Pd-Al2O3-BEA催化剂催化油脂一步加氢制航空燃油烃类性能

采用浸渍法制备了系列H-β分子筛修饰的Pd/Al₂O₃催化剂,通过XRD、低温N₂吸附、NH₃-TPD等分析表征技术和以油酸甲酯为模型化合物的加氢反应体系,探索了H-β分子筛的加入方式和含量对催化剂催化性能的影响。结果表明,由于加入方式不同,Pd-Al₂O₃-BEA催化剂组成要素之间的相互作用呈现较大差异,从而使其催化性能呈现较大不同。在Pd/（BEA-Al₂O₃）中,随着H-β分子筛加入量的增加,催化剂的比表面积、孔容、强酸酸量呈增大趋势,弱酸酸量呈先增大后减小趋势,平均孔径呈减小趋势。由于Pd/（45% BEA-Al₂O₃）催化剂具有合适的微孔孔分布、适中的强酸酸量、最大的弱酸酸量,使其呈现出最大的航空燃油烃类选择性,异构烷烃选择性和一定比例的环烷烃和芳香烃产物。     

面向异丁烷脱氢介孔γ-Al_2O_3基催化剂的合成及其高催化性能

采用溶剂蒸发自组装法调控载体形貌及孔道结构,成功制备了有序介孔氧化铝载体。以铬氧物种为活性组分,碱金属钾为助剂,采用浸渍法制备负载型催化剂,用于异丁烷催化脱氢反应,研究了反应温度、原料流速、催化剂粒径等因素对催化性能的影响。采用X射线粉末衍射、透射电子显微镜、N_2物理吸附、氢气程序升温还原及热重等表征方法探讨了载体形貌、孔道结构与催化性能的构效关系,结果表明,低温下有利于控制异丙醇铝的水解和缩合及介孔γ-Al_2O_3的研制。与常规的γ-Al_2O_3相比,所制备的介孔γ-Al_2O_3的有更大的比表面积和良好的有序性,在600℃、101.325kPa、GHSV=1 000 h~(-1)的条件下,10%(w/w)Cr_2O_3/γ-Al_2O_3催化剂性能最佳,异丁烷的转化率达63.1%,异丁烯的选择性达到85.5%。与传统的催化剂相比,介孔Cr_2O_3/γ-Al_2O_3催化剂具有大的比表面积,高度分散的活性组分,优良的催化性能和良好的抗积碳能力。     

不同金属负载对Cr/Al2O3-TiO2催化剂结构及氧化NO性能的影响

采用溶胶-凝胶法和浸渍法制备Cr/Al_2O_3-TiO_2催化剂,在考察不同Cr负载量的基础上,研究不同金属负载与焙烧温度对Cr/Al_2O_3-TiO_2催化剂结构与性能影响。程序升温氧化(TPO)结果表明,当Cr负载量为10%(w/w)时具有较好的催化活性;不同金属负载Cr/Al_2O_3-TiO_2时,负载Co及在焙烧温度为550℃时催化剂具有较好的活性。通过程序升温还原(H_2-TPR)表征发现,Co的负载使催化剂的低温氧化还原能力逐渐提高,表明Co-Cr具有较好的协同催化作用。X射线光电子能谱(XPS)表征表明,Co增加了Cr~(6+)和表面吸附氧(O_β)含量,随着焙烧温度的升高(450～550℃),晶格氧不断向催化剂表面流动,表面化学吸附氧O_β比例逐渐增加,导致催化活性不断升高,说明Cr~(6+)和O_β是催化氧化NO的重要活性物种。     

负载Ni催化剂上1,4-丁炔二醇加氢反应的载体效应研究

制备了Ni负载量为15%的3种催化剂Ni/Al_2O_3、Ni/SiO_2、Ni/ZrO_2,考察了其在1,4-丁炔二醇加氢反应中的催化性能,结合XRD、H_2-TPR、H_2-TPD、N_2物理吸附等表征,研究了载体性质对催化剂1,4-丁炔二醇加氢性能的影响.结果表明,Ni/SiO_2催化剂上,由于Ni与SiO_2间弱的相互作用,Ni物种主要以大晶粒形式存在,产生大量弱吸附H_2物种,有利于低温下1,4-丁炔二醇加氢,在温度50℃,氢气压力1 MPa时,反应2 h可实现1,4-丁炔二醇的完全转化,1,4-丁烯二醇和1,4-丁二醇选择性分别达到68.1%与18.2%.Ni/Al_2O_3中Ni与载体间具有强相互作用,主要存在Ni-Al_2O_3界面或溢流到Al_2O_3载体表面的强吸附H_2物种,而Ni表面的弱吸附H_2物种较少,催化加氢活性明显降低.Ni/ZrO_2中由于还原过程中ZrO_2的迁移包裹作用,Ni表面低温吸附H_2物种最少,活性最低,1,4-丁炔二醇转化率仅为8.1%,主产物为1,4-丁烯二醇.     

CeO2改性Ag-V2O5/TiO2催化剂的甲基吡啶氧化脱甲基性能

以锐钛矿TiO_2为载体,考察了CeO_2改性对Ag-CeO_2-V_2O_5/TiO_2催化3-甲基吡啶氧化脱甲基性能的影响,并优化了催化剂组成与制备条件.结果表明:Ce掺杂改性不仅能够与V物种作用形成Ce VO_4,而且促进V_2O_5分散,改善活性组分的氧化还原性能,从而提高3-甲基吡啶脱甲基转化率与选择性,改善Ag-V_2O_5/TiO_2催化性能.适宜的催化剂组成为V_2O_5负载量15%,Ce/V的摩尔比0.33,Ag质量分数1.0%.过高的焙烧温度将导致TiO_2载体向金红石型转变,Ag-CeO_2-V_2O_5/TiO_2适宜制备条件为450℃焙烧4 h.     

水热改性对铝基载体孔结构及异丁烷脱氢性能的影响

分别以两种水热介质对γ-Al_2O_3载体进行水热改性,并将改性后的载体负载CrO_x后应用于异丁烷催化脱氢,考察了水热温度对载体物化性质以及水热改性对催化脱氢性能的影响。通过XRD、N_2吸附-脱附及H_2-TPR对载体结构进行表征。结果表明,水热改性使γ-Al_2O_3发生再水合过程,焙烧后,结晶度变好,活性组分与载体的相互作用增加,CrO_x/Al_2O_3催化剂的异丁烷脱氢性能得到改善。以盐溶液水热改性载体,140℃处理4h,CrO_x/Al_2O_3催化剂表现出较好的异丁烷脱氢性能,10h内异丁烷脱氢平均转化率为43.04%,平均选择性86.34%,失活参数13.7%。     

Pd/CuxCo3-xOn界面的可控制备及高效催化甲苯燃烧反应

采用水热合成法制备了形貌规整且主要暴露晶面为(112)面的Co_3O_4六角片,在此基础上掺杂了适量的Cu元素,并且可控沉积了窄尺寸分布的Pd粒子。制备过程简单、绿色且产率高。所得材料应用于催化甲苯完全氧化反应时表现出优异的催化性能,其中Pd/h-Cu_(0.18)Co_(2.82)O_n的T_(90)(甲苯的转化率达到90%时的反应温度)低至198℃。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、比表面积测试(BET)、H2程序升温还原(H2-TPR)、X射线光电子能谱(XPS)对催化剂的结构和理化性质进行了表征。结果表明,适宜量的Cu掺杂后Co_3O_4基底氧空位增多,活化氧的能力增强,表面存在丰富的吸附氧物种,表现出与贵金属基催化剂相媲美的催化活性。引入的Pd组分主要以PdO形式存在,基底Cu掺杂进一步提升了Pd的氧化态,表面高反应性的氧种更多,反应活性更高。     

CoAl_2O_4/蜂窝陶瓷催化剂的制备及其催化臭氧化性能

采用涂覆法制备了CoAl_2O_4/蜂窝陶瓷催化剂。利用X射线衍射、N_2吸附-脱附和透射电镜等方法对所制备的催化剂进行了表征,并分析了其催化臭氧化降解对苯二酚的效能。结果表明,CoAl_2O_4/蜂窝陶瓷的晶相属于典型的尖晶石结构,具有较大的比表面积、孔容和孔径,分别达到77 m~2·g~(-1)、0.001 7 cm~3·g~(-1)和3.9 nm。CoAl_2O_4/蜂窝陶瓷催化臭氧化对苯二酚的去除率高达81.2%,COD去除率可达47.7%。在叔丁醇存在的条件下,对苯二酚的去除率显著下降,说明CoAl_2O_4/蜂窝陶瓷催化臭氧化遵循羟基自由基机理。     

ZrO4/SiO2-Al2O3催化肉桂醛MPV转移加氢性能

以九水合硝酸铝（Al（NO₃）₃·9H₂O）与正硅酸乙酯（TEOS）为前驱盐,采用溶胶-凝胶法制备一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,并通过浸渍硝酸氧锆引入ZrO₂,制备ZrO₂/SiO₂-Al₂O₃复合氧化物催化剂,考察催化剂在肉桂醛（CAL）MPV转移加氢中的催化性能,并结合N₂物理吸附、X射线粉末衍射（XRD）、傅里叶变换红外光谱（FTIR）、NH₃-程度升温脱附（NH₃-TPD）、Py-原位红外（Py-IR）等技术,研究催化剂结构、织构以及表面性质与其催化性能间的构效关系.研究表明,所制备的催化剂均以L酸为主,并含有少量B酸中心,这使得加氢产物以肉桂醇（COL）为主,并含有少量1-苯丙烯-2-丙基醚（CPE）.Al₂O₃含量不仅影响催化剂表面的酸中心数量,而且对催化剂的织构参数有较大影响.随Al₂O₃含量的增加,催化剂表面L酸与B酸中心均有所增加,而孔径则持续变小,这使得催化反应呈现CAL转化率先增加后减少、目标产物COL选择性先稍有减小后有所增加的趋势.在Si/Al比为2时,催化剂具有最优的催化性能,优化反应条件下,CAL转化率达96%,目标产物COL选择性达90%.     

g-C3N4/双钙钛矿复合材料的制备及氧催化性能

通过溶胶-凝胶法制备出不同Ni掺杂比例的双钙钛矿Sr_2Ni_xCo_(2-x)O_6(x=0.2,0.4,0.6,0.8),通过热分解法制备出具有层状结构的纳米颗粒g-C_3N_4,并制备其复合物催化剂。将双钙钛矿和g-C_3N_4分别制备成双功能电极片,用于测试其对氧还原(ORR)和氧析出(OER)的催化活性,然后选取具有最佳氧催化活性的Ni掺杂比例x=0.4的双钙钛矿与一定重量比例的g-C_3N_4进行复合,测试复合催化剂的氧催化活性。结果表明,复合后的催化剂催化效果明显优于单一催化剂,当g-C_3N_4添加量占双钙钛矿的30%(w/w)时复合催化剂催化氧还原反应的最大电流密度为395.7 mA·cm~(-2)(-0.6 V vs Hg/HgO),氧析出反应的最大电流密度为372.0mA·cm~(-2)(1 V vs Hg/HgO),这表明g-C_3N_4与Sr_2Ni_(0.4)Co_(1.6)O_6复合后协同催化能够提高双钙钛矿的氧催化活性。     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

NaBO2-NaCl-Na2CO3, NaBO2- Na2CO3-NaMoO4, NaBO2- Na2CO3-NaWO4, and NaBO2-NaCl-Na2WO4 ternary systems

The phase diagrams of the NaBO₂-NaCl-Na₂CO₃, NaBO₂-Na₂CO₃-Na₂MoO₄, NaBO₂- Na₂CO₃-Na₂WO₄, and NaBO₂-NaCl-Na₂WO₄ ternary systems were studied by a calculation-experimental method and differential thermal analysis. The coordinates of ternary eutectics were determined: E ₁: 612°C, 16 mol % NaBO₂, 42 mol % NaCl, and 42 mol % Na₂CO₃; E ₂: 568°C, 12 mol % NaBO₂, 28 mol % Na₂CO₃, and 60 mol % Na₂MoO₄; E ₃: 575°C, 12 mol % NaBO₂, 32 mol % Na₂CO₃, and 56 mol % Na₂WO₄; E ₄: 628°C, 8 mol % NaBO₂, 20 mol % NaCl, and 72 mol % Na₂WO₄; and E ₅: 655°C, 9 mol % NaBO₂, 53 mol % NaCl, and 38 mol % Na₂WO₄.     

Structural chemistry of Sr3Cr2WO9, Ca3Cr2WO9, and Ba3Cr2WO9

We have studied the preparation and crystallographic structure of three perovskite-type compounds: Sr₃Cr₂WO₉, cubic, the lattice parameter of which is a = 7.812Å; Ca₃Cr₂WO₉, tetragonal, the lattice parameters of which are a = 5.408 Å and c = 7.635Å; and Ba₃Cr₂WO₉, hexagonal, the lattice parameters of which are a = 5.691 Å and c = 13.957Å. We have compared these three structures and shown the relationship between the dimensions of the alkaline-earth metal and the existence of the different structures.     

Theoretical study of polyoxide clusters B20O30, Al20O30, V20O50, Si20O30H20, and Si20O30F20

The structural, electronic, and vibrational characteristics and energies of the isolated polyoxide clusters B₂₀O₃₀, Al₂₀O₃₀, V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀ and their complexes with the H⁻ ion and ammonia complexes Al₂₀O₃₀ · nNH₃ have been calculated by the density functional theory B3LYP method with different basis sets. The computation results show that the symmetric closo structure I _h with oxygen bridges located above the centers of the faces of an empty [M₂₀] dodecahedron is more favorable for V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀. For B₂₀O₃₀, the cage closo isomer is also more favorable than the other isomers, but its structure is severely distorted as compared to a dodecahedron and has a symmetry close to C ₃ . For Al₂₀O₃₀, the I _h structure corresponds to a high-lying local minimum of the potential energy surface. For Al₂₀O₃₀, a set of unusual puckshaped isomers of symmetry C _i , with different numbers of four-coordinate atoms ^IVAl and three-coordinate atoms ^IIIO, was localized; these structures are more than 90 kcal/mol more favorable than the dodecahedron I _h . The most favorable isomer of Al₂₀O₃₀ contains twelve four-coordinate atoms ^IVAl and four five-coordinate atoms ^VAl. The energies of dissociation of the most favorable M₂₀O₃₀ clusters into the M₂O₃ (C _2v ) and M₄O₆ (T _d ) fragments and, in the case of Al₂₀O₃₀, also into the Al₈O₁₂ (O _h ) and Al₁₂O₁₈ (D _3d ) fragments, have been estimated. The conclusion has been drawn that these clusters can, in principle, exist and can be experimentally detected in the isolated state. Analogous calculations have been performed for ammonia complexes Al₂₀O₃₀ · nNH₃ with n varying from 1 to 20. The effect of solvation on the relative stability of the dodecahedral and puckshaped isomers of the Al₂₀O₃₀ cluster is observed. The isomers with ammonia molecules in their first coordination sphere become much closer to one another on the energy scale; however, the dodecahedron remains a considerably less favorable intermediate. Original Russian Text ? O.P. Charkin, N.M. Klimenko, D.O. Charkin, 2008, published in Zhurnal Neorganicheskoi Khimii, 2008, Vol. 53, No. 4, pp. 624–635.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.