载银油茶果壳抗菌剂的制备和性能

考察银离子浓度、pH、温度、时间等制备条件对油茶果壳载银抗菌剂性能的影响,并考察了材料对大肠杆菌、金黄色葡萄球菌的抑制效果。结果表明:油茶果壳载银抗菌剂的最佳制备条件为吸附时间6 h,搅拌温度35℃,pH=4,银离子浓度是0.2 mol/L,制备的油茶果壳载银抗菌剂对大肠杆菌、金黄色葡萄球菌具有优异的抗菌性能。     

尼龙6/蒙脱土纳米复合材料非等温结晶动力学和透明性研究

将有机化的蒙脱土与尼龙6(PA6)在Haake共混机中共混,制备出尼龙6/蒙脱土纳米复合材料(PA6N);对尼龙6/蒙脱土纳米复合材料和纯尼龙6分别进行差示扫描量热法非等温结晶试验,以了解蒙脱土在尼龙6/蒙脱土纳米复合材料中的成核作用、扩大尼龙6在包装领域的应用范围.与此同时,采用偏光显微镜测定了样品的结晶形态;采用紫...     

纳米银负载的炭气凝胶制备及抗菌性能研究

以常压干燥法制备的酚醛有机气凝胶为原料,通过在硝酸银溶液中浸渍使银吸附或沉积在有机气凝胶上,在常压条件下干燥并炭化制得纳米银负载的炭气凝胶。利用扫描电镜(SEM)、透射电镜(TEM)、X-射线衍射(XRD),比表面积及孔径分析等方法研究了浸渍前后凝胶密度和结构的变化,以及制备条件对银负载炭气凝胶的载银量和凝胶结构的影响;研究了载银炭气凝胶对大肠埃氏杆菌(ATCC25922)和金黄色葡萄球菌(ATCC25923)的抗菌效果。结果表明,这类银负载炭气凝胶对大肠杆菌和金黄色葡萄球菌均有很强的杀灭能力,预期炭气凝胶在作为催化剂或吸附杀菌材料方面有良好的应用前景。     

塑料表面载银微凝胶层层组装膜的制备及抗菌活性

以载银聚烯丙基胺盐酸盐-葡聚糖微凝胶与聚苯乙烯磺酸钠为构筑基元,利用层层组装技术制备了一种可直接沉积在疏水的塑料基底表面的载银抗菌微凝胶膜. 研究结果表明,该载银抗菌微凝胶膜具有很好的抗菌能力,并且其抗菌活性可以通过控制载银微凝胶膜的组装层数方便地进行调控. 这种制备在塑料表面的载银抗菌微凝胶膜具有良好的稳定性和基底粘附力,能够保障其长效抗菌的实现.     

载银缓释型抗菌敷料

近10年来,载银缓释型抗菌敷料因其优良特性,在医药、卫生等领域引起科学家们的广泛关注。本文综述了银的抗菌机理和载银缓释型抗菌敷料的缓释机制;重点介绍了目前在国际市场上销售的代表性载银缓释型抗菌敷料的性能,并从不同的载体材料角度(如生物高分子、合成高分子、生物和合成高分子共用、有机硅材料)总结了新型载银抗菌敷料的研究进展;最后,讨论了载银抗菌医用敷料在研究和应用中需要解决的问题。     

通过柠檬酸改性提高载银活性炭的抗菌性能

通过负载柠檬酸对活性炭进行改性,用N2吸附法测定活性炭的比表面积,用AAS、SEM、XRD测试技术分析了银在活性炭上的吸附和分布,并研究了载银活性炭的抗菌性能。结果表明,负载柠檬酸使活性炭的比表面积下降约24%,但载银后活性炭的比表面积增大。柠檬酸改性为[Ag(NH3)2] 的还原吸附提供更多的活性点,使银的吸附速率加快,吸附量提高约25%,表面的银颗粒变得非常密集,粒径减小,且颗粒均匀,因此抗菌性能显著增强,其中对金黄色葡萄球菌的杀灭效果明显优于对大肠杆菌的,同时对于高分散Ag/C催化剂的制备及银的回收也具有重要的价值。     

通过柠檬酸改性提高载银活性炭的抗菌性能

通过负载柠檬酸对活性炭进行改性,用N2吸附法测定活性炭的比表面积,用AAS、SEM、XRD测试技术分析了银在活性炭上的吸附和分布,并研究了载银活性炭的抗菌性能。结果表明,负载柠檬酸使活性炭的比表面积下降约24％,但载银后活性炭的比表面积增大。柠檬酸改性为[Ag（NH3）2]^＋的还原吸附提供更多的活性点,使银的吸附速率加快,吸附量提高约25％,表面的银颗粒变得非常密集,粒径减小,且颗粒均匀,因此抗菌性能显著增强．其中对金黄色葡萄球菌的杀灭效果明显优于对大肠杆菌的,同时对于高分散Ag／C催化剂的制备及银的回收也具有重要的价值。     

Ag-TiO_2/ACF纳米复合物的制备及其对亚甲基兰光降解作用及抗菌性能

以钛酸四丁酯为前躯体,活性炭纤维(ACF)为载体,蔗醣为粘结剂,采用真空吸附水解法制备了TiO2/ACF催化剂.通过在TiO2/ACF表面负载上银纳米颗粒,制得Ag-TiO2/ACF光降解-抗菌复合材料.利用BET、XRD、SEM等方法对其进行了表征.研究了Ag-TiO2/ACF在光照下对亚甲基兰的降解作用和对大肠杆菌的杀灭效果.结果表明,光照2h,Ag-TiO2/ACF可以将溶液中亚甲基兰降解97%以上.当纳米复合材料中Ag含量为0.75wt%时,Ag-TiO2/ACF对大肠杆菌具有很强的灭杀作用.     

原位聚合玻纤-尼龙6热塑性复合材料的研究

研究了己内酰胺开环聚合反应,确定了适用于RTM方法原位制备玻纤织物增强热塑性复合材料的工艺。结果表明:表面处理可抑制玻纤对单体的阻聚作用,使单体转化率达97%,尼龙6的分子量大于3.0×105;制备的玻纤方格布增强尼龙6复合材料的力学性能比纯尼龙6有显著提高。SEM分析表明复合材料有着良好的界面连接。     

尼龙6/有机锂皂石纳米复合材料的制备及性能研究

采用十六烷基三甲基溴化铵(CTAB)对锂皂石进行有机改性,制备有机改性锂皂石(Hectorite),并通过熔融共混的方法制备了高性能、低吸水率的尼龙6(PA6)/有机化锂皂石纳米复合材料.采用X射线衍射(XRD)、能谱仪(EDS)、扫描电子显微镜(SEM)、热重分析(TGA)对改性前后的锂皂石进行了分析,结果表明有机改性后的锂皂石结构变疏松,层间距变大,其层间距由改性前的1.33 nm增加到1.76 nm,元素分析和热重分析计算锂皂石有机物的接枝量分别为0.78和0.73 mequiv/g,接枝效率分别为71.04%和66.62%,两种分析结果基本一致.采用示差扫描量热法(DSC)、透射电子显微镜(TEM)、力学性能测试研究了有机化锂皂石的用量对复合材料结晶性能、锂皂石在基体中分散性及力学性能的影响,结果表明锂皂石在PA6中没有起到成核剂的作用,复合材料的结晶度随有机锂皂石用量的增大而逐渐减小,且当锂皂石的含量为5 phr时,锂皂石主要以剥离形式分散在基体中,此时复合材料的拉伸强度和弯曲强度均达最大值,分别为81.6 MPa和122.1 MPa,较纯PA6分别增加了25.54%和23.50%,此外,锂皂石明显降低了PA6的吸水率.     

The effects of surface treated carbon fibers and CaCO<Subscript>3</Subscript> nanoparticles inclusions on the mechanical performances of PA6/ABS-based composites

The mechanical and morphological characteristics of PA6/ABS (60/40)-based hybrid composite containing HNO₃-treated short carbon fibers (HSCF) and CaCO₃ nanoparticles have been experimentally studied. A counter-rotating twin-screw extruder and an injection molding machine were employed to produce different samples containing 10 wt % of HSCF and 0, 2, 5 and 8 wt % of CaCO₃ nanoparticles. The SEM observations indicated high-quality adhesion between HNO₃-surface treated carbon fibers and PA6/ABS polymer matrix. In addition, the morphological studies showed that the inclusion of CaCO₃ nanoparticles caused a significant effect on the ABS particle dispersion in PA6/ABS matrix. The mechanical properties assessments revealed that the incorporation of 10 wt % HSCF into the PA6/ABS can significantly improve tensile strength (82%), tensile modulus (107%), flexural strength (98%), flexural modulus (104%) and impact resistance (24%). The inclusion of CaCO₃ nanoparticles, in the presence of 10 wt % HSCF, led to the noticeable improvements of tensile strength (128% for 2 wt % CaCO₃), tensile modulus (199% for 5 wt % CaCO₃), flexural strength (146% for 5 wt % CaCO₃), flexural modulus (204% for 5 wt % CaCO₃) and impact resistance (46% for 2 wt % CaCO₃). The surface treatment of carbon fibers, dispersion conditions of nanoparticles and ABS phase in polymeric matrix were found to be the major important factors affecting the mechanical properties.     

Effect of fiber length and composition on mechanical properties of carbon fiber‐reinforced polybenzoxazine

The mechanical strength and modulus of chopped carbon fiber (CF)‐reinforced polybenzoxazine composites were investigated by changing the length of CFs. Tensile, compressive, and flexural properties were investigated. The void content was found to be higher for the short fiber composites. With increase in fiber length, tensile strength increased and optimized at around 17 mm fiber length whereas compressive strength exhibited a continuous diminution. The flexural strength too increased with fiber length and optimized at around 17 mm fiber length. The increase in strength of composites with fiber length is attributed to the enhancement in effective contact area of fibers with the matrix. The experimental results showed that there was about 350% increase in flexural strength and 470% increase in tensile strength of the composites with respect to the neat polybenzoxazine, while, compressive properties were adversely affected. The composites exhibited an optimum increase of about 800% in flexural modulus and 200% in tensile modulus. Enhancing the fiber length, leads to fiber entanglement in the composites, resulted in increased plastic deformation at higher strain. Multiple branch matrix shear, debonded fibers and voids were the failures visualized in the microscopic analyses. Defibrillation has been exhibited by all composites irrespective of fiber length. Fiber debonding and breaking were associated with short fibers whereas clustering and defibrillation were the major failure modes in long fiber composites. Increasing fiber loading improved the tensile and flexural properties until 50–60 wt% of fiber whereas the compressive property consistently decreased on fiber loading. Copyright © 2008 John Wiley & Sons, Ltd.     

表面复合纳米SiO_2和碳纳米管玻璃纤维增强尼龙6的结构与性能

利用静电相互作用在玻璃纤维(GF)表面分别复合纳米二氧化硅(SiO2)和多壁碳纳米管(MWNTs),制备了GF-SiO2、GF-MWNTs复合增强体,并通过转矩流变仪制备了尼龙6(PA6)/GF-SiO2和尼龙6(PA6)/GF-MWNTs复合材料.利用扫描电子显微镜(SEM),示差扫描量热仪(DSC),热机械分析仪(DMA)等手段研究了复合材料的微观结构、热学及力学性能.结果表明,静电复合的方法可以使纳米二氧化硅(nano-SiO2)、多壁碳纳米管(MWNTs)在GF表面达到均匀吸附,复合增强体能加快尼龙6的结晶速度,并使材料的玻璃化温度、动态模量、拉伸强度、结晶温度等明显提高,其中GF-MWNTs对复合材料性能的提高最明显,拉伸强度提升了21%,模量提高了28%.     

Statistical Design of Biocarbon Reinforced Sustainable Composites from Blends of Polyphthalamide (PPA) and Polyamide 4,10 (PA410)

A full factorial design with four factors (the ratio of polyphthalamide (PPA) and polyamide 4,10 (PA410) in the polymer matrix, content percent of biocarbon (BioC), the temperature at which it was pyrolyzed and the presence of a chain extender (CE)), each factor with two levels (high and low), was carried out to optimize the mechanical properties of the resulting composites. After applying a linear model, changes in tensile strength, elongation at break and impact energy were not statistically significant within the considered material space, while the ones in the flexural modulus, the tensile modulus, density and heat deflection temperature (HDT) were. The two most influential factors were the content of BioC and its pyrolysis temperature, followed by the content of PPA. The affinity of PPA with a high-temperature biocarbon and the affinity of PA410 with a lower-temperature biocarbon, appear to explain the mechanical properties of the resulting composites. The study also revealed that the addition of CE hindered the mechanical properties. By maximizing the flexural modulus, tensile modulus and HDT, while minimizing the density, the optimal composite predicted is an 80 [PPA:PA410 (25:75)] wt% polymer composite, with 20 wt% of a BioC, pyrolyzed at a calculated 823 °C.     

The addition of clay on the mechanical properties of surface‐treated CF‐filled PA66 composites

Polyamide 66 (PA66) composites filled with clay and carbon fiber (CF) were prepared by twin‐screw extruder in order to study the influence of nanoparticle reinforcing effect on the mechanical behavior of the PA66 composites (CF/PA66). The mechanical property tests of the composites with and without clay were performed, and the fracture surface morphology was analyzed. The results show that the fracture surface area of the clay‐filled CF/PA66 composite was far smoother than that of the CF/PA66 composite, and there formed a tense interface on the CF surface after the addition of clay. The tensile and flexural strength of CF/PA66 composites with clay was improved. The impact strength decreased because of the high interfacial adhesion. In conclusion, the addition of clay favored the improvement of the higher interface strength and so had good effect on improving the tensile and flexural properties of the composites. Copyright © 2017 John Wiley & Sons, Ltd.     

Effect of ageing of sisal fibres on properties of sisal - Polypropylene composites

A composite laminate based on natural sisal fibre and polypropylene was prepared by compression moulding. The mechanical properties of the composite were assessed under tensile, flexural and impact loading. Changes in the stress-strain characteristics, yield stress, tensile strength, and tensile (Young's) modulus, due to ageing have been analysed. Important findings with the fresh and aged fibres and their behaviour in composites have been reported and analysed.     

Simultaneously improving the flame retardancy and mechanical properties for polyamide 6/aluminum diethylphosphinate composites by incorporating of 1,3,5‐triglycidyl isocyanurate

The effect of 1,3,5‐triglycidyl isocyanurate (TGIC) as a synergistic agent on the fire retardancy, thermal, and mechanical properties for polyamide 6/aluminium diethylphosphinate (PA6/AlPi) composites were investigated in detail by limiting oxygen index; vertical burning (UL‐94); cone calorimeter; thermal gravimetric analysis; rheological measurements; and the tests of tensile, flexural, and Izod impact strength. The morphologies and chemical compositions of the char residue were investigated by scanning electron microscopy, X‐ray photoelectron spectroscopy, and Fourier transform infrared spectra. The results demonstrated that AlPi and TGIC exerted an evident synergistic effect for flame retardant PA6 matrix, and the PA6/AlPi/TGIC composites with the thickness of 1.6 mm successfully passed UL‐94 V‐0 rating with the limiting oxygen index value of 30.8% when the total loading amount of AlPi/TGIC with the mass fraction of 97:3 was 11 wt%. However, the samples failed to pass the UL‐94 vertical burning tests when AlPi alone is used to flame retardant PA6 matrix with the same loading amount. The thermal gravimetric analysis data revealed that the introduction of TGIC promoted the char residue formation at high temperature. The rheological measurement demonstrated that the incorporation of TGIC improved the storage modulus, loss modulus, and complex viscosity of PA6/AlPi/TGIC composites comparing with that of neat PA6 and PA6/AlPi composites due to the coupling reaction between TGIC and the terminal groups of PA6 matrix. The morphological structures of char residues demonstrated that TGIC benefited to the formation of more homogenous and integrated char layer with no defects and holes on the surface comparing with that of PA6/AlPi composites during combustion. The higher melt viscosity of composites and the integrated and sealed char layer effectively inhibited the volatilization of flammable gas into the combustion zone and then led to the reduction of the heat release. The results of mechanical properties revealed that the incorporation of TGIC enhanced the mechanical properties for PA6/AlPi/TGIC composites comparing with that of PA6/AlPi composites with the same loading amount of flame retardant caused by the chain extension effect of TGIC. As a result, the flame retardancy and mechanical properties of PA6/AlPi composites simultaneously enhanced due to the introduction of TGIC.     

Mechanical, thermal, and moisture absorption properties of nano-clay reinforced nano-cellulose biocomposites

In this research, fully environment-friendly, sustainable and biodegradable ‘green’ composites were fabricated. A novel material comprised of microfibrillated cellulose and laponite clay with different inorganic/organic ratios (m/m) was prepared. The composites were characterized by tensile, bending and water absorption tests as well as dynamic mechanical analysis. The morphologies of these nanocomposites were evaluated through scanning electron microscopy. Results showed considerable improvement of mechanical properties; specifically in elastic modulus, tensile strength and flexural modulus with the addition of nanoclay up to 7.5 wt% nano-clay. The modulus of elasticity increased significantly by about 26 % at 5 wt% nanocaly. The flexural modulus increased by about 90 % at 7.5 wt% nanoclay. However, with an increased load of clay in the nanocomposite, the mechanical properties decreased due to the agglomeration of excessive nanoclay. The storage modulus was significantly increased at high temperature with increasing the load of nanoclay.     

Structure and properties of polyamide‐6/vermiculite nanocomposites prepared by direct melt compounding

Polyamide‐6 (PA6)/vermiculite nanocomposites were fabricated through the direct melt compounding of maleic anhydride‐modified vermiculite (MAV) with PA6 in a twin‐screw extruder followed by injection molding. The structure and morphology of the nanocomposites were determined by X‐ray diffraction and scanning and transmission electron microscopy techniques. The results revealed the formation of intercalated and exfoliated vermiculite platelets in the PA6 matrix. Tensile measurement showed that the tensile modulus and strength of the nanocomposites tended to increase with increasing vermiculite content. The thermal properties of the nanocomposites were determined by dynamic mechanical analysis, differential scanning calorimetry, and thermogravimetry measurements. The storage modulus of the PA6–MAV nanocomposites increased to almost twice that of the neat PA6. The thermal stability of the nanocomposites increased dramatically, and this was associated with the addition of vermiculite. The effect of the addition of maleic anhydride on the formation of the PA6–vermiculite nanocomposites was examined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2860–2870, 2002     

Mechanical and morphological properties of injection-molded rice husk polypropylene composites

In this work, the investigation of the physical, mechanical, and morphological properties of the rice husk flour/polypropylene composites was performed utilizing various filler loadings and coupling agent. Five levels of filler loading (35, 40, 45, 50, and 55 wt%) were designed. In addition, to help the interaction between fiber and polypropylene matrix, struktol coupling agent was added to the composites. All of tensile strength, Young's modulus, flexural strength, flexural modulus, and impact strength properties of the composites were carried out. Moreover, the 50 wt% filler-loaded composites had optimum tensile strength, flexural strength, and flexural modulus, whereas the 35 wt% of filler loading case was the best regarding Young's modulus, flexural strength, flexural modulus, and impact strength. Furthermore, the scanning electron microscope results demonstrate that as filler loading increases, more voids and fiber pullout occur.