CHARACTERIZATION OF NOVEL POLYMERIC INTERMEDIATE POLY（p-BROMOACETYL STYRENE） CROSSLINKED BY DIVINYLBEZENE

Acetyl crosslinked polystyrene (EPS) and crosslinked bromoacetyl polystyrene (BEPS)beads were synthesized by Fridel-Crafts acetylation of polystyrene (PS) and bromination of EPS respectively. FTIR, XPS, and TG-TDG were employed to characterize their structures. The results revealed there are two types of bromine in the BEPS molecule. One is in the main chain of polystyrene and the other is in the acetyl. The results of TG-DTG showed that the rates of loss weight of PS, EPS, and BEPS were 92.7%, 92.2%, and 81.3% among the 300 ℃～500 ℃; 7.3%, 7.8%, and 18. 7% in 594 ℃, 660 ℃, and 584.8 ℃, respectively.     

稳定剂KI对化学镀Ni-Fe-P-B合金性能的影响

Influences of stabilizer (KI) on the corrosion performance of the Ni-Fe-P-B deposit alloys,were investigated using electrochemical methods,weightless corrosion and heat treatment.The results show that corrosion current density (0.1585mA·cm~(-2)),porosity(0.5 No.cm~(-2)) and weightless corrosion rate of the deposit (Ni-Fe-P-B) in corrosion media are lowest,when the stabilizer (KI) concentration is 8mg.L~(-1).Corrosion resistance of the deposit drops to a different degree in the range of 200℃～600℃,and slowly falls down when CKI=8mg.L~(-1).The lattice changes and diffusion layer forming of the deposit play important roles in the changes of corrosion performance in the different range of heat treatment.However,the hardness and abradability of testing alloy increase to a different degree in 200～400℃.When CKI=8mg.L~(-1),hardness of alloy is as high as 950HV after heat treatment at 400℃×1h,which is twice that of the as-plated coating.     

Catalytic performances of kaoline and silica alumina in the thermal degradation of polypropylene

Polypropylene was cracked thermally and catalytically in the presence of kaoline and silica alumina in a semi batch reactor in the temperature range 400℃～550℃ in order to obtain suitable liquid fuels.The dependencies between process temperatures,types of catalyst,feed compositions and product yields of the obtained fuel fractions were found.It was observed that up to 450℃ thermal cracking temperature,the major product of pyrolysis was liquid oil and the major product at other higher temperatures(475℃～550℃) ...     

Structural Evolution of LLDPE-LMW/HMW Blend during Uniaxial Deformation as Revealed by In Situ Synchrotron Radiation X-ray Scattering

The structural evolutions of LLDPE-LMW/HMW blend during uniaxial deformation at temperatures of 80 and 120 ℃ were investigated by the in situ synchrotron radiation small-and wide-angle X-ray scattering(SR-SAXS/WAXS). The magic sandwich echo(MSE) sequence was used to detect a virtually dead-time-free induction decay(FID) for solid-state NMR analysis. The thermal property of the blend was first checked by DSC,and the temperature dependence of the overall crystallinity was obtained by MSE-FID. The onset melting temperature is determined to be 116 ℃(DSC), and the enhanced π-flip motions in the crystalline domains are clearly observed at T60 ℃ by MSE-FID. For deformation at 80 ℃, the lamellae become staggered in the strain-softening region as shown by the four-point SAXS pattern, whereas further deformation leads to the melting-recrystallization in the strain-hardening region. For deformation at 120 ℃, the six-point SR-SAXS signal appears just after the four-point SR-SAXS signal, which indicates the formation of new lamellae along deformation direction. In addition, no phase transition occurs in the whole deformation process at both temperatures. Current work shows the detailed temperature dependence microstructural evolution of LLDPELMW/HMW blend. This is expected to provide more structural information for correlating microscopic structure with macroscopic mechanical performance.     

SYNTHESIS AND CHARACTERISTICS OF POLY(ARYLENE ETHER DIKETONE)S

Poly(arylene ether diketone)s were prepared by the aromatic nucleophilicdisplacement reaction of 4,4'-difluorobenzil with different bisphenols in the presence of an-hydrous potassium carbonate in diphenylsulfone at elevated temperature. The polymersobtained had inherent viscosity of 0.51 ～ 0.63 dL/g, and exhibited glass transition temper-ature ranging from 136 ～217℃ mainly depending on the bisphenols used in the polymersynthesis. Thermogravimetry of these polymers showed excellent thermal stability, indi-cating that 10% weight losses of the polymers were observed in the range above 428℃ and438℃ in air and nitrogen, respectively. The mechanical properties of these polymers werealso described and the permeability of five polymers for H_2, O_2 and N_2 was determined at30℃.     

Thermal transformation of acid compounds in high TAN crude oil

The Liaohe crude oil with high total acid number (TAN) was subjected to thermal reaction at 300℃to 500℃. Reaction products were collected and analyzed by negative-ion electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI FT-ICR MS) to determine acid compounds in the crude oil. The double-bond equivalence (DBE) versus carbon number was used to characterize the oxygenated components in the feed and reaction products. The O2 class which mainly corresponds to naphthenic acids decarboxylated at 350-400℃, resulting in a sharply decrease in TAN. Phenols (O1 class) are more thermally stable than carboxylic acids. Carboxylic acids were also thermally cracked into smaller molecular size acids, evidenced by the presence of acetic acid, propanoic acid, and butyric acid in the liquid product. These small acid species are strong acids likely responsible for corrosion problems in refineries.     

PROPERTIES OF SILK FIBROIN/POLY(ETHYLENE GLYCOL)400 BLEND FILMS

The blend film of silk fibroin (SF) and poly(ethylene glycol)400 (PEG400) with a blend ratio of 2/1 (wt/wt) wasprepared simply by dropping a little PEG400 into the SF solution and then casting the mixed aqueous solution at 50℃. Theresulting film exhibited much better mechanical properties in the dry and wet state than SF itself, owing to theconformational change of SF in the blends from the random coil to the β-sheet structure and intermolecular hydrogen bondformation between SF and PEG400. Thermogravimetric analysis showed that the initial thermal decomposition temperatureof the blend film was 170℃, which was 80℃ lower than that of SF (250℃) and 20℃ higher than that of PEG400 (150℃),and indicated a Strong interaction between two components of the blend. No crystalline peaks were observed in the X-raydiffraction curve of the blend film. Cell culture test showed that SF/PEG400 was a suitable substrate for the growth of humanumbilical vein endothelial cells (HUVEC).     

Cationic polymerization of isobutylene coinitiated by AlCl3 in the presence of ethyl benzoate

<正>The cationic polymerizations of isobutylene(IB) coinitiated by AlCl_3 were carried out in solvent mixture of n-hexane /methylene dichloride(n-hex/CH_2Cl_2) of 60/40 V/V in the presence of ethyl benzoate(EB) at various temperatures range from-80℃to-30℃.The effects of EB concentration([EB]) and polymerization temperature on monomer conversion,weight-average molecular weight(M_w) and molecular weight distribution(MWD,M_w/M_n) of polyisobutylene (PIB) products were investigated.The rate of polymerization decreased while M_w of PIB products increased with increasing [EB].The polymers with high molecular weight could be prepared in the presence of a suitable amount of EB.Significantly, the polymers with high M_w of 80.2×10~4 and 65.4×10~4 could be produced at-80℃and-70℃at[EB]=0.24×10~(-3) mol/L respectively,which were much higher than that(M_w=57.9×10~4) of PIB prepared at-100℃in the absence of EB.A simple but effective method for preparing the high molecular weight polyisobutylenes was developed in this work.It has been also found that the activation energy for propagation(E_p) depended on the polymerization temperature range in the presence of EB.An obvious inflection of the linear plots of lnX_n versus 1/T_p occurred at the temperature range from-60℃to-50℃at four different concentrations of EB from 0.19×10~(-3) mol/L to 0.33×10~(-3) mol/L,and thus the inflection temperature(T_(inf)) was in the range of-60℃to-50℃.When[EB]was in the range of 0.24×10~(-3) mol/L to 0.33×10~(-3) mol/L,E_p was determined to be around-12 kJ/mol when the polymerization was carried out at temperatures from-80℃to T_(inf) and to be around-28 kJ/mol at temperatures from T_(inf) to-15℃respectively.     

HYDROBORATION OF ALKYNES WITH DICHLOROBORANE-DIMETHYL SULFIDE——SYNTHESES AND SPECTROSCOPIC CHARACTERISTICS OF gem-DIBORON AND ALKENYLBORON COMPOUNDS

The reactions of alkynes with dichloroborane-dimethyl sulfide (HBCl_2·SMe_2) in the presence of boron trichtoride in pentane have been investigated.Both internal and terminal alkynes react with HBCl_2·SMe_2 in the molar ratio 1:2 at 0℃ to give dihydroborating products, gem-bis (dichloroboryl)alkanes, in good yield. Since the dihydroboration of alkynes is suppressed considerably at lower temperature, the internal alkynes and HBCl_2·SMe_2 react quantitatively in the molar ratio 1.4:1 at-20℃ or -30℃ to give the expected alkenyldichloroboranes.Under the same conditions,the terminal alkynes, however, undergo both monohydroboration and chloroboration.When terminal alkynes react with boron trichloride in the molar ratio 1 :1.1 in pentane, the chloroborating products, 2-chloro-1-alkenyldichloroboranes have been obtained in high yield.All dichloroboranes are readily converted by alcoholysis into the corresponding boronic esters.The resulting compounds have been characterized by IR, ~1H,~(11)B, and ~(13)C N     

Synthesis and characterization of organosoluble polyamides from quinoxaline based diamine

<正>Aromatic/aliphatic polyamides were synthesized from a diamine monomer,2,3-bis-p-aminophenylquinoxaline (Ⅳ),based on quinoxaline and various dicarboxylic acids of aliphatic,aromatic and heterocyclic.The diamine and polyamides were characterized by elemental analysis,FTIR and ~1H-NMR.The solubility of the polyamides was affected by the quinoxaline and heterocyclic groups in the polymer chain.They were all soluble in common organic solvents such as dimethylsulfoxide(DMSO),N,N-dimethylformamide(DMF) and N-methylpyrolidone(NMP).The polyamides showed inherent viscosity in the range of 0.25-0.3 dL/g in DMSO at 25℃and good thermal stability with the char yields in the range of 65%-82%at 600℃in nitrogen.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.