核-壳结构Cu/Al微纳米复合材料与WO3的热反应性能

采用置换法通过对溶液浓度的控制实现了纳米Cu颗粒在微米Al粉表面定量、快速地化学沉积, 制备出核-壳结构的Cu/Al微纳米复合粒子, 并用SEM、EDS和XRD技术进行表征. 在此基础上, 利用DSC 分析了Cu/Al-WO3的热反应性能, 对比了Al-WO3与Cu/Al-WO3在不同化学配比下的热反应历程, 同时分别提出了其相应的反应机理. 实验结果表明, Cu/Al微纳米复合材料与WO3的热反应活性明显高于传统微米级Al粉, 并且在还原剂Cu/Al轻微过量时该热反应达到最佳效果. 通过对Al粉表面改性, 热反应的活化能降低了68.185 kJ·mol-1.     

纳米镍包覆超细铝复合粉末的氧化性能

通过置换还原法, 快速、简洁、定量地制备出了纳米镍包覆的超细铝粉复合粉末. 利用扫描电子显微镜(SEM)、热重分析(TGA)、差示扫描量热(DSC)和X射线衍射(XRD)等分析手段对原料Al粉和复合粉末的形貌及其氧化性能进行研究. 结果表明, 原料Al粉在1050 ℃时增重率为122%, 当包覆的纳米镍粉质量分数为0.75%时, 可以使铝粉在1050 ℃时的增重率达到135%, 并且随着镍粉含量的增加, 铝粉的增重率进一步提高. 当镍的质量分数达到8.93%时, 复合粉末在约1000 ℃时出现点火燃烧现象. 纳米镍粉的氧传递对促进超细铝粉的氧化起到了至关重要的作用.     

超细核壳铜-银双金属粉的制备

本文采用置换反应法制备得到了球形、粒径约 50纳米的核壳铜 -银双金属粉末 ,经 X射线衍射和热重分析测试确定其结构为表面点缀结构和完全包覆结构。并用透射电子显微镜和 X射线荧光光谱仪对粉末的形貌和组成进行了测定。     

中空介孔碳化钨微球载钯催化剂对甲酸电催化性能

采用喷雾干燥法和还原炭化处理制备具有中空介孔结构的碳化钨钴复合粉(HTCCS),其中,钴的质量含量为6%。在碳化钨钴复合粉表面的钴和氯化钯发生置换反应,得到纳米Pd/WC复合催化剂。采用X射线粉末衍射(XRD)、扫描电镜(SEM)和透射电镜(TEM)对样品的形貌和晶型结构进行了表征。结果表明, 5.0-6.0nm钯纳米粒子取代钴均匀分布在碳化钨微球表面。采用循环伏安和计时电流法研究了在酸性溶液中Pd/WC催化剂对甲酸的电催化氧化性能,结果表明,Pd/WC催化剂比Pd/C催化剂对甲酸呈现出更高的电催化氧化活性和稳定性。     

中空介孔碳化钨微球载钯催化剂对甲酸电催化性能（英文）

采用喷雾干燥法和还原炭化处理制备具有中空介孔结构的碳化钨钴复合粉(HTCCS),其中,钴的质量含量为6%。在碳化钨钴复合粉表面的钴和氯化钯发生置换反应,得到纳米Pd/WC复合催化剂。采用X射线粉末衍射(XRD)、扫描电镜(SEM)和透射电镜(TEM)对样品的形貌和晶型结构进行了表征。结果表明,5.0-6.0 nm钯纳米粒子取代钴均匀分布在碳化钨微球表面。采用循环伏安和计时电流法研究了在酸性溶液中Pd/WC催化剂对甲酸的电催化氧化性能,结果表明,Pd/WC催化剂比Pd/C催化剂对甲酸呈现出更高的电催化氧化活性和稳定性。     

电化学置换法制备高Pt利用率的类核壳型Ni-Pt电催化剂(英文)

采用电化学置换法,在VulcanXC-72表面制备得到了活性高和分散性好的纳米Ptshell-Nicore电催化剂.该方法先以NaH2PO2为还原剂,化学沉积得到Ni核,Pt在Ni核表面通过原位置换形成Ni-Pt类核壳型结构.通过透射电镜(TEM)、X射线衍射(XRD)、紫外-可见光光谱(UV-Vis)和循环伏安(CV)测试证明了Pt壳层完全包覆在Ni核的表面.电化学氢吸/脱附测试结果显示,Ptshell-Nicore/XC-72的电化学活性面积为Pt/C(JM)的1.2倍,而其理论Pt担载量只为Pt/C(JM)的40%.这表明,核壳型Ni-Pt纳米粒子可以显著提高Pt的催化活性和利用率.     

新型室温酯化法接枝聚合物改性SiO_2纳米微粒

提出了一种在室温、大气环境等温和条件下通过酯化反应将端羧基聚合物链接枝到纳米SiO2微球表面从而制备有机/无机复合纳米微粒的新方法.该方法通过以下两个步骤得以实现,即第一,用3-环氧丙基三甲氧基硅烷对纳米SiO2微球表面进行改性处理,接着将引入到纳米SiO2表面的环氧基团转化为烷羟基基团;第二,通过引入到纳米SiO2微球表面的烷羟基与聚合物中的端羧基在室温下发生酯化反应,从而将聚合物接枝到纳米SiO2表面制得复合微球.利用XPS、FTIR、TEM和TGA等测试手段对纳米SiO2的改性过程以及聚合物接枝后得到的复合微球进行了表征.研究结果表明,该室温酯化接枝方法具有较高的接枝率,接枝到无机纳米微粒表面的聚合物占复合微球质量的55wt%～70wt%;接枝聚合物后,纳米SiO2微球的粒径从40nm增加到64～75nm,从而得到了以SiO2为核、以聚合物为壳的有机-无机复合微球.     

银/铂双金属中空纳米颗粒的制备及光学性质研究

通过以Ag纳米颗粒为模板的置换和沉积反应,制备了Ag/Pt双金属复合纳米颗粒.用透射电子显微镜(TEM)对颗粒的形貌、尺寸和结构进行了表征,发现复合颗粒具有中空结构.紫外可见吸收光谱(UV-Vis)研究表明,Ag/Pt双金属中空复合纳米颗粒具有单峰的表面等离子共振吸收特征,随着反应溶液中氯铂酸和硝酸银摩尔比的增加,吸收峰先红移后蓝移.表面增强拉曼光谱实验结果表明,Ag/Pt双金属复合纳米颗粒对吡啶分子具有较好的增强效果.     

CdTe纳米晶-BaSO4复合荧光微球的制备

利用表面活性剂双层修饰技术在水溶性荧光CdTe纳米晶表面先后包覆了双十八烷基二甲基溴化铵和十二烷基硫酸钠, 从而在纳米晶外表面引入—SO-4反应位点, 以—SO-4为活性中心进一步制备了包覆CdTe纳米晶的BaSO4复合荧光微球. 通过扫描电子显微镜、透射电子显微镜、共聚焦荧光显微镜和X射线粉末衍射等方法确定了复合微球的尺寸及组成. 由于BaSO4的保护, CdTe-BaSO4复合微球荧光的耐酸性比CdTe原液的提高明显.     

二氧化硅-聚丙烯腈核-壳结构复合纳米粒子的制备与表征

以甲基丙烯酸-3-(三甲氧基硅基)丙酯改性的SiO2纳米粒子为种子,采用乳液聚合法制备了粒径分布较窄的SiO2-聚丙烯腈(SiO2-PAN)核-壳结构复合纳米粒子。采用动态光散射、傅里叶红外光谱、透射电镜和扫描电镜表征了复合纳米粒子的粒径及分布、组成、形态和结构,并研究了表面活性剂的加入方式、反应温度及交联剂的引入对制备SiO2-PAN复合纳米粒子的影响。结果表明:SiO2-PAN复合纳米粒子为核-壳结构。采用半连续加入表面活性剂的方法,可以成功抑制乳液聚合中次级粒子的生成。通过增加表面活性剂的初始加入量、加快表面活性剂的补加速率,或降低反应温度,可使SiO2-PAN复合纳米粒子的粒径变小。反应温度的降低以及交联剂的引入使SiO2-PAN复合纳米粒子的表面变得平滑。     

Dependence of size and size distribution on reactivity of aluminum nanoparticles in reactions with oxygen and MoO3

The oxidation reaction of aluminum nanoparticles with oxygen gas and the thermal behavior of a metastable intermolecular composite (MIC) composed of the aluminum nanoparticles and molybdenum trioxide are studied with differential scanning calorimetry (DSC) as a function of the size and size distribution of the aluminum particles. Both broad and narrow size distributions have been investigated with aluminum particle sizes ranging from 30 to 160 nm; comparisons are also made to the behavior of micrometer-size particles. Several parameters have been used to characterize the reactivity of aluminum nanoparticles, including the fraction of aluminum that reacts prior to aluminum melting, heat of reaction, onset and peak temperatures, and maximum reaction rates. The results indicate that the reactivity of aluminum nanoparticles is significantly higher than that of the micrometer-size samples, but depending on the measure of reactivity, it may also depend strongly on the size distribution. The isoconversional method was used to calculate the apparent activation energy, and the values obtained for both the Al/O₂ and Al/MoO₃ reaction are in the range of 200-300 kJ/mol.     

添加表面活性剂两步沉淀法制备甲醇催化剂

采用添加表面活性剂两步沉淀法制备了具有高表面铜相对浓度的超细甲醇合成催化剂。以组成为H2/CO/CO2/N2=66/27/3/4(体积比）的原料气对催化剂进行了活性评价。结果表明，该催化剂比传统并流沉淀法制备的铜基催化剂活性提高47.9%，比两步沉淀法和添加表面活性剂并流沉淀法制备的铜基催化剂活性分别提高9.3%和16.8%。利用SEM、XRD及XPS方法对催化剂的结构、形貌和表面金属组成进行了表征。     

铝粉粒度对高氯酸铵热分解动力学的影响

采用热重-差示扫描量热(TG-DSC)联合技术研究了10.7 μm, 2.6 μm和40 nm铝粉对高氯酸铵(AP)热分解的影响. 结果表明, 铝粉的加入对AP的低温放热峰有抑制作用, 对高温放热分解反应有促进作用, 并且随铝含量的增加和铝粒径的减小这种作用更强烈. 采用多元非线性拟合技术对不同升温速率下TG-DSC实验数据进行拟合, 结果表明, 质量分数为40%的不同粒径铝粉的加入对AP的热分解三阶段(A→B→C→D)反应模型无影响, 但反应机理函数发生了改变. 纯AP, AP/Al(10.7 μm), AP/Al(2.6 μm)及AP/Al(40 nm)的反应机理函数组合分别为C1/D1/D1, C1/D1/D3, C1/D1/D4和C1/D1/F2.     

纳米金属粉对高氯酸铵热分解动力学的影响

The thermal decomposition characteristics of general ammonium perchlorate (g-AP) influenced by the addition of aluminum, nickel with different particle sizes (general and nano) are studied by TG and DSC. The results show that aluminum powders (both general and nano size) are nearly uninfluenced. Nano nickel powders have the greatest influence on the decomposition properties of g-AP among metal powders. Such accelerating effects of nanonickel powders are more apparent on the stage of high temperature decomposition than low temperature decomposition of g-AP and will be weakened with the decrease of the content of nanonickel. Nanonickel powders are also more effective than super fine nickel powders on accelerating the thermal decomposition of superfine AP (s-AP). The kinetic parameters of the thermal decomposition of s-AP and mixture of s-AP and nano nickel powders are obtained from the TG-DTG curves bythe integral method based on the Coats-Red fern equation. Nanonickel powders reduce the apparent activation energy of the thermal decomposition of s-AP from 157.9 kJ/mol to 134.9 kJ/mol. The most probable mechanism functions of the thermal decomposition reaction for s-AP and mixture of s-AP and nano nickel powders both belong to systems of Avrami-Erofeev equations. The mechanism of such accelerating effects has been discussed.     

Influence of dispersion aluminum powders on the regularities of their interaction with nitrogen

Regularities of the interaction of widely dispersed industrial powders and electroexplosive aluminum nanopowder with nitrogen under atmospheric pressure in a linearly rising temperature and isothermal conditions have been investigated. The effect of the powder’s dispersion and composition, and the structure of the oxide shell and metal core of the aluminum particles on the temperature range of reaction and its kinetic parameters is shown. The relationship between the process of dehydration of hydroxides that are part of the superficial oxide shell of Al particles and the initial temperature of interaction between the powders and nitrogen was investigated. It is shown that the staged nature of weight gain for powders in a nitrogen atmosphere that is observed under conditions of linear heating results from a change in the macrokinetic regime, due to the effect of the Al nitride layer.     

低密度薄水铝石晶体的水热生长过程

对Al2(SO4)3-CO(NH2)2-H2O体系在[Al3＋]=0.2 mol•L－1、[CO(NH2)2]:[Al3＋]=2∶1和反应2 h的水热条件下,不同反应温度的晶体生长过程进行了研究,得到呈多孔、针状团簇体状的微米级低密度薄水铝石晶体.采用ICP-AES、XRD、FT-IR、SEM、BET和粒径分布等手段对反应液和产物进行了分析和表征.结果表明,140 ℃时氢氧化铝凝胶或无定形粉体的析出已大部分完成,温度升高到180 ℃后,产物的结晶度变好,堆密度从117.2 kg•m－3相应增加到158.2 kg•m－3,比表面也从75.3 m2•g－1增加到88.3 m2•g－1,但平均粒径有所下降.晶体前驱体在550 ℃焙烧2 h后完全转化为形貌相似并且比表面增加的γ-Al2O3.     

Radiation-induced reduction of mixed copper and aluminum ionic aqueous solution

Colloidal Cu–Al nanoparticles were prepared in an aqueous polyvinyl alcohol solution containing copper chloride and aluminum chloride as precursors, isopropanol as a scavenger of hydroxyl radicals, and distilled water as a solvent. The gamma irradiations were carried out in a ⁶⁰Co gamma source chamber with different doses up to 120 kGy. The formation of Cu–Al nanoparticles has been observed initially by the change in color of the colloidal samples from colorless to brown. The nanoparticles properties were characterized by transmission electron microscopy, energy dispersive X-ray spectrometry, and UV–Vis spectrophotometer. At a constant Cu/Al molar ratio, size of the nanoparticles can be well controlled by varying the precursors concentration and radiation dose. The average particle diameter increases with increase of precursors concentration and decreases with increase of dose. This is owing to the competition between nucleation process, aggregation process, and ions association in the formation of nanoparticles during irradiation.     

Oxidation and melting of aluminum nanopowders

Recently, nanometer-sized aluminum powders became available commercially, and their use as potential additives to propellants, explosives, and pyrotechnics has attracted significant interest. It has been suggested that very low melting temperatures are expected for nanosized aluminum powders and that such low melting temperatures could accelerate oxidation and trigger ignition much earlier than for regular, micron-sized aluminum powders. The objective of this work was to investigate experimentally the melting and oxidation behavior of nanosized aluminum powders. Powder samples with three different nominal sizes of 44, 80, and 121 nm were provided by Nanotechnologies Inc. The particle size distributions were measured using small-angle X-ray scattering. Melting was studied by differential scanning calorimetry where the powders were heated from room temperature to 750 degrees C in an argon environment. Thermogravimetric analysis was used to measure the mass increase indicative of oxidation while the powders were heated in an oxygen-argon gas mixture. The measured melting curves were compared to those computed using the experimental particle size distributions and thermodynamic models describing the melting temperature and enthalpy as functions of the particle size. The melting behavior predicted by different models correlated with the experimental observations only qualitatively. Characteristic stepwise oxidation was observed for all studied nanopowders. The observed oxidation behavior was well interpreted considering the recently established kinetics of oxidation of micron-sized aluminum powders. No correlation was found between the melting and oxidation of aluminum nanopowders.     

Microstructure characteristics and shear properties of welding bonding of W/Al dissimilar metals with copper transitional layer

Commercial pure wrought tungsten and 1060 pure aluminum can be joined by using induction‐heat deposition (IHD) welding with commercial pure copper transitional layer. The microstructures of W/Cu/Al interfaces have been studied by means of scanning electron microscope, energy dispersive X‐ray, and X‐ray diffraction. Results show that copper as the transitional metal could form good interfaces with both tungsten and aluminum by IHD under proper processing parameters. The metallic bonding of W/Cu obtained by Cu and W mutual diffusing at a quite limited range without any intermetallic compounds, while eutectic of α(Al)/θ(CuAl₂) makes up Cu/Al interface. The average shear strength of W/Cu and Cu/Al interfaces are about 170 MPa and 55 Mpa, respectively, at room temperature. Copyright © 2012 John Wiley & Sons, Ltd.     

Investigation of catalytic activity of ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript> and ZnMn<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles in the thermal decomposition of ammonium perchlorate

A new powder metallurgy technique was developed in order to increase the reinforcement proportion of aluminum with two different fractions of Al₂O₃. Aluminum powders were mixed with 20 % vol of alumina particles as primarily reinforcement, and additional alumina was produced in situ as a result of reaction between Al and additional 7.5 % vol of Fe₂O₃ powder. The three grades of powders were milled and hot-pressed into small preforms, and differential scanning analysis (DSC) was performed to determine the kinetics of microstructural transformations produced on heating. DSC curves were mathematically processed to separate the superposing effects of thermal reactions. Transformation points on resulting theoretical curves evidenced two distinct exothermal reaction peaks close to the melting point of aluminum that were correlated with formation of Fe–Al compounds and oxidation of aluminum. Microstructural investigations by means of SEM-EDX and XRD suggested that these exothermal reactions produced complete decomposition of iron (III) oxide and formation of Fe–Al compounds during sintering at 700 °C, and therefore, heating at higher temperatures would not be necessary. These results, along with calculation of activation energies, based on Kissinger’s method, could be used to optimize the fabrication of Al-Al₂O₃ composites by means of reactive sintering at moderate temperatures.