DNA biosensor based on the electrochemiluminescence of Ru(bpy)3(2+) with DNA-binding intercalators

This paper reports a novel detection method for DNA hybridization based on the electrochemiluminescence (ECL) of Ru(bpy)(3)(2+) with a DNA-binding intercalator as a reductant of Ru(bpy)(3)(3+). Some ECL-inducible intercalators have been screened in this study using electrochemical methods combined with a chemiluminescent technique. The double-stranded DNA intercalated by doxorubicin, daunorubicin, or 4',6-diamidino-2-phenylindole (DAPI) shows a good ECL with Ru(bpy)(3)(2+) at +1.19 V (versus Ag/AgCl), while the non-intercalated single-stranded DNA does not. In order to stabilize the self-assembled DNA molecules during ECL reaction, we constructed the ECL DNA biosensor separating the ECL working electrode with an immobilized DNA probe. A gold electrode array on a plastic plate was assembled with a thru-hole array where oligonucleotide probes were immobilized in the side wall of thru-hole array. The fabricated ECL DNA biosensor was used to detect several pathogens using ECL technique. A good specificity of single point mutations for hepatitis disease was obtained by using the DAPI-intercalated Ru(bpy)(3)(2+) ECL.     

A solid-state electrochemiluminescence sensing platform for detection of adenosine based on ferrocene-labeled structure-switching signaling aptamer

A solid-state electrochemiluminescence sensing platform based on ferrocene-labeled structure-switching signaling aptamer (Fc-aptamer) for highly sensitive detection of small molecules is developed successfully using adenosine as a model analyte. Such special sensing platform included two main parts, an electrochemiluminescence (ECL) substrate and an ECL intensity switch. The ECL substrate was made by modifying the complex of Au nanoparticle and Ruthenium (II) tris-(bipyridine) (Ru(bpy)₃²⁺-AuNPs) onto Au electrode. An anti-adenosine aptamer labeled by ferrocene acted as the ECL intensity switch. A short complementary ssDNA for the aptamer was applied to hybridizing with the aptamer, yielding a double-stranded complex of the aptamer and the ssDNA on the electrode surface. The introduction of adenosine triggered structure switching of the aptamer. As a result, the ssDNA was forced to dissociate from the sensing platform. Such structural change of the aptamer resulted in an obvious ECL intensity decrease due to the increased quenching effect of Fc to the ECL substrate. The analytic results were sensitive and specific.     

基于MCM-41负载联吡啶钌的电致化学发光传感器

利用静电吸附作用将联吡啶钌[Ru(bpy)₃²⁺]负载到巯基化MCM-41介孔二氧化硅纳米颗粒上, 通过金-巯键修饰法将负载后的MCM-41固定在金电极表面, 发展了一种基于MCM-41负载联吡啶钌的电致化学发光传感器, 并研究了其电化学及电致化学发光行为. 基于三聚氰胺与增敏剂三正丙胺氨基结构的相似性, 将负载Ru(bpy)₃²⁺的MCM-41电致化学发光传感器用于三聚氰胺的检测, 获得了良好的检测效果, 为检测三聚氰胺提供了一种快速、简便的方法. 同时, 该研究为Ru(bpy)₃²⁺在电极表面的固定化提供了新思路.     

Novel cathodic electrochemiluminescence of tris(bipyridine) ruthenium(II) on a gold electrode in acidic solution

The novel phenomenon of cathodic electrochemiluminescence on a gold electrode in tris(bipyridine) ruthenium(II) (Ru(bpy)(3)(2+)) solution is described for the first time. A cathodic electrochemiluminescence (ECL) was found to mainly occur at 0.4-0.8 V with continuous potential scanning from 0.2-1.4 V and the ECL peak was observed around 0.68 V, which was quite different from generally reported Ru(bpy)(3)(2+) ECL. Our group speculated that Ru(bpy)(3)(2+) possibly reacts with the gold electrode in the acidic phosphate buffer solution (PBS) to generate luminescence. The possible ECL mechanism was discussed according to the presented results. Moreover, it is revealed that the Au as co-reactant in the Ru-system contributed dominantly to the whole ECL. Therefore, the reaction between Ru(bpy)(3)(2+) and the newly formed Au implied that the inert metal Au could become a promising material for ECL investigations.     

[Ru(bpy)2(dcbpy)NHS] Labeling/Aptamer‐Based Biosensor for the Detection of Lysozyme by Increasing Sensitivity with Gold Nanoparticle Amplification

A novel [Ru(bpy)₂(dcbpy)NHS] labeling/aptamer‐based biosensor combined with gold nanoparticle amplification for the determination of lysozyme with an electrochemiluminescence (ECL) method is presented. In this work, an aptamer, an ECL probe, gold nanoparticle amplification, and competition assay are the main protocols employed in ECL detection. With all the protocols used, an original biosensor coupled with an aptamer and [Ru(bpy)₂(dcbpy)NHS] has been prepared. Its high selectivity and sensitivity are the main advantages over other traditional [Ru(bpy)₃]²⁺ biosensors. The electrochemical impedance spectroscopy (EIS) and atomic force microscopy (AFM) characterization illustrate that this biosensor is fabricated successfully. Finally, the biosensor was applied to a displacement assay in different concentrations of lysozyme solution, and an ultrasensitive ECL signal was obtained. The ECL intensity decreased proportionally to the lysozyme concentration over the range 1.0×10^?13–1.0×10^?8 mol L^?1 with a detection limit of 1.0×10^?13 mol L^?1. This strategy for the aptasensor opens a rapid, selective, and sensitive route for the detection of lysozyme and potentially other proteins.     

Detection of thrombin using electrogenerated chemiluminescence based on Ru(bpy)3(2+)-doped silica nanoparticle aptasensor via target protein-induced strand displacement

A sensitive and selective aptasensor using tri(2,2′-bipyridyl)ruthenium(II)-doped silica nanoparticles (Ru(bpy)₃²⁺-doped SNPs) as DNA tags for detection of thrombin is developed based on the target protein-induced strand displacement of the DNA probe. For the proposed aptasensor, the aptamer was assembled on the surface of the Au electrode through Au-S binding. The hybridization event between the DNA probe labeled by the Ru(bpy)₃²⁺-doped SNPs and the aptamer was evaluated by electrogenerated chemiluminescence (ECL) measurements. Then, the DNA probe was displaced by thrombin and the binding event between the thrombin and the aptamer was monitored by ECL measurements again. The difference of ECL intensity (ΔI_ECL) of the two events could be used to quantify the thrombin. Other proteins, such as bovine serum albumin and bovine hemoglobin, had almost negligible ΔI_ECL. Under the optimal conditions, the ΔI_ECL was linearly related to the concentration of the thrombin in the range of 10 fM to 10 pM and the detection limit was down to 1.0 fM since SNPs containing a large number of Ru(bpy)₃²⁺ molecules were labeled on the DNA probe.     

Determination of Amino Acids by Ru(bpy)_3~(2+) Cathodic Electrochemiluminescence with High Sensitivity

The unique cathodic electrochemiluminescence(ECL) emission of Ru(bpy)32+(bpy=2,2′-bipyridine) was observed via Nafion film at Au electrode[Au/Nafion/Ru(bpy)32+] at about 0.20 V(vs. Ag/AgCl) and applied to the determination of several amino acids without prior derivatization with high sensitivity. The cathodic electrochemilumi-nescence(ECL) exhibits the detection limits and linear ranges of several amino acids comparable to or better than those of capillary electrophoresis with conventional ECL detection method(at 1.10—1.20 V vs. Ag/AgCl) based on precolumn derivatization. The results suggest that the cathodic ECL is promising for the detection of amino acids in bioanalysis.     

十二烷基苯磺酸钠-盐酸苯海索-Ru(bpy)2+3体系的电化学发光行为研究及应用

在十二烷基苯磺酸钠(SDBS)存在下,考察了盐酸苯海索(BH)-Ru(bpy)32+体系的电化学及其发光行为。结果表明,BH对Ru(bpy)32+体系的电化学发光具有增敏效应;在SDBS存在下,BH对Ru(bpy)32+体系电化学发光的增敏效应显著增强,发光强度提高约16倍。据此建立了一种高效、简便的BH电化学发光新方法。在最佳实验条件下,BH的浓度在4.0×10-7～1.0×10-4 mol/L范围内与相对发光强度呈线性关系(r=0.995 5),检出限(S/N=3)为1.11×10-9 mol/L;连续平行测定1.0×10-5 mol/L BH溶液10次,发光强度的RSD为3.2%。样品的回收率为96%～108%,RSD为4.3%。该方法样品前处理简单,具有较高的选择性和灵敏度,用于实际样品中BH的测定,结果满意。     

基于Ru(bpy)■-三乙胺体系的电致化学发光生物传感器检测葡萄糖

联吡啶钌(Ru(bpy)■)拥有优良的电致化学发光(ECL)性能,但其较好的水溶性使其固载面临巨大问题。该文制备了Pt纳米粒子与Ru(bpy)■的复合物(Pt NPs-Ru),将其修饰于电极并进一步固载葡萄糖氧化酶(GOx)制得传感器。基于H2O2对Ru(bpy)■-三乙胺体系ECL信号的猝灭作用,随着葡萄糖浓度的增加,其在GOx的催化下原位产生的H2O2量增多,导致ECL信号逐渐减弱,从而实现葡萄糖的检测。ECL强度与葡萄糖浓度的对数在1.0×10-8~5.0×10-5 mol/L范围内呈良好的线性关系,检出限低至5.2×10-9 mol/L。传感器具有好的稳定性和高的选择性。Pt NPs-Ru复合物为ECL传感器的构建提供了良好平台,为葡萄糖检测提供了新方法。     

玻碳电极上Ru（bpy）3^2＋的吸附及其电致化学发光的研究

通过电化学循环伏安法和电致化学发光方法,研究了Ru(bpy)32 在玻碳电极上的吸附,研究结果表明,2Ru(bpy)3 的浓度和与玻碳材料接触的时间,直接影响了Ru(bpy)32 在玻碳上的吸附.还考察了吸附的Ru(bpy)32 在玻碳电极上被氧化后脱附的情况.     

Electrochemiluminescence of tri(2,2′-bipyridine)ruthenium in aqueous solution on a gold-nanoparticle-modified glassy carbon electrode

The electrochemical behavior of electrochemical deposition of Au nanoparticles onto a glassy carbon electrode (GCE) and its application for the electrocatalytic electrogenerated chemiluminescence (ECL) of Ru(bpy)₃²⁺ in an aqueous solution without coreaction are investigated in this report. The modification of GCE by Au nanoparticles results in excellent catalysis of the ECL of Ru(bpy)₃²⁺. The effects of various factors, such as potential scan range, the presence of nitrogen and oxygen, and the scan rate on Ru(bpy)₃²⁺. ECL peaks, were systematically studied. This article has provided insight into the design of an Au-nanoparticle-modified electrode for ECL, analytical and catalytic applications. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 9, pp. 1127–1132. The text was submitted by the authors in English.     

金属离子对联吡啶钌电致化学发光影响的研究

在玻碳电极上, 联吡啶钌[Ru(bpy)₃^2＋]于＋1.50 V (vs. Ag/AgCl)左右被氧化为Ru(bpy)₃^3＋, 该氧化态离子与碱性水溶液中(pH 8.2)的OH•反应生成激发态的[Ru(bpy)₃^2＋*]而发光. 研究比较了15种金属离子对Ru(bpy)₃^2＋碱性水溶液电致化学发光的影响, 并对这些影响进行了初步的解释.     

Sensitive electrochemiluminescence resonance energy transfer(ECL-RET) between Ru(bpy)_3~(2+) and Au nanorod for hydrogen peroxide detection

Here,we developed a novel electrochemiluminescence resonance energy transfer(ECL-RET) approach between Ru(bpy)_3~(2+) and Au nanorods(NRs) for sensitive determination of H_2O_2.Au NRs were synthesized through silver ion-assisted seed-mediated method which exhibited an obvious absorption peak at about 627 nm.They were modified at glassy carbon electrode(GCE) surface which showed a significant ECL quenching efficiency about 56.5%due to the ECL-RET process.This Au NRs modified electrode was then utilized to measure the concentration of H_2O_2 on the basis of the significant quenching effect of H_2O_2 on Ru(bpy)_3~(2+) ECL.Results demonstrated that the decrement of ECL intensity at Au NRs modified electrode had ~ 6.6-fold enhancement as compared with that at bare electrode.     

基于Ru(bpy)32+-SiO2纳米颗粒的核酸适配体传感器对凝血酶的电致化学发光检测

本文应用核酸适配体构建了一种新型的电致化学发光检测蛋白体系。两个核酸适配体结合凝血酶的两个不同位点,利用这两核酸适配体与凝血酶的高亲和力构建三明治传感体系检测凝血酶。一个核酸适配体固定在金电极上用来捕获凝血酶,另一个标记有包裹电致化学发光活性物Ru(bpy)₃²⁺的二氧化硅纳米颗粒,用来检测电致化学发光信号。此核酸适配体传感器对凝血酶具有特异识别性,电致化学发光信号与凝血酶的浓度直接相关,非特异性识别的牛血红蛋白、牛血清白蛋白不干扰测定。由于在检测的核酸适配体上标记的纳米颗粒包裹有多个发光活性物,因此大大提高了发光效率和灵敏度,此法对凝血酶的线性响应范围为2.0 fmol•L^-1～2.0 pmol•L^-1,检测限可达1.0 fmol•L^-1。     

Design of a Solid‐State Electrochemiluminescence Biosensor for Detection of PML/RARα Fusion Gene Using Ru(bpy)${{{2+\hfill \atop 3\hfill}}}$‐AuNPs Aggregations on Gold Electrode

A solid‐state electrochemiluminescence (ECL) biosensor based on special ferrocene‐labeled molecular beacon (Fc‐MB) for highly sensitive detection of promyelocytic leukemia/retinoic acid receptor alpha (PML/RARα) fusion gene was developed successfully using Ru(bpy)${{{2+\hfill \atop 3\hfill}}}$ /2‐(dibutylamino)ethanol (DBAE) as detecting pattern. Such a special sensor involves two main parts, an ECL substrate and an ECL intensity switch. The ECL substrate was made by modifying the complex of Ruthenium (II) tris‐(bipyridine) and Au nanoparticles (Ru(bpy)${{{2+\hfill \atop 3\hfill}}}$ ‐AuNPs) onto the Au electrode (AuE) surface. The molecular beacon probe in which the ferrocene tag could effectively quench the ECL of the Ru(bpy)${{{2+\hfill \atop 3\hfill}}}$ acted as ECL intensity switch. The molecular beacon probe was designed with special base sequence, which could hybridize with its complementary target DNA. In the absence of a target, the hairpin structure of the probe forced the ferrocene (Fc) into close proximity with the ECL substrate, thus reducing ECL intensity. Target binding allowed the Fc away from the ECL substrate and resulted in an obvious increment in ECL intensity due to the decreased Fc quenching effect. The effect of the amount of Ru(bpy)${{{2+\hfill \atop 3\hfill}}}$ and the mixing procedure of Ru(bpy)${{{2+\hfill \atop 3\hfill}}}$ and AuNPs solution on the fabrication of ECL film had been investigated. As a result, the change of ECL intensity had a direct relationship with the logarithm of PML/RARα fusion gene concentration in the range of 0.05–500 pM with a detection limit of 7 fM, and the developed biosensor possessed good molecular recognizability in human serum. Thus, the approach holds promise for the early diagnostics and prognosis monitoring of APL and other diseases.     

Electrochemiluminescence of Ru(II) complexes immobilized on a magnetic microbead surface: distribution of magnetic microbeads on the electrode surface and effect of azide ion

The electrochemiluminescence (ECL) of magnetic microbeads modified with tris(2,2'-bipyridine)ruthenium(II) ([Ru(bpy)3]2+) was studied in the presence of tri-n-propylamine (TPA) to develop highly sensitive ECL detection system, where the employed microbead has a diameter of 4.5 microm. The ECL signal of the [Ru(bpy)3]2+ derivative-modified magnetic microbeads was found to be affected by the geometrical distribution of the magnetic microbeads on the electrode surface. The ECL peak intensity increased with increasing the number of the beads on the electrode surfaces up to 1.6 x 10(6) beads cm(-2), although above 1.6 x 10(6) beads cm(-2), it decreased. The ECL decrease arises from the physical prevention of the ECL from reaching the photomultiplier tube by the excessive beads. The observed peak ECL signal of the [Ru(bpy)3]2+ derivative-modified magnetic microbeads in the presence of NaN3, which serves as a preservative substance, mainly appeared at a potential of +0.90 V vs Ag/AgCl where [Ru(bpy)3]2+ is hardly oxidized, whereas the ECL signal in the absence of NaN3 appeared at a potential of +1.15 V. The presence of NaN3 on the electrode surface retards formation of an oxide layer on the electrode surfaces and promotes TPA oxidation. The ECL response at +0.90 V was mainly attributed to ECL reaction of excited-state [Ru(bpy)3]2+* formed by oxidation of [Ru(bpy)3]+ with TPA radical cation, where the [Ru(bpy)3]+ was generated by reduction of [Ru(bpy)3]2+ with TPA radical.     

Electrochemiluminescence Biosensor Based on PEDOT‐PSS‐ Graphene Functionalized ITO Electrode

A novel and sensitive electrochemiluminescence (ECL) method for ethanol biosensor was developed by co‐immobilizing the enzyme and ECL reagent Ru(bpy)₃²⁺ on the poly‐(3,4‐ethylene dioxythiophene) and polystyrene sulfonate functionalized graphene (PEDOT‐PSS‐G) nanocomposite film. Positively charged Ru(bpy)₃²⁺ could be immobilized effectively on the electrode surface with the negatively charged PSS and graphene, which provided a stable ECL platform for further modification with the enzyme. Moreover, the introduction of PEDOT and graphene can be acted as a conducting pathway to accelerate the electron transfer due to the high conductivity. Such biosensor combined enzymatic selectivity with the amplification of PEDOT‐PSS‐G performed well with a wide linear range, high sensitivity and good stability. The sensing platform was successfully applied to determine the amounts of alcohol in real samples.     

A Sandwich‐type Electrochemiluminescence Aptasensor for Thrombin Based on Functional Co‐polymer Electrode Using Ru(bpy)32+ Doped Nanocomposites as Signal‐amplifying Tags

Herein, a signal‐on sandwich‐type electrochemiluminescence (ECL) aptasensor for the detection of thrombin (TB) was proposed. The graphene (GR) doped thionine (TH) was electropolymerized synchronously on the bare glassy carbon electrode (GCE) to form co‐polymer (PTG) electrode. The gold nanoparticles (AuNPs) were decorated on the surface of the PTG by in‐situ electrodeposition, and the functional co‐polymer (PTG‐AuNPs) electrode was utilized as sensing interface. Then, TB binding aptamer I (TBA I) as capture probes were modified on the PTG‐AuNPs electrode to capture TB, and Ru(bpy)₃²⁺/silver nanoparticles doped silica core‐shell nanocomposites‐labeled TB binding aptamer II (RuAg/SiO₂NPs@TBA II) were used as signal probes to further bind TB, resulting in a sandwich structure. With the assistant of silica shell and AgNPs, the enrichment and luminous efficiency of Ru(bpy)₃²⁺ were significantly improved. Under the synergy of PTG‐AuNPs and RuAg/SiO₂NPs, the ECL signal was dramatically increased. The proposed ECL aptasensor displayed a wide linear range from 2 fM to 2 pM with the detection limit of 1 fM, which is comparable or better than that in reported ECL aptasensors for TB using Ru(bpy)₃²⁺ and its derivatives as the luminescent substance. The excellent sensitivity makes the proposed aptasensor a promising potential in pharmaceutical and clinical analysis.     

A Novel Electrogenerated Chemiluminescence (ECL) Sensor Based on Ru(bpy)32+‐Doped Titania Nanoparticles Dispersed in Nafion on Glassy Carbon Electrode

A novel electrogenerated chemiluminescence (ECL) sensor based on Ru(bpy)₃²⁺‐doped titania (RuDT) nanoparticles dispersed in a perfluorosulfonated ionomer (Nafion) on a glassy carbon electrode (GCE) was developed in this paper. The electroactive component‐Ru(bpy)₃²⁺ was entrapped within the titania nanoparticles by the inverse microemulsion polymerization process that produced spherical sensors in the size region of 38±3 nm. The RuDT nanoparticles were characterized by electrochemical, transmission electron and scanning microscopy technology. The Ru(bpy)₃²⁺ encapsulation interior of the titania nanoparticles maintains its ECL efficiency and also reduces Ru(bpy)₃²⁺ leaching from the titania matrix when immersed in water due to the electrostatic interaction. This is the first attempt to prepare the RuDT nanoparticles and extend the application of electroactive component‐doped nanoparticles into the field of ECL. Since a large amount of Ru(bpy)₃²⁺ was immobilized three‐dimensionally on the electrode, the Ru(bpy)₃²⁺ ECL signal could be enhanced greatly, which finally resulted in the increased sensitivity. The ECL analytical performance of this ECL sensor for tripropylamine (TPA) was investigated in detail. This sensor shows a detection limit of 1 nmol/L for TPA. Furthermore, the present ECL sensor displays outstanding long‐term stability.     

金纳米球/氮掺杂石墨烯量子点固载Ru(bpy)3^2+电致化学发光法检测邻苯二酚

利用还原法制得金纳米球(Au NPs),与氮掺杂石墨烯量子点(NG QDs)杂化后,再以壳聚糖胶黏剂并通过静电作用使Ru(bpy)3^2+负载于其表面形成复合膜,制备了一种新型的固相电致化学发光(ECL)传感器。研究发现,与单一材料相比,Au NPs和NG QDs杂化复合材料作为载体显著提高了发光试剂Ru(bpy)3^2+的ECL信号。根据环境污染物邻苯二酚对该修饰电极ECL信号较强的阻抑作用,建立了测定领苯二酚的新体系。结果表明,Au NPs/NG QDs/Ru(bpy)3^2+修饰电极的ECL信号变化值与邻苯二酚的浓度负对数在5.0 nmol/L^10μmol/L之间呈良好的线性关系,检出限为3.0 nmol/L(r=0.9992)。对5.0μmol/L的邻苯二酚进行10次重复测定,相对标准偏差为4.6%,常见的共存物质不干扰测定,表明该方法的选择性较好。采用该修饰电极成功测定了河水中的邻苯二酚含量。