Cd基化合物纳米晶-有机聚合物杂化太阳能电池研究进展

有机-无机杂化太阳能电池因其结合了有机材料和无机材料各自的优势而引起了人们的广泛关注和研究. Cd基化合物纳米晶因其具有制备方法简单、尺寸及形貌可控、载流子迁移率高和稳定性好等优点而成为最早被研究的一类无机受体. 本文介绍了有机-无机杂化太阳能电池的结构及原理, 分析了影响有机-无机杂化太阳能电池效率的三个主要因素, 分别是开路电压(V_oc)、短路电流(J_sc)和填充因子(FF). 从改善Cd基化合物纳米晶的合成方法, 增加Cd基化合物纳米晶和有机聚合物间的界面接触, 以及优化Cd基化合物纳米晶和有机聚合物所用溶剂和所占比例等方面阐述了近年来Cd基化合物纳米晶-有机聚合物杂化太阳能电池的研究进展. 并展望了Cd基化合物纳米晶-有机聚合物杂化太阳能电池的发展方向.     

有机钌螯合物/TiO_2杂化膜修饰电极上Pt纳米团簇的光电流增强效应

利用LB膜技术可控制备了纳米单层和多层的二氧化钛-有机钌螯合物杂化膜,并研究了上述无机-有机杂化膜修饰电极在Pt纳米团簇敏化后的光电流增强效应.实验结果表明:(1)纳米单层TiO2/[Ru(phen)2(dC18bpy)]2+(简称为TiO2-Ru)杂化膜的平均厚度为(3.6±0.5)nm;(2)在光照条件下TiO2-Ru杂化膜能有效催化还原[Pt(NH3)6]4+形成粒径位于20～160nm之间的Pt纳米团簇;(3)Pt纳米团簇的引入消除了金属钌螯合物中配体对电子传递的阻碍作用,改变了电子传递途径,从而有效减少了电子空穴对的复合,提高了Pt纳米团簇敏化的n层杂化膜修饰电极(ITO/(TiO2-Ru)n/Pt)在支持电解质中的光电流.与纳米单层TiO2-Ru杂化膜修饰的ITO电极(ITO/TiO2-Ru)相比,当工作电压为900mV时,ITO/TiO2-Ru/Pt在0.1mol·L-1的NaClO4电解质溶液中和光照(λ360nm)条件下,单位面积的光电流提高了约5倍;(4)ITO/(TiO2-Ru)n/Pt电极光电流的大小与杂化膜的层数密切相关,当TiO2-Ru杂化膜的层数从一层、二层增加到四层时,光电流呈现先升高后下降行为,这表明ITO/(TiO2-Ru)n/Pt电极的电子传递过程直接通过非电活性的二氧化钛纳米单层进行.     

具有不对称孔道结构的小介孔二氧化硅粒子的合成及其高分子杂化膜的构建

利用手性阴离子酸表面活性剂, 采用软模板法制备了具有不对称孔道结构的小介孔二氧化硅(SiO₂)粒子. 将小介孔SiO₂粒子引入聚偏四氟乙烯(PVDF)和聚酰亚胺(PI)中构建了两种有机/无机杂化膜. 利用傅里叶变换红外光谱(FTIR)、 透射电子显微镜(TEM)、 扫描电子显微镜(SEM)和比表面积分析等表征了小介孔SiO₂粒子和有机/无机杂化膜的微结构, 并通过超滤实验和气体渗透实验分别考察两种杂化膜的性能. 研究结果表明, 表面含有大量亲水基团的小介孔SiO₂粒子具有规则有序排列的孔道结构, 该孔道结构呈现螺旋扭曲和不对称性. 构建的两种有机/无机杂化膜的极性显著提升, 进而有效增强了PVDF杂化膜的膜通量和抗污染性能及PI杂化膜对CO₂气体的分离性能, 克服了高分子膜的博弈效应(Trade-off效应). 另外, SiO₂的小介孔孔道还可以在PI杂化膜中引入优先通过CO₂分子的限域传质通道, 加速了CO₂气体在杂化膜中扩散. 但过多小介孔SiO₂粒子的加入导致其在高分子基质中团聚, 削弱杂化膜的极性和亲水性, 从而降低了两种杂化膜的分离性能.     

Pd纳米粒子敏化的纳米单层TiO_2-Ru(Ⅱ)螯合物修饰电极对单磷酸鸟苷的电催化氧化行为

利用LB膜技术可控制备了纳米单层的二氧化钛-有机钌螯合物杂化膜,并研究了上述无机-有机杂化膜修饰电极在Pd纳米粒子敏化后对单磷酸鸟苷(GMP)的电催化氧化行为.实验结果表明:(1)纳米单层TiO2/[Ru(phen)2(dC18bpy)]2+(简称为TiO2-Ru)杂化膜的平均厚度为(3.2±0.5)nm;(2)在光照条件下TiO2-Ru杂化膜能有效催化还原[Pd(NH3)4]2+形成粒径位于20～200nm之间的Pd纳米粒子;(3)纳米单层TiO2-Ru/Pd杂化膜能高效催化氧化具有供电子能力的单磷酸鸟苷(GMP),与纳米单层TiO2-Ru杂化膜修饰的ITO电极(ITO/TiO2-Ru)相比,当工作电压为1200mV时,ITO/TiO2-Ru/Pd电极在含有1×10-3molL-1GMP的磷酸盐缓冲液中,单位面积的催化氧化电流提高了约36倍;(4)Pd纳米粒子的引入消除了金属钌螯合物中配体对电子传递的阻碍作用,改变了电子传递途径,从而有效减少了电子空穴对的复合,提高了杂化膜修饰电极(ITO/TiO2-Ru/Pd)的电子传递效率.     

可聚合纳米无机氧化物杂化材料的制备及其在紫外光固化涂料中的应用

可聚合纳米无机氧化物杂化材料在紫外光固化涂料中具有较好的分散性能.与涂料中的单体和预聚物进行光聚合形成有机/无机杂化网络结构的聚合物,从而提高涂料固化膜的热稳定性能、硬度和耐磨性能等,在紫外光固化涂料的制备方面有着广阔的应用前景.目前,该类杂化材料主要采用硅烷偶联剂改性、化学接枝改性和溶胶一凝胶方法制备.本文就可聚合纳...     

ZrO2纳米粒子原位杂化PVDF膜的制备及其抗污染性能

针对传统聚合物膜抗污染性差的问题,本文从杂化膜结构设计出发,提出将ZrO2纳米粒子的原位制备和聚偏氟乙烯(PVDF)相转化成膜过程有机结合的制膜新方法.该方法将阴离子交换树脂引入到N,N-二甲基甲酰胺(DMF)中,以氧氯化锆为原料,利用阴离子交换树脂提供的―OH与无机盐的阴离子进行交换,得到ZrO2纳米粒子均匀分散的N,N-二甲基甲酰胺溶胶体系.随后将PVDF聚合物溶解到所得的N,N-二甲基甲酰胺溶胶体系中,获得均一、透明的铸膜液.利用X射线光电子能谱(XPS)和透射电子显微镜(TEM)对杂化膜中锆的存在状态和分散性能进行了表征.结果表明,ZrO2纳米粒子均匀分散在PVDF基体中,并且形成的纳米粒子的粒径约为10-20 nm.通过粘度、分相速度和膜形态的测定,研究了成膜机理.结果表明,ZrO2纳米粒子的引入加速了铸膜液成膜过程的分相速度.杂化膜的亲水性能通过接触角测定仪进行了评价.并选择以牛血清蛋白为代表模拟污染物,考察了杂化超滤膜的抗污染性能.结果表明,原位形成的ZrO2纳米粒子显著提高了膜的亲水性,减少了膜对蛋白质的吸附.这种将ZrO2纳米粒子的原位制备和PVDF相转化成膜过程有机结合的制膜新方法在有机-无机杂化膜的制备领域具有显著意义.     

有机-无机杂化膜的研究进展

有机-无机杂化膜由于具备了无机膜和有机膜各自的特点,具有良好的分离特性和物化稳定性,因而成为当前膜技术领域新型膜材料研究的热点.本文主要介绍了近年来国内外有机-无机杂化膜的研究现状、杂化膜的制备方法、结构和应用.     

基于改性亚麻仁油的有机/无机光固化膜的光固化机理及其反应性研究

用亚麻仁油和环戊二烯合成了改性亚麻仁油(NLO)光固化低聚物,其结构用红外光谱(FT-IR)进行了表征.基于改性亚麻仁油、巯基硅氧烷和光引发剂制备了有机/无机杂化光固化膜,对其光固化机理进行了分析,对无机粒子在改性亚麻仁油中的分布用AFM(原子力显微镜)进行了观测,建立了该有机/无机杂化体系的光固化模型.对杂化膜光固化反应性用Photo-差示扫描热分析仪(Photo-Differential Scanning Calorimeter)进行了测试,Photo-DSC测试结果表明:巯基硅氧烷能大大提高改性亚麻仁油体系光固化速率,环烯键对硫醇十分敏感.     

溶胶-凝胶法制备硅系有机-无机杂化分离膜

以α-Al₂O₃多孔陶瓷片为载体,用溶胶-凝胶法制备有机-无机杂化分离膜.通过考察前驱物的组成及杂化溶胶的合成条件对制膜工艺过程的影响,得到了制备有机-无机杂化分离膜的各种适宜性参数.红外光谱(FTIR)分析结果表明,杂化溶胶的性能不仅决定分离膜的性能,而且对膜热处理过程中的龟裂有很大影响.膜层的厚度为1～2μm;在膜两侧压差为0.10MPa、n(PTMOS)/n(TEOS)=1.16时,膜对O₂/N₂,CO₂/N₂和CO₂/O₂的分离因子分别为2.30,4.31和1.17,渗透系数为75.81×10^-17,75.28×10^-17和72.78×10^-17m₃(STP)·m/(m₂·s·Pa).     

有机-无机杂化分离膜研究进展

有机-无机杂化膜材料结合了有机膜材料和无机膜材料的优良性能,已成为分离膜材料研究的一个热点。本文以有机、无机组分间相互作用类型对其进行分类,着重介绍组分间以化学键相结合的有机-无机杂化膜的优良特性,总结了影响此类杂化膜结构和性能的主要因素,概括了它在膜分离中的应用,提出了目前研究工作中存在的不足,并做出了简要的述评。     

Flexible nanocrystalline‐titania/polyimide hybrids with high refractive index and excellent thermal dimensional stability

In this study, a novel synthetic route was developed to prepare polyimide–nanocrystalline–titania hybrid optical films with a relatively high titania content (up to 50 wt %) and thickness (20–30 μm) from soluble polyimides containing hydroxyl groups. Two series of newly soluble polyimides were synthesized from the hydroxy‐substituted diamines with various commercial tetracarboxylic dianhydrides. The hydroxyl groups on the backbone of the polyimides could provide the organic–inorganic bonding and resulted in homogeneous hybrid solutions by controlling the mole ratio of titanium butoxide/hydroxyl group. AFM, SEM, TEM, and XRD results indicated the formation of well‐dispersed nanocrystalline‐titania. The flexible hybrid films could be successfully obtained and revealed relatively good surface planarity, thermal dimensional stability, tunable refractive index, and high optical transparency. A three‐layer antireflection coating based on the hybrid films was prepared and showed a reflectance of less than 0.5% in the visible range indicated its potential optical applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1433–1440, 2010     

Preparation of photocurable silica–titania hybrid coatings by an anhydrous sol–gel process

Photocurable silica-titania hybrid coatings were prepared through an anhydrous sol–gel process. Moreover, test samples were prepared by the addition of definite ratios of fluoro acrylate oligomers into the formulations to manage the optical properties of transmitted light. Formulations were applied to corona-treated polycarbonate substrates. Upon adding the inorganic component to the coating material, thermal, mechanical, and other properties, such as hardness, gloss, contact angle, and flame resistance were improved. The photocured hybrid films showed an increase in the refractive index with increasing the titanium tetraisopropoxide content. As expected, a decrease was observed in the refractive index of the coatings with the incorporation of fluoro acrylate resin. The surface morphology of the hybrid films was characterized by ESEM analysis. In addition the chemical composition of the surface of the coatings was identified by ESEM–EDS technique. ESEM studies indicated that inorganic particles were dispersed homogenously throughout the organic matrix.     

High‐refractive‐index thin films prepared from aminoalkoxysilane‐capped pyromellitic dianhydride–titania hybrid materials

High‐refractive‐index aminoalkoxysilane‐capped pyromellitic dianhydride (PMDA)–titania hybrid optical thin films (TP0–TP8) were synthesized and characterized in this study. They were prepared with PMDA, aminopropyltrimethoxysilane, and titanium(IV) isopropoxide via a sol–gel process followed by spin coating and multistep baking. Through adjustments in the concentration and reaction time, the inorganic content in the hybrid thin films could be as high as 59.1 wt %. The Fourier transform infrared results indicated successful bonding between the organic and inorganic moieties. However, residues of the chelating ligands were found in the hybrids with high titania contents, affecting their thermal and optical properties. Field emission scanning electron microscopy results suggested a nanosized domain of the titania segment in the hybrid materials TP0–TP8. An atomic force microscopy study suggested that the hybrid thin films had good planarization. The dispersions of the refractive index and extinction coefficient in the wavelength range 190–900 nm were studied. The refractive indices of the prepared hybrid thin films at 633 nm increased linearly from 1.567 to 1.780 with increasing titania content. However, the Abbe numbers of the hybrid thin films showed an opposite trend. Excellent optical transparence was obtained in the visible region for the prepared hybrid thin films. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3419–3427, 2001     

High Refractive Index Films Prepared from Titanium Chloride and Methyl Methacrylate via a Non-Aqueous Sol–Gel Route

Poly(methylmethacrylate)/silica/titania films were prepared via a nonaqueous sol–gel route at ambient temperature, followed by spin-coating and multistep baking. The acrylic monomers used were methyl methacrylate (MMA) and 3-(trimethoxysilyl)propyl methacrylate (MSMA). Silicic acid and titanium(IV) chloride were used as the precursors of the inorganic component. FTIR results indicated the successful bonding between TiO₂ and SiO₂. TEM images suggested the silica/titania particles were well dispersed in the Poly(methyl methacrylate) (PMMA) matrix with the particles size smaller than 40 nm in our study. The refractive index and extinction coefficient were also studied. The refractive index of the hybrid increased with increasing the titania content, and the hybrid films showed high optical transparency in visible region.     

Synthesis and characterization of UV‐curable phosphorus containing hybrid materials prepared by sol–gel technique

In this study, a series of ultraviolet (UV)‐curable organic–inorganic hybrid coating materials containing phosphorus were prepared by sol–gel approach from acrylate end‐capped urethane resin, acrylated phenyl phosphine oxide oligomer (APPO), and inorganic precursors. TEOS and MAPTMS were used to obtain the silica network and Ti:acac complex was employed for the formation of the titania network in the hybrid coating systems. Coating performance of the hybrid coating materials applied on aluminum substrates was determined by the analysis techniques, such as hardness, gloss, impact strength, cross‐cut adhesion, taber abrasion resistance, which were accepted by international organization. Also, stress–strain test of the hybrids was carried out on the free films. These measurements showed that all the properties of the hybrids were enhanced effectively by gradual increase in sol–gel precursors and APPO oligomer content. The thermal behavior of the hybrid coatings was investigated by thermogravimetric analysis (TGA) analysis. The flame retardancy of the hybrid materials was examined by the limiting oxygen index (LOI); the LOI values of pure organic coating (BF) increased from 31 to 44 for the hybrid materials containing phosphorus (BF‐P:40/Si:10). The data from thermal analysis and LOI showed that the hybrid coating materials containing phosphorus have higher thermal stability and flame resistance properties than the organic polymer. Besides that, it was found that the double bond conversion values for the hybrid mixtures were adequate in order to form an organic matrix. The polycondensation reactions of TEOS and MAPTMS compounds were also investigated by ²⁹Si‐NMR spectroscopy. SEM studies of the hybrid coatings showed that silica/titania particles were homogenously dispersed through the organic matrix. In addition, it was determined that the hybrid material containing phosphorus and silica showed fibrillar structure. Copyright © 2009 John Wiley & Sons, Ltd.     

Trialkoxysilane‐capped acrylic resin/titania organic–inorganic hybrid optical films prepared by the sol–gel process

Homogeneous organic–inorganic hybrid materials with excellent thermal and optical performance were successfully prepared via the mixing of (3‐methacryloxypropyl)trimethoxysilane‐capped acrylic resin with titania synthesized by sol–gel approaches. The effects of the titania content, amount of water, and pH in the sol–gel and the ratio of the solvents (butyl acetate and ethanol) on the structures and properties of the hybrid materials were studied. More titania, more water, and base catalysis in the sol–gel process and a higher ratio of butyl acetate to ethanol for the hybrids led to a larger size and a more compact structure of the titania phase. Increasing the titania content dramatically improved the glass‐transition temperature, UV‐shielding properties, and refractive index for the hybrid materials, and it did not reduce their optical transparency. In general, better thermal stability and optical properties were achieved for the hybrid materials prepared with less water, lower pH values (e.g., acidic or neutral conditions), and a lower ratio of butyl acetate to ethanol. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 637–649, 2005     

溶胶-凝胶法制备二氧化钛纳米粒子及在光固化体系中的稳定分散

选用3种不同的稳定剂,乙酰丙酮(acac),异丙氧基三(焦磷酸二辛酯)钛(TTPO)和可聚合有机磷酸酯(MAP),采用钛酸四正丁酯(TBT)通过溶胶-凝胶法合成了一系列二氧化钛溶胶,并与树脂/单体相混合,制备成有机-无机杂化光固化涂料.利用FT-IR监测了TBT水解缩合形成溶胶的过程及杂化体系的光聚合过程.杂化固化膜SEM结果显示,在合成溶胶过程中添加不同的稳定剂对杂化固化膜中无机粒子粒径尺寸等形态有显著影响,其中使用TTPO作为稳定剂得到的无机粒子分散最均匀,粒径最小,约20 nm.物理性能测试表明光固化杂化膜在硬度和柔韧性方面都有明显的改善.     

A Study on Liquid Hybrid Material for Waveguides—Synthesis and Property of PSQ‐Ls for Waveguides

Silicate‐based inorganic‐organic hybrid polymer systems have many unique properties including thermal stability and photo‐stability, chemical resistance with the combination of tunable optical properties. Two kinds of new UV‐patternable hybrid materials PSQ‐Ls were synthesized by a sol‐gel process at room temperature, which can be used for low cost fabrication of optical waveguides. Thick films (up to 8.31 µm) can be coated by a single spin‐coating process without any cracking and the average surface roughness (Ra), detected by atomic force microscopy (AFM), is below 0.5 nm. The optical properties (refractive index, birefringence, and optical loss at 1310 nm and 1550 nm, respectively) of the PSQ‐Ls films are investigated by a prism coupler. The refractive index of PSQ‐Ls can be exactly tuned from 1.4483 to 1.5212 by blending PSQ‐LH (n_TE=1.5212 @ 1310 nm) and PSQ‐LL (n_TE=1.4483 @ 1310 nm). The maximum refractive index contrast is about 4.8%. After post‐baking, birefringences of the films are below 0.0005 and optical losses are about 0.2 dB · cm^?1 at 1310 nm, 0.7 dB · cm^?1 at 1550 nm, respectively. Furthermore, the PSQ‐Ls films also show outstanding thermal stability in air atmospheres.     

Preparation and evaluation of high-transparent scratch-resistant thin films on plasma treated polycarbonate substrate

New simple aqueous sol–gel procedure has been used for producing hard transparent organic–inorganic coatings on polycarbonate (PC). Sol-gel thins films were prepared by mixing Si and Al aqueous alkoxides and applied on the plasma treated PC. Tetraethyl orthosilicate (TEOS), 3-glycidoxypropyltrimethoxysilane (GPTMS) and aluminum tri sec-butoxide were used as main precursors. Before applying coatings PC were treated by Dielectric Barrier Discharge (DBD) system being conducted at atmosphere pressure. The effects of temperature, sols volume ratios and aging time on the coatings properties were scrutinized. Chemical, structural, morphological, optical and mechanical analyses of the samples were done by ATR-FTIR, EDS, XRD, FE-SEM, TEM, UV/vis spectroscopy, ellipsometry, pencil hardness and eraser scratch methods. TEM results showed well-dispersed nano-particles in the liquid sol. All of the films showed higher average transmittance (89 %) than the raw PC (86 %) that was stemmed from the lower refractive index (1.481) than raw PC (1.58). Films indicated good adhesion onto the plasma treated substrates (5B). The pencil hardness of the PC substrate (4B) improved to 3H (8 pencil grade increment) with just a single layer coating (775 nm thickness) due to the preparation of new hard structures of interlocked Si and Al atoms.     

Synthesis, characterization and flame retardant of UV-curable hybrid coatings containing SiO2–P2O5–B2O3 via sol–gel method

A ternary sol containing silicon, phosphorus and boron modified by ??-methacryloxypropyltrimethoxysilane was synthesized by sol?Cgel method. The ternary sol was incorporated into the organic matrix and UV-curable organic/inorganic hybrid coating materials were obtained. Hardness, transmittance, haze, cross-cut adhesion and abrasion resistance results showed that the mechanical properties of the hybrid coatings improved effectively with no comprising on optical properties by increasing sol content. Scanning electron microscopy and Energy Dispersive X-ray spectrometer studies indicated that inorganic particles were homogenously dispersed in the organic matrix. The flame retardancy of the UV-curable coatings was investigated by thermogravimetric analysis and microscale combustion calorimeter. The results showed that the incorporation of sol into the organic network led to an improvement in the thermal stability and flame retardancy of the hybrid coating materials. It is a desirable achievement to improve simultaneously both flame retardancy and mechanical properties of the coatings.