Characterization of cross-linking structure in terephthalate polyesters formed through material recycling process by pyrolysis-gas chromatography in the presence of organic alkali

Typical terephthalate polyesters such as poly(butylene terephthalate) (PBT) and poly(ethylene terephthalate) (PET) were characterized by pyrolysis-gas chromatography (Py-GC) in the presence of tetramethylammonium hydroxide in terms of the cross-linking structure formed during their material recycling. In the pyrograms of PBT and PET thermally treated at 270 °C for 1 h, which were prepared as model polymers containing cross-linking structures, an additional peak was commonly observed as well as the main reactive pyrolysis products for the original polyesters such as dimethyl terephthalate. Based on the observed spectra obtained by Py-GC/mass spectrometry and Py-GC/Fourier transform infrared spectrometry measurements, this peak was assigned to the product reflecting a biphenyl-type cross-linking structure. Furthermore, in the pyrograms of kneaded PBT and PET samples also at 270 °C for a total of 1 h, which were prepared to simulate material recycling, the same peak for the cross-linking structure was also observed, although its intensity was slightly lower than that in the samples thermally treated in air. This fact verified that the biphenyl-type cross-linking structure would be considerably formed during the recycling of PBT and PET, which might in turn contribute to the deteriorated properties of the recycled materials from waste polyesters. Moreover, difference in the formation of the cross-linking between PBT and PET is discussed on the basis of the observed results.     

Some Comments on a Recent Article Dealing with Three Aliphatic-Aromatic Polyesters and Their Spectral Identification

This work discusses the results appearing in Wu et al.’s (2014) article dealing with three aliphatic-aromatic polyesters based on terephthalic acid and their spectral identification. Using an instrument equipped with a switch that allows ions with masses below 5 kDa to be discarded (ion deflector), the authors report the MALDI spectrum of a commercial poly(ethylene terephthalate) with signals up to 80 kDa. I plot the spectral intensities and fit them with a Gaussian curve. The result is carefully examined. Thereafter, attention is moved to the MALDI spectra obtained when the ion deflector is turned off. A computation that gives the number-average and the weight-average molar mass (Mn and Mw) was performed, but the result was Mn = 1362 g/mol and Mw = 1416 g/mol. These values are much too low and they cannot be used. In order to explain this failure, I modified a model developed for poly(pentylene adipate). This hypothesis is discarded and the correct explanation is found. I also discuss other types of instrumentation, for instance, Py-GC/MS combined with library-search and also NMR spectroscopy, with specific reference to the chemical shifts of the -CH2- protons in aliphatic-aromatic polyesters.     

Thermal degradation mechanisms of liquid crystalline aromatic polyesters studied by pyrolysis–gas chromatography/mass spectrometry

The thermal degradation mechanisms of liquid crystalline aromatic polyesters (LCPs) prepared from p-hydroxybenzoic acid (PHB), biphenol (BP), and terephthalic acid (TA) were studied by pyrolysis–gas chromatography/mass spectrometry (Py-GC/MS). The LCP containing deuterated terephthalate units and the LCPs that have different comonomer ratios were examined. On the basis of the pyrolysis products determined, the origin of the main pyrolysis products (benzene, phenol, biphenyl, phenyl benzoate, etc.) from the corresponding comonomer units were estimated and their thermal degradation mechanisms were eventually discussed in detail.     

Isothermal melt-crystallization and melting behavior for three linear aromatic polyesters

Isothermal crystallization and subsequent melting behavior for three different types of linear aromatic polyester, namely poly(ethylene terephthalate) (PET), poly(trimethylene terephthalate) (PTT), and poly(butylene terephthalate) (PBT), were investigated (with an emphasis on PTT in comparison with PET and PBT). These polyesters were different in the number of methylene groups (i.e. 2, 3, and 4 for PET, PTT, and PBT, respectively). Isothermal crystallization studies were carried out in a differential scanning calorimeter (DSC) over the crystallization temperature range of 182-208 °C. The wide-angle X-ray diffraction (WAXD) technique was used to obtain information about crystal modification and apparent degree of crystallinity. The kinetics of the crystallization process was assessed by a direct fitting of the experimental data to the Avrami, Tobin, and Malkin macrokinetic models. It was found that the crystallization rates of these polyesters were in the following order: PBT>PTT>PET, and the melting of these polyesters exhibited multiple-melting phenomenon. Lastly, the equilibrium melting temperature for these polyesters was estimated based on the linear and non-linear Hoffman-Weeks (LHW and NLHW) extrapolative methods.     

Determination by MALDI-TOF MS of the structures obtained from polytransesterification of diethyl 2,6-pyridinedicarboxylate and poly(ethylene glycol)

Polyesters from reaction of diethyl 2,6-pyridinedicarboxylate with poly(ethylene glycol) 1000 were synthesized through a polytransesterification process using titanium(IV) alkoxide as catalyst. The resulting polyesters were characterized by size-exclusion chromatography (SEC) and matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF MS). The structures of the polyesters were established and revealed the formation of several cyclic and linear populations of varying size. Detailed analysis of the MALDI-TOF mass spectra of the obtained polyesters has revealed the presence of linear polycondensates bearing various end groups among which those attributed to an exchange reaction between alkyl groups of the catalyst and ester groups of the polycondensates.     

Study on pyrolysis behaviors of L-tyrosine-based phthalonitrile resin

The pyrolysis behaviors of l-tyrosine-based phthalonitrile(TPN) resin were investigated by thermogravimetric-Fourier transform infrared spectrometry-mass spectrometry (TG-FTIR-MS) and Pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS). The small molecules produced during pyrolysis process of TPN resin were tracked in real time by TG-FTIR-MS. The larger molecules (m/z > 40) from fast pyrolysis at 900 °C of the TPN resin using Py-GC/MS were identified. From TG-FTIR-MS and Py-GC/MS results, the production pathways of pyrolysis products such as CO₂, CO, NH₃, benzonitrile and phenol were analyzed. The possible pyrolysis mechanism of TPN resin under non-oxidizing gaseous environment was proposed. The results of this study provide the useful information for designing the molecular structure of l-tyrosine-based polymers which possessing high thermal stability.     

反相高效液相色谱/基质辅助激光解吸电离飞行时间质谱 分离鉴定螺蛳血管紧张素转换酶抑制肽

运用反相高效液相色谱(RP-HPLC)对酶解螺蛳腹足肌得到的血管紧张素转换酶(ACE)抑制肽进行两步分离提纯,第一步主要得到8个组分;选取其中活性最高的组分进一步分离,得到2个组分,其中活性较高组分的ACE半抑制浓度为43.5 μmol/L,基本为单一肽组分。对提纯的组分分别使用高效液相色谱/电喷雾离子质谱法(HPLC/ESI-MS)和基质辅助激光解吸电离飞行时间质谱法(MALDI-TOF MS)进行分析,同时结合氨基酸组成分析结果,最终得到的肽链一级结构为Lys-Glu-Ile-Trp(KEIW),符合已知的高活性ACE抑制肽的结构规律。经过对两种方法分析过程的比较,认为ESI-MS可以得到多方面的信息,但无法确定肽的序列;MALDI-TOF MS可以得到精确的二级质谱图(m/z精确至0.0001),从而可以得到确定的肽的序列。     

Identification of polymer building blocks by Py–GC/MS and MALDI-TOF MS

The main goal of this work is to identify polyurethane (PU) building blocks by pyrolysis gas chromatography/mass spectrometry (Py–GC/MS) and matrix-assisted laser desorption/ionization-time of flight mass spectrometry (MALDI-TOF MS). Toluene diisocyanate (TDI) and diphenylmethane diisocyanate (MDI) are widely used polymer building blocks. Py–GC/MS and MALDI-TOF MS were proved to be powerful methods to distinguish TDI-PU and MDI-PU according to the characteristic pyrolysis products and the different repeated units, respectively. In Py–GC/MS, the specific pyrolyzates are TDI for TDI-PU and MDI for MDI-PU. In MALDI-TOF MS, the weights of repeated units are 264?g/mol for TDI-PU and 340?g/mol for MDI-PU.     

MALDI-TOF/TOF CID study of 4-alkyl-substituted polystyrene fragmentation reactions

MALDI-TOF/TOF CID experiments were conducted on a variety of hydrogen-terminated poly(4-methylstyrene), hydroxylated poly(t-butylstyrene), and polystyrene precursor ions: n = 10, 15, 20, 25, and 30, where the number of repeat units n corresponds to the oligomer mass number. The influences of structure, molecular weight, and effective collision kinetic energy on degradation mechanisms were examined to test the generality of our multi-chain fragmentation model developed for polystyrene. Each depolymerization mechanism is presented in detail with experimental and computational data to justify/rationalize its occurrence and effective kinetic energy dependence. These processes show the complex interrelationship between the various pathways along with preferred production of secondary radicals, which suppresses the appearance of primary radicals. Additionally, Py-GC/MS experimental data are presented, for comparison of the multimolecular free radical reactions in pyrolysis with the unimolecular fragmentation reactions of MS/MS. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

利用Py-GC/MS研究温度和时间对生物质热解的影响

以稻壳为原料,采用Py-GC/MS装置对其在不同热解条件下进行快速热解,并对热解气进行在线检测分析,考察了热解温度和时间对生物质热解性质的影响.结果表明,低于450 ℃,随着温度的升高,生物质热解产物种类及其产率均增加,但低温条件下产物种类较少,有利于产物的分离提纯;高于450 ℃,生物质热解产物种类基本稳定,仅在产率上有所变化,当550 ℃时,收率最大.随着热解温度的升高,其对应的最佳热解时间缩短,且生物质低温热解时间延长时热解比高温解热时间缩短时热解更充分.     

Bioaccumulation study of acrylates in algae (<Emphasis Type="Italic">Chlorella kessleri</Emphasis>) by Py-GC and Py-GC/MS

Acrylate monomers methylmethacrylate (MMA) and cyclohexylmethacrylate (CHMA) bioaccumulation has been determined in aquatic organism, algae (Chlorella kessleri). Algae were collected in amount of 0.4 mg and directly injected to the pyrolytical cell. In algae bodies accumulated monomers were analysed by pyrolysis gas chromatography (Py-GC) and pyrolysis gas chromatography coupled with mass spectrometry (Py-GC/MS). Traces of the accumulated monomers in algae body can be determined after 1-, 2-, 3-weeks of incubation. Maximum content of MMA was determined after 3-week of experiment, contrariwise in the case of CHMA after 2-week exposition. Relationship with pyrolysis temperature has also been studied.     

聚亚苯基苯并二噻唑与聚亚苯基苯并二噁唑的热分解

用高分辨裂解气相色谱 质谱（ＨＲＰｙＧＣ ＭＳ）研究了聚亚苯基苯并二噻唑、聚亚苯基苯并二唑的热分解行为,鉴定了相应裂解产物的组成、分布及其与高分子结构的关系,并用热重法（ＴＧ）测定了它们的热分解反应动力学参数,提出了其热分解反应机理     

Miscibility and properties of poly(l-lactic acid)/poly(butylene terephthalate) blends

Binary blends of poly(l-lactide) (PLLA) and poly(butylene terephthalate) (PBT) containing PLLA as major component were prepared by melt mixing. The two polymers are immiscible, but display compatibility, probably due to the establishment of interactions between the functional groups of the two polyesters upon melt mixing. Electron microscopy analysis revealed that in the blends containing up to 20% of poly(butylene terephthalate), PBT particles are finely dispersed within the PLLA matrix, with a good adhesion between the phases. The PLLA/PBT 60/40 blend presents a co-continuous multi-level morphology, where PLLA domains, containing dispersed PBT units, are embedded in a PBT matrix. The varied morphology affects the mechanical properties of the material, as the 60/40 blend displays a largely enhanced resistance to elongation, compared to the blends with lower PBT content.     

Pyrolysis-GC/MS and TG/MS study of mediated laccase biodelignification of Eucalyptus globulus kraft pulp

Biobleaching studies using laccase mediator system (LMS) were carried out, under optimized conditions, on two unbleached Eucalyptus globulus kraft pulps, one produced by conventional way, with kappa number of 16.1, and another with kappa number of 14.5, obtained by modified kraft procedure with a high liquor/wood ratio and with black liquor replacement in the middle of the cooking. The pulp properties before and after LMS and alkaline extraction were evaluated in terms of kappa number, hexeneuronic acid content, viscosity, brightness and acid insoluble lignin content.The original milled wood sample and the kraft pulps were characterized by pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) and thermogravimetry/mass spectrometry (TG/MS). Eucalypt wood lignin produces guaiacol and syringol derivatives during pyrolysis. These lignin products can be detected with high sensitivity using the selected ion chromatograms even in the bleached pulp of low lignin content (about 0.5%). Py-GC/MS revealed that the lignin moieties were similarly altered during biobleaching as during pulping, which is exemplified by the preferential removal of aldehyde groups from the alkyl side groups. Semi-quantitative analysis of the pyrograms indicates that the lignin content of the biobleached pulps is reduced by about half in comparison with the unbleached pulps. The TG/MS results show that the hemicellulose content of wood was strongly modified during pulping resulting in higher thermal stability.     

生物质主要组分低温热解研究

利用热重分析仪和裂解气质联用仪进行生物质主要组分低温热解特性研究。热重实验结果表明,生物质主要组分的热稳定性为：纤维素>木质素>半纤维素。半纤维素主要热解温度在210℃～320℃,而纤维素和木质素的主要热解温度分别在310℃～390℃和200℃～550℃。裂解气质联用实验考察不同温度对生物质主要组分低温热解产物的影响。半纤维素热解产物主要有乙酸、1-羟基-丙酮和1-羟基-2-丁酮,纤维素热解产物主要包括左旋葡聚糖和脱水纤维二糖,而木质素热解产物主要是邻甲氧基苯酚。     

气相色谱-串联质谱法测定食用油中两种非邻苯二甲酸酯类增塑剂

建立了气相色谱-串联质谱同时测定食用油中对苯二甲酸二（2-乙基己基）酯和偏苯三甲酸三（2-乙基己基）酯两种非邻苯二甲酸酯类增塑剂的方法。样品采用乙腈提取,于-20℃冷冻除脂净化,用气相色谱-串联质谱选择反应监测模式测定。两种化合物的检出限为0.03 mg/kg,定量限为0.1 mg/kg,线性范围为0.1~10 mg/kg。3个添加水平（0.1、0.3和1.0 mg/kg）下的回收率为81.04%~108.31%,相对标准偏差为0.70%~9.91%。该方法简便、准确,适用于食用油中对苯二甲酸二（2-乙基己基）酯和偏苯三甲酸三（2-乙基己基）酯的检测。     

Research on pyrolysis of PCB waste with TG-FTIR and Py-GC/MS

The purpose of this study is to determine the pyrolysis characteristics and gas product properties of printed circuit board (PCB) waste. For this purpose, a combination of Thermogravimetry-Fourier Transform Infrared Spectrum (TG-FTIR) and pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) techniques is employed. In the TG-FTIR experiment, a heating rate of 10?°C min^?1 and a terminal pyrolysis temperature of 600?°C are applied. The thermal decomposition temperature, weight losses, and the temperature trend of evolving gaseous products of PCB waste are investigated. Py-GC/MS is used for the qualitative and semi-quantitative analysis of the higher-molecular-weight volatile decomposition products. Associated with the analysis results of TG-FTIR and Py-GC/MS for the volatile products, PCB waste degradation could be subdivided into three stages. The main products in the first stage (<293?°C) are H₂O, CH₄, HBr, CO₂ and CH₃COCH₃. High-molecular-weight organic species, including bromophenols, bisphenol A, p-isopropenyl phenol, phenol, etc., mainly evolve in the second stage. In the last stage, at temperature above 400?°C, carbonization and char formation occur. This fundamental study provides a basic insight of PCB waste pyrolysis.     

New approach for the kinetic analysis of cellulose using EGA-MS

This paper describes a new approach for kinetic analysis based on evolved gas analysis-mass spectrometry (EGA-MS) using pyrolyzer-gas chromatography/MS (Py-GC/MS). The kinetic results derived by this model-free kinetic analysis using the EGA-MS thermograms of cellulose were comparable to those using thermogravimetric analysis (TGA). The activation energies were in the range of 149–194 kJ/mol (mean 169 kJ/mol) for EGA/MS and 152–181 kJ/mol (mean 165 kJ/mol) for TGA. This suggests that Py-GC/MS can be used not only for the qualitative analysis of pyrolyzates, but also for the kinetic analysis of pyrolysis.     

Py-GC/MS, GC/MS and FTIR investigations on LATE Roman-Egyptian adhesives from opus sectile: New insights into ancient recipes and technologies

An analytical protocol based on optical microscopy, Fourier transforms infrared spectroscopy (FTIR), analytical pyrolysis in the presence of hexamethyldisilazane followed by gas chromatographic/mass spectrometric analysis (Py-GC/MS) and gas chromatography/mass spectrometry after alkaline hydrolysis, solvent extraction and trimethylsilylation (GC/MS) was used in the chemical characterisation of the original adhesives used to fix monochrome and mosaic glass and stone plaques coming from the Late Roman archaeological site of Antinoopolis (Egypt).FTIR analysis demonstrated the presence of calcite fragments, and Py-GC/MS and GC/MS analyses provided detailed molecular compositions, highlighting the presence of a wide range of compound classes including diterpenoid acids, tricyclic abietanes with a high degree of aromatisation, mid- and long-chain monocarboxylic fatty acids, mono- and di-hydroxy acids, α,ω-dicaboxylic fatty acids, n-alkanols, and n-alkanes. Characteristic biomarkers and their distribution patterns indicated the presence of pine pitch in all the adhesives, which in some cases was admixed with beeswax and brassicaceae seed oil.The results provided new insights into the complex recipes used by artisans in ancient Egypt in the production of adhesives and in the sophisticated manufacture of opus sectile decorations.     

Thermal degradation behaviour of aromatic poly(ester-amide) with pendant phosphorus groups investigated by pyrolysis-GC/MS

The thermal stability of a novel phosphorus-containing aromatic poly(ester-amide) ODOP-PEA was investigated by thermogravimetric analysis (TGA). The weight of ODOP-PEA fell slightly at the temperature range of 300-400 °C in the TGA analysis, and the major weight loss occurred at 500 °C. The structural identification of the volatile products resulted from the ODOP-PEA pyrolysis at different temperatures was performed by pyrolysis-gas chromatography/mass spectrometry (pyrolysis-GC/MS). The P-C bond linked between the pendant DOPO group and the polymer chain disconnected first at approximately 275 °C, indicating that it is the weakest bond in the ODOP-PEA. The P-O bond in the pendant DOPO group was stable up to 300 °C. The cleavage of the ester linkage within the polymer main chain initiated at 400 °C, and the amide bond scission occurred at greater than 400 °C. The structures of the decomposition products were used to propose the degradation processes happening during the pyrolysis of the polymer.