对-RTlnKco=ΔrGmo(T,co)的理论探讨

应用热力学特性函数、齐次函数定理和勒让德变换等概念和方法从理论上探讨了热力学公式RTlnKco=ΔrGmo（T,co）在推导和应用方面的问题。严格的数学论证表明该式是背离热力学原理的,它近似地适用于液相,但应用于气相则可能产生较大偏差。     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Af-AaDd型氢键体系的网络结构参数

利用溶胶-凝胶分配理论对氢键溶液的模型体系进行研究, 给出了凝胶点后氢键网络中各结构参数的计算方案, 并进行相应的数值计算. 结果表明, 因受体基团本身的性质及两类质子受体基团的数量比不同, 受体基团的竞争作用对网络结构有明显影响, 这提供了控制氢键网络结构特征的可能方法.     

Zr1-xMxWMoO8-x/2和Zr1-xMxW2O8-x/2固溶体的晶胞参数与晶格畸变的关系

合成了Zr1-xMxWMoO8-x/2(M=Er,Tm,Yb,Sc,In,Ga,Al)和Zr1-xMxW2O8-x/2(M=Eu,Er,Yb,Sc,In,Ga,Al)2个系列的固溶体,前者具有β-ZrW2O8结构类型(简称β相);后者具有α-ZrW2O8结构类型(简称α相)。建立了相和相的晶胞参数与M3+离子浓度的Vegard方程,测定了上述固溶体的固溶度。讨论了M3+离子的化学性质与Vegard斜率SV的关系。分析了α相的SαA与β相的SβA的关系;揭示了α-Zr1-xMxW2O8-x/2晶格中2[WO4]四面体对的取向有序程度对晶格畸变的贡献。提出上述固溶体的晶胞参数随溶质浓度增加而减小,主要是由于氧空位缺陷相互作用的结果。     

CexZr1-xO2/Co/C-N催化CO2加氢性能研究

将不同比例的铈锆前驱体负载到ZIF-67,氮气气氛焙烧制备CexZr1-xO2/Co/C-N催化剂,对催化剂进行了XRD,H2-TPR、XPS表征,并在固定床反应器评价其CO2加氢制甲醇性能。XRD结果表明,在铈中加入适量锆形成铈锆固溶体,铈锆固溶体与钴物种较强的相互作用力可以阻止表明金属Co的氧化。但过量加入的锆又会削弱这一作用力,部分金属Co被氧化为Co3O4。H2-TPR结果表明适量的锆的加入改善催化剂的还原性能,催化剂还原温度降低。XPS证实了25%Ce0.67Zr0.33O2/Co/C-N催化剂中含有更多的氧空穴及氮含量,氧空穴和碱性氮都有利于CO2的解离吸附。优化后的25%Ce0.67Zr0.33O2/Co/C-N 催化剂在225 oC,2 MPa,GHSV = 6 L/gcat/h反应条件下取得最高甲醇时空收率,为3.0 mmol/gcat/h。     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

nFe3+/nSr2+和nOH-/nNO3-对锶铁氧体纳米片结构及磁性能的影响

采用改进的水热法成功合成了单分散的纯相锶铁氧体纳米片。借助DLS、XRD、FTIR、SEM、EDS和VSM等分析测试手段对SrFe₁₂O₁₉铁氧体粉体的粒度、结构、形貌和磁性能进行表征。研究结果表明,在240℃保温5 h,物质的量之比n_Fe³⁺/n_Sr²⁺(R_F/S)和n_OH^-/n_NO^-(R_O/N)分别为5和2时,所得产物为单分散的纯相六角SrFe₁₂O₁₉铁氧体纳米片。随着R_F/S和R_O/N的变化,合成样品中有少量SrCO₃和Fe₂O₃杂相存在,这主要与反应条件和离子比例有关。磁性能测试结果显示,所得纯相的六角SrF₁₂O₁₉铁氧体纳米片具有优异的磁性能,其饱和磁化强度和矫顽力分别达到60.91 emu·g^-1和94.83 kA·m^-1,使其在医疗、催化和生物等高技术领域具有潜在的应用。     

钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

Photoinduced charge property of Ag‐TiO2 films and its relationships with photocatalytic activity under visible illumination

In this article, TiO₂ films were synthesized by traditional spin coating method. To improve their photocatalytic activities, we deposited silver on these films by photodeposition. These films also were characterized by several testing techniques, such as X‐ray diffraction, ultraviolet–visible diffuse reflection spectrum, XPS, Raman spectroscopy (Raman), surface photovoltage spectroscopy, and SEM. The activity of different films was evaluated for degrading rhodamine B solution under visible illumination. The effects of AgNO₃ solution concentration on photoinduced charge property and photocatalytic activity were investigated. The results show that the Ag‐TiO₂ film immersed in 10^?3 mol·L^?1 AgNO₃ solution exhibits higher activity, which is in good agreement with the characterization results. The weaker the surface photovoltage spectroscopy signal, the higher the photocatalytic activity. Moreover, the activity of some films is higher than that of international Degussa P‐25 TiO₂ under visible illumination. Copyright © 2012 John Wiley & Sons, Ltd.     

Ag3PO4的可见光光催化性能及机理分析

采用沉淀置换法制备了可见光光催化剂Ag3PO4,利用XRD、UV-Vis及XPS等对其进行了结构特性分析,以水中微污染有机物的降解评价了Ag3PO4的光催化活性,并通过活性物种及能带结构的分析对催化剂的光催化机理进行了推测。结果表明,Ag3PO4的带隙能约为1.9 eV、催化剂表面存在的Ag+可捕获光生e-、催化剂的价带电位较低,这有利于Ag3PO4在可见光照射下产生的e--h+的分离及活性物种.OH的形成。经60 min可见光光催化反应,15 mg.L-1的甲基橙和腐殖酸的降解率分别达97%和82%,比同等条件下TiO2-P25的降解率还高40%和25%,光催化剂Ag3PO4的用量为0.6 g.L-1。     

掺镁钛酸钡纳米棒的水热合成和光催化性能

用水热法制备掺镁钛酸钡(Ba1-xMgxTiO3(x=0,0.10,0.20,0.30,0.40),BMT)纳米粉体。运用X射线衍射仪(XRD)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、紫外可见漫反射光谱技术(DRS)等手段对样品进行了表征,并在可见光照射下于溶液中考察了其光催化降解甲基橙反应活性。结果表明,通过控制氢氧根浓度可以得到不同形貌的纳米粉体。基于不同条件下制备的样品的微结构分析,提出了这些不同形貌的形成机制。制备出的BMT材料的带隙能约为2.61 eV。光催化反应结果表明BMT的光催化活性比掺氮TiO2高得多。OH-浓度为8 mol·L-1时制备的BMT纳米棒光催化效率最高,经可见光照射360 min,浓度为0.01 mmol·L-1甲基橙溶液的降解率可达到93.0%,且循环使用4次后,其光催化活性并没有明显降低,表明BMT是一种稳定有效的可见光催化剂.     

Photocatalytic Oxidation of Aniline in the Gas Phase Using Porous TiO2 Thin Films

The gas-phase photocatalytic oxidation of aniline on a new kind of porous nano-TiO₂ composite films is investigated. The composite film was prepared on glass fiber with the water glass as binders and dilute H₂SO₄ solution as solidifying reagent. The surface characters were observed by scanning electron microscope. The photocatalytic degradation of aniline on the composite films was carried out in a TiO₂/UV system. Some important factors affecting the photodegradation, such as the concentration of TiO₂, the initial concentration of aniline, and the existing water vapor, are also studied. The product of photocatalytic oxidation was detected by Fourier transform-Infrared. The partial intermediate products were absorbed on TiO₂ surface, which resulted in catalyst deactivation. But when it was irradiated under UV illumination or solar irradiation for some time, the catalyst could be reused without loss of catalytic activity. Translated from the Journal of Wuhan University (Natural Science Edition), 2005, 51(2) (in Chinese)     

Cu、N共掺杂TiO2纳米管光催化重整甘油制备合成气

通过碱性水热-离子交换法制备了Cu、N共掺杂TiO₂纳米管(Cu/N-TNT),对其光催化重整甘油制备合成气性能进行了研究。结果表明,Cu/N-TNT具有富含氧空位(O_V)的管状结构,N以Ti-N形式取代部分O形成杂质能级,Cu以Cu²⁺形式掺杂在催化剂晶格间隙和表面,Cu、N共掺杂促进TiO₂表面电荷有效分离,有利于其光催化重整甘油制备合成气活性和选择性的提高。紫外光照射8 h时,掺Cu量为0.15%的Cu/N-TNT催化剂上CO和H₂产量分别为7.3和8.5 mmol·g^-1,是原始TiO₂的9.1和70.8倍,n_H2/n_CO从0.52提高为1.18,n_CO/n_CO2从0.21提高至0.42。Cu/N-TNT表面N和O_V为醛类脱羰和甲酸脱水生成CO提供反应活性位点,Cu作为浅势阱提高光生电子-空穴分离效率。光生空穴(h⁺)是光催化重整甘油制备合成气过程中的主要活性物种,大量羟基自由基(·OH)和超氧自由基(·O₂^-)会导致甘油过度氧化,使CO选择性降低。     

Synthesis of anatase TiO2 in a vinyl-containing ionic liquid and its enhanced photocatalytic activity

TiO₂ microspheres were synthesized by the sol–gel method using the ionic liquid (IL) 1-vinyl-3-propylimidazolium iodide (VPIM⁺I^?) as a reaction medium, then calcined at 500 °C. The samples were characterized by X-ray diffraction, scanning electron microscopy, and ultraviolet–visible (UV–Vis) diffuse reflectance spectroscopy. The phase of TiO₂ microspheres is anatase, and VPIM⁺I^? is able to favor the growth of anatase phase and prevents the collapse of small pores. The photocatalytic activity of TiO₂-IL was tested by degradation of 2-nitrophenol under UV light illumination. The photocatalytic activity of TiO₂-IL was higher than that of samples prepared in the reaction medium without VPIM⁺I^?.     

三维Cu-MOF对亚甲蓝的吸附和光催化降解及其机理

本文报道了[Cu₃(ppda)₃(tib)₂(H₂O)₄]·6H₂O(Cu-MOF)的合成、结构、吸附和光催化降解性能。在Cu-MOF中,1,4-苯二乙酸(H₂ppda)和1,3,5-三(1-咪唑基)苯(tib)配体交替连接Cu离子形成二维层,层与层之间通过trans-ppda^2-相互穿插形成稳定的三维结构。Cu-MOF对亚甲蓝(MB)的催化效率为97%,最高反应速率常数为0.019 7 min^-1。光催化降解机理：在光的激发下,催化剂表面的光生电子和空穴对发生分离,并与O₂、H₂O、H₂O₂反应生成活性物质,将染料降解为CO₂和H₂O。在MB溶液中加入NaCl(200 g·L^-1)后,Cu-MOF的吸附量有所提升(87.23 mg·g     

三维Cu-MOF对亚甲蓝的吸附和光催化降解及其机理

本文报道了[Cu₃(ppda)₃(tib)₂(H₂O)₄]·6H₂O (Cu-MOF)的合成、结构、吸附和光催化降解性能。在Cu-MOF中，1，4-苯二乙酸(H₂ppda)和1，3，5-三(1-咪唑基)苯(tib)配体交替连接Cu离子形成二维层，层与层之间通过trans-ppda^2-相互穿插形成稳定的三维结构。Cu-MOF对亚甲蓝(MB)的催化效率为97%，最高反应速率常数为0.019 7 min^-1。光催化降解机理：在光的激发下，催化剂表面的光生电子和空穴对发生分离，并与O₂、H₂O、H₂O₂反应生成活性物质，将染料降解为CO₂和H₂O。在MB溶液中加入NaCl (200 g·L^-1)后，Cu-MOF的吸附量有所提升(87.23 mg·g^-1)，准二级动力学模型和Langmuir等温线模型的实验数据拟合程度较好，该吸附的主要过程为单层化学吸附。     

Cu、N共掺杂TiO2纳米管光催化重整甘油制备合成气

通过碱性水热-离子交换法制备了Cu、N共掺杂TiO₂纳米管(Cu/N-TNT),对其光催化重整甘油制备合成气性能进行了研究。结果表明,Cu/N-TNT具有富含氧空位(O_v)的管状结构,N以Ti-N形式取代部分O形成杂质能级,Cu以Cu²⁺形式掺杂在催化剂晶格间隙和表面,Cu、N共掺杂促进TiO₂表面电荷有效分离,有利于其光催化重整甘油制备合成气活性和选择性的提高。紫外光照射8h时,掺Cu量为0.15%的Cu/N-TNT催化剂上CO和H₂产量分别为7.3和8.5 mmol·g^-1,是原始TiO₂的9.1和70.8倍,n_H2/n_CO从0.52提高为1.18,n_CO/n_CO2从0.21提高至0.42。Cu/N-TNT表面N和O_V为醛类脱羰和甲酸脱水生成CO提供反应活性位点,Cu作为浅势阱提...     

Ensembles of indium and gallium fluoroanions with HF molecules and bipyridine cations

Compounds [H₂L¹][Ga(H₂O)₂F₄]₂ · H₂O (I), [H₂L¹] _n [InF₅] _n · (2HF) _n (II), and [H₂L₂][In(H₂O)F₅] · HF (III) were identified as the major phases in the products of the reactions between MF₃ · 3H₂O (M = Ga, In) and ditopic bases 4,4′-trimethylenedipyridine (L¹) and 4,4’-trimethylenedipiperidine (L²) in HF solutions under common and hydrothermal conditions.