT polymer and increasing toughness. Copyright © 2016 John Wiley & Sons, Ltd.     

PREFERENTIAL INTERCALATION BEHAVIOR OF CLAY AND ITS EFFECT ON THE THERMAL DEGRADATION IN IMMISCIBLE PP/PS BLENDS

The typical immiscible PP/PS blend based clay nanocomposites were prepared via melt blending.The dispersion of clay was determined by X-ray diffraction (XRD) and transmission electron microscopy (TEM).Thermal stability and dynamic mechanical properties were measured by thermogravimetrical analysis (TGA) and dynamic mechanical analysis (DMA),respectively.Preferential intercalation behavior of clay in PP/PS blends was found.The dispersion of clay is significantly influenced by the polarity of PP and PS,mea...     

Tailoring of interface of polypropylene/polystyrene/carbon nanofibre composites by polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene

Mechanical and physical properties of polypropylene (PP)/polystyrene (PS) blend, PP/PS/polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) ternary blend and their composites with carbon nanofibers (CNF) were investigated. Composites of ternary blend exhibited superior properties compared to those of binary blends. Mechanical performance of nanocomposites was intimately related to their phase morphology. PP/PS/SEBS/0.1 wt% CNF hybrid composites exhibited excellent impact strength (Four-fold increase compared to PP/PS blend) and ductility (12-fold increase in elongation at break, with respect to PP/PS blend). Moreover, these composites displayed good tensile strength and modulus (15% increase in Young's modulus, compared to PP/PS/SEBS blend) and are suitable for various end-use applications including automobile applications. Although crystallinity of PP phase is decreased by the incorporation of CNF, thermal stability of the composites remained almost unaffected. Contact angle measurements revealed that ternary composites exhibited maximum hydrophobicity.     

Compatibilization of polypropylene/poly(glycolic acid) blend with maleated poe/attapulgite hybrid compatibilizer: Evaluation of mechanical,thermal, rheological,and morphological characteristics

In this work, the compatibilization effects of hybrid maleated POE/attapulgite hybrid compatibilizer (M-POE/ATP) on the immiscible polypropylene/poly(glycolic acid) (PP/PGA) blends was investigated. The hybrid compatibilizer integrating strengthening, toughening and compatibilization functions was prepared via one-step reactive extrusion using peroxidated ATP as the initiator. Then, the effects of compatibilizer dosage on the mechanical, thermal, rheological and morphological characteristics of blends were evaluated in detail. It was found that the hybrid compatibilizer resulted in the significantly enhanced compatibility and mechanical performance. Increased amount of compatibilizer content fractionated and almost wholly suppressed the crystallization process of PGA. The compatibilized blends showed higher thermal stability than pure PGA, and lower storage modulus and complex viscosity at higher shearing frequency. PGA in the blends presented a much lower degradation rate, which lead to the higher strength retention of 81% for the blend with 4 wt% of compatibilizer in buffer solution after 35 days.     

Multiwalled carbon nanotube promotes crystallisation while preserving co-continuous phase morphology of polycarbonate/polypropylene blend

The influence of multiwalled carbon nanotubes (MWCNTs) on phase morphology, lamellar structure, thermal stability, melting behaviour and isothermal crystallisation kinetics of polycarbonate/polypropylene (PC/PP) blend nanocomposites has been investigated. Both neat blends and PC/PP (60/40)/MWCNT nanocomposites were prepared by melt mixing method. Morphological analyses were performed by high-resolution X-ray micro-computed tomography and scanning electron microscopy. The co-continuous morphology of the blend was retained irrespective of MWCNT loading. In addition, a substantial refinement in the co-continuous structure was observed. Wide angle and small angle X-ray scattering studies were used to analyse the structural properties of the blend nanocomposites. The addition of MWCNT increases the long period of polypropylene. The influence of addition of MWCNT on the crystallisation temperature and equilibrium melting temperature (Tm°) of polypropylene was followed. The MWCNTs promote crystallisation rate of polypropylene in the blend nanocomposites.     

Thermogravimetric analysis of PVC/NR-b-PU blends

Thermal stability of solution-cast blends of poly(vinylchloride) and NR-b-PU block copolymers of three different chain extender diols was studied by thermogravimetry. Thermal degradation of individual components and their blends were investigated with special reference to blend ratio. As the block copolymer content in the blends increased their thermal stability was also found to increase. Enhanced thermal stability of PVC is believed due to the favorable interaction with PVC and the PU hard segments of the block copolymer. DTG curves were used for the determination of different stages involved in the degradation. Activation energy for degradation was determined from Coats–Redfern plot.     

Thermal conductivity of poly(vinyl chloride)/polycaprolactone blends

Thermal diffusivity, heat capacity, and density of polyvinyl chloride/polycaprolactone (PVC/PCL) blends were measured by the laser flash method, DSC, and pycnometry, respectively. The thermal conductivity of the PVC/PCL blends was determined from the results. The miscibility of the blend and crystallinity of PCL were determined by DSC. The effect of blend structure on thermal conductivity is discussed. The phase compositions of the PVC/PCL blends are of three types depending on PCL content: i.e., up to 33%, from 33 to 70%, and above 70% PCL by weight. Thermal conductivity, thermal diffusivity, and heat capacity of the PVC/PCL blends are strongly affected by the phase composition of the blend, which changes in a complicated way with PCL content. © 1994 John Wiley & Sons, Inc.     

Thermal and photo induced reactions in blends of polypropylene and poly(methyl methacrylate)

Thermal Volatilization Analysis (TVA) demonstrates that poly(methyl methacrylate) (PMMA) is stabilized by blending with polypropylene (PP). Although well-defined radical reactions occur in both polymers under 2537 Å radiation, there is no evidence of the formation of block or graft copolymers when blends of the two are irradiated. Preirradiation suppresses the amount of monomeric methyl methacrylate formed on subsequent thermal degradation. The missing methyl methacrylate units appear in the chain fragment fraction. The characteristics of the thermal degradation of blends of unirradiated PP with preirradiated PMMA are similar to those of unirradiated rather than pre-irradiated blends, thus emphasizing the importance of the PP component in determining the thermal stability of blends after irradiation. These observations are discussed mechanistically.     

Thermal and structural studies of polypropylene blended with esterified industrial waste lignin

Microwave-assisted chemical modification of lignin was achieved through esterification using maleic anhydride. Modified lignin (ML) was blended in different proportions up to 25 mass% with polypropylene (PP) using Brabender electronic Plasticorder at 190 °C. The structural and thermal properties of blends were investigated by thermogravometric analysis (TG), differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD) and scanning electron microscopy (SEM). TG analysis showed increased thermal stability of blends due to antioxidant property of ML, which opposed oxidative degradation of PP. DSC analysis indicted slight depression in a glass transition temperature and melting temperature of blends due to partial miscible blend behavior between PP and ML. All blends showed higher crystallization temperatures and continuously reducing percentage crystallinity with increasing ML proportion in the blends. WAXD analysis indicated that PP crystallized in β polymeric form in addition to α-form in the presence of ML. However, proportion of β-form did not show linear relation with increase in ML proportion, thus ML acts as β nucleating agent in the PP matrix. SEM analysis showed good dispersion/miscibility in PP matrix indicating modification in lignin is useful.     

TIME-DEPENDENT MORPHOLOGY OF POLYETHYLENE-POLYPROPYLENE BLENDS

The effect of time-temperature treatment on morphology of polyethylene-polypropylene (PE-PP) blends wasstudied to establish a relationship between thermal history, morphology and mechanical properties. Polypropylene (PP)homopolymers were used to blend with various polyethylenes (PE), including high density polyethylene (HDPE), lowdensity polyethylene (LDPE), linear low density polyethylene (LLDPE), and very and ultra low density polyethylene(VLDPE and ULDPE). The majority of the blends were prepared at a ratio of PE:PP = 80:20, while blends of PP and LLDPEwere prepared at various compositions. Thermal treatment was carried out at temperatures between the crystallizationtemperatures of PP and PEs to allow PP to crystallize first from the blends. On cooling further, PE crystallized too. A verydiffuse PP spherulite morphology in the PE matrix was formed in some partially miscible blends when PP was less than 20%by mass. Droplet-matrix structures were developed in other blends with either PP or PE as dispersed domains in a continuousmatrix, depending on the composition ratio. The scanning electron microscopy (SEM) images displayed a fibrillar structureof PP spherulite in the LLDPE-PP (80:20) and large droplets of PP in the HDPE-PP (80:20) blend, providing larger surfacearea and better bonding in the LLDPE-PP (80:20) blends. This explains why the blends with diffuse spherulite morphologyshowed greater improvement in tensile properties than droplet-matrix morphology blends after time-temperature treatment.     

Evaluation of the SEBS copolymer in the compatibility of PP/ABS blends through mechanical,thermal, thermomechanical properties,and morphology

Polypropylene (PP) blends with acrylonitrile-butadiene-styrene (ABS) were prepared using the styrene-ethylene-butylene-styrene copolymer (SEBS) as a compatibilizing agent. The blends were prepared in a co-rotational twin-screw extruder and injection molded. Torque rheometry, Izod impact strength, tensile strength, heat deflection temperature (HDT), differential scanning calorimetry, thermogravimetry, and scanning electron microscopy properties were investigated. The results showed that there was an increase in the torque of PA6/ABS blends with SEBS addition. The PP/ABS/SEBS (60/25/15%) blend showed significant improvement in impact strength, elongation at break, thermal stability, and HDT compared with neat PP. The elastic modulus and tensile strength have not been significantly reduced. The degree of crystallinity and the crystalline melting temperature increased, indicating a nucleating effect of ABS. The PP/ABS blends compatibilized with 12.5% and 15% SEBS presented morphology with well-distributed fine ABS particles with good interfacial adhesion. As a result, thermal stability has been improved over pure PP and the mechanical properties have been increased, especially impact strength. In general, the addition of the SEBS copolymer as the PP/ABS blend compatibilizer has the advantage of refining the blend's morphology, increasing its toughness and thermal stability, without jeopardizing other PP properties.     

动态固化聚丙烯/环氧树脂共混物的研究

将动态硫化技术应用于热塑性树脂 热固性树脂体系 ,制备了动态固化聚丙烯 (PP) 环氧树脂共混物 .研究了动态固化PP 环氧树脂共混物中两组分的相容性、力学性能、热性能和动态力学性能 .实验结果表明 ,马来酸酐接枝的聚丙烯 (PP g MAH)作为PP和环氧树脂体系的增容剂 ,使分散相环氧树脂颗粒变细 ,增加了两组分的界面作用力 ,改善了共混物的力学性能 .与PP相比 ,动态固化PP 环氧树脂共混物具有较高的强度和模量 ,含 5 %环氧树脂的共混物拉伸强度和弯曲模量分别提高了 30 %和 5 0 % ,冲击强度增加了 15 % ,但断裂伸长率却明显降低 .继续增加环氧树脂的含量 ,共混物的拉伸强度和弯曲模量增加缓慢 ,冲击强度无明显变化 ,断裂伸长率进一步降低 .动态力学性能分析 (DMTA)表明动态固化PP 环氧树脂共混物是两相结构 ,具有较高的储能模量 (E′)     

Large impact in electrical properties of polypropylene by improving the filler-matrix interface effect in PP/PS blends

Inorganic nanoparticles are widely used to improve space charge behavior, DC breakdown strength and other electrical properties of polymer insulating materials, but the uniform distribution of inorganic nanofillers in matrix is difficult due to their agglomeration and bad compatibility with the polymeric matrix. In this paper, polypropylene (PP)/polystyrene (PS) blends were prepared to suppress space charge accumulation and improve DC breakdown strength. Polypropylene-g-polystyrene (PP-g-PS) graft copolymer was used as compatibilizer to improve the compatibility of PP matrix and PS filler. The evolution of microstructure of PP/PS blends were investigated by scanning electron microscope (SEM), the space charge distributions were measured by a pulsed electro-acoustic (PEA) system, and DC breakdown strength was also tested. The morphologies show that the size of PS particles reduced to 310 nm when the content of PP-g-PS graft copolymer increased to 24 wt%, and the interaction between PP matrix and PS particles enhanced. The presence of PS particles in all PP/PS blends suppressed the space charge accumulation compared to neat PP, but the DC breakdown strength in uncompatibilized blend was lower than neat PP. The increasing of content of PP-g-PS improved the DC breakdown strength with the maximum value of 408.9 kV/mm was obtained. This may attribute to excellent interface structure formed between PP matrix and PS particles.     

EC/CA共混物的相容性和热稳定性

EC/CA共混物的相容性和热稳定性;乙基纤维素;醋酸纤维素;溶液共混;相容性     

Thermal degradation of poly(vinyl chloride)/poly(ethylene oxide) blends: Thermogravimetric analysis

Thermal stability of poly(vinyl chloride)/poly(ethylene oxide) (PVC/PEO) blends has been investigated by thermogravimetric analysis (TGA) in dynamic and isothermal heating regime. PVC/PEO blends were prepared by hot-melt extrusion (HME). According to TG analysis, PEO decomposes in one stage, while PVC and PVC/PEO blends in two degradation stages. In order to evaluate the effect of PEO content on the thermal stability of PVC/PEO blends, different criteria were used. It was found that thermal stability of PVC/PEO blends depends on the blend composition. The interactions of blends components with their degradation products were confirmed. By using multiple heating rate kinetics the activation energies of the PVC/PEO blends thermal degradation were calculated by isoconversional integral Flynn–Wall–Ozawa and differential Friedman method. According to dependence of activation energy on degree of conversion the complexity of degradation processes was determined.     

Thermal stability and ageing properties of sulphur and gamma radiation vulcanized natural rubber (NR) and carboxylated styrene butadiene rubber (XSBR) latices and their blends

The thermal stability of natural rubber (NR) and carboxylated styrene butadiene rubber (XSBR) latices and their blends was studied by thermogravimetric methods. Ageing characteristics of these latex blends were studied by applying hot air oven thermal ageing for seven days at 70 °C. The mechanical properties of the aged samples were studied. Thermal degradation and ageing properties of these individual latices and their blends were investigated with special reference to blend ratio and vulcanization techniques. As the XSBR content in the blends increased their thermal stability was also found to increase. Among sulphur and radiation-vulcanized samples, radiation cured possesses higher thermal stability due to the higher thermal stability of carbon-carbon crosslinks. DTG curves were used for the determination of different stages involved in the degradation. Activation energy for degradation was determined from Coats-Redfern plot. The properties of aged samples were found to decrease due to chain depletion. However, the moduli of XSBR and NR/XSBR blends were found to increase owing to the formation of crosslinks upon ageing.     

辐射增强PP／BR共混体系的力学性能

研究了在多官能团单体－三烯丙基异氰酸酯存在下，共混体系聚丙烯／１．４－聚丁二烯橡胶的辐射效应，用ＤＳＣ，动态粘弹谱对其进行表征。结果显示，三烯丙基异氰酸酯主要分布于聚丙烯／１．４－聚丁二烯橡胶共混物的界面自高能射线作用下，被引发参与界面反应，从而改善了共混体系的相容性，增强也界面粘接，提高了共混物的力学性能。