PP/LDPE共混体系的辐射效应

研究了在多官能团单体—三烯丙基异氰脲酸酯存在下ＰＰ／ＬＤＰＥ共混体系接受γ－辐射的效果。用溶解度参数和ＴＥＭ技术评估了共混体系的相容性与多官能团单体在共混体系中的分布，并用ＳＥＭ、ＤＳＣ、动态力学等方法对共混体系相容性进行了表征。结果表明，ＰＰ／ＬＤＰＥ是不相容的共混体系，三烯丙基异氰脲酸酯主要分布在共混体系的相界面区域，辐照强化了共混体系的相间结合，增加了界面厚度，改善了共混体系的相容性。     

聚ε-己内酯/β-磷酸三钙共混物的制备与性能

研究了β－磷酸三钙和表面接枝改性β－磷酸三钙与聚ε－己内酯共混物的制备,共混体系的界面相互作用、热性能和力学性能。获得了全生物降解的聚ε－己内酯／β－磷酸三钙共混物材料。     

离聚体共混体系在溶液中分子间缔合的粘度研究

研究了磺化聚苯乙烯离聚体／聚（苯乙烯－４－乙烯吡啶）共混体系，磺化聚苯醚离聚体／聚（苯乙烯－４－乙烯吡啶）共混体系的磺化聚苯醚离聚体／胺化聚苯醚共混体系在氯仿／甲醇混合溶剂中的粘度行为，结果表明，和它们分别对应的不含离子基的共混物相比，这三个共混体系都表现出较高的比较粘度，这是由于体系中的酸基及其盐和含氮碱基的引入，在共混组分间产生了强烈的离子相互作用，从而导致分子间的缔合，使比浓粘度提高，并讨论     

聚烯烃共混物分散相尺寸梯度分布形态形成速度影响因素的研究

研究了聚烯烃高分子共混物的初始相形态及相间界面张力的改变对退火热处理条件下共混物分散相尺寸分布梯度形态形成速度的影响．通过控制共混物共混过程中Ｂｒａｂｅｎｄｅｒ转子的转速来控制共混物所受的剪切力大小，可达到控制共混物初始相形态的目的．通过ＳＥＭ电镜观察相形态，并利用计算机图象分析仪得到分散粒子的粒径及其分布数据．研究结果表明，转子转速越大，即共混物所受的剪切力越大，分散相初始粒径越小，且分散也越均匀．初始粒径较小的样品退火后形成梯度的速度相对较快．选用体系聚丙烯（ＰＰ）／乙烯 醋酸乙烯酯共聚物（ＥＶＡｃ）、聚乙烯（ＰＥ）／ＥＶＡｃ及改变ＥＶＡｃ中的醋酸乙烯酯（ＶＡｃ）含量与ＰＥ共混对比研究了不同相界面张力对梯度化速度的影响．结果表明，上述各体系退火热处理后均可形成梯度相形态，且相间界面张力越大．高分子共混物中梯度相形态形成速度也越快     

聚苯醚离子聚体／聚（苯乙烯—co—4—乙烯吡啶）共混体系的溶液行为

聚（２，６－二甲基－１，４－苯醚）高聚体／聚（苯乙烯－ｃｏ－４－乙烯吡啶）共混物的溶液行为研究表明，与对应的ＰＰＯ／ＰＳＶＰ共混物相比，这两个系列的共混的都表现出较高的比浓粘度。     

硅橡胶热降解动力学的研究

用恒温热失重方法，研究了甲基硅橡胶（Ｓｉ—Ｏ—１），用氢氧化钾催化聚合的甲基硅橡胶（Ｓｉ—Ｏ—２），主链含环二硅氮烷的硅氮橡胶（Ｓｉ—Ｎ—１）以及它与Ｓｉ—Ｏ—１的共混物Ｓｉ—Ｏ—３和与Ｓｉ—Ｏ—２的共混物Ｓｉ—Ｏ—４的热降解反应动力学．结果表明Ｓｉ—Ｎ—１有最高的热稳定性，在氮气下，其降解反应活化能为３４４ｋＪ／ｍｏｌ．并且发现它分别与Ｓｉ—Ｏ—１和Ｓｉ—Ｏ—２的共混物的热稳定性大幅度提高．Ｓｉ—Ｏ—３在氮气下的降解活化能由未加入Ｓｉ—Ｎ—１前的１５２ｋＪ／ｍｏｌ提高到２３０ｋＪ／ｍｏｌ；Ｓｉ─Ｏ─４则由未混入Ｓｉ─Ｎ─１前的６１ｋＪ／ｍｏｌ提高到１４４ｋＪ／ｍｏｌ．我们认为这种作用机理是由于硅氮橡胶除去了微量吸附水和硅羟基并导致催化剂的离子对难于分离的结果．     

PBT／PC共混体系流变性能与形态结构研究

采用毛细管流交仪测定了ＰＢＴ／ＰＣ共混物的表观粘度、剪切应力，观察了不同共混物组成和不同温度下共混物的流变行为，并借助扫描电镜对共混物和微观形态结构进行分析。结果表明：ＰＢＴ／ＰＣ熔体共混物的流变行为接近假塑性流体．温度对共混物的流变行为影响很大，共混物的熔体粘度在ＰＢＴ／ＰＣ为９０／１０和６０／４０时呈双极值．共混物为两相结构，ＰＣ含量为４－５０％时呈两互锁结构。     

苯乙烯在顺1,4-聚丁二烯上的接枝共聚反应动力学的Monte Carlo模拟

用ＭｏｎｔｅＣａｒｌｏ模拟方法对苯乙烯在顺１，４－聚丁二烯上的接枝反应动力学进行了研究。模拟结果表明，对于不同的橡胶浓度，接枝的和均聚的聚苯乙烯的数均聚合度、接枝效率与苯乙烯在顺１，４－聚丁二烯上的接枝共聚反应的动力学的解析解十分吻合，证明本方法能够有效地应用于自由基型接枝共聚合反应体系。     

烯丙基钯催化区域选择性氧化制备甲基酮的研究

报道了以氯化钯作催化剂，区域选择性氧化９－烯丙基－１－氧代－４－氮杂双环（４．３．０）壬烷及１０－烯丙基－１－氧代－４－氮杂双环（５．３．０）癸烷，制备了９－丙酮基－１－氧化－４－氮杂双环（４．３．０）壬烷及１０－丙酮基－１－氧代－４－氮杂双环（５．３．０）癸烷。比较了不同催化条件和溶剂系统的反应收率，发现以ＰｄＣｌ２／对－苯醌为催化系统和以含水的ＤＭＦ溶剂系统氧化收率最高。     

苯乙烯在顺1,4—聚丁二烯上的接枝共聚反应动力学的Monte Ca …

用Ｍｏｎｔｅ Ｃａｒｌｏ模拟方法对苯乙烯在顺１，４－聚丁二烯上的接枝反应动力学进行了研究。模拟结果表明，对于不同的橡胶浓度，接枝和均聚的聚苯乙烯的数均聚合度、接枝效率与苯乙烯在顺１，４－聚丁二烯上的接枝共聚反应的动力学的解析解十分吻合，证明本方法能够有效地应用于自由基型接枝共聚合反应体系。     

COMPATIBILIZERS FOR LOW DENSITY POLYETHYLENE/POLYPROPYLENE BLENDS

The role of polyolefin elastomers as compatibilizers in Low Density Polyethylene/Polypropylene (LDPE/PP) blends, in the presence of di-cumyl peroxide (DCP) has been studied. Mixtures of 90/10 LDPE/PP ratio, were prepared in a Brabender plasticorder and tested for their mechanical properties and calorimetric response. Then the elastomers ethylene-propylene-diene copolymer (EPDM) and polybutadiene (BR) were added, alone or together with 0.2% DCP at concentrations up to 2%. The mixing torque and gel content of the above products were recorded as a function of the blend consistency. Also, the mechanical properties of specimens were measured as an additional evidence to explore the capabilities of these additives to promote compatibility of the blend components. It was found that EPDM and BR can be easily incorporated into polyolefin blends and appear suitable as potential compatibilizers for those materials, probably acting within the PP phase. Both elastomers result in an increase of strength and modulus, the BR having more enhanced effect. The latter gives low elongation, which allows its use in applications where high tensile properties are desired and flexural behavior is not critical.     

聚丙烯／顺丁橡胶动态硫化增韧的研究

研究了在聚丙烯(pp)与顺丁橡胶(BR)共混过程中加入橡胶硫化剂使共混体系中橡胶相动态硫化交联。研究结果表明,采用动态硫化法可提高共混物的冲击强度和拉伸强度。借助于SEM和DMA,证实了动态硫化使PP/BR共混体系具有相界面粘结良好的多相结构,改善了两相相容性。探讨了动态硫化增韧的机理。     

The mechanical properties of radiation-vulcanized NR/BR blending system

The effect of radiation dose on the mechanical properties of NR/BR blending system is reported in this paper. A comparison was made between sulphur vulcanization and radiation vulcanization for an optimal nature rubber (NR)/ butyl rubber (BR) blending ratio (60/40) at dose range from 10 to 150 kGy. The result shows that the mechanical properties, especially, tensile strength, elongation at break, and tear strength have been improved significantly by radiation–vulcanization. This finding was also proved by thermal aging experiment on a selected NR/BR blend at 70°C for up to 168 h.     

Morphology and properties of polypropylene/ethylene–octene copolymer/clay nanocomposites with double compatibilizers

The influence of nanoclay on the morphology and properties of the polypropylene (PP)/ethylene–octene block copolymer (EOC) blend with double compatibilizers of maleated PP (PP‐g‐MA) and maleated EOC (EOC‐g‐MA) was investigated and compared with the nanocomposites containing either PP‐g‐MA or EOC‐g‐MA as a compatibilizer. X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy were utilized for morphological characterization in conjunction with dynamic mechanical thermal analysis, mechanical testing, and rheological evaluation of these nanocomposites. The results suggested that in the nanocomposite including both compatibilizers of PP‐g‐MA and EOC‐g‐MA, clay was dispersed as a mixed structure of intercalation and exfoliation in both phases of the polymer blend. Comparing the mechanical properties of the studied nanocomposite with nanocomposites of PP/EOC/PP‐g‐MA/clay and PP/EOC/EOC‐g‐MA/clay also indicated that the nanocomposite containing mixed compatibilizers displayed higher tensile modulus, tensile strength, and complex viscosity because of the better dispersion of clay in both phases. The results also confirmed the increased structural stability and reduced dispersed phase size of PP/EOC/PP‐g‐MA/EOC‐g‐MA blend in the presence of clay that proposed the compatibilization role of clay in this nanocomposite. Copyright © 2014 John Wiley & Sons, Ltd.     

动态固化聚丙烯/环氧树脂共混物的研究

将动态硫化技术应用于热塑性树脂 热固性树脂体系 ,制备了动态固化聚丙烯 (PP) 环氧树脂共混物 .研究了动态固化PP 环氧树脂共混物中两组分的相容性、力学性能、热性能和动态力学性能 .实验结果表明 ,马来酸酐接枝的聚丙烯 (PP g MAH)作为PP和环氧树脂体系的增容剂 ,使分散相环氧树脂颗粒变细 ,增加了两组分的界面作用力 ,改善了共混物的力学性能 .与PP相比 ,动态固化PP 环氧树脂共混物具有较高的强度和模量 ,含 5 %环氧树脂的共混物拉伸强度和弯曲模量分别提高了 30 %和 5 0 % ,冲击强度增加了 15 % ,但断裂伸长率却明显降低 .继续增加环氧树脂的含量 ,共混物的拉伸强度和弯曲模量增加缓慢 ,冲击强度无明显变化 ,断裂伸长率进一步降低 .动态力学性能分析 (DMTA)表明动态固化PP 环氧树脂共混物是两相结构 ,具有较高的储能模量 (E′)     

聚氯乙烯—低分子量聚异丁烯共混物的阻尼性质

聚氯乙烯(PVC)用作阻尼材料时多作成与高聚物的共混物,也有采用IPN的方法改善PVC的阻尼性能,前巳报导PVC-丁腈羟低聚物共混物有较佳的阻尼性质。本工作考察了PVC-PIB(聚异丁烯)组成及添加剂对共混物力学性能和动态力学性质的影响。     

Study on the toughening mechanism of PP/EVA dynamically crosslinked blend

The toughening mechanism of polypropylene (PP)/ethylene-co-vinyl acetate (EVA) dynamically crosslinked blend was investigated. The results indicated that dynamical crosslinking technology not only improved the interfacial adhesion between PP and EVA, but also increased the mechanical properties of PP/EVA blend. The quantitative and qualitative analysis of scanning electron microscopy (SEM) micrographs demonstrated that dynamical crosslinking technology could refine EVA particles in PP/EVA blend and promote the size distribution of EVA particles. The critical matrix ligament thickness of dynamically crosslinked and uncrosslinked blend was about 0.55 μm and 0.6 μm, respectively, indicating that the brittle-ductile transition occurred. Dynamic mechanical analysis (DMA) results illustrated that the tan δ peak of PP component in the dynamically crosslinked blend moved toward lower temperature compared with that of pure PP and the PP component in uncrosslinked blend; and the tan δ value of the dynamically crosslinked blend was higher than that of the uncrosslinked blend, which interpreted the toughening mechanism of dynamical crosslinking technology from the dynamic mechanical property of the blend.     

Characterization of irradiation-induced crosslink of epoxidised natural rubber/ethylene vinyl acetate (ENR-50/EVA) blend

The effect of irradiation on tensile, dynamic mechanical properties, thermal properties and morphology of ENR-50, EVA and ENR-50/EVA blend was investigated. All the samples were irradiated using a 3.0 MeV electron beam (EB) machine with doses ranging from 20 to 100 kGy. Results indicate that the gel fraction of ENR-50, EVA and ENR-50/EVA blend increases with irradiation dose. Concerning tensile properties, it can be seen that EB radiation increases the tensile strength of all the samples, increases the elongation at break of ENR-50 and ENR-50/EVA blend, reduces the elongation at break of EVA, increases M200 (modulus at 200% strain) of ENR-50 and EVA, while decreases M200 of the ENR-50/EVA blend. For dynamic mechanical studies, it was found that EB radiation increases the T_g of all the samples due to the effect of irradiation-induced crosslinking. The compatibility of ENR-50/EVA blend also found to be improving upon irradiation. In the case of thermal properties, it was detected that T_m, T_c and the degree of crystallinity of ENR-50/EVA blend increase with an increase in irradiation dose. This was due to the perfection in the crystal growth occurring upon radiation. Morphology changes play a major role in the changes of the properties of ENR-50/EVA blend. Finally, it can be concluded that ENR-50/EVA blend can be vulcanized by EB radiation.     

超细聚酰胺6粒子增韧聚丙烯体系的研究

采用磨盘形力化学反应器室温下制备了聚丙烯 (PP) /聚酰胺 6 (PA6 )超细粉体 ,研究了其粒度、粒度分布及PA6超细粒子填充对PP力学性能的影响 .结果表明 ,磨盘形力化学反应器可有效实现PP/PA6的粉碎 ,所得粉体平均粒径达微米级 ,初级粒子尺寸甚至可达纳米级 ,粒度分布呈双峰分布状态 .在PA6和PP熔点之间的温度下加工可制得PA6超细粒于填充的PP/PA6共混体系 ,其力学性能明显好于PP/PA6简单共混体系 ,30 %PA6用量下 ,拉伸强度由 2 3 .2MPa提高至 2 9 3MPa ,Izod缺口冲击强度由 4.6 2kJ/m2 提高到6 .34kJ/m2 .形貌分析结果表明 ,由于基本保持了PA6超细粉体的原始尺寸 ,填充体系中PA6相区尺寸小、分布均匀 ,与使用增容剂得到的相区结构类似 .