Determination of trace inorganic selenium in organoselenium (selenosugar) oral nutrition liquids by graphite furnace atomic absorption spectrometry with hydride generation

 A method has been proposed for the determination of trace levels of inorganic selenium in organoselenium (selenosugar) oral nutrition liquids using hydride generation-graphite furnace atomic absorption spectrometry (HG-GFAAS), taking advantage of the fact that this organic selenium compound did not generate volatile hydride upon reduction. K₂S₂O₈ was selected for the decomposition of the compound in a boiling water bath. Selenium was found to give a sharp analytical signal upon reduction with NaBH₄ in 1.0 mol L^-1HCl medium. The characteristic mass giving an integrated absorbance of 0.0044 s was 21 pg. An absolute detection limit (3s) of 36 pg was obtained. The recovery was in the range of 94.2–102.1%. Less than parts per million levels of inorganic Se in the presence of organic selenium can be determined. Received: 7 November 1996/Revised: 13 January 1997/Accepted: 29 January 1997     

Evaluation of on-line coupling size exclusion chromatography electrothermal atomic absorption spectrometry for selenium speciation

 Chromatographic effluents were on-line analyzed by Zeeman-ETAAS, using a flow-through cell placed in a graphite furnace autosampler as interface. To obtain high sampling rates, the use of fast graphite furnace programmes was studied. Conventional programmes of 96 s were reduced to 18 s by using hot injection (120 °C) and reducing the charring step to 2 s. The increase of the injection volume from 20 to 60 μl lengthened the programme to 46 s. Nickel had to be added to get a comparable response for both inorganic and organic selenium species (selenite and selenomethionine) and to reduce the interferent effect produced in presence of the chromatographic eluent (TRIS 0.01 mol l^-1, NH₄NO₃ 0.1 mol l^-1, pH 7). The optimized conditions were applied to the speciation of selenium in human erythrocyte lysates by size exclusion LC-ETAAS. Using a high performance size exclusion column selenium could be assigned to proteins of 100 and 35 kDa. Detection limits in the range of 1 ng (2 μg l^-1 for 500 μl injection volume) were obtained for the combined technique. Received: 9 October 1996/Revised: 8 July 1996/Accepted: 14 July 1996     

Optimization of the reduction of Se(VI) to Se(IV) in a microwave oven

 Parameters for the reduction of Se(VI) to Se(IV) in HCl medium by heating in a microwave oven have been optimized. The reduction resulted to be quantitative applying 100% power, corresponding to 600 W heating for 2 min in 6 mol/L or for 3 min in 4 mol/L HCl. The behavior of selenomethionine and selenocystine under the optimized reduction conditions was studied in order to evaluate a possible interference of these selenium species in the determination of Se(VI). The final determination of Se(IV), and Se(VI) were done by hydride generation-atomic absorption spectrometry. The analytical merits of the method are reported. The method was applied to the selective determination of Se(IV), and Se(VI) in spiked river and lake water. Received: 6 December 1996/Revised: 1 April 1997/Accepted: 3 April 1997     

Selenium determination by HG-ICPAES: Elimination of iron interferences by means of an ion-exchange resin in a continuous flow system

 An accurate procedure for the elimination of iron interferences in the determination of selenium in geological materials by the Hydride Generation – Inductively Coupled Plasma Atomic Emission Spectrometry technique (HG-ICPAES) is proposed. A selective removal of iron is achieved by on-line incorporation of a microcolumn filled with strongly acidic cation exchange resin (Dowex 50W-X8). The microcolumn manifold used was interfaced with the hydride generation manifold by a flow injection sample injection valve. After the removal of the iron, a 500 μl sample was injected into a carrier stream of water. This was merged with hydrochloric acid and sodium tetrahydroborate in order to generate the corresponding selenium hydride. The system was found to have a limit of detection of 0.4 ng ml^-1 and a relative standard deviation of 2% for 20 ng ml^-1 selenium. The application of the method on different Geochemical Standard Reference Samples demonstrated that results were statistically indistinguishable from certified values. Received: 7 March 1996 / Revised: 30 May 1996 / Accepted: 4 June 1996     

The interface air/water of n-dodecanephosphonic acid solutions

 The air/water interface of the system n-dodecanephosphonic acid (H₂DP)–water was studied by surface tension, ion-selective electrodes and evaporation in an electrobalance. The combination of surface tension and ion-selective electrodes measurements enables to study the adsorption of soluble surfactants above the cmc using the Gibbs’ equation. H₂DP formed a nonideal monolayer at the air/water interface with A _molec=0.995 nm² below the cmc. Above the cmc there was a reduction in adsorption giving A _molec=6.32 nm², which remained almost constant in the explored concentration range. This adsorption reduction may be due to a change composition on micellization, or to a thermodynamic advantage of micellization on adsorption. The reduction in the evaporation rate of water was mainly due to the reduction of the water activity, caused by the presence of solutes in bulk. This is because the strong changes in the surface coverage did not have significant influence on the evaporation rate. Received: 6 January 1997 Accepted: 15 August 1997     

Comparison of liquid chromatography-mass spectrometry interfaces for the analysis of polar metabolites of benz[a]pyrene

 The performance of two liquid chromatography-mass spectrometry (LC/MS) interfacing techniques, thermospray (TSP) and atmospheric pressure chemical ionization (APCI), for the analysis of benzo[a]pyrene (BaP) metabolites (hydroxy, epoxy and quinone derivatives) was compared. Interface and detection parameters such as source temperature, eluent composition or flow rate were optimized using negative ion mode. In TSP, the main ions are mostly [M]^-, [M−H₂O]^- or [M+CH₃COO]^-, whereas APCI gives mainly the [M]^- and [M−H]^- ions. Quantification was carried out by flow injection. Calibration graphs were linear in the range of 10 ng to 1000 ng in TSP and 0.1 ng to 10 ng in APCI. Detection limits were in the range of 1 ng to 20 ng in TSP and 0.002 ng to 0.2 ng in APCI. The presence of BaP-1,6-dione, BaP-3,6-dione, and BaP-6,12-dione was confirmed in environmental samples of air particulate matter. Received: 6 January 1997/Accepted: 18 April 1997     

Comparison of liquid chromatography-mass spectrometry interfaces for the analysis of polar metabolites of benz[a]pyrene

 The performance of two liquid chromatography-mass spectrometry (LC/MS) interfacing techniques, thermospray (TSP) and atmospheric pressure chemical ionization (APCI), for the analysis of benzo[a]pyrene (BaP) metabolites (hydroxy, epoxy and quinone derivatives) was compared. Interface and detection parameters such as source temperature, eluent composition or flow rate were optimized using negative ion mode. In TSP, the main ions are mostly [M]^-, [M−H₂O]^- or [M+CH₃COO]^-, whereas APCI gives mainly the [M]^- and [M−H]^- ions. Quantification was carried out by flow injection. Calibration graphs were linear in the range of 10 ng to 1000 ng in TSP and 0.1 ng to 10 ng in APCI. Detection limits were in the range of 1 ng to 20 ng in TSP and 0.002 ng to 0.2 ng in APCI. The presence of BaP-1,6-dione, BaP-3,6-dione, and BaP-6,12-dione was confirmed in environmental samples of air particulate matter. Received: 6 January 1997/Accepted: 18 April 1997     

Application of rapid electrothermal atomic absorption spectrometric methods to the determination of Ag, Al, Cd and Mn in cocaine and heroin samples

 Rapid methods were developed for the direct determination of Ag, Al, Cd and Mn in cocaine and heroin by ETAAS using programmes omitting the charring step . Sample pretreatment was simple: dissolution in ultrapure water or in 35.0% (v/v) HNO₃ for heroin or cocaine, respectively. Optimum drying temperatures were 250 °C for Ag, Al and Mn, and 300 °C for Cd. The run cycles were 35 and 37 s, for Ag and Al respectively, and 36 s for Cd and Mn. The best results were obtained with Pd, Mg(NO₃)₂ and (NH₄)₂HPO₄, as chemical modifiers. The limits of detection were 8.6, 55.9, 2.2 and 12.4 μg kg^-1 for Ag, Al, Cd and Mn, respectively. Received: 14 November 1996/Revised: 14 January 1997/Accepted: 18 January 1997     

Development of an on-line UV decomposition system for direct coupling of liquid chromatography to atomic-fluorescence spectrometry for selenium speciation analysis

Speciation analysis of four selenium species (selenite, selenate, selenocystine, and selenomethionine) has been performed by on-line coupling of liquid chromatography (LC), UV decomposition, hydride generation (HG), and atomic-fluorescence spectrometry (AFS). Because only selenite (Se^IV) can generate hydrides, on-line conversion of organic and inorganic selenium species is discussed. Preliminary study showed that the use of only UV light was not sufficient to reduce selenate, because no absorption is observed for this compound at the main wavelength of the low-pressure mercury lamp (253.7 nm). Thus, new conditions based on addition of a reducing reagent (I⁻) were developed. Mechanisms of action are proposed to explain selenium species conversions. Because of their compatibility with on-line treatment, phosphate buffers were used for chromatographic separation on an anion exchange column (Hamilton PRP-X100). Detection limits (19–60 pg Se) and repeatability of the technique were close to those obtained by conventional quadrupole ICPMS. Applications to real samples such as water and oysters are presented and emphasize the robustness of the system.     

Aggregation effects on evaporation and the air/water interface of dodecyltrimethylammonium hydroxide solutions

 The system dodecyltrimethylammonium hydroxide (DTAOH)–water was studied by surface tension, ion-selective electrodes and evaporation in an electrobalance. Results confirmed earlier conclusions about a stepwise aggregation mechanism in DTAOH solutions. The aggregation process started at a total concentration C _T=(2.51±0.10)×10^-4 mol dm^-3) which probably corresponds to the formation of dimers. At C _T= (1.300±0.041)×10^-3 mol dm^-3 there was a change in the surface and evaporation behavior, corresponding to the formation of small, fully ionized aggregates which grew with increasing concentration. At C _T= (1.108±0.010)×10^-2 mol dm^-3 the formation of true micelles with hydroxide counterions in the Stern layer did not change significantly the evaporation and adsorption behavior. This means that between this concentration and C _T=(3.02±0.28)× M28.8n10^-2 mol dm^-3, the changes in structure were gradual. At the latter concentration there was a sudden change in the monolayer state at the air/water interface, with a strong surfactant desorption, and a major change in evaporation behavior. The changes are compatible with the formation of few, large aggregates reducing the total concentration of kinetically independent solute units, which in turn increased the activity of the solvent. This phenomenon is in agreement with literature information. The reduction in the evaporation rate of water was mainly due to the reduction of the water activity, caused by colligative effects. The reduction of the effective area available for evaporation had only a slight effect in water evaporation. Received: 9 January 1997 Accepted: 19 October 1997     

Dielectric behaviour of Gelatin solutions and Gels

 Sol and Gel state properties of aqueous gelatin solutions of concentrations 4%, 6%, 8% and 10% (w/v) have been investigated through dielectric relaxation studies done at various temperatures in the range T=20–60 °C carried out over a frequency range f=20 Hz–10 MHz and no relaxation of any nature was observed. The sharp transition observed at the gelation temperature T _gel provided an excellent matching with the same measured through differential scanning calorimetry (DSC). The capacitance (C _p) values above f=100 kHz became increasingly negative as the gel was melted to the sol state. However, in the gel state C _p was found to be almost independent of temperature for frequencies above 100 kHz. At frequencies lower than 10 kHz, C _p measured was ∼10⁵ F, implying pronounced interfacial polarization either due to electro-chemical reaction or because of ions getting trapped at some interface within the bulk. Received: 10 February 1997 Accepted: 2 September 1997     

Monosegmented flow-analysis of slow enzymatic reactions: Determination of triglycerides in serum

 A monosegmented flow system (MCFA) is proposed to achieve slow enzymatic spectrophotometric determinations, here applied to the determination of triglycerides in blood serum. The sample (4.5 μL), enzymatic reagent (150 μL) and an air plug (100 μL) are simultaneously inserted into a carrier stream buffered to pH 7.9 (Tris ⋅ HCl). In order to avoid the cumbersome step of air removal, a relocating detector was used. This system handles about 60 samples/h, yielding precise results (r.s.d. usually<2.5%). Sensitivity is 56 mAU ⋅ L/mmol up to 6 mmol/L triglycerides. Accuracy was assessed by running 50 samples already analysed by a conventional procedure yielding the equation C_MCFA(mmol/L)=1.00(±0.04) C_Ref(mmol/L)−0.03(±0.08); r=0.990. Received: 22 January 1997/Revised: 12 March 1997/Accepted: 28 March 1997     

Solid-phase spectrophotometric microdetermination of iron with ascorbic acid and ferrozine

 A very sensitive and selective method for the determination of trace amounts of iron has been developed, based on the reduction of Fe(III) to Fe(II) by ascorbic acid, followed by chromogenic chelation of Fe(II) with ferrozine. The complex Fe(II)-ferrozine is easily sorbed on a dextran-type anion-exchange gel packed in a 1 mm cell, and the absorbance of the gel is measured directly at 569 and 800 nm. The extended linear range of the determination is 0.5–10 ng ml^-1 of iron (apparent molar absorptivity=4.4×10⁷ l mol^-1 cm^-1) and the precision (RSD) 1.3% for a concentration of 5 ng ml^-1 of iron (n=10). The detection limit for a sample volume of 1000 ml, using 0.040 g of anion-exchanger, corresponds to 0.12 ng ml^-1. The method has been successfully applied to the determination of iron in natural and waste waters, wine, soil extract and previously digested vegetal tissues, drugs and human hair. Received: 20 November 1995/Revised: 23 January 1996/Accepted: 26 January 1996     

Study of the bioavailability of selenium in cows’ milk after a supplementation of cow feed with different forms of selenium

The purpose of the work described in this paper was to develop an easy and quick in-vitro method for comparing the bioavailability of selenium in cows’ milk after different cow feed. The study focuses on bioavailability differences resulting from the use of different selenium species (organic selenium as selenised yeast and sodium selenite) for supplementation of forage. A procedure for determination of selenium in cows’ milk and dialysates, by hydride-generation atomic-fluorescence spectrometry (HG-AFS) after microwave-assisted acid digestion, was optimised. The results show it is possible to obtain cows’ milk enriched with selenium at different concentration without altering the original composition of the milk. The bioavailability was statistically greater for cows’ milk obtained after supplementation of forage with organic selenium at levels of 0.4 and 0.5 μg Se g⁻¹ than for that obtained after supplementation with inorganic and organic selenium at levels of 0.2 and 0.3 μg Se g⁻¹.     

Determination of traces of uranium and thorium in (Ba, Sr) TiO3 ferroelectrics by inductively coupled plasma mass spectrometry

 Traces of uranium and thorium in barium(II), strontium(II) titanate ((Ba, Sr)TiO₃) ferroelectric materials were determined by inductively coupled plasma mass spectrometry (ICP-MS). Samples were completely dissolved by a mixture of 1.4% H₂O₂ and 1.0 mol⋅l^-1 HNO₃. For a complete separation of the analytes from the matrix elements, a two step separation technique involving leaching and anion-exchange was applied. By the leaching step with HNO₃ more than 90% of the matrix can be removed whereas the analytes completely remained in the solution. The anion-exchange step was carried out on a BIO⋅RAD AG1-X8 column with a mixture of 1.0 mol⋅l^-1 HF and 0.5 mol⋅l^-1 HNO₃ as eluent. The content of uranium and thorium was subsequently measured by ICP-MS. The detection limits (D.L.) obtained were 0.043 ng g^-1 and 0.035 ng g^-1 for U and Th, respectively. The reproducibility was satisfactory with a relative standard deviation of less than 3% (at the 1 ng g^-1 level, n=5). The matrix concentrations in the final solution were reduced to the sub-μg ml^-1 level which is in the range of the detection limits of USN-ICP-AES (ultrasonic nebulization-ICP-atomic emission spectroscopy). The method was successfully applied to the determination of uranium and thorium in three synthetic (Ba, Sr)TiO₃ samples spiked with the analytes at levels of 1, 5 and 10 ng g^-1 and three (Ba, Sr)TiO₃ ferroelectric samples containing sub-ng g^-1 levels of the analytes. Received: 26 February 1996/Revised: 28 May 1996/Accepted: 5 June 1996     

Determination of antimony in wine by hydride generation graphite furnace atomic absorption spectrometry

 A method was developed for the determination of Sb in wine by electrothermal atomic absorption spectrometry, based on preconcentration by hydride generation with collection directly in the graphite furnace. Thiourea was added for prereduction of Sb(V) to Sb(III). The hydride was directly generated from diluted wine. Palladium was used as modifier in the collection step; the overall efficiency of the hydride/trapping system was found to be 67%. Sb was determined in several samples of red wine; the concentrations found were in the range 0.6 to 5.7 μg/L Sb. The detection limit of the method was 39 pg Sb, corresponding to 0.13 μg/L Sb in wine when 0.3 mL wine was analyzed. Received: 3 November 1995/Revised: 22 February 1996/Accepted: 24 February 1996     

Influence of molecular weight on the microhardness of poly(ethylene terephthalate)

 Poly(ethylene terephthalate) (PET) was annealed in vacuum at different temperatures (190–260 °C) for different times (10 min–24 h) in order to examine the mechanical properties (microhardness) of PET samples with a wide range of molecular weights (10 000–120 000). Short annealing times result in a twofold decrease in mol. wt. due to hydrolytic decomposition. However, long annealing times give rise to a substantial molecular weight increase. It is found that microhardness (H) rises linearly with the degree of crystallinity obtained during up-grading of mol. wt. and its extrapolation leads to H-values of completely crystalline PET, H ^PET _c=405 MPa for samples with conventional mol. wt. and of 426 MPa for samples with mol. wt. higher than 30 000. It is shown that the increase of mol. wt. for each set of samples with a given range of degree of crystallinity also causes a slight increase of H. The influence of mol. wt. upon hardness is discussed in the light of the changes in the physical structure (crystallinity, crystal thickness) which is formed at given heat treatment conditions. Received: 29 April 1997 Accepted: 23 September 1997     

Determination of traces of uranium and thorium in (Ba, Sr) TiO3 ferroelectrics by inductively coupled plasma mass spectrometry

 Traces of uranium and thorium in barium(II), strontium(II) titanate ((Ba, Sr)TiO₃) ferroelectric materials were determined by inductively coupled plasma mass spectrometry (ICP-MS). Samples were completely dissolved by a mixture of 1.4% H₂O₂ and 1.0 mol⋅l^-1 HNO₃. For a complete separation of the analytes from the matrix elements, a two step separation technique involving leaching and anion-exchange was applied. By the leaching step with HNO₃ more than 90% of the matrix can be removed whereas the analytes completely remained in the solution. The anion-exchange step was carried out on a BIO⋅RAD AG1-X8 column with a mixture of 1.0 mol⋅l^-1 HF and 0.5 mol⋅l^-1 HNO₃ as eluent. The content of uranium and thorium was subsequently measured by ICP-MS. The detection limits (D.L.) obtained were 0.043 ng g^-1 and 0.035 ng g^-1 for U and Th, respectively. The reproducibility was satisfactory with a relative standard deviation of less than 3% (at the 1 ng g^-1 level, n=5). The matrix concentrations in the final solution were reduced to the sub-μg ml^-1 level which is in the range of the detection limits of USN-ICP-AES (ultrasonic nebulization-ICP-atomic emission spectroscopy). The method was successfully applied to the determination of uranium and thorium in three synthetic (Ba, Sr)TiO₃ samples spiked with the analytes at levels of 1, 5 and 10 ng g^-1 and three (Ba, Sr)TiO₃ ferroelectric samples containing sub-ng g^-1 levels of the analytes. Received: 26 February 1996/Revised: 28 May 1996/Accepted: 5 June 1996     

Determination of antimony in wine by hydride generation graphite furnace atomic absorption spectrometry

 A method was developed for the determination of Sb in wine by electrothermal atomic absorption spectrometry, based on preconcentration by hydride generation with collection directly in the graphite furnace. Thiourea was added for prereduction of Sb(V) to Sb(III). The hydride was directly generated from diluted wine. Palladium was used as modifier in the collection step; the overall efficiency of the hydride/trapping system was found to be 67%. Sb was determined in several samples of red wine; the concentrations found were in the range 0.6 to 5.7 μg/L Sb. The detection limit of the method was 39 pg Sb, corresponding to 0.13 μg/L Sb in wine when 0.3 mL wine was analyzed. Received: 3 November 1995/Revised: 22 February 1996/Accepted: 24 February 1996     

Determination of ultra-trace amounts of inorganic selenium species in natural water by ion chromatography-inductively coupled plasma-mass spectrometry coupled with nano-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> solid phase extraction

This work presents a nano-Al₂O₃ solid phase extraction technique for the determination of ultra-trace amounts of inorganic selenium species in aqueous systems using ion chromatography inductively coupled plasma-mass spectrometry (IC-ICP-MS). In this experiment, the inorganic selenium species were successfully extracted on a nano-Al₂O₃ solid phase column and then quantitative eluted with a 100 mmol L⁻¹ NaOH solution. Extraction conditions such as solvent identity, solvent concentration, solvent volume, solvent pH and salt addition were optimized. Under the optimum extraction conditions (elute solvent: 100 mmol L⁻¹ NaOH, solvent volume: 4 mL, pH: 7.0), low detection limits (Se (IV): 6 ng L⁻¹, Se (VI): 11 ng L⁻¹; RSD<5.0%) and good linear range (0.5–100 ng mL⁻¹, R² > 0.999) were obtained for all of the analytes. Good spiked recoveries over the range of 80–98% were obtained by applying the proposed method on real environmental water samples. These results indicated that this method is very sensitive and reliable when monitoring trace levels of inorganic selenium species in aqueous samples.