L-半胱氨酸改性Fe3O4纳米粒子的水热合成及其应用

以L-半胱氨酸为表面改性剂与粒径调节剂,采用水热法制备具有良好分散稳定性的磁性Fe₃O₄纳米粒子。通过透射电镜（TEM）、扫描电镜（SEM）、X射线衍射仪（XRD）、比磁饱和强度测定仪（VSM）等对产物进行表征,研究L-半胱氨酸对磁性Fe₃O₄纳米粒子的形貌、粒径分布、晶型结构、分散稳定性等的影响,理论推导了L-半胱氨酸改性后的Fe₃O₄纳米粒子（L-Fe₃O₄纳米粒子）的生成机制,将该材料作为载体吸附金种后探讨其在催化对硝基苯酚方面的应用。结果表明：沉降22 h时,调节pH值为7.0制备的Fe₃O₄纳米粒子的沉降高度大约是L-Fe₃O₄纳米粒子的6.5倍;吸附金种后的L-Fe₃O₄纳米粒子催化效率大约是未改性Fe₃O₄纳米粒子的5倍。L-半胱氨酸有效的改善了Fe₃O₄纳米粒子与分散介质之间的相容性,保护并改善了纳米粒子的分散稳定性,在污水处理等方面有潜在的应用。     

磁光Fe3O4@SiO2@CdS复合材料的制备及表征

采用水解三氯化铁得到Fe₃O₄磁核,然后水解四乙氧基硅烷(TEOS)得到Fe₃O₄@SiO₂,再在其表面包覆半导体CdS即可得到良好的磁性光电信标Fe₃O₄@SiO₂@CdS。材料形貌、组成分析及光电化学测试表明成功地合成了具有超顺磁性的Fe₃O₄@SiO₂@CdS纳米复合材料。该材料分散均匀、具有良好的光学性能、在光电化学传感及光电催化等领域具有良好的应用前景。     

表面分子印迹磁性纳米粒子的制备及其血红蛋白传感应用

以Fe₃O₄磁性纳米粒子为载体、多巴胺（DA）为功能单体、血红蛋白（Hb）为模板分子,用氯铂酸氧化DA生成聚多巴胺（PDA）,同时氯铂酸还原为铂纳米粒子（PtNPs）,与Hb一起负载于Fe₃O₄纳米粒子表面,洗脱Hb后合成了表面分子印迹磁性纳米粒子（印迹Fe₃O₄/PDA-PtNPs）. 将印迹Fe₃O₄/PDA-PtNPs修饰于磁性玻碳基底表面,制得印迹Fe₃O₄/PDA-PtNPs修饰电极. 实验结果表明,印迹Fe₃O₄/PDA-PtNPs具有良好的水溶性,粒径分布均匀,生成的PtNPs具有良好的导电性和刚性. 用印迹Fe₃O₄/PDA-PtNPs构建的传感器对Hb具有良好的识别性,在0.14 ~ 2.7 μg·mL^-1 Hb浓度范围与交流阻抗变化值呈良好的线性关系,检出限（S/N=3）为0.05 μg·mL^-1.     

用于高效去除水中孔雀石绿的三层结构磁性复合材料Fe3O4@聚丙烯酸@ZiF-8的制备

设计并合成了一种以磁性纳米粒子为核,聚合物为中间层,金属有机骨架材料为外层的三层结构磁性复合材料(Fe₃O₄@PAA@ZIF-8)。首先利用溶剂热法制备Fe₃O₄纳米粒子,然后通过蒸馏沉淀聚合法在Fe₃O₄纳米粒子表面包覆聚丙烯酸(PAA)层,最后通过原位沉积法在PAA外部包覆ZIF-8。在对Fe₃O₄@PAA@ZIF-8的组成和结构进行表征的基础上,深入研究其对孔雀石绿(MG)的吸附性能。透射电子显微镜(TEM)显示Fe₃O₄@PAA@ZIF-8具有明显的三层结构,Fe₃O₄的平均粒径为117nm,PAA层厚度约为17 nm,ZIF-8层的厚度约为14 nm。Fe₃O₄@PAA@ZIF-8对MG的吸附量随着p H的升高而增大,吸附过程符合准二阶动力学模型和Langmuir等温吸附模...     

超顺磁性Fe3O4纳米粒子在磁共振造影中的应用

超顺磁性Fe₃O₄纳米粒子由于其廉价、低毒及超顺磁等特性,已成为重要的一类磁共振造影剂.本文综述了超顺磁性Fe₃O₄纳米粒子的可控制备方法,归纳总结影响粒径、结晶度和磁性能的主要因素和影响规律;为进一步提高磁性能并实现多功能,总结了Fe₃O₄纳米粒子进一步组装和表面改性的方法和机理;系统讨论了Fe₃O₄纳米粒子的形貌、尺寸和表面性能等对磁性能和生物相容性的影响规律;并指出了Fe₃O₄纳米粒子在磁共振造影领域潜在的发展方向和研究热点.     

用于磁性靶向治疗肺纤维化的聚多巴胺包覆的Fe3O4/甲强龙/环磷酰胺复合超粒子

肺纤维化是一种致命性肺部疾病, 目前临床常规的甲强龙(MPS)联合环磷酰胺(CTX)治疗方法存在明显的不良反应. 基于降低药物毒副作用的目的, 本文设计了一种聚多巴胺(PDA)包覆的Fe₃O₄纳米粒子/甲强龙/环磷酰胺复合超粒子(Fe₃O₄/MPS/CTX@PDA SPs), 提出磁性靶向治疗肺纤维化的思路. 从预制的油溶性Fe₃O₄纳米粒子出发, 通过水包油微乳液模板法制备了Fe₃O₄ 超粒子(SPs), 并在进一步包覆PDA壳层的过程中引入MPS和CTX, 制备了Fe₃O₄/MPS/CTX@PDA SPs, 考察了Fe₃O₄/MPS/CTX@PDA SPs的稳定性、 磁性、 对MPS和CTX的负载及释放, 分析了其生物毒性, 并建立动物模型验证了其磁性靶向功能.     

磁性荧光双功能复合纳米粒子Fe3O4@SiO2@ZrO2:Tb3+的合成和表征

通过原位反应合成法成功合成了一种新型水溶性的磁性荧光复合纳米粒子Fe₃O₄@SiO₂@ZrO₂:Tb³⁺,并通过扫描电子显微镜(SEM)、X射线粉末衍射仪(XRD)、红外光谱仪(FT-IR)、磁性测试仪和荧光(PL)光谱对其形貌、尺寸、相组成、磁性和荧光性能进行了表征。 结果表明,核(Fe₃O₄@SiO₂)壳(ZrO₂:Tb³⁺)结构组成的磁性荧光复合纳米粒子具有超顺磁性,其饱和磁化强度达到36 emu/g,并且在494 nm(⁵D₄→⁷F₆)、549 nm(⁵D₄→⁷F₅)、587 nm(⁵D₄→⁷F₄)和625 nm(⁵D₄→⁷F₃)处具有4个Tb³⁺特有的荧光发射光谱带峰值。 磁性荧光双功能的复合纳米粒子在生物医学领域具有潜在的应用价值。     

超顺磁性Fe3O4/Au@Ag复合材料的合成及其SERS性能研究

利用溶剂热法和种子生长法分别合成Fe₃O₄磁性纳米粒子和Au@Ag核壳纳米粒子, 利用静电吸附方法成功将聚乙酰亚胺(PEI)修饰到Fe₃O₄表面并通过N-Ag共价键将Au@Ag核壳纳米粒子组装到Fe₃O₄表面, 制备Fe₃O₄/Au@Ag复合材料. 通过控制Au@Ag复合粒子的加入量, 来调节Fe₃O₄/Au@Ag复合材料的表面增强拉曼(SERS)活性. 以对巯基苯胺(p-ATP)为拉曼活性探针分子来考察该复合纳米材料的SERS性能, 检测限可以低至2×10^-9 mol/L. 同时, 将该复合材料应用于农药分子福美双的检测, 检测限可以低至10^-6 mol/L. 这种功能性复合材料既具有良好的SERS活性, 又具有Fe₃O₄磁性内核, 可以通过外加磁场实现对待测分子的分离、富集, 具有更广泛的应用前景.     

羧甲基纤维素/Fe3O4复合纳米磁性材料的制备、表征及吸附性能的研究

采用改进的氧化沉淀法在羧甲基纤维素(CMC)体系中制备了以磁性纳米Fe₃O₄为核心, 外层包覆羧甲基纤维素的复合磁性纳米材料. 用透射电镜、X射线衍射、红外光谱、Zeta电位和震动样品磁强计对复合纳米Fe₃O₄进行了表面形貌、结构和磁学的表征. 在此基础上研究了复合纳米Fe₃O₄对Cu^2＋的吸附性能, 探讨了溶液pH、反应时间和 Cu^2＋的初始浓度对其吸附性能的影响. 实验结果表明, 复合Fe₃O₄粒子为反尖晶石型, 平均粒径在40 nm左右, 羧甲基纤维素在Fe₃O₄粒子表面是化学吸附, 复合Fe₃O₄粒子的饱和磁化强度为36.74 emu/g, 在中性溶液中Cu^2＋的吸附量最高, 吸附平衡时间为1.5 h, 二级动力学模型能够很好地拟合吸附动力学数据, 吸附等温数据符合Langmuir模型. 复合纳米Fe₃O₄对Cu^2＋的吸附机理主要为表面配位反应.     

四氧化三铁/单壁碳纳米管磁性复合纳米粒子分散固相微萃取-高效液相色谱法测定牛奶中的香精添加剂

通过化学键合的方法制备单壁碳纳米管包覆的四氧化三铁（Fe₃O₄/CNTs）磁性复合纳米粒子。首先用水热法合成磁性Fe₃O₄纳米粒子,并进行硅烷氨基化处理,羧基化的单壁碳纳米管通过1-（3-二甲基氨基丙基）-3-乙基碳二亚胺（EDC）和N-羟基琥珀酰亚胺（NHS）交联剂反应修饰到Fe₃O₄纳米颗粒表面。合成的Fe₃O₄/CNTs复合纳米粒子具有很高的磁响应度和很好的分散能力,是一种很好的分散固相萃取剂。本研究将合成的Fe₃O₄/CNTs纳米粒子用于分散固相微萃取富集牛奶中的香精添加剂,并与高效液相色谱分析联用,实现了香兰素和乙基香兰素的快速高效富集和高灵敏度检测,两者的检出限达10 μg/L,回收率大于92%。本研究表明,合成的Fe₃O₄/CNTs磁性复合粒子是一种很好的奶制品中香兰素添加剂的样品前处理富集材料。     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

NaBO2-NaCl-Na2CO3, NaBO2- Na2CO3-NaMoO4, NaBO2- Na2CO3-NaWO4, and NaBO2-NaCl-Na2WO4 ternary systems

The phase diagrams of the NaBO₂-NaCl-Na₂CO₃, NaBO₂-Na₂CO₃-Na₂MoO₄, NaBO₂- Na₂CO₃-Na₂WO₄, and NaBO₂-NaCl-Na₂WO₄ ternary systems were studied by a calculation-experimental method and differential thermal analysis. The coordinates of ternary eutectics were determined: E ₁: 612°C, 16 mol % NaBO₂, 42 mol % NaCl, and 42 mol % Na₂CO₃; E ₂: 568°C, 12 mol % NaBO₂, 28 mol % Na₂CO₃, and 60 mol % Na₂MoO₄; E ₃: 575°C, 12 mol % NaBO₂, 32 mol % Na₂CO₃, and 56 mol % Na₂WO₄; E ₄: 628°C, 8 mol % NaBO₂, 20 mol % NaCl, and 72 mol % Na₂WO₄; and E ₅: 655°C, 9 mol % NaBO₂, 53 mol % NaCl, and 38 mol % Na₂WO₄.     

Structural chemistry of Sr3Cr2WO9, Ca3Cr2WO9, and Ba3Cr2WO9

We have studied the preparation and crystallographic structure of three perovskite-type compounds: Sr₃Cr₂WO₉, cubic, the lattice parameter of which is a = 7.812Å; Ca₃Cr₂WO₉, tetragonal, the lattice parameters of which are a = 5.408 Å and c = 7.635Å; and Ba₃Cr₂WO₉, hexagonal, the lattice parameters of which are a = 5.691 Å and c = 13.957Å. We have compared these three structures and shown the relationship between the dimensions of the alkaline-earth metal and the existence of the different structures.     

Theoretical study of polyoxide clusters B20O30, Al20O30, V20O50, Si20O30H20, and Si20O30F20

The structural, electronic, and vibrational characteristics and energies of the isolated polyoxide clusters B₂₀O₃₀, Al₂₀O₃₀, V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀ and their complexes with the H⁻ ion and ammonia complexes Al₂₀O₃₀ · nNH₃ have been calculated by the density functional theory B3LYP method with different basis sets. The computation results show that the symmetric closo structure I _h with oxygen bridges located above the centers of the faces of an empty [M₂₀] dodecahedron is more favorable for V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀. For B₂₀O₃₀, the cage closo isomer is also more favorable than the other isomers, but its structure is severely distorted as compared to a dodecahedron and has a symmetry close to C ₃ . For Al₂₀O₃₀, the I _h structure corresponds to a high-lying local minimum of the potential energy surface. For Al₂₀O₃₀, a set of unusual puckshaped isomers of symmetry C _i , with different numbers of four-coordinate atoms ^IVAl and three-coordinate atoms ^IIIO, was localized; these structures are more than 90 kcal/mol more favorable than the dodecahedron I _h . The most favorable isomer of Al₂₀O₃₀ contains twelve four-coordinate atoms ^IVAl and four five-coordinate atoms ^VAl. The energies of dissociation of the most favorable M₂₀O₃₀ clusters into the M₂O₃ (C _2v ) and M₄O₆ (T _d ) fragments and, in the case of Al₂₀O₃₀, also into the Al₈O₁₂ (O _h ) and Al₁₂O₁₈ (D _3d ) fragments, have been estimated. The conclusion has been drawn that these clusters can, in principle, exist and can be experimentally detected in the isolated state. Analogous calculations have been performed for ammonia complexes Al₂₀O₃₀ · nNH₃ with n varying from 1 to 20. The effect of solvation on the relative stability of the dodecahedral and puckshaped isomers of the Al₂₀O₃₀ cluster is observed. The isomers with ammonia molecules in their first coordination sphere become much closer to one another on the energy scale; however, the dodecahedron remains a considerably less favorable intermediate. Original Russian Text ? O.P. Charkin, N.M. Klimenko, D.O. Charkin, 2008, published in Zhurnal Neorganicheskoi Khimii, 2008, Vol. 53, No. 4, pp. 624–635.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.