Characterization of the water-insoluble pyrolytic cellulose from cellulose pyrolysis oil

Water-insoluble pyrolytic cellulose with similar appearance to pyrolytic lignin was found in cellulose fast pyrolysis oil. The influence of pyrolysis temperature on pyrolytic cellulose was studied in a temperature range of 300–600 °C. The yield of the pyrolytic cellulose increased with temperature rising. The pyrolytic cellulose was characterized by various methods. The molecular weight distribution of pyrolytic cellulose was analyzed by gel permeation chromatography (GPC). Four molecular weight ranges were observed, and the M_w of the pyrolytic cellulose varied from 3.4 × 10³ to 1.93 × 10⁵ g/mol. According to the elemental analysis (EA), the pyrolytic cellulose possessed higher carbon content and lower oxygen content than cellulose. Thermogravimetric analysis (TGA) indicated that the pyrolytic cellulose underwent thermo-degradation at 127–800 °C and three mass loss peaks were observed. Detected by the pyrolysis gas chromatography–mass spectrometry (Py-GC/MS), the main pyrolysis products of the pyrolytic cellulose included saccharides, ketones, acids, furans and others. Fourier transforms infrared spectroscopy (FTIR) also demonstrated that the pyrolytic cellulose had peaks assigned to CO stretching and glycosidic bond, which agreed well with the Py-GC/MS results. The pyrolytic cellulose could be a mixture of saccharides, ketones, and their derivatives.     

New approach for the kinetic analysis of cellulose using EGA-MS

This paper describes a new approach for kinetic analysis based on evolved gas analysis-mass spectrometry (EGA-MS) using pyrolyzer-gas chromatography/MS (Py-GC/MS). The kinetic results derived by this model-free kinetic analysis using the EGA-MS thermograms of cellulose were comparable to those using thermogravimetric analysis (TGA). The activation energies were in the range of 149–194 kJ/mol (mean 169 kJ/mol) for EGA/MS and 152–181 kJ/mol (mean 165 kJ/mol) for TGA. This suggests that Py-GC/MS can be used not only for the qualitative analysis of pyrolyzates, but also for the kinetic analysis of pyrolysis.     

Thermal characteristics of bitumen pyrolysis

The pyrolysis behavior of bitumen was investigated using a thermogravimetric analyzer–mass spectrometer system (TG–MS) and a differential scanning calorimeter (DSC) as well as a pyrolysis-gas chromatograph/mass spectrometer system (Py-GC/MS). TG results showed that there were three stages of weight loss during pyrolysis—less than 110, 110–380, and 380–600 °C. Using distributed activation energy model, the average activation energy of the thermal decomposition of bitumen was calculated at 79 kJ mol⁻¹. The evolved gas from the pyrolysis showed that organic species, such as alkane and alkene fragments had a peak maximum temperature of 130 and 480 °C, respectively. Benzene, toluene, and styrene released at 100 and 420 °C. Most of the inorganic compounds, such as H₂, H₂S, COS, and SO₂, released at about 380 °C while the CO₂ had the maximum temperature peaks at 400 and 540 °C, respectively. FTIR spectra were taken of the residues of the different stages, and the results showed that the C–H bond intensity decreased dramatically at 380 °C. Py-GC/MS confirmed the composition of the evolved gas. The DSC revealed the endothermic nature of the bitumen pyrolysis.     

Synthesis,odor characteristics and thermal behaviors of pyrrole esters

A novel approach for transesterification of methyl pyrrole-carboxylate with alcohols is reported. The transformation is performed with t-BuOK and a series of new pyrrole ester were obtained under the optimized conditions. The odor characteristics of the pyrrolyl esters were evaluated by GC–MS-O (gas chromatography-mass spectrometry-olfactometry). Among them, compounds of 4-isopropylbenzyl 1H-pyrrole-2-carboxylate (3d) and naphthalen-2-ylmethyl 1H-pyrrole-2-carboxylate (3 l) present nuts and almond-like aroma, respectively. The Py-GC/MS (pyrolysis–gas chromatography/mass spectrometry) approach was applied to evaluate the pyrolysis intermediates of the pyrrole esters in oxidative conditions. It clarified that 3d and 3 l occurred different degrees of pyrolysis throughout the pyrolysis temperature from 30 °C to 900 °C. In addition, the TG (thermogravimetry) and DSC (differential scanning calorimeter) approaches were applied to investigate at the thermal degradation process. They have good thermal stability under certain temperature according to the results of TG analysis.     

Research on pyrolysis of PCB waste with TG-FTIR and Py-GC/MS

The purpose of this study is to determine the pyrolysis characteristics and gas product properties of printed circuit board (PCB) waste. For this purpose, a combination of Thermogravimetry-Fourier Transform Infrared Spectrum (TG-FTIR) and pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) techniques is employed. In the TG-FTIR experiment, a heating rate of 10?°C min^?1 and a terminal pyrolysis temperature of 600?°C are applied. The thermal decomposition temperature, weight losses, and the temperature trend of evolving gaseous products of PCB waste are investigated. Py-GC/MS is used for the qualitative and semi-quantitative analysis of the higher-molecular-weight volatile decomposition products. Associated with the analysis results of TG-FTIR and Py-GC/MS for the volatile products, PCB waste degradation could be subdivided into three stages. The main products in the first stage (<293?°C) are H₂O, CH₄, HBr, CO₂ and CH₃COCH₃. High-molecular-weight organic species, including bromophenols, bisphenol A, p-isopropenyl phenol, phenol, etc., mainly evolve in the second stage. In the last stage, at temperature above 400?°C, carbonization and char formation occur. This fundamental study provides a basic insight of PCB waste pyrolysis.     

Py-GC/MS characterization of a wild and a selected clone of Arundo donax,and of its residues after catalytic hydrothermal conversion to high added-value products

Two analytical procedures based on gas chromatography and mass spectrometry were used to study the compositions of a wild population and a selected clone (Torviscosa) of giant reed (Arundo donax L.), one of the most promising biomass both in terms of energy and fine chemicals production. Gas chromatography/mass spectrometry (GC/MS) was used to characterize and quantitatively determine the monosaccharide composition. Pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS), using hexamethyldisilazane (HMDS) as a derivatising agent, was used to characterize the lignocellulosic polymers. Analytical pyrolysis was also used to study the composition of residues left after the catalytic hydrolysis used to convert cellulose to levulinic acid and hemicellulose to furfural.GC/MS allowed us to determine the monosaccharide composition and polysaccharide content of the giant reed samples, highlighting that there was no significant difference between the wild population and the selected clone. GC/MS also highlighted that the giant reed leaves have a higher percentage (roughly 60%) of polysaccharide material than the stalks, which contain approximately 50%.Py-GC/MS, following the disappearance of the pyrolysis products of polysaccharides, showed that 150 °C and 190 °C are the best temperatures to obtain the complete catalytic conversion of hemicellulose and cellulose, respectively. Analytical pyrolysis also highlighted that in the course of catalytic hydrothermal conversion a partial depolymerisation of lignin was obtained. In particular, the formation of lignin units containing free phenol groups via the cleavage of the β-aryl ether bonds was demonstrated. The presence of these free phenols in the lignin network suggests the possible exploitation of lignin residues as antioxidant components or in high value biopolymer industries rather than the traditional use as low-value fuel for energy production.     

Investigation of the pyrolysis behaviour of brown algae before and after pre-treatment using PY-GC/MS and TGA

The pyrolysis behaviour of a number of brown macroalgae (seaweeds) collected in the UK such as Laminaria hyperborea and Fucus vesticulosus, are compared with the tropical algae Macrocystis pyrifera. Macroalgae contain a significant amount of alkali earth metals, halogens and a range of trace heavy metals. Pre-treatment of the algae has been performed to remove mineral matter in both water and weak acid. The pyrolysis behaviour of the residues has been investigated and the effect of processing on ash content and mineral composition has been determined. The pyrolysis behaviour of the raw samples and the residues from processing has been studied using thermal gravimetric analysis (TGA) and pyrolysis-GC/MS (Py-GC/MS). Total mineral matter has been determined using inductively coupled plasma-optical emission spectroscopy (ICP-OES) before and after pre-treatment. The Py-GC/MS pyrograms at 500 °C indicate the presence of a range of ketones, pentosans, nitrogen containing compounds and phenols. The residues from pre-treatment have different pyrolysis behaviours, particularly after acid treatment. The pre-treatment schemes investigated can remove a significant proportion of the mineral matter and halogens although they also selectively extract polymeric material. The residues have lower ash content and lower nitrogen content. Results for pre-treatment in water are consistent with the removal of mannitol, while results for pre-treatment in acid are consistent with the removal of fucoidan, mannitol and the partial removal of laminarin. Py-GC/MS of the residue from pre-treatment in acid produces a similar pyrogram to alginic acid in which furfural is a dominant product. There appears to be potential for the production of fuels and chemicals from brown algae by pyrolysis although the reduction of mineral matter and halogens by pre-treatment is advantageous.     

Effect of conditions on fast pyrolysis of bamboo lignin

Products derived from bamboo EMAL pyrolysis were investigated by means of pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) and the effects of temperature and catalyst (sodium chloride, permutite) on the yields of pyrolysis products were probed in detail. The results showed that thermal degradation of EMAL mainly occurred at the temperature range from 250 °C to 600 °C, and both the temperature and catalyst in EMAL pyrolysis were important factors in the formation or inhibition of products. The products that derived from p-hydroxyphenylpropanoid, guaiacylpropanoid, and syringylpropanoid of lignin units by pyrolytic reactions were classified as the heterocycle (2,3-dihydrobenzofuran), phenols, a small quantity of acetic acid and furans, etc. With an increase of pyrolysis temperature, the amount fraction of 2,3-dihydrobenzofuran (DHBF) decreased from 66.26% to 19.15%. Moreover, when the additive catalyst increased from 5% to 20%, permutite catalyst improved in the formation of DHBF from19.15% to 24.19%, whereas NaCl catalyst was effective to inhibit the production of DHBF from 19.15% to 13.08%. Permutite promoted the production of coke from EMAL pyrolysis, conversely, NaCl had an inhibiting effect on the generation of coke. And NaCl catalyst had a significant catalytic effect on raising or reducing of the product yields in bamboo lignin pyrolysis.     

Synthesis,thermal property and antifungal evaluation of pyrazine esters

Synthesis, thermal properties, as well as antifungal assessment of pyrazine esters were handed in this work. The metal-free esterification of pyrazinyl methanol and acid chloride derivatives in a stoichiometric ratio yielded the following compounds: pyrazin-2-ylmethyl benzoate (3a), (5-methylpyrazin-2-yl) methyl benzoate (3b), 1-(pyrazin-2-yl) ethyl benzoate (3c), 2-(pyrazin-2-yl) ethyl benzoate (3d), pyrazin-2-ylmethyl pivalate (3e). The spectral results totally showed that the synthesis conditions used permitted the compounds to be produced with great yield. The characterization included ¹H NMR, ¹³C NMR, IR, HRMS and organoleptic tests. Their thermal degradation process was examined by using the TG (thermogravimetry) and DSC (differential scanning calorimeter) methods. The pyrolysis products of the pyrazine esters in inert and oxidative atmospheres were analyzed by the Py-GC/MS (pyrolysis–gas chromatography/mass spectrometry) method. It revealed that 3a–3e were totally evaporated throughout the pyrolysis experiments at low temperatures. And they evaporated with high relative contents in pure nitrogen (86.12%–94.17%) and oxidative (75.01%–88.85%) atmospheres, with only a small amount decomposing into a series of substances. Additionally, the in vitro antifungal effects of compounds 3a–3e against R. solani, P. nicotianae, F. oxysporum, F. graminearum, and F. moniliforme were further investigated using the mycelial growth rate methodology. The findings shown that compound 3c has 94% and 80% inhibitor rates at 0.5 mg/ml against R. solani and P. nicotianae, respectively, with an EC₅₀ value (half maximum effective concentration) of 0.0191 mg/ml and 0.1870 mg/ml, respectively. Similarly, that of compounds 3a and 3b exhibited 82% and 91% at 0.5 mg/ml against R. solani, with an EC₅₀ value of 0.0209 mg/ml and 0.0218 mg/ml, respectively. The molecular docking of compound 3c with SDH (Succinate dehydrogenase) was preliminarily performed to reveal the binding modes in active pocket and analyze the interactions between the molecules and the protein.     

Discrimination of genetically modified poplar clones by analytical pyrolysis–gas chromatography and principal component analysis

Analytical pyrolysis combined with gas chromatography and mass spectrometry (Py-GC–MS) is a relatively rapid (1–3 h) method for the investigation of polymers. Various wood tissues from transgenic poplar clones and from control samples have been subjected to a screening test by Py-GC–MS. Pyrolysis products from lignin- and carbohydrate-derived pyrolysis products were subjected to multivariate principal component analysis (PCA). The first three PC accounting for 39–72% of the total variance in the original data set could be attributed to vinyl products from lignin and levoglucosan from cellulose. Samples with gene construct rbcs-rol C were only discriminated by plotting PC1 versus PC3 using the whole data set. However, the wood from trees containing gene construct 35 S-rol C were discriminated in all examined models indicating significant impacts during biosynthesis of the wood. One sample within the data set was further clustered because it turned out that this tree died off after two vegetation periods.     

A degradation study of waterborne polyurethane based on TDI

The thermal degradation of synthetic waterborne polyurethane (PU) based on toluenediisocyanate (TDI) was investigated by pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) and thermogravimetry (TG). The degradation profiles of cast films obtained from dispersions were evaluated. More than 20 characteristic volatile pyrolyzates reflecting the structure and pyrolysis mechanisms of the polymer have been identified by on-line MS. The synthesized products of polyurethane were pyrolyzed at 350, 450, 550, 650 and 750 °C respectively, and the analysis results revealed that the pyrolyzates distribution of the polyurethane depends strongly on the pyrolysis temperature. The aqueous polyurethane thermogravimetric measurements were used to study the kinetics of thermal degradation.     

Direct analysis of oligomeric tackifying resins in rubber compounds by automatic thermal desorption gas chromatography/mass spectrometry

Two analytical methods, automatic thermal desorption gas chromatography/mass spectrometry (ATD-GC/MS) and pyrolysis gas chromatography/mass spectrometry (Py-GC/MS), were applied as direct methods for the analysis of oligomeric tackifying resins in a vulcanized rubber. The ATD-GC/MS method, based on discontinuous volatile extraction, was found to be an effective means for direct analysis of the oligomeric tackifying resins contained in a vulcanized rubber. The oligomeric tackifying resins, such as t-octylphenolformaldehyde (TOPF) resin, rosin-modified terpene resin, and cashew resin, could be directly analyzed in vulcanized rubber by ATD-GC/MS. Much simpler total ion chromatograms were obtained by ATD-GC/MS than by flash pyrolysis with a Curie-point pyrolyzer, permitting much easier interpretation. Ions at m/z 206, 135, and 107 were fingerprints in the characteristic mass spectra obtained by ATD-GC/MS for TOPF resin in the vulcanized rubber. 1H-Indene, styrene, and isolongifolene were observed as their characteristic mass spectra in the pyrolyzate of the rosin-modified terpene resin. From the cashew resin, phenol, 3-methylphenol, and 4-(1,1,3, 3-tetramethylbutyl)phenol were obtained as the characteristic pyrolyzates by discontinuous thermal extraction via ATD-GC/MS. Copyright 1999 John Wiley & Sons, Ltd.     

Formation of a polyalkyl macromolecule from the hydrolysable component within sporopollenin during heating/pyrolysis experiments with Lycopodium spores

The most resistant component of Lycopodium spores is the macromolecule sporopollenin. The recent and fossil representatives of this material are structurally distinct and the transformations that bring about this chemical discord are poorly understood. To investigate the diagenesis of spores and their biopolymer, solvent extracted and saponified examples of Lycopodium clavatum underwent simulated diagenesis by heating (100–400 °C) under vacuum for 48 h. Following simulated maturation, spores were analysed by pyrolysis-gas chromatography–mass spectrometry (Py-GC–MS) and thermochemolysis-GC–MS. Py-GC–MS data clearly demonstrate that there is an increase in the polyalkyl hydrocarbon material in the pyrolysable component with increasing anhydrous maturation temperature. Hydrous pyrolysis of spores leads to similar changes but with an increased response from aliphatic relative to aromatic material. If the spores are hydrolysed prior to heating the generation of the polyalkyl portion of the macromolecule is markedly reduced. It appears, therefore, that the polyalkyl portion of fossil sporopollenin may be formed by maturation-induced polymerisation of the ‘labile’ hydrolysable component to form a recalcitrant polyalkyl network.     

RDF pyrolysis by TG-FTIR and Py-GC/MS and combustion in a double furnaces reactor

With the increasing depletion of fossil energy, the refuse-derived fuel (RDF) as an unavoidable by-product of human activities has been used as an alternative fuel in the precalciner cement kilns. Since the RDF combustion also brings the problems of NOx pollution, it is quite important to find ways to lower the NOx emission during RDF combustion in the precalciner. The pyrolysis characteristics and products of RDF were studied by TG-FTIR and Py-GC/MS. From TG-FITR and Py-GC/MS tests, various carboxylic acids and alkenes formed with NOx released at the RDF pyrolysis process at 200–550 °C. By simulating the temperature (700 °C, 800 °C and 900 °C) and O₂ (12%, 14%, 16%, 18% and 21%) environment of the precalciner using a double furnaces reactor, the combustion processes and NOx formation characteristics of RDF combustion were studied. The results showed that the volatile-N was the dominant reactant source of fuel NOx during RDF combustion. The fuel-N conversion and NOx emission yield showed a continuous decreasing trend with temperature increasing from 700 to 900 °C. The fuel-N conversion and NOx emission yield showed a slight increasing trend with the oxygen concentration increase, and the optimum oxygen concentration for RDF combustion was 14%. In this study, the optimum temperature was 900 °C and oxygen concentration was 14% for de-NOx in the precalciner.

     

Study on the thermal degradation of high performance fibers by TG/FTIR and Py-GC/MS

The thermal degradation behaviors of Kevlar 49, Kevlar 129 (Poly(p-phenylene terephthamide), Nomex (polyisophthaloyl metaphenylene diamine), and PBO(poly(p-phenylene benzobisoxazole)) fibers were measured by TG/FTIR and Py-GC/MS. The characteristic temperatures of the fibers in air were obtained by TG. It indicated that the initial degradation temperature of the PBO is the highest. The initial degradation temperature of Nomex fiber is the lowest, but the end decomposition temperature of Nomex is the highest. The gases released by the pyrolysis in air were mainly CO₂, CO, H₂O, NO, and HCN, also containing a small amount of NH₃, and the absorption peaks of CO₂ were the strongest. The results of Py-GC/MS showed that CO₂ and benzene were the most pyrolysis fragment. With the change of pyrolysis temperature, the chromatogram and mass spectra results take a large variety. The pyrolysates can help us to study the pyrolysis process of high performance fibers.     

Sub-critical water extraction of bitumen from Huadian oil shale lumps

Three sizes of Huadian oil shale lumps from 1 cm to 10 cm were extracted by sub-critical water at 350 °C and 16 MPa for 2–70 h. The oil shale lumps were fractured alone the shale texture in sub-critical water that greatly improved the extraction efficiency of bitumen from the large- and middle-sized sample. The extract yields of bitumen from different sized samples were similar when the extraction time is longer than 20 h and stabilized at about 18 wt.% (ad) after 50 h duration. With the increase of extraction time, asphaltene and preasphaltene extracts were gradually decomposed to maltene. The gas chromatography–mass spectrometry (GC–MS) analysis of the extracts showed that n-alkanes, n-alk-1-enes, isoprenoids, n-alk-2-ones and n-alkanoic acids were the major components. In contrast, aromatic extracts were rare and most of them were remained in the shale residue. The pyrolysis gas chromatography–mass spectrometry (Py-GC–MS) analysis of the spent shale showed that the final undecomposed organics in kerogen were some macromolecular linear hydrocarbon, n-alk-2-ones and n-alkanoic acids fragments. The comparison of the classical pyrolyzate and the sub-critical water extracts showed that the water extracts contained more long-chain alkanes than anhydrous pyrolysis and the alkene extracts could transform to alkanes in sub-critical water. Moreover, the n-alkanoic acids could be decomposed to short-chain compounds through the cleavage of carbon carbon bonds.     

Py-GC/MS, GC/MS and FTIR investigations on LATE Roman-Egyptian adhesives from opus sectile: New insights into ancient recipes and technologies

An analytical protocol based on optical microscopy, Fourier transforms infrared spectroscopy (FTIR), analytical pyrolysis in the presence of hexamethyldisilazane followed by gas chromatographic/mass spectrometric analysis (Py-GC/MS) and gas chromatography/mass spectrometry after alkaline hydrolysis, solvent extraction and trimethylsilylation (GC/MS) was used in the chemical characterisation of the original adhesives used to fix monochrome and mosaic glass and stone plaques coming from the Late Roman archaeological site of Antinoopolis (Egypt).FTIR analysis demonstrated the presence of calcite fragments, and Py-GC/MS and GC/MS analyses provided detailed molecular compositions, highlighting the presence of a wide range of compound classes including diterpenoid acids, tricyclic abietanes with a high degree of aromatisation, mid- and long-chain monocarboxylic fatty acids, mono- and di-hydroxy acids, α,ω-dicaboxylic fatty acids, n-alkanols, and n-alkanes. Characteristic biomarkers and their distribution patterns indicated the presence of pine pitch in all the adhesives, which in some cases was admixed with beeswax and brassicaceae seed oil.The results provided new insights into the complex recipes used by artisans in ancient Egypt in the production of adhesives and in the sophisticated manufacture of opus sectile decorations.     

Considering factors on determination of microstructures of SBR vulcanizates using pyrolytic analysis

Properties of styrene-butadiene rubbers (SBRs) are depending on their microstructures (contents of 1,4-unit, 1,2-unit, and styrene), but it is hard to determine the microstructures of SBR vulcanizates. Pyrolytic method such as pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) has been used for microstructures of cured rubbers without pretreatment. Microstructure of SBRs can be estimated using the major pyrolysis products (butadiene, 4-vinylcyclohexene (VCH), and styrene). In this study, considering factors for determination of microstructures of SBR vulcanizates using Py-GC/MS were investigated. The principal considering factors were found to be change of the major pyrolysis products due to radicals formed in carbon backbone and sulfur by dissociation of sulfide crosslinks in SBR vulcanizates. Relative abundances of the major pyrolysis products of raw and cured SBRs were different due to rearrangements of the radicals. Influencing factors on pyrolysis behaviors of SBR vulcanizates were found to be 1,2-unit block, alternating sequence of 1,4- and 1,2-units, styrene-1,4-unit and styrene-1,2-unit sequences, and location of the radicals. Especially, the 1,2-unit block influenced on change of the VCH/butadiene ratio, while the styrene-1,2-unit sequence affected change of the styrene/(butadiene + VCH) one.     

Discrimination of Thermoplastic Polyesters by MALDI-TOF MS and Py-GC/MS

The aim of this work is to discriminate thermoplastic polyester-polyethylene terephthalate (PET), polybutylene terephthalate (PBT), and polytrimethylene terephthalate (PTT), which cannot be easily identified by many methods. Both matrix-assisted laser desorption/ionization-time of flight mass spectrometry (MALDI-TOF MS) and pyrolysis gas chromatography/mass spectrometry (Py-GC/MS) were applied to identify these polyesters owing to their analytical ability to determining polymers' chemical structure. The three thermoplastic polyesters can be easily distinguished by MALDI-TOF MS according to their different repeated units. Py-GC/MS was used to analyze their specific pyrolyzates. The three polyesters can be identified through their characteristic pyrolysis products as well.     

In situ modification of pyrolysis products of macromolecules in an analytical pyrolyser

An application of pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) is presented for the fast on-line testing of solid catalysts activity in upgrading pyrolysis oils and/or gases of natural and synthetic polymers. Evaluation of the chemical conversion by a catalyst is simply and quickly performed in a Py-GC/MS instrument without any modification either of the micropyrolyser or the GC inlet. The pyrolysis products evolved from the sample pass through catalyst microbeds of some mm length and the GC/MS analysis of the converted products is performed on-line. Modification of polyolefin, styrene copolymer, polyester, polyamide, brominated epoxy resin and wood pyrolysate was carried out applying sodium type zeolite and medium acidic mesoporous aluminosilicate in the microbeds. The primary pyrolysis products are converted over the microbeds due to the catalytic activity of the bed material. Intramolecular hydrogen transfer reactions promoted by Na zeolite results in the isomerisation of alkenes and alkadienes evolved by pyrolysis from polyethylene and polypropylene. These basic catalysts were found to be effective for the elimination of brominated phenols from the pyrolysate of brominated epoxy resin. Cracking of alkane and alkene oligomer products of polyolefins to light isoalkenes occur over acidic mesoporous aluminosilicate. Certain compounds with polar groups evolved from polyester, polyamide, cellulose or lignin are removed by this catalyst. Alkenylaromatic compounds are simultaneously hydrogenated and polyaromatised in pyrolysis oils of styrene copolymers over both acidic and basic aluminosilicate catalysts tested.