Mechanical, thermal, and fire properties of polylactide/starch blend/clay composites

Polylactide (PLA)/starch blend/clay and PLA/clay composites are prepared by melt blending. Structural and thermal characterizations are performed by differential scanning calorimetry, X-ray diffraction analysis, and thermogravimetric analysis. The fire properties are assessed on a dual cone calorimeter. Combustion residue and char formation is characterized by optical microscopy and attenuated total reflection infrared spectroscopy. Although the clay is not fully intercalated/exfoliated, the composites exhibit a higher thermal stability and much reduced peak heat release rate, and the PLA/starch blend composite retains its mechanical properties. For the PLA/starch blend composite, smoke release is also considerably reduced. Catalyzed, oxidative decomposition is shown to occur early in the thermal decomposition of the composites, prior to increased thermal stability. The inclusion of clay promotes char formation and increases the quantity of carbonaceous char in the combustion residue. There is minimal migration of the clay to the surface prior to ignition and char is formed mainly after ignition and during burning. During the later stages of burning some of the char formed is converted to CO₂.     

Mechanical and thermal properties of Acacia leucophloea fiber/epoxy composites: Influence of fiber loading and alkali treatment

In this work, the influence of fiber content and alkali treatment on the mechanical and thermal properties of Acacia leucophloea fiber-reinforced epoxy composites was studied. Ten composite samples were fabricated by varying fiber content (5, 10, 15, 20, and 25 wt%); both untreated and treated fiber were soaked in a 5% NaOH solution for 45 min by using hand-layup method. The composite reinforced with 20 wt% treated fiber content exhibited better mechanical properties and thermal properties. Fourier transform infrared analysis, morphological analysis by atomic force microscope, and scanning electron microscope of composites were also performed.     

Investigating the mechanical,thermal and melt flow index properties of HNTs – LLDPE nano composites for the applications of rotational moulding

Linear low density polyethylene (LLDPE) is the one of the most popular polymer used for rotational moulding applications such as storage tanks. But, its inferior mechanical properties and thermal stability restrict the longer service. Hence, this study experimentally demonstrates the effect of Halloysite Nanotube (HNTs) concentration on LLDPE composites for enhancing the mechanical and thermal stability. HNTs were uniformly dispersed with LLDPE matrix through ultra-sonication, followed by compression moulding used to prepare the nano composites plates. The prepared composites are shown 19.2% improved tensile strength for 2 wt% HNTs, whereas 28.9% hike in flexural strength observed for 4 wt% HNTs composite, compare to neat LLDPE. Which shows that higher concentrations of HNTs is favourable in improving the flexural strength rather than tensile properties. In addition to that, higher concentrations of HNTs are also helping in improving the storage modulus of the LLDPE composites. The increase in mechanical properties mainly attributed due to effective load carriers (HNTs) in the composite. Besides, HNTs were also contributing for improving the melting point and residual char of the composites, which is indeed for storage tanks durability. The prepared composite was thermally stable at higher temperature up to 230 °C, because of HNTs chemical structure, the inner layer of HNTs constitute with Al₂O₃ and outermost layer constitute with SiO_2, both are thermally stable. Stated enhancement proves the potential effect of HNTs reinforcement in the LLDPE composite for rotational moulding applications.     

Fabrication and characterization of gamma-irradiated recycled (thermoplastic/elastomer) matrix filled with feldspar composites

A composite of waste polyethylene, recycled waste rubber powder and reactive compatibilizing agent maleic anhydride, 60/40/2 mass%, was loaded with increasing contents, up to 20 mass%, of the reinforcing filler, feldspar [K (Al SiO₃O₈)]. The composites were gamma-irradiated at various doses up to 150 kGy. Selected physical, mechanical, and thermal parameters were investigated as functions of radiation dose and filler content. Gamma irradiation led to a significant improvement in the properties for all composites irradiated with 150 kGy. Similarly, the increase in feldspar content provided substantial improvement in properties as a result of development in the interfacial adhesion between the filler particles and composite components. The results were confirmed by examining the fracture surfaces using scanning electron microscopic techniques.     

Effect of nanosilica on thermal oxidative degradation of SBR

The effect of silica content on thermal oxidative stability of styrene–butadiene rubber (SBR)/silica composites has been studied. Morphologies of silica in SBR with different contents are investigated by scanning electron microscopy, which indicates that silica can well disperse in SBR matrix below the content of 40 %, otherwise aggregates or agglomerates will generate. Composites with around 40 % silica content show excellent mechanical properties and retention ratios after aging at 85 °C for 6 days. The values of activation energy (E _a) of pure SBR and its composites are calculated by Kissinger and Flynn–Wall–Ozawa methods based on thermogravimetric (TG) results, which suggests that composite with about 20 % silica has minimum E _a, and composite with 30–40 % silica has maximum E _a. According to TG curves, it is found that silica can suppress the formation of char leading to decline in stability to some extent. On the other side, silica also has positive effect on improving thermal stability of the matrix as filler. Thus, the SBR/silica composites with silica content of 30–40 % can possess both excellent resistance to thermal oxidative degradation and superior mechanical properties.     

Thermal resistance and mechanical stability of tungsten oxide filled polymer composite radiation shields

Abstract

The influence of tungsten oxide on thermal and mechanical properties of Isophthalic polyester was studied in detail. Ultrasonication technique was successful in dispersing WO₃ filler particles upto 40?wt% into the polymer matrix and was confirmed through the Scanning Electron Microscopy technique. The mechanical strength of the composites was found to increase with increase in the WO3 content and is acting as a reinforcer. About 77.4%, 65.4% and 7–8 times increase was observed in tensile, flexural and compressive strength respectively with respect to pristine. The thermogram of the composites reveal two stages of degradation. Maximum weight loss was observed in the first stage of degradation in almost all the composites. The initial degradation temperature of the composites range from 151?°C–226?°C. Activation energy was estimated using Horowitz–Metzger kinetic theory and was found to range from 25.31 to 78.58?kJ/Mol. The 50?wt% WO3 filled composite exhibits excellent thermal stability and mechanical strength. Thus, WO₃ filler particles were successful in enhancing the thermal and mechanical strength of Isophthalic polyester.     

Evaluation of activation energy conformity derived from model-free non-isothermal predictions and Arrhenius isothermal results

Organically modified montmorillonite (OMMT) was used as synergist to enhance the flame-retardant and mechanical properties of poly(butylene succinate)/intumescent flame retardant (PBS/IFR) composites. The flame-retardant, thermal degradation and combustion properties of PBS and its flame-retardant composites were characterized by limiting oxygen index (LOI) test, vertical burning (UL-94) test, thermogravimetric analysis, cone calorimeter and scanning electron microscopy, respectively. The results indicate that PBS/IFR composites exhibit excellent flame retardance when OMMT is at an appropriate content. PBS/IFR composite with 20 wt% IFR and 1.5 wt% OMMT has an LOI of 40.1% and can pass the UL-94 V0 rating. The synergistic effect between OMMT and IFR on the flame-retardant properties of PBS depends on the content of OMMT, and excessive OMMT diminish this synergistic effect. The possible flame-retardant mechanism of OMMT on PBS/IFR composite is proposed. The results of mechanical test also indicate that OMMT can effectively increase the notched impact strength of PBS/IFR composites.     

Influence of graphene reinforcement in conductive polymer: Synthesis and characterization

Lightweight conductive polymers are considered for lightning strike mitigation in composites by synthesizing intrinsically conductive polymers (ICPs) and by the inclusion of conductive fillers in insulating matrices. Conductive films based on polyaniline (PANI) and graphene have been developed to improve through‐thickness conductivity of polymer composites. The result shows that the conductivity of PANI enhanced by blending polyvinylpyrrolidone (PVP) and PANI in 3:1 ratio. Conductive composite thin films are prepared by dispersing graphene in PANI. The conductivity of composite films was found to increase by 40× at 20 wt% of graphene inclusion compared with PVP and PANI blend. Fourier‐transform‐infrared (FTIR) spectra confirmed in situ polymerization of the polymer blend. The inclusion of graphene also exhibits an increase in Tg by 21°C. Graphene additions also showed an increase in thermal stability by approximately 148°C in the composite films. The mechanical result obtained from DMA shows that inclusion of graphene increases the tensile strength by 48% at 20 wt% of graphene reinforcement. A thin, highly conductive surface that is compatible with a composite resin system can enhance the surface conductivity of composites, improving its lightning strike mitigation capabilities.     

Nanoclay modified silica phenolic composites: mechanical properties and thermal response under simulated atmospheric re‐entry conditions

Ablative nanocomposites based on nanoclay‐dispersed addition curable propargylated phenolic novolac (ACPR) resin, reinforced with chopped silica fiber, were investigated for their thermal response behavior under simulated heat flux conditions corresponding to typical atmospheric re‐entry conditions. Organically modified nanoclay (Cloisite 30B) was incorporated to different extents (1–10%) in the ACPR resin matrix containing silica fiber to form the composite. The composites displayed optimum mechanical properties at around 3 wt% of nanoclay loading. The resultant composites were evaluated for their ablative characteristics as well as mechanical, thermal and thermo‐physical properties. The reinforcing effect of nanoclay was established and correlated to the composition. The mechanical properties of the composites and its pyrolysed product improved at moderate nanoclay incorporation. Plasma arc jet studies revealed that front wall temperature is lowered by 20°C and that at backwall by 10–13°C for the 3 wt% nanoclay‐incorporated composites due to impedance by nanoclay for the heat conduction. Nanoclay diminished the coefficient of thermal expansion by almost 50% and also reduced the flammability of the composites. The trend in mechanical properties was correlated to the microstructural morphology of the composites. The nanomodification conferred better strength to the pyrolysed composites. Copyright © 2014 John Wiley & Sons, Ltd.     

Fabrication of Single Wall Carbon Nanotubes-Based Poly(vinyl butyral) Nanocomposites with Enhanced Mechanical and Thermal Properties

In this research, poly(vinyl butyral) (PVB)/single wall carbon nanotubes (SWCNT) composites were prepared via solution blending method. Dispersion degree of SWCNT in the composites was characterized by Scanning Electron Microscopy (SEM) and mechanical properties were measured with tensile testing. Thermal degradation of composites was investigated using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). SEM analysis confirmed good dispersion of the nanotubes in the PVB. The tensile tests showed significant increases in mechanical properties such as exceptional improvement in tensile strength, Young's modulus and flexibility for the composites compared to PVB at low SWCNT content.The TGA curves indicated that adding SWCNT improved the thermal stability of the PVB significantly and the degradation of the polymer matrix shifted to the higher temperatures. For the sample containing 0.6 wt%, an increase of 171% in modulus and a 258.4% enhancement of tensile strength were achieved. Also, elongation at break increased 28.7% at this loading. In fact, intrinsic properties of nanotubes caused enhancement of strength and flexibility simultaneously. Also, for this composite, T_onset and T_max enhanced remarkably and weight loss reduced greatly and residue at 600°C increased to high values. These results are promising for application of the PVB in industry.     

The addition of clay on the mechanical properties of surface‐treated CF‐filled PA66 composites

Polyamide 66 (PA66) composites filled with clay and carbon fiber (CF) were prepared by twin‐screw extruder in order to study the influence of nanoparticle reinforcing effect on the mechanical behavior of the PA66 composites (CF/PA66). The mechanical property tests of the composites with and without clay were performed, and the fracture surface morphology was analyzed. The results show that the fracture surface area of the clay‐filled CF/PA66 composite was far smoother than that of the CF/PA66 composite, and there formed a tense interface on the CF surface after the addition of clay. The tensile and flexural strength of CF/PA66 composites with clay was improved. The impact strength decreased because of the high interfacial adhesion. In conclusion, the addition of clay favored the improvement of the higher interface strength and so had good effect on improving the tensile and flexural properties of the composites. Copyright © 2017 John Wiley & Sons, Ltd.     

Bio-Based Nanocomposites of Cellulose Acetate and Nano-Clay with Superior Mechanical Properties

Summary: Bio-based nanocomposites were manufactured by melt intercalation of nanoclays and cellulose acetate (CA) with and without plasticizer. Glycerol triacetate (triacetin) as plasticizer up to 30 mass%, and different types of organo-modified and unmodified montmorillonites (MMTs) as filler were used. X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM), were used to study clay dispersion, intercalation/exfoliation, and structure of the composites. XRD and TEM revealed very good dispersion and exfoliation of modified clay throughout the CA matrix. While for unmodified clay agglomeration and poor dispersion but an intercalated structure was observed. The mechanical properties of injection moulded test bars were determined by a tensile experiment giving tensile strength, Young's modulus and elongation at break. Adding plasticizer facilitated the processing and up to 20 mass%, increased the tensile strength, Young's modulus and elongation at break as well. Higher amount of plasticizer diminished the tensile properties except elongation showing a slight increase. In all plasticized composites, organo-modified clay improved the tensile strength and at the same time, young's modulus and elongation almost remained constant. On the other hand, plasticized CA compounded with unmodified clay revealed lower properties. In a particular case, compounding of unplasticized CA with unmodified clay resulted in superior mechanical properties with a novel structure. So that, in optimum percentage –5 mass%- of unmodified clay, tensile strength and young's modulus increased significantly by 335% and 100%, to 178 MPa and 8.4 GPa, respectively. This is a dramatic improvement in strength and stiffness of CA. Adding organo-modified clay resulted in a little improvement in tensile properties. SEM pictures of the optimum composite showed a core/shell structure with high orientation in the shell part. It is supposed that this behaviour is caused by the interaction between CA hydroxyl groups and free cations existing in the galleries of unmodified clay.     

Mechanical,Thermal and Morphological Behaviors of Castor Oil Based PU/PS Interpenetrating Polymer Network-Metakaolin Composites

The meta kaolin (MK) clay particulate filler with different weight ratios viz., 0, 5, 10, 20 and 30 wt% were incorporated into castable polyurethane (PU)/polystyrene (PS) (90/10) interpenetrating polymer network (IPN). The effects of MK particulate filler loading on the mechanical and thermal properties of PU/PS (90/10) IPN composites have been studied. From the tensile behavior, it was noticed that a significant improvement in tensile strength and tensile modulus as an increase in MK filler content. Thermogravimetric analysis (TGA) data reveals the marginal improvement in thermal stability after incorporation of MK filler. TGA studies of the IPN composites have been performed in order to establish the thermal stability and their mode of thermal degradation. It was found that degradation of all composites takes place in two steps. Degradation kinetic parameters were obtained for the composites using three mathematical models. Tensile fractured composite specimens were used to analyze the morphology of the composites by scanning electron microscopic (SEM) technique.     

Mechanical and thermal properties and flame retardancy of phosphorus-containing polyhedral oligomeric silsesquioxane (DOPO-POSS)/polycarbonate composites

A novel polyhedral oligomeric silsesquioxane containing 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO-POSS) has been incorporated into polycarbonate (PC) composites in order to study its effect on mechanical and thermal properties and flame retardancy. The mechanical and thermal properties of the DOPO-POSS/PC composites have been investigated by tensile and flexural testing, DSC, and DMA. Slight enhancements of yield stress, and flexural strength and modulus, and obvious decreases of fracture strength and strain of the DOPO-POSS/PC composites were observed with an increase in DOPO-POSS loading. The glass transition temperatures (T_g) of the composites were reduced with increasing DOPO-POSS loading. The morphology of the PC composites was evaluated by SEM, which indicated that the DOPO-POSS was dispersed with a particle size of 100-250 nm in the PC matrix. The thermal degradation behaviour and flame retardancies of PC composites with different DOPO-POSS loadings were investigated by TGA, LOI, UL-94 standard, and cone calorimetry. The composite had an LOI value of 30.5 and a UL-94 rating V-0 when the content of DOPO-POSS was 4%.     

Development of continuous process enabling nanofibrillation of pulp and melt compounding

Microfibrillated cellulose (MFC), a mechanically fibrillated pulp mostly consisting of nanofibrils, is a very attractive material because of its high elastic modulus and strength. Although much research has been done on composites of MFC and polypropylene (PP), it has been difficult to produce such composites at an industrial level because of the difficulties in using MFC in such composites are not only connected to the polarity (that can be improved with compatibilizers), but also with the challenge to make a homogeneous blend of the components, and also the low temperature stability of cellulose that could cause problems during processing. We developed a new processing method which enables continuous microfibrillation of pulp and its melt compounding with PP. Never-dried kraft pulp and powdered PP were used as raw materials to obtain MFC by kneading via a twin-screw extruder. Scanning electron microscopy showed nano to submicron wide fibers entangled in the powdered PP. MFC did not aggregate during the melt compounding process, during which the water content was evaporated. Maleic anhydride polypropylene (MAPP) was used as a compatibilizer to reinforce interfacial adhesion between the polar hydroxyl groups of MFC and non-polar PP. We investigated the effect of MAPP content on the mechanical properties of the composite, which were drastically improved by MAPP addition. Needle-leaf unbleached kraft pulp (NUKP)-derived MFC composites had better mechanical properties than needle-leaf bleached kraft pulp (NBKP)-derived MFC composites. Injection molded NUKP-derived MFC composites had good mechanical and thermal properties. The tensile modulus of 50 wt% MFC composite was two times, and the tensile strength 1.5 times higher than that of neat PP. The heat distortion temperature of 50 wt% MFC content composite under 1.82 MPa flexural load was increased by 53 °C, from 69 to 122 °C. This newly developed continuous process using powder resin has the potential for application at an industrial level.     

Physical and mechanical properties of graphene oxide/polyethersulfone nanocomposites

The aim of this study was to investigate physical and mechanical properties of graphene oxide (GO)/polyethersulfone (PES) nanocomposite films. The films were produced by solution casting method. The mechanical properties of composite films were evaluated by tensile test. A significant enhancement in the mechanical properties of neat PES films was obtained incorporating a small amount of GO loading (0.05–1 wt.%). The highest tensile strength was observed at 1 wt.% of GO. Comparisons were made between experimental data and the Halpin–Tsai model predictions for the tensile strength and modulus of GO/PES composites. The effect of an orientation factor on model predictions was also acquired. The hydrophilicity of the nanocomposite was evaluated by assessing contact angle and enhanced wet ability of the films was obtained with increasing the amount of GO up to 1%. The morphology of the nanocomposites was investigated using scanning electron microscopy and transmission electron microscopy and the results revealed a good dispersion of GO in the PES matrix. The thermal behavior of the composite was also studied. Thermal stability of composites was increased by adding the GO. Copyright © 2013 John Wiley & Sons, Ltd.     

Mechanical and thermal investigation of thermoplastic nanocomposite films fabricated using micro- and nano-sized fillers from recycled cotton T-shirts

The thermal and mechanical performance of composites with nano-sized cotton fillers embedded in low-density polyethylene (LDPE) is investigated. Microfibrillated cotton was prepared by microgrinding mechanical treatment of pulverized cotton (pCot) derived from waste T-shirts, resulting in nano-sized fibrils of the cellulose that retain high crystallinity. Film composites of LDPE with pCot before and after microgrinding were fabricated through melt extrusion and the effect of filler size on mechanical, thermal and morphological properties of the composite was investigated. Compounding microfibrillated cotton with LDPE resulted in well-dispersed nanocomposites with no discoloration after 10 min of melt extrusion at 170 °C. At concentrations up to 10 % by weight, the composites showed increased modulus, increased tensile strength and a slight decrease in elongation to break. Further improvement in the dispersion and mechanical properties of the cotton-based fillers was realized by the use of LDPE powder instead of polymer pellets fed to the extruder. This research demonstrates the processing and applicability of the use of recycled cotton-based nano-sized fillers in melt-processing.     

Effect of AlN content on the performance of brominated epoxy resin for printed circuit board substrate

Polymer matrix composites, based on brominated epoxy, a type of material widely used in printed circuit boards (PCBs), as matrix and AlN particle as filler were prepared. The influences of AlN content on the mechanical, thermal, and electrical properties of the composites were investigated by uniaxial tensile test, TMA, thermal conductivity measurement, DMA, and dielectric properties measurement. It was found that the properties of composites monotonically varied with AlN content except that maximum tensile strength and strain of composites corresponded to a filler content of 10 wt %. The results of DMA also showed the AlN reinforcement was more pronounced above T_g, and the peak area of tan δ versus T curves decreased with AlN content, which implied the damping capacity of the composite gradually decreased. The increase in T_g and decrease in damping were probably due to strong interaction between the AlN and epoxy matrix inhibiting the mobility of the epoxy chain. In addition, different theoretical models reported in the literature were used to predict the E, CTE, k, and D_k, and compared with the experimental data. Finally, suitable models were recommended in the present materials system. For the significant improvement of performance of epoxy, we can conclude that these composite materials may be promising for PCB substrate. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1662–1674, 2007     

Improved dielectric and mechanical properties of polystyrene-hybrid silica sphere composite induced through bifunctionalization at the interface

Hybrid silica spheres (HS) of size 270-350 nm with vinyl and aminopropyl surface groups were incorporated in polystyrene (PS), and its effect on dielectric properties, coefficient of thermal expansion (CTE), and strength of PS-HS composite was studied. Incorporation of HS in PS followed a decrease in the dielectric constant from 3.2 for PS to 2.6 for composite with 7.5 vol % HS. The decrease in the dielectric constant was attributed to (i) increased interfacial porosity, (ii) formation of anhydrous HS having low dielectric constant, during hot processing of the composites, and (iii) dispersion and preservation of the anhydrous HS in the hydrophobic matrix. The dielectric constant of the composites with HS content up to 7.5 vol % does not vary much with temperature in the range from -20 to 65 °C. These composites also exhibited reduced CTE and improved flexural strength/stiffness due to good interfacial bonding through HS vinyl groups and dispersion of the filler in the matrix. The dielectric loss increased with HS content, and the loss measured for 7.5 vol % PS-HS composite was 6 × 10(-3), as compared to 10(-4) for PS. At HS loading above 7.5 vol %, the tendency of HS to agglomerate and form percolated structure lead to an increase in the dielectric constant and decrease in the mechanical properties of the composites.     

Effect of nano‐modified SiO2/Al2O3 mixed‐matrix micro‐composite fillers on thermal,mechanical, and tribological properties of epoxy polymers

Thermo‐mechanically durable industrial polymer nanocomposites have great demand as structural components. In this work, highly competent filler design is processed via nano‐modified of micronic SiO₂/Al₂O₃ particulate ceramics and studied its influence on the rheology, glass transition temperature, composite microstructure, thermal conductivity, mechanical strength, micro hardness, and tribology properties. Composites were fabricated with different proportions of nano‐modified micro‐composite fillers in epoxy matrix at as much possible filler loadings. Results revealed that nano‐modified SiO₂/Al₂O₃ micro‐composite fillers enhanced inter‐particle network and offer benefits like homogeneous microstructures and increased thermal conductivity. Epoxy composites attained thermal conductivity of 0.8 W/mK at 46% filler loading. Mechanical strength and bulk hardness were reached to higher values on the incorporation of nano‐modified fillers. Tribology study revealed an increased specific wear rate and decreased friction coefficient in such fillers. The study is significant in a way that the design of nano‐modified mixed‐matrix micro‐composite fillers are effective where a high loading is much easier, which is critical for achieving desired thermal and mechanical properties for any engineering applications. Copyright © 2016 John Wiley & Sons, Ltd.