邻溴苯甲酸电化学脱溴反应的原位红外光谱研究

采用循环伏安法研究了水溶液中邻溴苯甲酸在不同电极上的电化学还原脱溴反应,与Ti和C电极相比,Cu电极对邻溴苯甲酸有较好的电化学还原活性。同时采用电化学原位红外反射光谱对其反应机理进行了系统分析,结果表明：邻溴苯甲酸在Cu电极上的电还原脱溴反应是一个脱溴加氢的过程,邻溴苯甲酸在电极表面首先得到一个电子变成邻溴苯甲酸自由基负离子;然后脱去溴离子得到苯甲酸自由基,该自由基再得到一个电子变成苯甲酸负离子;最后加成氢质子得到最终产物苯甲酸,这一产物已经通过恒电流电解实验得到了进一步的证实。     

酸性介质中碘离子在铂电极上的电化学氧化行为

采用循环伏安法研究了酸性介质中碘离子在铂电极上不同电位区间, 不同酸度下的电化学反应行为. 结果表明, 当极化电位较低(小于0.6 V(vs Hg/Hg2SO4))时, 碘离子在铂电极上发生2I--2e→I2电氧化反应, 反应产物通过I2+I-=I-3被进一步溶解, 整个反应属于E-C(electrochemical-chemical)模式. 电氧化过程中可以形成碘膜, 其也可以被碘离子溶解. 当极化电位升高至0.6 V(vs Hg/Hg2SO4)或以上时, 碘离子会直接电氧化为高价态碘化合物, I-+3H2O→IO-3+6H++6e, 而析出的碘膜并不发生再氧化反应; 在电化学还原过程中, 出现了两个还原峰, 分别对应于I2、I-3的还原反应; 在无碘膜时, 碘离子电氧化过程受溶液中碘离子的液相扩散步骤控制; 碘膜形成后, 主要受碘膜中碘离子的固相扩散控制; 酸度对于碘离子的电化学氧化过程有很大的影响, 其线性极化曲线的起峰电位及电流峰值电位均随酸浓度升高而负移.     

间氯苯甲酸在Pd/Ti电极上的电化学脱氯反应

以Ti为基底电极, 在PdCl₂溶液中电沉积制备了Pd/Ti电极, 采用SEM和XPS进行表征. 采用循环伏安法研究了Cu, Ag, Ti和Pd/Ti电极对间氯苯甲酸(3-CBA)的电还原特性, 与Cu, Ag和Ti电极相比, Pd/Ti电极对3-CBA有较好的电化学还原活性. 同时采用电化学原位红外反射光谱对3-CBA在Pd/Ti电极上的电还原反应机理进行了系统分析, 结果表明3-CBA在Pd/Ti电极上的电化学脱氯反应是一个脱氯加氢过程, 3-CBA首先得到一个电子形成阴离子自由基中间体, 随后释放一个氯离子, 产生苯甲酸盐的自由基, 最后该自由基得到一个电子并夺取一个氢质子, 在电极表面脱去氯得到最终产物苯甲酸.     

碳纳米管/聚对甲基吡啶修饰电极测定硝基苯甲酸

采用滴涂法和循环伏安法在玻碳电极上电沉积一层稳定的单壁碳纳米管/聚对甲基吡啶纳米薄膜(SWNTs/POMP)。研究了邻、对硝基苯甲酸在此修饰电极上的电化学行为,建立了电化学同时测定邻、对硝基苯甲酸的新方法。实验结果表明:在0.1 mol/L HClO4溶液中,邻、对硝基苯甲酸在SWNTs/POMP电极上发生不可逆的还原反应,由于碳纳米管和聚合物薄膜的协同效应,SWNTs/POMP电极对邻、对硝基苯甲酸有很好的的电催化作用,并对其响应进行了定量分析。     

聚邻氨基苯甲酸-铜复合薄膜修饰电极的制备及其电化学性能

利用聚合物官能团对金属离子的配位作用,在电极表面原位制备了金属粒子。 首先在玻碳电极（GCE）表面电沉积聚邻氨基苯甲酸(PoABA),再化学吸附铜离子(Cu2+),用水合肼还原得到单质铜(Cu0)。 采用扫描电子显微镜和能谱分析表征了聚邻氨基苯甲酸 铜(PoABA-Cu0)复合薄膜的表面形貌和元素构成,研究了PoABA-Cu0修饰电极的电化学性能,并以其检测了过氧化氢（H2O2）。 结果表明,电极表面被修饰上了一层PoABA-Cu0复合薄膜;制备的修饰电极对H2O2具有良好的电催化性能,在邻氨基苯甲酸的聚合圈数为10、Cu2+的吸附时间为10 min、工作电压为-0.3 V时,该修饰电极对H2O2表现出了最佳的检测性能,其线性浓度范围为5.0×10-5～1.0×10-2 mol/L,灵敏度为96.3 μA·L/(mmol·cm),检测限为5.0×10-5 mol/L,且具有较好的稳定性。     

新型铜配合物修饰热解石墨电极上的氧电催化还原

 采用新型单核铜配合物高氯酸咪唑N-2-羟基乙基二乙烯三胺合铜(Ⅱ)(Cu［L(ImH)］(ClO4)2)修饰热解石墨(PG)电极表面制得了Cu［L(ImH)］/PG电极,并采用循环伏安法和电位阶跃实验研究了该电极对氧的催化还原作用. 结果表明,该电极在中性和碱性条件下对氧气的催化还原具有良好的稳定性,还原峰电流随电位扫描速度的增大而增强,Ip～v1/2呈线性关系. 根据电位阶跃实验的I～t-1/2曲线,计算出电极反应的电子转移数约为4, 推断氧气在该电极上的还原是经历了4电子过程还原为水,催化机理属于混合控制的ECE (E电极反应, C化学反应)过程.     

聚苯胺修饰超微盘电极上镉(Ⅱ)的表面络合吸附波

用直径7 μm的碳纤维组合成超微圆盘电极,以聚苯胺修饰电级.以阶梯扫描法、循环伏安法、双阶跃计时电量法和交流阻抗法等,研究了Cd2＋在该电极上的表面络合吸附特性和电极过程.在循环伏安图上出现两个还原峰,实验和理论都证明,由于电极表面的聚苯胺对Cd2＋的特性吸附,形成电活性的表面吸附态络合物.因此,这种表面络合物首先被还原,形成峰电位－0.90 V处的表面络合吸附波,还原峰电位比Cd2＋直接还原电位（－0.98 V）正移,循环反扫时,氧化波无峰形.根据实验数据推测了电极过程的反应机理,证实该还原波具有扩散和表面反应同时控制的表面络合吸附波的特性.理论计算与实验基本一致,并求得了表面吸附态配合物的形成常数、吸附量和表面络合反应的动力学参数.实验还证实,在峰电位－1.06 V 处的还原波,是Cd2＋的表面吸附还原态诱导而产生的催化氢波.     

聚氯乙烯膜碘离子选择电极在溴碘离子共存体系分析中的应用

介绍了聚氯乙烯膜碘离子选择电极(PVC-I-ISE)的制备方法,电极对碘离子的能斯特响应斜率为59 mV/pI,响应的线性范围为4.0×10-5~1.0×10-2mol.L-1,检出限为1.6×10-5mol.L-1,低于用银ISE的检出限,电极的使用寿命为一个月以上。将制备的碘离子选择电极作为指示电极用于对溴、碘混合离子体系进行连续分别电位滴定,并与以银电极为指示电极的电位滴定方法进行了比较。结果表明用PVC-I--ISE作指示电极,可在I--Br-共存的混合溶液中进行两离子的连续电位滴定,而用银-ISE时则不能。     

结晶紫选择电极的制备及催化电位法测定碘的研究

根据磷酸介质中碘离子催化高碘酸钠氧化结晶紫的氧化还原反应,应用自制的结晶紫选择电极跟踪紫的 度变化,对催化电位法测定碘进行了研究。测定碘离子 的线性范围为０．２０－５．５μｇ／２５ｍＬ,方法检出限为４．１＊１０＾－９ｇ／ｍＬ。该方法应用于测定食盐和饮用水中碘含量,ＲＳＤ〈４．１％,平均回收率为９５．１％。     

电流型聚吡咯碘离子化学修饰电极的制备与性能研究

在玻碳电极(GCE)表面上修饰了一层导电聚合物 聚吡咯(Ppy)薄膜,用循环伏安法制备了新型的基于电流响应的掺杂碘离子的聚吡咯修饰电极;研究了电极的电化学特性。此修饰电极对碘离子的响应是基于碘离子在Ppy膜与电解质溶液中的掺杂平衡以及Ppy膜中的碘离子在修饰电极表面的氧化还原过程;制成的电流型电极对5 0×10-2mol/L～1 0×10-5mol/L的碘离子呈良好的线性响应关系,检出限为6 0×10-6mol/L。     

Dissociative electron transfer to organic chlorides: electrocatalysis at metal cathodes

The reductive cleavage of a series of organic chlorides, including chloroaromatics, benzyl chlorides, activated chloroalkanes and polychloromethanes, was investigated at Ag, Cu, Pd and glassy carbon (GC) electrodes in CH(3)CN + 0.1 M (C(2)H(5))(4)NClO(4). The silver cathode was either a 2-mm diameter disc, fabricated from Ag wire, or nanoclusters of average diameter d = 304 nm, prepared by electrodeposition on GC. Ag, Cu and Pd electrodes have shown remarkable electrocatalytic properties for the reduction of several compounds. The peak potentials recorded at these electrodes, for example, at upsilon = 0.1 V s(-1) are positively shifted by 0.3-0.8 V with respect to the reduction potentials measured at a non catalytic electrode such as GC. Electrocatalysis is strictly related to the concerted nature of the dissociative electron transfer to the carbon-chlorine bond. No catalysis is observed when the dissociative electron transfer to RCl occurs according to a stepwise mechanism involving the intermediate formation of a radical anion. The catalytic surfaces affect the reaction scheme, offering a more favourable route possibly through the formation of strongly adsorbed activated complexes.     

Preparation and Electrochemical Properties of the Pd-modified Cu Electrode for Nitrate Reduction in Water

The reduction of nitrate has gained renewed attention due to environmental problems like overfertilization and the increasing costs of purification of drinking water. The usual techniques (e.g. ion-exchange and biofiltration) have some disadvantages1. So …     

Nafion膜电极对氧的催化还原的研究(I)──CoTSPc和CoTMAP的循环伏安对比

制备了两组Nafion膜电极(膜中分别分布有带正、负电荷的过渡金属大环配离子),并用循环伏安法研究比较了这两组电极对氧催化还原性能,探讨了配离子和Nafion膜之间的静电作用对电极催化性能影响的规律,同时对其它因素的影响及电荷在Nafion膜中传递的机理也进行了讨论。     

Electro-oxidation of formic acid catalyzed by FePt nanoparticles

The electrocatalytic oxidation of formic acid at a gold electrode functionalized with FePt nanoparticles was studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) in a mixed solution of 0.1 M HCOOH and 0.1 M HClO4. The FePt bimetallic nanoparticles, with a mean diameter of 3 nm, were prepared by a chemical reduction method. The Au/FePt nanostructured electrode was prepared firstly by the deposition of FePt nanoparticles onto a clean Au electrode surface, followed by ultraviolet ozone treatment to remove the organic coating. In CV measurements, two well-defined anodic peaks were observed at +0.20 and +0.51 V (vs. a Ag/AgCl quasi-reference). The anodic peak at +0.20 V was attributed to the oxidation of HCOOH to CO2 on surface unblocked by CO, whereas the peak at +0.51 V was ascribed to the oxidation of surface-adsorbed CO (an intermediate product of HCOOH oxidation) and further oxidation of bulk HCOOH. From the onset potential and current density of the electro-oxidation of HCOOH, FePt nanoparticles exhibit excellent electrocatalytic activities as compared to Pt and other metal alloys. EIS measurements were carried out to further examine the reaction kinetics involved in the HCOOH electro-oxidation. The EIS responses were found to be strongly dependent on electrode potentials. At potentials more positive than -0.25 V (vs. Ag/AgCl), pseudo-inductive behavior was typically observed. At potentials between +0.3 and +0.5 V, the impedance response was found to reverse from the first quadrant to the second quadrant; such negative Faradaic impedance was indicative of the presence of an inductive component due to the oxidation of surface-adsorbed CO. The impedance responses returned to normal behavior at more positive potentials (+0.6 to +0.9 V). The mechanistic variation was attributed to the formation of different intermediates (CO or oxygen containing species) on the electrode surface in different potential regions. Two equivalent circuits were proposed to model these impedance behaviors.     

基于纳米银-石墨烯复合材料的增强效应电化学测定对乙酰氨基酚

利用氧化还原反应制备纳米银-石墨烯复合纳米材料(Ag NPs-GN),将其修饰在玻碳电极表面制备了纳米银-石墨烯修饰玻碳电极(Ag NPs-GN/GCE)。在p H 4.78的Britton-Robinson(B-R)缓冲溶液中,用循环伏安法(CV)和方波伏安法(SWV)研究了对乙酰氨基酚在Ag NPs-GN/GCE和GN/GCE上的电化学行为。结果表明,二者对对乙酰氨基酚的氧化还原反应均有电催化作用,而且复合纳米材料Ag NPs-GN具有较单一GN更好的催化效果。用方波伏安法测得对乙酰氨基酚的还原峰电流与其浓度在1.0×10-7~5.0×10-4mol/L范围内呈线性关系,检出限(S/N=3)为3.0×10-8mol/L。建立了片剂中对乙酰氨基酚含量测定的新方法,修饰电极具有较好的重现性和稳定性。     

NaOH溶液中Ni基石墨修饰电极上甲醇电氧化过程中钴与铜的协同效应

在NaOH溶液(0.1 mol/L)中考察了Ni, Co和Cu二元和三元合金修饰的石墨电极上甲醇电氧化反应性能.采用循环伏安法、计时电流法和电化学阻抗谱(EIS)等技术研究了修饰电极的催化活性和协同效应.这些催化剂在含有Ni, Cu和Co离子溶液的阴极电位上反复浸渍石墨电极制得.结果表明,在甲醇存在下, Ni基三元合金修饰电极(G/NiCuCo)对甲醇氧化反应的响应值明显高于其它样品.阳极峰值电流与扫描速率的平方根呈线性关系,表明该过程受扩散控制.在CA区域,该反应遵循Cottrellin特性,甲醇扩散系数为6.25×10–6 cm2/s.甲醇氧化反应速率常数为40×107 cm3/(mol·s).另外,采用EIS研究了修饰电极表面上甲醇催化氧化反应.     

Electrochemical Determination of NDPhA via its Electrocatalysis at Porous Au Electrode in Room Temperature Ionic Liquid

N‐Nnitrosodiphenylamine (NDPhA) is a typical kind of nonvolatile nitrosamine. Its electrochemical oxidation occurs usually at relative positive potentials (>1.1 V) even at catalytic noble metal electrodes in aqueous solutions. The formation of oxide and evolution of oxygen at such high potentials makes the analysis of NDPhA on noble metal electrodes difficult. Accordingly, its electrochemical analysis is usually performed in anhydrous organic electrolytes. In this work, room temperature ionic liquid [BMIM⁺] [BF ] acting as electrolyte was introduced in this electrochemical analysis systems. It acts as supporting electrolyte itself, has good solubility of organic compounds, and allows a wide performance potential window of noble electrode, and in turn, highly electrocatalytic noble electrode of platinum or gold can be used as working electrodes. After the investigation of the electrocatalytic behavior of NDPhA at a gold electrode in this room temperature ionic liquid electrolyte, high sensitive determination of NDPhA was designed. It is demonstrated that the electrochemical response of NDPhA is determined by a surface‐controlled process. Therefore, a sensor with high sensitivity was constructed by applying porous Au electrodes with highly electrocatalytic activity and large active surface area. The present approach on one hand broadens the application field of room temperature ionic liquids, and on the other hand provides a sensitive analytical method for environmental detection.     

氧化铁电极的半导体性能和光电化学 Ⅴ.烧结掺锌氧化铁电极的光电响应

Somorjai等曾报道在不同电势下,测得掺MgO氧化铁光电极具有n,p两种类型的光响应^[1]。最近本实验室首次报道了在同一电势下,热形成的掺MgO-Fe₂O₃光电极具有n,p型双重光响应共存现象^[2],由于其在电催化等中可能的应用价值引起了较广泛的兴趣。     

Adsorption of 4-aminopyridine on Co and Ag electrodes probed by SERS

The adsorption of 4-aminopyridine (4-AP) on Co and Ag electrodes in acid or alkaline solutions of KCl and KI electrolyte salts were monitored by the Surface-enhanced Raman Spectroscopy (SERS) technique. The SERS intensity for the Ag electrode was in 2 orders of magnitude higher than for the Co electrode, due to the enhancement of the Raman cross-section on Ag by the surface-plasmon excitation. In acidic chloride medium (pH 4), the SERS results for Ag electrodes indicate that the protonated form of 4-AP (4-APH⁺) adsorbs in the potential range of −0.1 to −0.6 V (Ag|AgCl|KCl sat) through hydrogen-bonding between 4-APH⁺ and Cl⁻ adsorbed on the electrode surface; at more negative potentials the neutral form 4-AP is the predominant adsorbed species. For Co electrode in the same medium, only bands due to neutral 4-AP were observed in the spectra at −0.8 and −0.9 V. For more negative potentials bands assigned to both 4-AP and 4-AP surface complex are observed, with the lasts being enhanced, as the potentials are turned more negative. In alkaline chloride medium (pH 13), for less negative potentials the bands assigned to free 4-AP were observed in the spectra of both Ag and Co surfaces. For more negative potentials, only bands assigned to the 4-AP surface complex were observed. For 0.1 mol L⁻¹ KI acidic or alkaline solutions, bands assigned to 4-AP and 4-APH⁺ were observed in a wider potential range than in chloride solutions. An adsorption scheme of 4-AP on Ag and Co is proposed for acidic and alkaline solutions.     

Electrochemical Reduction of Monochlorinated Hydrocarbons at a Hydrophobic Zn/PTFE Composite‐Electroplated Zn Electrode in a Water‐Acetonitrile Mixture

Composite‐electroplating of zinc particles with polytetrafluoroethylene at a zinc substrate resulted in a working electrode which could be used at high negative potentials (to ?2.5 V vs. Ag/AgCl) without significant hydrogen evolution. The electrodes were characterized by SEM and CV and were used to detect organochloride compounds in a water‐acetonitrile mixture, by potential step methods.