亚硫酸氢钠和半胱胺衍生法测定大气甲醛中碳同位素的研究

利用单体化合物稳定同位素(CSIA)技术研究了甲醛合次硫酸氢钠(HMSNa)与半胱胺衍生化过程的同位素效应,探讨了半胱胺衍生化法测定大气甲醛碳同位素的可行性。为了评价实验的稳定性与精确度以及衍生化过程的同位素效应,本实验采用不同同位素组成的HMSNa在酸性条件下分解,分解后的甲醛在碱性条件下与不同摩尔比的半胱胺反应,研究了该衍生化过程的反应条件和同位素效应。研究结果表明,HMSNa在pH值为1~2,60℃条件下分解,分解后的甲醛在PH值为8~9的条件下与摩尔比1∶20到1∶30半胱胺反应,该衍生化条件较为理想且该过程不存在同位素分馏;实验重现性好,测定精度高;可以用于大气甲醛同位素组成分析。     

甲基硼酸衍生法测定丁四醇中的碳同位素

对赤藻糖醇和苏阿糖醇进行甲基硼酸衍生化,并对反应物和生成的环状硼酸酯衍生产物进行稳定碳同位素测定.采用元素分析/同位素比质谱(EA/IRMS)对固体赤藻糖醇、苏阿糖醇、甲基硼酸的碳同位素的测定和气相色谱/燃烧/同位素比质谱(GC/C/IRM)对硼酸酯衍生产物的同位素测定的结果表明,当衍生化反应温度为60 ℃,反应时间为60 min,甲基硼酸和四醇化合物的摩尔比为10: 1时,通过反应物的同位素值及质量平衡关系计算而得的硼酸酯的δ13C数值和实际测定的产物的碳同位素之间的差异小于0.5‰,在该衍生化反应过程中不存在同位素分馏.此外,在GC/MS上,对赤藻糖醇、苏阿糖醇、2-甲基赤藻糖醇、2-甲基苏阿糖醇的甲基硼酸酯衍生产物进行确认,为进一步对天然源气溶胶中的2-甲基丁四醇进行稳定碳同位素分析提供实验基础.     

气相色谱同位素比值质谱法在线测定天然气稳定碳同位素

1 引言 色谱同位素比值质谱（GC-IRMS）技术是一种在线分析天然气中轻质烃类组分的新技术。可以在分子水平上连续测定从GC流出的每个化合物的碳同位素组成。在天然气的研究中，碳同位素是一个敏感指标，可信度和测量准确度高。本实验利用GC／C／IRMS联用仪，采用在线分析技术，并在开放体系中瞬间取样，分析了新疆灰岩和四川泥岩样品热模拟气的单体烃碳同位素值，可望为GC-IRMS技术在气／源对比和油气地质勘探中的应用提供参考，如利用模拟气测试的碳同位素比值可被地质上用来进行气一源岩相关研究，判断天然气的来源及源岩的成熟度等。     

六六六异构体稳定碳同位素组成分析

采用GC-C-IRMS、EA-IRMS和Dual-inlet IRMS 3种稳定同位素比值质谱仪分别对六六六的α、β和γ3种异构体的稳定碳同位素组成进行了分析。对比3种分析系统测定的碳同位素组成数据表明GC-C-IRMS系统能够准确和精确地测定六六六碳同位素组成。应用GC-C-IRMS技术分析了水样品中α-和γ-六六六的碳同位素组成,结果表明六六六在溶解、稀释、萃取、挥发等过程碳同位素组成没有分馏现象。采用GC-C-IRMS技术分析环境样品中持久性有机氯农药稳定碳同位素组成可能得到广泛应用。     

肉类制品中微量锶的分离及^87Sr/^86Sr同位素比值测定

利用87Sr/86Sr同位素比值进行生物和古人类源区与迁徙的示踪是Sr同位素技术应用的新领域,也是考古研究和肉类食品溯源研究的新尝试。本研究对牛肉干粉采用酸溶、微波消解和灰化后硝酸提取等不同方法进行消解,比较了它们的离子交换分离效果和Sr同位素测定结果;用石英、石墨和瓷坩埚3种器皿对牛肉干粉进行灰化,检测了灰化器皿对87Sr/86Sr同位素比值的影响,从而确定了石英坩埚灰化的消解方法,建立了适合于肉类制品微量Sr的化学分离方法与87Sr/86Sr同位素比值测定方法。本方法包括肉类制品的石英坩埚灰化、离子交换分离和87Sr/86Sr比值的热离子化质谱测定。所建方法对肉类食品溯源和考古研究等领域富含有机质样品的Sr同位素比值测定具有普适性。     

卟啉化合物碳同位素的气相色谱同位素比值质谱测定技术

 对于卟啉碳同位素的测定 ,传统方法 (用HPLC分离出单个卟啉化合物 ,然后燃烧成CO2 进行碳同位素的测定 )需要的样品量大 (几mg)、耗时长 ,限制了其在化学、地球科学中的应用。该文作者建立的方法是通过对卟啉化合物进行衍生化反应 ,以增强卟啉的挥发性 ,使其适用于气相色谱 同位素比值质谱 (GC IRMS)技术。对衍生化反应的整个过程进行了同位素测定 ,证实最终的衍生化硅卟啉与初始的自由基卟啉化合物碳同位素的差值在分析误差范围之内 ,无明显的同位素分馏。     

元素分析仪-稳定同位素比值质谱仪测定胶乳总固形物碳含量及其稳定碳同位素

应用元素分析仪和稳定同位素比值质谱仪(EA-IRMS)联用技术测定了胶乳总固形物碳含量及其碳同位素比值δ~(13)C。将所采集的新鲜胶乳预先制成胶片,称取(0.500±0.100)mg样品,按EA仪器工作条件对其碳含量进行测定。分别用碳元素基准物质(尿素、天门冬氨酸、葡萄糖、蔗糖),在EA工作条件下测其碳元素,以碳质量为横坐标,CO_2峰面积为纵坐标制得标准曲线,结果表明其线性关系良好。对EA-IRMS系统作了稳定性和线性试验,前者达到小于0.1‰的要求,后者则满足同类仪器小于0.06‰·V~(-1)的要求。此外,还对Craig校正所得样品及3种CRMs的初始校正值作进一步校准的3种校准方法作了比较,结果表明:3种方法中回归法准确度最好,适用于不同性质、不同碳同位素组成的样品;而截距法只能用于碳同位素组成与参考气相近的样品的测量数据的校准;原始回归法则不能有效地消除测定过程中~(17)O的影响和样品燃烧过程中可能存在的同位素分馏的影响而不能用于结果校准。测得胶乳样品的总固形物碳质量分数为81.83%,δ~(13)C_(s-PDB)~M(PDB为国际标准拟箭石化石)为-26.70‰(回归法校准值)。     

固相微萃取-气相色谱/同位素质谱法测定水中挥发性有机物单体碳同位素

建立了采用75μm碳分子筛/聚二甲基硅氧烷(CAR-PDMS)纤维的固相微萃取-气相色谱/同位素质谱联用方法测定水中挥发性有机污染物碳同位素。使用浸入式固相微萃取和顶空固相微萃取方法进行实验确定在低浓度条件下最佳δ13C测试方法。通过使用顶空固相微萃取前处理技术进行单体同位素分析分析灵敏度更高,应用CSIA技术对1,2-二氯乙烯,三氯乙烯,四氯化碳进行单体同位素分析,方法的检出限为70μg/L,与样本的标准偏差小于0.3‰。该法适用于水体中微量挥发性有机污染物的同位素组成测定。     

气相色谱-稳定同位素质谱法测定溶解无机碳碳同位素

选用NaHCO3配制了浓度分别为0.24、1.19、2.38和4.76 mmol/L的溶解无机碳(D IC)溶液,经过1h、4h、8h和24h不同平衡时间,建立了一种分析D IC碳同位素的方法。不同浓度的D IC样品与其母质NaHCO3的1δ3C值之间的差值仅为(0.2~0.5)‰。通过对照组的实验结果和对空气CO2的碳同位素测试与研究,证明此方法可有效避免实验过程中大气等物质对样品的污染,确保实验结果的准确性。     

不同赋存形态土壤铅同位素比值用于判别地域性差异的研究

由于各地区地质结构不同,造成了铅同位素组成具有地域特征。本研究利用电感耦合等离子体质谱测定了福建不同茶园土壤的铅同位素比值,比较了土壤全消解和残渣态两种赋存形态的铅同位素比值的差异,发现残渣态的铅的地域性特征较强,可用来作为地区土壤的判别依据。     

O/O and H/D separation factors for liquid/vapor permeation of water through an hydrophobic membrane

Liquid/vapor permeation of water through commercial grade hydrophobic PTFE membranes at 323<P(Torr)<160, shows enhancements in logarithmic separation factors, ln[(i'/i)] = In [(χ'/χ) _downstream/ (χ'/χ) _upstream], which differ markedly for isotope separation of oxygen and hydrogen. The prime refers to the lighter isotope and χ is the mole fraction. Thus ln[(16/18)] is found to be as large as 6 times the ratio of the vapor pressure isotope effect, ln(_o = ln (P^o'/P^o), but ln[(H/D)]/ln[_o(H/D)] is only as large as 1.3. The difference in enhancement factors indicates that membrane transport mechanisms must be different for the two separations. The unusually large separation factor for ¹⁶O/¹⁸O may be of practical interest.     

Effect of H/D isotope substitution on polarizability of methanol molecules

The electron polarizabilities (α₀·10²⁴/cm³ molec.⁻¹) were estimated from the data on refractive indices and molar volumes of H/D isotopomers of methanol at 25 °C using the Lorentz-Lorentz formula: 3.265 (CH₃OH), 3.260 (CH₃OD), 3.235 (CD₃OH), and 3.231 (CD₃OD). A relationship between the isotope effects for α₀ and volume (packing) changes in the structure of liquid methanol induced by deuterosubstitution in the methanol molecule was proposed. __________ Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1927–1928, August, 2005.     

Continuous flow isotope ratio mass spectrometry for the measurement of nanomole amounts of (13)CO(2) by a reverse isotope dilution method

A simple method for the determination of nanomole amounts of (13)CO(2) generated from an in vitro reaction is reported. The incubation medium contains a known amount of unlabeled sodium bicarbonate and the gaseous (13)CO(2) enriches the atmosphere upon which a measurement of the isotopic enrichment ((13)CO(2)/(12)CO(2)) is made corresponding to a reverse isotope dilution. The quantification of the (13)CO(2) was performed by gas chromatography/isotope ratio mass spectrometry. This assay was validated in terms of linearity, accuracy and precision using three different substrates which produce (13)CO(2) either by enzymatic reaction [(13)C]urea, sodium [(13)C]formate) or by chemical reaction (sodium [(13)C]bicarbonate). Four calibration curves were tested for each (13)C-labeled substrate, allowing the quantification of (13)CO(2) from 25 pmol to 150 nmol. The dynamics of the assay were obtained as a function of the quantity of unlabeled sodium bicarbonate added to each sample.     

Isotope exchange kinetics at heterogeneous solid surfaces (solid-liquid interfaces)

A system of equations describing isotope exchange kinetics at heterogeneous solid surfaces (solid-liquid interfaces) is studied numerically. The theoretical kinetic curves, characterizing the isotope exchange, are calculated for different discrete distributions of the isotope exchange rate constant.

---

Isotopenaustauschkinetik an heterogenen Festkörperoberflächen (Fest-flüssig Grenzflächen)

Zusammenfassung Ein die Kinetik des Isotopenaustausches an heterogenen Festkörperflächen (fest-flüssig Grenzflächen) beschreibendes Gleichungssystem wird einer numerischen Auswertung unterzogen. Die theoretischen kinetischen Kurven des Isotopenaustausches werden für verschiedene diskontinuierliche Verteilungen der Isotopenaustausch-Geschwindigkeitskonstante berechnet.

     

Pitfalls in compound-specific isotope analysis of environmental samples

In the last decade compound-specific stable isotope analysis (CSIA) has evolved as a valuable technique in the field of environmental science, especially in contaminated site assessment. Instrumentation and methods exist for highly precise measurements of the isotopic composition of organic contaminants even in a very low concentration range. Nevertheless, the determination of precise and accurate isotope data of environmental samples can be a challenge. Since CSIA is gaining more and more popularity in the assessment of in situ biodegradation of organic contaminants, an increasing number of authorities and environmental consulting offices are interested in the application of the method for contaminated site remediation. Because of this, it is important to demonstrate the problems and limitations associated with compound-specific isotope measurements of environmental samples. In this review, potential pitfalls of the analytical procedure are critically discussed and strategies to avoid possible sources of error are provided. In order to maintain the analytical quality and to ensure the basis for reliable stable isotope data, recommendations on groundwater sampling, and sample preservation and storage are given. Important aspects of sample preparation and preconcentration techniques to improve sensitivity are highlighted. Problems related to chromatographic resolution and matrix interference are discussed that have to be considered in order to achieve accurate gas chromatography/isotope ratio mass spectrometry measurements. As a result, the need for a thorough investigation of compound-specific isotope fractionation effects introduced by any step of the overall analytical method by standards with known isotopic composition is emphasized. Finally, we address some important points that have to be considered when interpreting data from field investigations. Figure CSIA Principal (Carbon)     

Analysis of exponent values of Gaussian‐type functions on quantum protons and deuterons in charged or polarized systems

The optimal exponent α values (α_opt) in s‐type Gaussian‐type functions (GTFs) for quantum protons and deuterons, which are used for multicomponent molecular orbital calculations including nuclear quantum nature of protons and deuterons, are analyzed for several charged or polarized systems and their deuterated species. Ishimoto and coworkers (Ishimoto, Int. J. Quantum Chem. 2006 , 106, 1465) have already proposed the average exponent values for five neutral molecules (α_ave), and demonstrated that their α_ave enables us to evaluate the H/D isotope effect on energies and geometries of various neutral species. The differences between total energies of several charged or polarized systems with previous α_ave and our α_opt correspond to only less than 0.004% of the total energy (0.47 kcal·mol^?1) except for HeH⁺ and HeD⁺ molecules, while the difference between interaction energies of H₂OH^+…OH₂ and H₂OD^+…OH₂ systems with previous α_ave is 19% (0.22 kcal·mol^?1) smaller than that with our α_opt. Meanwhile, the difference between O? H bond lengths in H₂OH^+…OH₂ system with α_ave and α_opt values is 0.027 Å. We also found that the interaction energies with α_opt value at the geometry optimized with previous α_ave value (α_sp) well reproduce those at the geometry optimized with α_opt value. We have demonstrated that the nuclear basis functions based on s‐type GTFs with previous α_ave values enable us to evaluate the H/D isotope effect on energies and geometries of charged or polarized systems. © 2016 Wiley Periodicals, Inc.     

Quantification of intracellular homocysteine by stable isotope dilution liquid chromatography/tandem mass spectrometry

A precise and accurate stable isotope dilution liquid chromatography/tandem mass spectrometry method for the analysis of intracellular homocysteine has been developed. An internal standard, [(2)H(8)]-homocystine, was added to cell pellets from EA.hy 926 cells grown in culture under low and high folate concentrations. D,L-dithiothreitol was used to reduce cellular homocystine to homocysteine. Cellular proteins were precipitated by the addition of formic acid in acetonitrile. After centrifugation, a portion of the supernatant was analyzed by liquid chromatography/tandem mass spectrometry. Using a Supelcosil cyano column with an Applied Biosystems API 4000 triple quadrupole mass spectrometer, the SRM transitions for homocysteine (m/z 136 to m/z 90) and [(2)H(4)]-homocysteine (m/z 140 to m/z 94) were monitored. The method was validated by conducting five replicate analyses on three different days at four different concentrations (concentrations at the lower limit of quantitation and expected lower quartile, mid-range and upper quartile). The limit of detection was 2 ng/10(6) EA.hy 926 cells. Using this method, the intracellular homocysteine concentration in EA.hy 926 cells ranged from 10 to 36 ng/10(6) cells.     

Interpretation of butyltin mass spectra using isotope pattern reconstruction for the accurate measurement of isotope ratios from molecular clusters

The fragmentation patterns of butyltin compounds (mono-, di-, and tributyltin) in an electron impact ion source were studied using an isotope pattern reconstruction algorithm with emphasis on isotope ratio measurements from molecular clusters. For this purpose, standards of natural tin isotope abundance and a (119)Sn-enriched mixture of the three compounds were both ethylated and propylated using sodium tetraalkylborates. The corresponding mass spectra of the various tetraalkyltin compounds prepared were obtained by GC/MS after their extraction with hexane.The results showed that pure interference-free molecular clusters were obtained only for certain R(3)Sn(+) ions where no isobaric overlap with R(2)SnH(+) ions occurred (e.g. BuEt(2)Sn(+) overlaps with Bu(2)SnH(+)). These ions are ideal candidates for accurate Sn isotope ratio measurements, while isotope pattern perturbing interferences are observed for other molecular fragments down to Sn(.)(+). Isotope pattern reconstruction algorithm thus can be used as an analytical tool to ensure the absence of molecular interferences--a requirement for accurate isotope ratio measurements from molecular clusters. The relevance of these studies for the determination of butyltin compounds in environmental samples by isotope dilution GC/MS is also discussed.     

高压微波制备Pt／C催化剂的工艺研究

利用高压微波消解仪密闭带压、升温速率可控的特点,选择XC-72碳黑为载体,乙二醇为碳黑分散溶剂和还原剂,研究反应温度、升温速率、水含量、Pt含量及表面活性剂等工艺条件对Pt粒子尺寸及其分散度的影响．研究结果表明,快速升温到190℃、控制反应体系中水含量和Pt含量等工艺条件,可以得到Pt粒子平均粒径小于3．1nm的Pt／C催化剂,且Pt粒子分布均匀,无团聚．     

A generalized equation describing isotope exchange kinetics at solid-liquid interface

A generalization of the kinetic equation for the isotope exchange at solid—liquid interface is presented. The generalized equation may be used to describe kinetics of the isotope exchange process limited by surface reactions and diffusion without assumption of spherical symmetry of solid particles.

---

Eine generalisierte Gleichung für die Kinetik des Isotopenaustausches an Fest-Flüssig-Phasengrenzen

Zusammenfassung Es wird eine generalisierte kinetische Gleichung angegeben, die die Kinetik des Isotopenaustausches an Fest-Flüssig-Phasengrenzen beschreibt, wobei der Austauschprozeß durch Oberflächenreaktionen und Diffusion ohne der Annahme sphärischer Symmetrie für die festen Partikel begrenzt ist.