离子液体对木瓜蛋白酶催化特性的影响

研究了以1-丁基-3-甲基咪唑、四乙基铵及N-乙基吡啶为阳离子, 配以多种阴离子(H₂PO₄^-, ClO₄^-, HSO₄^-, CH₃COO^-, Cl^-, Br^-, NO₃^-, SCN^-, BF₄^-, PF₆^-)的离子液体对木瓜蛋白酶催化N-苯甲酰-L-精氨酸乙酯(BAEE)水解的活性及热稳定性的影响. 通过分析含离子液体体系中木瓜蛋白酶的水解活性和热力学失活参数, 发现该酶活性及稳定性与离子液体的Kosmotropicity性质无关. 因此, 离子的Hofmeister效应并不适合解释离子液体对木瓜蛋白酶催化特性的影响规律. 当以BF₄^-为阴离子, 改变阳离子结构时, 仅[BMIm][BF₄]可提高酶活性, 其它含官能团的咪唑类离子液体则降低酶活性, 但大部分离子液体明显提高木瓜蛋白酶的热稳定性. 在所研究的离子液体中, 基于PF₆^-或BF₄^-阴离子的离子液体可提高木瓜蛋白酶的活性及其热稳定性. 在含[BMIm][PF₆]介质中, 木瓜蛋白酶的水解活性最高; 在含[HOEtMIm][BF₄]介质中其热稳定性最好.     

离子液体电解质种类对活性炭电极超级电容器电化学性能的影响

本文将经水蒸气二次活化的椰壳活性炭（W-AC）作为电极材料,选择1-乙基-3甲基咪唑四氟硼酸盐（[EMIM]BF₄）作为电解质,结果表明W-AC电极的比电容量远高于未活化的椰壳活性炭（R-AC）.使用循环伏安、恒电流充放电、交流阻抗等方法研究了不同种类离子液体电解质对超级电容器电化学性能的影响.不同阴阳离子组成的离子液体作为电解质,直接影响超级电容器的电化学性能. 研究表明,由EMIM⁺和BMIM⁺阳离子与BF₄^-、TFSI^-阴离子构成的离子液体电解质较适用于W-AC电极. 其中在[EMIM]BF₄电解质中,单片电极的比电容量可高达153 F·g^-1;在1-丁基-3-甲基-咪唑四氟硼酸盐（[BMIM]BF₄）电解质中电位窗可达3.5V,能量密度可高达57 Wh·kg^-1.本研究对于构筑高性能超级电容器离子液体的选择提供参考,以满足不同应用领域需求.     

Au@SiO2膜/Ti电极吸附吡啶的表面增强拉曼光谱研究

基于壳层隔绝纳米粒子增强拉曼光谱技术,合成了Au@SiO₂纳米粒子,并对其进行了相关表征. 结果表明,包裹的二氧化硅层连续、致密,Au@SiO₂膜/Ti电极上可获得金属钛电极上吸附吡啶分子的高质量表面增强拉曼光谱（SERS）信号. 通过Pt、Ni电极的测试,证实该信号源于吸附在基底表面的吡啶分子. 此外,Au@SiO₂膜/Ti电极上吸附吡啶分子的现场SERS光谱研究表明,在-0.1 V ~ -0.6 V电位区间,吡啶分子平躺吸附,从-0.6 V起吸附的吡啶分子由平躺逐转变为垂直,而当电位为-1.2 V时,电极表面析氢,吡啶脱附.     

离子液体型表面活性剂研究

以1-甲基咪唑为原料, 制备了6个常规离子液体: 1-正丁基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[bmim][BF₄]及[bmim][PF₆])、1-正己基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[hmim][BF₄]及[hmim][PF₆])、1-正十六烷基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[C₁₆mim][BF₄]及[C₁₆mim][PF₆])和4个功能化离子液体: 1-(2-羟乙基)-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[2-hemim][BF₄]及[2-hemim][PF₆])、1-乙氧羰基甲基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[eocmmim][BF₄]及[eocmmim][PF₆]). 研究了这两类离子液体的一些物理性能, 旨在挖掘离子液体在香料香精化妆品工业中的应用价值. 分别检测了它们与一般溶剂的互溶性, 并测定了它们的表面张力和发泡性能, 实验结果表明, 仅[C₁₆mim][BF₄]和[C₁₆mim][PF₆]具有发泡性能, 发泡力分别为68和120 mm.     

离子液体中硫氰根在铂电极上吸附行为的SERS研究

利用表面增强拉曼光谱(SERS)研究了室温离子液体1-丁基-3-甲基咪唑氟硼酸盐([BMIM]BF4)中SCN-在Pt电极表面的吸附行为. 研究结果表明, 离子液体中SCN-在较宽的电位范围内吸附在Pt电极上, 且SCN-的吸附方式随着电位区间的变化而变化, 在不同的电位区间内检测到了不同的Stark位移: -0.9~0.4 V约为34 cm-1/V, 对应于S端吸附; -1.6~-1.2 V约为40 cm-1/V, 该区间以N端吸附为主, 中间电位区间为吸附方式的转变区, 且Pt电极在离子液体[BMIM]BF4中的零电荷电位约为-1.1 V(vs. Pt ).     

离子液体中铜纳米粒子膜的电沉积制备及表面增强拉曼光谱

采用恒电位方法研究了室温离子液体1-丁基-3-甲基咪唑氟硼酸盐([BMIM]BF₄)中氧化铟锡(ITO)电极表面Cu的沉积过程. 结果表明, Cu²⁺在ITO表面经中间产物Cu⁺还原为Cu. 采用XRD和SEM对不同电位下沉积层的组成和结构进行了考察. 结果表明, 表面组成和结构与沉积电位有关. 在较正电位下沉积所得为Cu/Cu₂O的混合纳米粒子; 在较负电位下为Cu纳米粒子. 随着沉积电位逐渐变负, 其形貌经历了花状、 棒状向球形纳米粒子转变的过程, 且所得沉积膜逐渐变得致密, 其中Cu纳米粒子膜表现出较强的表面增强拉曼散射(SERS)活性, 并且SERS信号均一.     

含水离子液体/金属界面结构的SERS研究

利用表面增强拉曼光谱(SERS)研究了不同含水量下离子液体及水分子在银电极上随电位变化吸附方式的改变,通过水的O-H伸缩振动谱峰频率变化特征,详细探究了水在离子液体/电极界面上的存在形式及作用方式以及体系零电荷电位与水含量的关系.水含量较低时O-H伸缩振动的Stark系数值较低,随水含量的增加O-H伸缩振动的谱峰位置逐渐向高波数方向移动,同时O-H伸缩振动的Stark系数也逐渐增大,1molL-1[BMIM]Br水溶液中达到76cm-1V-1,且体系的零电荷电位正移,这些差异与水在离子液体中所形成氢键的程度及水分子的存在形式密切相关,在水的含量较低时水与离子液体阳离子通过氢键作用而存在于界面层中,当水的含量增加时,水分子间氢键的作用增强,水与电极表面直接作用的可能性增大.     

室温离子液体对氨基苯磺酸的萃取性能

系统研究了[C₄mim][PF₆], [C₆mim][PF₆], [C₆mim][BF₄]和[C₈mim][BF₄]室温离子液体对间氨基苯磺酸、对氨基苯磺酸稀水溶液的萃取平衡. 实验结果表明: 萃取温度和相体积比的变化对分配比影响不大; 水相pH值对萃取平衡有较大的影响, 氨基苯磺酸在离子液体/水体系中的分配比在pH＝4.2时达到最大值; 水相中CaCl₂或Na₂SO₄的存在能较大幅度地提高氨基苯磺酸的分配比; 离子液体的阴离子的性质对分配比有显著的影响, 阴离子为[BF₄]^－的离子液体对氨基苯磺酸的萃取能力大于阴离子为[PF₆]^－的离子液体; 咪唑环上烷基链的长度也对萃取效果有一定的影响. 在所研究的离子液体中, [C₆mim][BF₄]和[C₈mim][BF₄]对氨基苯磺酸有较好的萃取性能, 且萃取相中的氨基苯磺酸可回收利用, 离子液体也可循环使用.     

1-烷基-3-甲基咪唑系列室温离子液体表面张力的研究

合成了系列1-烷基-3-甲基咪唑四氟硼酸盐([C_2～7mim]BF₄)及六氟磷酸盐([C_4～7mim]PF₆)室温离子液体, 并通过核磁氢谱、红外光谱、质谱等手段对其进行了结构表征; 采用Wilhelmy白金板法, 在293～338 K范围内测定了离子液体的表面张力, 测试结果显示, 同类离子液体表面张力γ随温度的升高而线性下降, 同种离子液体的表面张力呈现出较宽的变化范围, 如293 K下, 表面张力值从[C₂mim]BF₄的50.4 mJ/m²到[C₇mim]BF₄的36.1 mJ/m². 最后对离子液体的表面性能进行了讨论.     

反气相色谱法表征离子液体1-己基-3-甲基咪唑四氟硼酸盐的热力学参数

采用反气相色谱法(IGC)表征了离子液体(IL)1-己基-3-甲基咪唑四氟硼酸盐([HMIM]BF₄)在343.15~373.15 K温度范围内的热力学参数.使用了一系列不同化学结构的探针分子测定[HMIM]BF₄与溶剂之间的相互作用力.根据探针分子的保留时间计算得到探针分子与[HMIM]BF₄之间的Flory-Huggins相互作用参数、摩尔吸附焓、无限稀释摩尔混合焓、摩尔蒸发焓、无限稀释活度系数以及[HMIM]BF₄的溶解度参数.结果表明,n-C₆、n-C₇、n-C₈、n-C₉、乙醚、四氢呋喃、苯、环己烷为[HMIM]BF₄的不良溶剂;甲苯、间二甲苯、甲醇、乙醇、二氯甲烷、四氯化碳、氯仿、丙酮、乙酸乙酯、乙酸甲酯为[HMIM]BF₄的良溶剂.运用外推法得到了[HMIM]BF₄在室温(298.15K)时的溶解度参数为23.70 (J·^-3)^0.5.实验结果证明反气相色谱法是一种简便准确的获得离子液体热力学参数的方法.获得的热力学参数体现了这种离子液体与探针分子之间的相互作用力.本研究为离子液体的进一步应用提供了参考.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.