新型有序介孔磺酸化酚醛树脂FDU-16-SO3H的合成与酸催化性能

通过氯磺酸磺化有序介孔酚醛树脂(FDU-16)制备了新型有序介孔固体酸催化剂FDU-16-SO₃H. X射线衍射(XRD)、氮气吸附以及透射电镜(TEM)等表征结果表明, 经过磺化后的固体酸催化剂依然保持了高度有序性, 大量的磺酸根基团存在于材料的骨架之中. 在酯化反应和酰基化反应中, 这种新型有序介孔固体酸催化剂表现出比工业树脂和磺酸化介孔二氧化硅等材料更高的催化活性, 这主要归因于它具有较大的比表面积、较强的酸性以及骨架的疏水性.     

不同载体负载的铂催化剂在丙酮酸乙酯不对称氢化反应中的活性及其铂流失率比较

以介孔树脂材料FDU-14和介孔碳材料CMK-3为载体制备了两种负载型铂催化剂, 用N₂气吸附、X射线衍射及CO化学吸附等手段对这两种催化剂进行了表征, 并将这两种不同的负载型铂催化剂在丙酮酸乙酯不对称氢化反应中的催化性能及其铂流失率与商品化Pt/Al₂O₃催化剂进行了比较. 研究结果表明, 尽管Pt/Al₂O₃催化剂的初始活性和光学选择性均较高, 然而相同反应条件下乙酸溶剂中Pt/FDU-14和Pt/CMK-3催化剂的铂流失率比Pt/Al₂O₃催化剂的低. 通过对催化剂进行CO吸附原位傅里叶变换红外漫反射光谱(DRIFTS)表征, 从载体的不同表面电子性质角度解释了不同载体负载的铂催化剂在丙酮酸乙酯不对称氢化反应中的活性和铂流失率的差异.     

手性修饰的介孔树脂材料负载铂催化剂上丙酮酸乙酯的不对称氢化反应

采用氯铂酸和二氯四氨合铂为前体通过浸渍法分别制备了介孔树脂材料FDU-14负载的质量分数为5%的铂催化剂Pt/FDU-14, 并利用XRD, TEM, N₂气吸附和CO化学吸附等手段对催化剂进行了表征. 考察了经过手性分子辛可尼定修饰后的Pt/FDU-14催化剂在丙酮酸乙酯不对称氢化反应中的催化性能. 以氯铂酸为前体制备的Pt/FDU-14催化剂因其具有较小的铂粒子和较高的分散度而表现出较高的活性, 乙酸溶剂中的初始活性(TOF)可以达到21902 mol/(mol?h); 而以二氯四氨合铂为前体制备的Pt/FDU-14催化剂则具有较强的手性诱导能力, 乙酸溶剂中(R)-(+)-乳酸乙酯的光学选择性可以达到81.4% e.e.. 更重要的是, 由于FDU-14具有较强的疏水性, Pt/FDU-14催化剂在水溶剂中也表现出较高的催化性能, 并且还可以重复使用10次以上.     

介孔氧化铝复合材料负载铂催化剂上丙酮酸乙酯的不对称氢化反应

采用固相研磨法制备了有序介孔树脂FDU-14孔道限阈分散的Al2O3复合材料Al2O3@FDU-14.以其为载体,采用浸渍法制备了4.0％ Pt/Al2O3@FDU- 14催化剂,并利用X射线衍射、透射电子显微镜和N2吸附等手段对催化剂进行了表征.结果表明,Pt/Al2O3@FDU- 14催化剂保持了FDU-14的介孔...     

SBA-15负载Pd催化剂的制备及其在Heck反应中的应用研究

利用水热反应制备了表面离子液体功能化的SBA-15介孔材料,在丙酮溶液中与氯化钯反应,然后使用水合肼在乙醇中还原.测试了这种催化剂在Mizoroki-Heck反应中的催化活性.与直接负载在SBA-15上的钯催化剂相比,这种表面修饰的介孔SBA-15负载催化剂表现出更高的催化活性、可回收性和反应稳定性.氮气吸脱附实验和小角XRD衍射实验表明,在合成中,材料的介孔性能并没有被破坏.透视电镜也表征了该材料的表面形貌.最后,Mizoroki-Heck反应表明该催化剂具有很高的催化活性,且循环五次后,其催化活性降低并不明显.     

离子液体接枝的有机介孔催化剂的制备及催化碳酸丙烯酯水解反应

以甲基咪唑和3-氯-1丙醇为原料合成离子液体（1-羟丙基-3-甲基咪唑四氟硼酸盐,NpmimBF4）,并将其接枝固载到有机介孔材料（FDU-15）上,合成制备了有机介孔催化剂（NpmimBF4- FDU）。采用热重、Ｘ射线衍射、红外光谱及透射电子显微镜等技术手段对催化剂结构进行了表征,并考察了催化剂在碳酸丙烯酯（PC）水解反应中的催化性能,结果表明,该催化体系在常压下能有效催化碳酸丙烯酯水解生成1,2-丙二醇。在催化剂的质量分数为4%、温度80 ℃、反应时间2 h的条件下,1,2-丙二醇的产率大于99%。经简单分离后催化剂可重复使用5次,但活性变化较大。同时对催化碳酸丙烯酯水解生成1,2-丙二醇（PG）的反应机理进行了初步探讨。     

负载于孔道内部的手性酸碱催化不对称Aldol反应

将手性的伯胺-叔胺与B酸组成的酸碱对负载到介孔材料SBA-15孔道的内表面,得到了一种非均相双功能催化剂.该催化剂在催化丙酮和不同醛的aldol反应时得到了中等的活性和对映体选择性,重复使用6次后活性没有明显下降.与以硅胶为载体的催化剂相比,以介孔SBA-15分子筛为载体的催化剂ee值更高,这可能是由于介孔孔道限制效应引起的.     

铑-三苯基膦配合物功能化的聚合物@介孔氧化硅复合材料在1-辛烯氢甲酰化反应中的应用(英文)

通过在介孔氧化硅材料中原位聚合的方法制备了三苯基膦功能化的有机聚合物@介孔氧化硅复合材料PPh3polymer@FDU-12.采用X射线衍射、氮气吸附脱附、透射电镜和热重等手段对其结构和组成进行了表征.该复合材料与金属前驱体Rh(acac)(CO)2配位后得到的固体催化剂,在长链烯烃1-辛烯的氢甲酰化反应中,醛选择性可达92%–96%,并表现出高于聚合物的活性(99%转化率).这主要归因于介孔氧化硅材料的高比表面积和有序的孔结构更有利于反应物和催化活性中心的接触.研究发现,调变复合材料中聚合物的含量或使用不同孔道结构的氧化硅载体(SBA-15,MCM-41和FDU-12)都会影响固体催化剂的反应活性和选择性.该方法得到的多相催化剂具有较好的循环使用性能,在循环使用15次后仍能保持较好的反应活性,但醛选择性有所降低.     

SBA-15 固载离子液体功能化脯氨酸的制备及其催化 Knoevenagel 缩合反应

 以 L-脯氨酸为原料合成了离子液体功能化脯氨酸前驱体 (IL-Pro), 并将其固载到 SBA-15 介孔分子筛上, 制得 IL-Pro/SBA-15 催化剂. 用红外光谱、热重、N2 吸附-脱附、X 射线衍射和透射电镜等手段表征了 IL-Pro/SBA-15 催化剂, 并考察了该催化剂在 Knoevenagel 缩合反应中的催化性能. 结果表明, 固载离子液体功能化脯氨酸没有破坏 SBA-15 的有序介孔结构, 但孔体积、孔径和比面表积有所下降; IL-Pro/SBA-15 的失重峰在 250~360 oC (峰值为 310 oC). 在以苯甲醛和丙二腈为底物的 Knoevenagel 反应中, IL-Pro/SBA-15 催化剂表现出较高的活性, 缩合产物收率高达 94%; 经简单分离后催化剂可重复使用 7 次以上而活性基本保持不变.     

SBA-15固载脯氨酸催化剂的制备及其在不对称Mannich反应中的应用

以4-羟基-L-脯氨酸为原料合成了脯氨酸衍生物,并将其固载于介孔SBA-15分子筛上制备了Pro/SBA-15催化剂.用X射线衍射、N2吸附-脱附、扫描电镜和红外光谱等手段对Pro/SBA-15催化剂进行了表征,并考察了催化剂在不对称Mannich反应中的催化性能.结果表明,固载脯氨酸不影响SBA-15的有序介孔结构,只是其孔径、孔体积和BET比表面积有所减小,在不对称Mannich反应中具有较高的催化活性和对映选择性.与均相催化相比,以对硝基苯甲醛为反应物时可得到较高的分离收率(80%)和中等的对映选择性(ee=60%).催化剂通过简单分离后可重复使用4次以上,其催化性能基本保持不变.     

Immobilization of palladium in mesoporous silica matrix: preparation, characterization, and its catalytic efficacy in carbon-carbon coupling reactions

Palladium(0) has been immobilized into the silica-based mesoporous material to develop catalyst Pd(0)-MCM-41, which is found to be highly active in carbon-carbon coupling reactions. [Pd(NH3)4]2+ ions have been incorporated into the mesoporous material during synthesis of MCM-41 and subsequently upon treatments with hydrazine hydrate Pd2+ ions present in mesoporous silica matrix were reduced to Pd(0) almost instantaneously. The catalyst has been characterized by small-angle X-ray diffraction, N2 sorption, and transmission electron microscopy (TEM). TEM and surface area measurements clearly demonstrate that the immobilization of Pd(0) into the mesoporous silica has a significant effect on pore structure of the catalyst. Nevertheless, after immobilization of palladium the meso-porosity of the material is retained, as evidenced in the nitrogen sorption measurement. The TEM micrograph shows that both MCM-41 and Pd(0)-MCM-41 have similar types of external surface morphology; however, Pd(0)-MCM-41 was less ordered. Pd(0)-MCM-41 showed high catalytic activity toward carbon-carbon bond formation reactions like Heck and Sonogashira coupling, as evidenced in high turn-over numbers. In contrast to many other Pd-based catalysts reported so far, Pd(0)-MCM-41 acts as a truly heterogeneous catalyst in C-C coupling reactions. Notably, the new heterogeneous catalyst is found to be efficient in the activation of arylchloride to give impressive conversion in cross coupling (15-45% for Heck and 30% for Sonogashira) reactions under mild conditions.     

The heterogeneous catalytic heck reaction in an ionic liquid

The C-C cross coupling reaction between bromobenzene and styrene in the presence of Pd deposited on mesoporous acetylene soot (Pd/C) occurred in a tetraalkylammonium ionic liquid (IL) as a truly heterogeneous catalytic process. The active palladium form was not transferred into the reaction solution. Deposited palladium activation was observed when the Pd/C catalyst was preliminarily heated in the IL in the presence of dibutylamine as a base.     

巯基功能化介孔材料高效锚定钯负载型催化剂的制备及其苯酚加氢催化性能

以含巯基官能团有机硅烷修饰的介孔材料MCM-41和SBA-15为载体, 采用浸渍-氢气还原法制备了高分散和高活性的负载型Pd催化剂. X射线衍射、N₂吸附-脱附和透射电子显微镜表征结果显示, 所制Pd催化剂Pd-SH-MCM-41和Pd-SH-SBA-15具有很好的长程有序结构、分布均匀的孔径、高比表面积及高度分散的Pd颗粒. 苯酚加氢反应结果表明, 以Pd-SH-MCM-41和Pd-SH-SBA-15为催化剂时, 在80℃, 1.0MPa反应1h, 苯酚转化率达99%以上, 环己酮选择性为98%. 它们的催化活性为商业Pd/C催化剂的5倍, Pd/MCM-41和Pd/SBA-15催化剂的3倍. 这可归因于介孔材料表面修饰的巯基官能团对Pd的锚定作用, 避免了Pd颗粒的团聚, 使其高度分散在介孔材料上.     

Pd immobilized on polyamide based on melamine and terephalic acid as an efficient and recyclable catalyst for Suzuki‐Miyaura coupling reaction

A simple synthetic strategy of polyamide was described from melamine and terephalic acid via one‐step polycondensation. PdCl₂ was then immobilized on the polyamide (denoted as Pd/MPA). Melamine and terephalic acid not only acted as monomers but also provided the ligand sites to help the polyamide to coordinate with Pd(II). The Pd/MPA catalyst was characterized by FT‐IR, TGA, SEM, TEM, XPS, N₂ adsorption‐desorption and atomic absorption spectroscopy. The catalyst was used in Suzuki‐Miyaura coupling reaction of various aryl halides, including less reactive chlorobenzene and benzyl chloride, to give the coupling products in moderate to excellent yields. High turnover frequencies (TOF) up to 29400 h^‐1 can be also obtained. In addition, it behaved truly as a heterogeneous catalyst with high reusability after being recycled 6 times and palladium leaching was negligible during the process. This work provides a practical polyamide support to develop heterogeneous palladium catalysts with simple synthetic procedure and low cost.     

Palladium‐anchored multidentate SBA‐15/di‐urea nanoreactor: A highly active catalyst for Suzuki coupling reaction

Modification of mesoporous silica was carried out by reaction of SBA‐15 with di‐urea‐based ligand. Next, with the help of this ligand, palladium ions were anchored within the multidentate SBA‐15/di‐urea pore channels with high dispersion. The SBA‐15/di‐urea/Pd catalyst was characterized using various techniques. Theoretical calculations indicated that each palladium ion was strongly interacted with one nitrogen and two oxygen atoms from the multidentate di‐urea ligand located in SBA‐15 channels and these interactions remained during the catalytic cycle. These results are in good agreement with those of hot filtration test: the palladium ions have very high stability against leaching from the SBA‐15/di‐urea support. The catalytic performance of SBA‐15/di‐urea/Pd nanostructure was examined for the Suzuki coupling reaction of phenylboronic acid and electronically diverse aryl halides under mild conditions with a minimal amount of Pd (0.26 mol%). Compared to previous reports, this protocol afforded some advantages such as short reaction times, high yields of products, catalyst stability without leaching, easy catalyst recovery and preservation of catalytic activity for at least six successive runs.     

Palladium based heterogeneous catalyst by evaporation-induced self-assembly: use of biopolymer as a surface functionalizing and reducing agent

Palladium-based composites are widely used as a heterogeneous catalyst in carbon–carbon coupling reactions and in catalytic converters used in the car industry. In this work, we demonstrate a simple, green and scalable synthesis procedure to obtain palladium (Pd) based heterogeneous catalyst. Surface functionalized silica microparticles were obtained in one-step by spray-drying a colloidal suspension of silica nanoparticles and gum arabic, an environmental-friendly biopolymer. Subsequently, palladium nanoparticles were reduced and attached to the substrate by gum arabic. The as-synthesized composite was characterized by field-emission scanning electron microscopy (FESEM), energy-dispersive x-ray spectroscopy (EDS), x-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), small angle x-ray scattering (SAXS), and high-resolution transmission electron microscopy (HR-TEM). The Pd@SiO₂ composite was used as a catalyst in the reduction reaction of 4-nitrophenol by sodium borohydride. The catalyst showed good recycling properties. The present environmental-friendly approach for fabrication of Pd-based heterogeneous catalyst circumvents various complex chemical steps involved in conventional chemical methods and could be generalized for the production of ceramic or magnetite-based Pd composites.     

有序介孔胺化的聚合物材料的合成及在Knoevenagel缩合反应中的催化性能

通过氯化和胺化等手段对有序介孔聚合物材料(FDU-16)进行功能化, 成功地将胺基引入到介孔聚合物骨架中, 制备出新型有序介孔固体碱催化材料. X射线衍射(XRD)、 氮气吸附-脱附及透射电子显微镜(TEM)表征结果表明, 功能化后的固体碱材料依然保持高度有序性; 红外表征结果表明, 大量的胺基被引入到材料的骨架中. 在Knoevenagel缩合中, 这种新型有序介孔固体碱材料表现出比功能化的介孔二氧化硅等材料更高的催化活性, 这主要归因于其具有较高的比表面积、较强的碱性以及较多的活性中心.     

Application of Highly Efficient,Recyclable Organic–Inorganic Hybrid Material Immobilized Palladium Catalyst in Amine‐ and Phosphine‐Free Suzuki–Miyaura Reaction

Palladium immobilized on organic–inorganic (silica‐gel) hybrid materials behaves as a very efficient heterogeneous catalyst in the Suzuki–Miyaura coupling reaction. Aryl iodides, bromides, and activated chlorides, coupled with organoboronic acids (Suzuki–Miyaura reaction), smoothly afford the corresponding cross‐coupling products in excellent yields under phosphine‐free and amine‐free reaction conditions in the presence of 3‐aminopropyl functionalized silica‐gel immobilized palladium (silica‐APTS‐Pd) as catalyst. Furthermore, the silica‐supported palladium catalyst could be recovered and recycled by simple filtration of the reaction solution. It could be reused for more than 15 consecutive trials without significant loss of its catalytic activity.