电感耦合等离子体发射光谱法测定REACH法规涉及产品中铅、铬、钴、砷、锡、铝、锆、钼和硼

采用电感耦合等离子体原子发射光谱法对REACH法规涉及产品中铅、铬、钴、砷、锡、铝、锆、钼和硼的含量进行测定。0.2g样品经微波消解处理,聚合物材质试样以8mL硝酸和2mL过氧化氢为消解试剂;无机非金属材质试样以6mL硝酸、2mL过氧化氢和2mL氢氟酸为消解试剂。各元素的方法检出限均低于15mg·kg-1。方法的加标回收率在82.4%～108%之间,测定值的相对标准偏差(n=7)在3%～6%之间。     

固相萃取-气相色谱法测定水体中2,4-滴和灭草松的残留量

提出了固相萃取-气相色谱法测定水体中2,4-滴和灭草松残留量的方法。用硝酸将1.0 L水样酸度调至pH小于2,然后以6.0 mL·min^-1流量过活化好的HLB pro固相萃取柱，用10.0 mL水淋洗，再用10.0 mL乙酸乙酯洗脱。收集洗脱液，氮吹至近干，加入500μL N,N-二甲基甲酰胺二甲缩醛和1.0 mL正己烷，于160℃衍生50 min。衍生结束后，取出，冷却至室温，加入2.0 mL饱和氯化钠溶液，待分层后，取0.8 mL上层有机相过0.22μm有机相滤膜，滤液按照仪器工作条件进行测定。结果表明：2,4-滴和灭草松的衍生产物分别为2,4-滴甲酯和灭草松甲酯；2,4-滴和灭草松的质量浓度在0.01～0.50 mg·L^-1内与对应的衍生产物峰面积呈线性关系，检出限(3.143s)为0.003～0.010μg·L^-1;对实际加标样品进行精密度试验，测定值的相对标准偏差(n=6)均小于7.0%;生活饮用水、地表水、城镇污水和海水加标样品中，目标物回收率为81.3%～95.4%。     

二阶导数-同步荧光法同时测定微量维生素B_1,B_2和烟酰胺

建立了二阶导数-同步荧光法同时测定微量维生素B1,B2和烟酰胺含量的方法.在最佳实验条件下,维生素B1,B2和烟酰胺的检测限分别为2.1,2.6,和2.8 ng/mL,相对标准偏差为1.5%～4.9%,加标回收率为92%～105%.该方法可用于样品中微量维生素的测定.     

电感耦合等离子体发射光谱法测定不锈钢中的铬、镍、锰、铜、钛、铝

建立电感耦合等离子体发射光谱仪同时测定不锈钢中铬、镍、锰、铜、钛、铝6种元素含量的方法。用20mL王水溶解样品,铬、镍、锰、铜、钛、铝的分析谱线分别为283.563,231.604,259.373,324.754,334.941,308.215 nm。铬、镍、锰、铜、钛、铝的质量浓度与其信号强度均呈良好的线性关系,线性相关系数均不小于0.999,检出限分别为0.007,0.009,0.002,0.007,0.002,0.008μg/mL。测定结果的相对标准偏差为0.17%～2.80%(n=6),加标回收率为96.50%～103.70%。用该法测定国家标准物质,测定值与标准值一致,相对误差为0.05%～3.03%。该方法准确、可靠,可用于不锈钢中铬、镍、锰、铜、钛、铝的测定。     

微波消解–ICP–MS法测定格隆溴铵注射液中的铬、镍、钼

建立了电感耦合等离子体质谱法测定格隆溴铵注射液中铬、镍、钼3种残留金属元素的方法。分别在0,500,1 200 W功率下,样品采用硝酸和过氧化氢混合溶液微波消解,在选定的仪器工作条件下测定。铬、镍、钼的质量浓度在5～200 ng/mL范围内具有良好的线性关系,相关系数不小于0.995,方法检出限为0.22～0.49 ng/mL,定量限为1.08～2.46 ng/mL。测定结果的相对标准偏差为1.4%～3.0%(n=11),样品加标回收率为92.88%～111.94%。该方法操作简单、快速,结果准确、可靠,适用于格隆溴铵注射液中铬、镍、钼的测定。     

气质联用法测定复合食品包装袋中的二氨基甲苯

建立复合食品包装袋中二氨基甲苯气相色谱一质谱测定方法.样品用4%乙酸提取,加三氟乙酸酐进行衍生化,用气相色谱-质谱联用仪测定.二氨基甲苯含量在0. 002～0. 05μg/mL范围内与离子蜂面积呈良好的线性关系,相关系数r=0. 9998,检出限低于0. 0004 mg/L.测定结果的相对标准偏差为2. 98%～5. 50%(n=6),加标回收率为82%～92%.该方法快速、灵敏、测定结果准确.     

微波消解-微波等离子体炬原子发射光谱法测定合金钢中的铜、锰、钼

用微波等离子体炬 (MPT)为激发光源 ,氩气为等离子体工作气体 ,用气动雾化进样 ,研究了微波消解 微波等离子体炬原子发射光谱法 (MPT AES)测定合金钢中铜、锰、钼的方法。考察了微波功率、载气流量、工作气流量、氧屏蔽气流量等实验参数对测定铜、锰、钼的影响。对微波消解合金钢样品的消解条件进行了考察 ,建立了最佳消解程序。测定铜、锰、钼的检出限分别为 3.3、3.7和 42ng mL ,RSD(n =6)分别为 1 7%、2 .4%、3.8% ,并且测得它们的线性范围分别为0 .0 2～ 5 0 μg mL、0 .0 4～ 5 0 μg mL和 0 .2 0～ 5 0 μg mL。     

离子色谱法同时测定蛋白胨中氯离子、硫酸根离子、碘离子

建立离子色谱法测定蛋白胨中氯离子、硫酸根离子、碘离子3种阴离子的含量。采用氢氧化钾淋洗液发生器产生的KOH溶液为流动相,进行梯度淋洗,流量为1.0 mL/min。氯离子、硫酸根离子的质量浓度分别在0.5～200μg/mL范围内与色谱峰面积呈良好的线性关系,碘离子的质量浓度在0.75～50μg/mL范围内与色谱峰面积呈良好的线性,线性相关系数均不小于0.999,检出限分别为0.003,0.01,0.22μg/mL。样品加标回收率为92.94%～96.59%,测定结果的相对标准偏差为2.42%～5.70%(n=9)。该方法灵敏、高效,可用于蛋白胨中氯离子、硫酸根离子、碘离子的快速准确测定。     

氢化物发生器/冷原子吸收光谱法测定涂料中汞

建立了使用流动注射氢化物发生器、KBH4-H2SO4体系使汞还原气化,采用冷原子吸收分光光度法测定涂料中汞的分析方法.在吸收波长253.7nm处,汞在0～100ng/mL呈现良好的线性关系,标准曲线的回归方程C=128.640A-3.9200,相关系数γ=0.9994;以3SA/S计,方法检出限:0.8ng/mL;方法精密度RSD<5%.加标回收率在95%～108%.方法自动化程度高,用于涂料中汞的测定,简便、快捷、准确.     

钙、镁、铁、铝离子对土壤中总氟化物检测干扰的消除

建立钙、镁、铁、铝离子对离子选择电极法检测土壤总氟化物干扰的消除方法。通过对含不同浓度水平钙、镁、铁、铝离子的土壤样品中总氟化物进行测试,明确了在总离子强度调节缓冲溶液共存下钙、镁、铁、铝离子对土壤提取液中总氟化物检测结果存在负干扰。通过测试10种土壤样品总氟化物提取液中干扰最强的背景铝含量,对其中土壤提取液中铝离子质量浓度大于10.0 mg/L的3种土壤样品进行加标回收试验,结果表明了土壤总氟化物含量为327～926 mg/kg范围内,当样品提取液中的铝离子含量为50～100 mg/L时,通过减少提取液取样体积为5.00 mL并增加柠檬酸三钠总离子强度缓冲溶液体积至15.0 mL的方法可将加标回收率由56.4%～78.3%优化至94.7%～104.0%;当加入Ca~(2+),Mg~(2+),Fe~(3+)质量浓度为200～300 mg/L,加标回收率由63.1%～77.6%优化为92.4%～105.0%。用优化后的方法测定土壤总氟化物含量为246～2 240 mg/kg的5种标准样品,测试结果与标准值一致。该方法能有效地消除土壤样品总氟化物测定中含钙、镁、铁离子质量浓度为200～300 mg/L,铝离子质量浓度为50～100 mg/L而产生的干扰,具有良好的适用性。     

Optimization of parameters for semiempirical methods. III Extension of PM3 to Be,Mg, Zn,Ga, Ge,As, Se,Cd, In,Sn, Sb,Te, Hg,Tl, Pb,and Bi

Using a recently developed procedure for optimizing parameters for semiempirical methods,¹ PM3 has been extended to a total of 28 elements. Average ΔH_f errors for the newly parameterized elements are Be: 8.6, Mg: 8.4, Zn: 5.8, Ga: 14.9, Ge: 11.4, As: 8.5, Se: 11.1, Cd: 2.6, In: 11.3, Sn: 9.0, Sb: 13.7, Te: 11.3, Hg: 6.8, Tl: 6.5, Pb: 7.4, and Bi: 10.9 kcal/mol. For some elements the paucity of data has resulted in a method, which, while highly accurate, is likely to be only poorly predictive.     

Thin-layer chromatographic separation of aldrin,dieldrin, γ-hexachlorocyclohexane,malathion, ethyl-parathion,pentachlorophenol, and of chlordane,dieldrin, γ-hexachlorocyclohexane,malathion, ethyl-parathion,and pentachlorophenol from each other

A thin-layer chromatographic method is reported for the separation of aldrin (or chlordane), dieldrin, γ-hexachlorocyclohexane, malathion, ethyl-parathion, and pentachlorophenol from each other. The procedure, however, does not separate aldrin and chlordane from each other although it does separate either pesticide from the other components. The method employs alumina plates with n-hexane:xylene:benzene:toluene:cyclohexane:methyl cyclohexane (50:50:50:50:50:50:) as developing solvent.     

Certification of the mass fractions of Ca,Cu, Cl,I, Fe,K, Mg,P, Pb,N, Na and Zn in skim milk powder

Analyses of milk and milk products are routinely performed by a number of dairy laboratories to control the quality of these products with regard to e.g. nutritional components and potential exposure to toxic elements. In order to improve and control the quality of such analyses the Community Bureau of Reference (BCR) has organized series of certification campaigns to produce reference material of milk certified for a variety of elements and compounds. The increasing demand is such that the stock of some of these materials is now exhausted. Consequently, the BCR decided to produce a new batch of CRM of skim milk powder certified for its contents of Ca, Cu, Cl, I, Fe, K, Mg, P, Pb, N, Na and Zn (CRM 063R). This material was carefully prepared (spray-drying) and its homogeneity and long term stability was verified. This paper presents the certification work performed.     

Stereochemistry of the oxidation of 1, 2, 3, 5, 6, 7, 8, 8a-octahydro-1-naphthoic acids

Summary It was shown that the oxidation of syn- and anti-1,2,3,5,6,7,8,8a-octahydro-1-naphthoic acids with peroxyacetic acid and with osmium tetraoxide proceed stereospecifically from the side opposite to that of the carboxy group. On the other hand, the oxidation of syn-cis-1,2,3,5,6,7,8,8a-octahydro-1, 2-naphthalenedicarboxylic acid goes in both of the possible sterically different directions with formation of isomeric- and-epoxides.     

Prediction of the enthalpy of vapourisation for anhydrides,formates, acetates,propionates, butyrates,esters, and ethers

Four analytical correlations based on the use of the corresponding states principle were used to calculate the enthalpy of vapourisation of fluids. Three of these correlations require as inputs the critical temperature and the acentric factor. The fourth requires a molecular Lennard–Jones parameter and the acentric factor. Results for 184 polar and non-polar fluids grouped into 9 families are compared with the values accepted by the Design Institute for Physical Property (DIPPR) project. Recommendations are given for the use of each model and for the choice of the adequate model for each family of fluids.     

Certification of the contents of As, B, Cd, Cr, Co, Cu, Mn, Hg, Ni, Ti, V and Zn in a natural Moroccan phosphate rock

Summary The preparation and homogeneity tests of a natural Moroccan phosphate rock are described. The experimental procedures leading to the certification of the contents of As, B, Cd, Cr, Co, Cu, Hg, Mn, Ni, Ti, V and Zn are presented. The Pb-content is given as a recommended value. Indicative values are proposed for Ag, Mo, Sb, Se, Th and U. The certification has been carried out in participation with 11 laboratories from different European countries.

---

Zertifizierung der Gehalte an As, B, Cd, Cr, Co, Cu, Mn, Hg, Ni, Ti, V und Zn in einem natürlichen Marokkanischen Phosphatgestein

Zusammenfassung Die Aufbereitung und die Homogenitätskontrollen eines natürlichen Marokkanischen Phosphatgesteins werden beschrieben. Die experimentellen Arbeiten, die zur Zertifizierung der genannten Gehalte geführt haben, werden angegeben. Für Blei wird ein empfohlener Wert gegeben. Indikative Werte werden für Ag, Mo, Sb, Se, Th und U vorgeschlagen. Die Zertifizierung wurde in Zusammenarbeit mit 11 Laboratorien aus verschiedenen europäischen Ländern durchgeführt.

     

ICP-AES法测定铝中铁、硅、铜、镓、镁、锌、锰和钛

用 50g L氢氧化钠溶液溶解铝样品 ,硝酸 (1 1 )酸化 ,以ICP AES测定其中铁、硅、铜、镓、镁、锌、锰和钛等 8种杂质元素。     

ICP-MS测定化妆品中铍、镉、铊、铬、砷、碲、钕、铅

目的：建立化妆品中铍、镉、铊、铬、砷、碲、钕、铅8种有害元素的测定方法。方法：采用电感耦合等离子体质谱法,样品采用微波消解,以钇、锂、铟、铋为内标作定量分析。结果：各元素和内标元素在一定浓度范围内的质量数比值均与浓度呈良好的线性关系,线性方程的相关系数均大于0.9998,平均回收率为95%~104%,相对标准偏差(RSD)均小于3%。结论：该方法灵敏度高,准确,可为化妆品中上述元素的限量检查提供参考。