毛细管电泳法测定银杏叶片中的橙皮素、芦丁和槲皮素

建立了一种利用毛细管电泳法测定银杏叶片中橙皮素、芦丁和槲皮素的方法.研究了缓冲溶液pH和浓度、分离电压和进样时间对分离的影响,在优化的条件下,10 min内实现了三种物质的良好分离.橙皮素、芦丁和槲皮素分别在0.03～0.80、0.06～1.00,0.04～0.90 mg/mL浓度范围内和峰电流成线性关系,线性相关系数分别为0.9992、0.9976和0.999l,检出限分别为0.005、0.009和0.006 mg/mL.     

反相高效液相法测定枳实、枳壳中橙皮甙和柚皮甙的含量

 采用高效液相法测定了枳实和枳壳中的橙皮甙和柚皮甙含量。柱为HypersilODS1柱(250mm×4 6mmi d ),流动相为乙腈 0 5%乙酸溶液(体积比为22∶78),流速为1 0mL/min,检测波长为283nm。柚皮甙和橙皮甙的线性范围分别为0 060g/L～0 604g/L和0 0125g/L～0 125g/L,柚皮甙和橙皮甙的平均回收率分别为97 1%和95 3%。该方法具有操作简便、分析快速、准确等优点。     

毛细管电泳法测定密蒙花中的橙皮素、木犀草素和芹菜素

建立了毛细管电泳法分析密蒙花中橙皮素、木犀草素和芹菜素的方法,研究了缓冲溶液pH和浓度、工作电压和进样时间以及β CD的影响。在优化的条件下,3种物质在15min内得到良好分离。橙皮素、木犀草素和芹菜素的质量浓度分别在0.01～0.50mg mL、0.02～0.70mg mL、0.04～0.80mg mL范围内与峰高成良好线性,线性相关系数分别为0.9992、0.9994和0.9984。3种物质基于迁移时间和峰高的相对标准偏差分别为1 3%、2 2%、2 6%和4 2%、3 7%、4 6%。检出限分别为3 5、4 5和5 0μg mL。     

反相高效液相色谱法同时测定柚皮中柚皮甙和橙皮甙的含量

采用反相高效液相色谱法同时测定柚皮中柚皮甙和橙皮甙的含量。色谱条件:μ-BondapakC18柱(250mm×4.6mm,5μm),流动相为甲醇-0.5%乙酸溶液(V/V=38/62);流速为0.8mL·min-1;检测波长为283nm,柱温为25℃。柚皮甙和橙皮甙的线性范围分别为20-60mg·L-1和10-30mg·L-1。柚皮甙和橙皮甙的平均回收率分别为99.3%和97.8%。该方法具有快速,结果准确等优点。     

毛细管电泳电化学检测法测定中药枳实和枳壳中的辛弗林和3种黄酮

采用毛细管电泳电化学检测法同时测定了枳实和枳壳中的辛弗林和3种黄酮即橙皮甙、柚皮素和柚皮甙的含量。考察了工作电极的氧化电位、分离电压和进样时间,运行缓冲的浓度和pH值对分离和检测的影响。在优化条件下,以300μm直径的碳圆盘电极为检测电极,检测电位为 0.85 V(vs.SCE),在80 mmol/L硼酸盐(pH 8.45)的运行缓冲液中,被测物浓度与峰电流在3个数量级范围内呈良好线性,检出限(S/N=3)在1×10-4~5×10-4g/L之间,该法简单、可靠、快速,单次测定可在20 m in内完成,已经成功应用于实际样品枳实和枳壳中4组分的测定,样品处理简单,无须预富集,检测结果令人满意。     

β-环糊精修饰区带毛细管电泳法快速测定染料木甙、染料木素、山柰酚和芦丁

通过研究缓冲溶液的pH和浓度、β-环糊精浓度、十二烷基硫酸钠浓度和毛细管温度等条件,建立了一种β-环糊精修饰区带毛细管电泳法快速测定染料木甙、染料木素、山柰酚和芦丁的方法。在优化的条件下,4种物质在6 min内得到良好分离。染料木甙、染料木素、山柰酚和芦丁峰面积和质量浓度分别在2~400,2~300,2~200和5~500 mg.L-1范围内呈线性关系。染料木甙、染料木素、山柰酚和芦丁的检出限分别为0.8,0.6,0.6和1.4 mg.L-1。方法用于分析生槐角和炙槐角样品并做加标回收试验,回收率结果在93.8%~105.2%。     

非水毛细管电泳-化学发光法测定食品包装材料中酚类环境激素

建立食用包装材料中的双酚A、壬基酚等多种环境激素的非水毛细管电泳-化学发光分析方法.食品包装材料样品浸出物中的双酚A、烷基酚等环境激素经衍生剂DIB-Cl衍生后,经过非水毛细管电泳分离后,分别与过氧草酸酯化学发光反应体系作用,光信号经过光电倍增管接收放大后被检测.以雌二醇(17β-E2)为内标,以相对迁移时间定性,相对发光强度比定量,内标校准曲线法测定样品浸出物中待测物的含量.对影响非水毛细管电泳分离如溶剂组成和比例、电解质浓度、温度、乙酸浓度、电泳电压等条件进行了优化.同时对化学发光体系也进行了优化.4-叔丁基酚、双酚A、4-叔辛基酚、4-壬基酚和四溴双酚 A分别在0.0095～3.0 mg/L, 0.0087～3.0 mg/L, 0.0085～3.0 mg/L, 0.011～3.0 mg/L和0.009～3.0 mg/L范围内线性良好,r＞0.9947.相对迁移时间和相对峰高的RSD分别为0.88%～2.96%和 6.54%～8.57%.加标回收率为86.7%～98.8%.对5种常见的食品包装材料样品进行了测定, 所建立的方法简便、快速、灵敏,适合于食品包装材料中酚类环境激素的检测.     

柚皮甙的电化学研究

用单扫示波极谱法，柚皮甙在０．１ｍｏｌ／ＬＫＨ２ＰＯ４中（ｐＨ＝４．６０）有一灵敏的二阶导数峰，峰电位为－１．４３Ｖ（ｖｓ．ＳＣＥ），峰电流与浓度在０．１～２．８ｍｇ／Ｌ和３．０～４２ｍｇ／Ｌ范围内有良好线性关系，检出限为０．０６ｍｇ／Ｌ．应用本法测定了生药枳壳中总黄酮含量，结果令人满意．实验证明柚皮甙的电极反应机理为双电子不可逆过程．此外，还证明了Ｈ２Ｏ２和·ＯＨ自由基可催化该还原峰，讨论了柚皮甙对超氧自由基Ｏ·－２的清除作用．     

β-环糊精修饰区带毛细管电泳法测定野菊花中刺槐素、木犀草素和槲皮素

通过研究缓冲溶液pH和浓度、工作电压、SDS浓度和-βCD浓度等条件,建立了β-环糊精修饰区带毛细管电泳法测定野菊花中刺槐素、木犀草素和槲皮素的方法。在优化的条件下,3种物质在8min内得到良好分离。刺槐素、木犀草素和槲皮素峰面积和质量浓度分别在2~400,2~500和2~500mg.L-1范围内呈良好线性,检出限分别为0.6,0.5和0.6mg.L-1。该方法被用于分析实际样品并得到满意的结果。     

芦丁、金丝桃甙、槲皮甙和异槲皮甙的毛细管电泳分离及测定

提出了一种利用毛细管电泳法分离并测定芦丁、金丝桃甙、槲皮甙和异槲皮甙的方法.研究了缓冲溶液pH和浓度、分离电压和进样时间对分离的影响,在优化的条件下,20 min内实现了4种物质的良好分离.方法用于分析模拟样品,得到令人满意的结果,有望用于实际样品分析.     

Organogermyl,Organostannyl, and Organoplumbyl Phosphines,Arsines, Stibines,and Bismuthines

The preparation, properties, and reactions of the compounds named in the title are described, with particular reference to the possible participation of (p→d)_π components in the bonding between the group IVB and the group VB elements.     

Pi bonding and negative hyperconjugation in mono-, di-, and triaminoborane, -alane, -gallane, and -indane

A systematic quantum chemical investigation of mono-, di-, and triaminoborane, -alane, -gallane, and -indane is carried out to determine quantitatively the effects of pi bonding and negative hyperconjugation on structures, energetics, and rotational barriers in these systems. Pi bonding plays a significant role in the aminoborane compounds, but becomes rapidly less significant in the aminoalanes, -gallanes, and -indanes. For each main-group metal X investigated, X-N rotational barriers are found to be essentially equal depending only on the number of remaining in-plane amino groups. The contribution of negative hyperconjugation to reducing rotational barriers, as assessed from natural bond orbital (NBO) delocalization energies, is independent of the pyramidalization of the out-of-plane amino group, and is also dependent only on the number of rotated groups. Optimized tris[bis(trimethylsilyl)amino]-substituted structures of boron, aluminum, gallium, and indium are found to compare quite well with available experimental structural data, and exhibit X-N torsion angles that are independent of the central metal atom.     

Transition-metal-free O-, S-, and N-arylation of alcohols, thiols, amides, amines, and related heterocycles

A new protocol for the Ullmann-type arylation process of different aromatic heterocycles without any transition-metal catalyst, implying the use of a combination of an excess of potassium hydroxide and dimethyl sulfoxide, is described. The reaction can be performed between a broad range of starting nucleophiles including phenol, alcohols, amines, nitrogen-containing five-membered systems such as pyrazoles, imidazoles, and indoles, and amides with haloarenes, iodide and bromide derivatives giving the best results, the possible pathway involving the in situ generation of the corresponding benzyne intermediate. When the reaction was performed with 2-iodoaniline and either carboxamides or isothiocyanato derivatives, the corresponding benzoazole derivatives were obtained.     

Pyrenes,Peropyrenes, and Teropyrenes: Synthesis,Structures, and Photophysical Properties

The design of a relatively simple and efficient method to extend the π‐conjugation of readily available aromatics in one‐dimension is of significant value. In this paper, pyrenes, peropyrenes, and teropyrenes were synthesized through a double or quadruple benzannulation reaction of alkynes promoted by Brønsted acid. This novel method does not involve cyclodehydrogenation (oxidative aryl–aryl coupling) to arrive at the newly incorporated large arene moieties. All of the target compounds were synthesized in moderate to good yields and were fully characterized with the structures unambiguously confirmed by X‐ray crystallography. As expected, photophysical characterization clearly shows increasing red‐shifts as a function of extended conjugation within the fused ring systems.     

Borinium, borenium, and boronium ions: synthesis, reactivity, and applications

Boron cations are elusive and highly electrophilic species that play a key role in the chemistry of boron. Despite early interest in the chemistry of boron cations, until recently they have largely remained chemical curiosities. However, hints at harnessing their potential as potent electrophiles have begun to appear and developments in weakly coordinating anion technology suggest that this is an area of research that is ripe for exploration. It has been nearly 20 years since the last major review on boron cations; herein we summarize the progress in the area since that time.     

Pyrenes,Peropyrenes, and Teropyrenes: Synthesis,Structures, and Photophysical Properties

The design of a relatively simple and efficient method to extend the π‐conjugation of readily available aromatics in one‐dimension is of significant value. In this paper, pyrenes, peropyrenes, and teropyrenes were synthesized through a double or quadruple benzannulation reaction of alkynes promoted by Brønsted acid. This novel method does not involve cyclodehydrogenation (oxidative aryl–aryl coupling) to arrive at the newly incorporated large arene moieties. All of the target compounds were synthesized in moderate to good yields and were fully characterized with the structures unambiguously confirmed by X‐ray crystallography. As expected, photophysical characterization clearly shows increasing red‐shifts as a function of extended conjugation within the fused ring systems.     

Structural, magnetic, and spectroscopic studies of YAgSn, TmAgSn, and LuAgSn

The rare earth-silver-stannides YAgSn, TmAgSn, and LuAgSn were synthesized from the elements by arc-melting and subsequent annealing. The three stannides were investigated by X-ray powder and single-crystal diffraction: NdPtSb type, P6₃mc, Z=2, a=468.3(1), pm, wR₂=0.0343, 353 F² values, 12 variables for YAgSn, and ZrNiAl type, P6¯2 m, a=726.4(2), , wR₂=0.0399, 659 F² values, 15 variables for TmAgSn, and a=723.8(2), , wR₂=0.0674, 364 F² values, 15 variables for LuAgSn. Besides conventional laboratory X-ray data with monochromatized Mo radiation, the structures were also refined on the basis of synchrotron data with , in order to clarify the silver-tin ordering more precisely. YAgSn has puckered, two-dimensional [AgSn] networks with Ag-Sn distances of 278 pm, while the [AgSn] networks of TmAgSn and LuAgSn are three-dimensional with Ag-Sn distances of 279 and 284 pm for LuAgSn. Susceptibility measurements indicate Pauli paramagnetism for YAgSn and LuAgSn. TmAgSn is a Curie-Weiss paramagnet with an experimental magnetic moment of 7.2 μ_B/Tm. No magnetic ordering is evident down to 2 K. The local environments of the tin sites in these compounds were characterized by ¹¹⁹Sn Mössbauer spectroscopy and solid-state NMR (in YAgSn and LuAgSn), confirming the tin site multiplicities proposed from the structure solutions and the absence of Sn/Ag site disordering. Mössbauer quadrupolar splittings were found in good agreement with calculated electric field gradients predicted quantum chemically by the WIEN2k code. Furthermore, an excellent correlation was found between experimental ¹¹⁹Sn nuclear magnetic shielding anisotropies (determined via MAS-NMR) and calculated electric field gradients. Electronic structure calculations predict metallic properties with strong Ag-Sn bonds and also significant Ag-Ag bonding in LuAgSn.     

Mild, powerful, and robust methods for esterification, amide formation, and thioesterification between acid chlorides and alcohols, amines, thiols, respectively

We developed two efficient practical methods for esterification, amide formation, and thioesterification between acid chlorides and alcohols, amines, thiols, respectively. The present mild and robust reaction was performed by two separate methods both by combining cheap and readily available amines, N-methylimidazole, and N,N,N′,N′-tetramethylethylenediamine (TMEDA). Method A uses catalytic N-methylimidazole and TMEDA with an equimolar amount of K₂CO₃, whereas Method B uses equimolar amounts of N-methylimidazole and TMEDA. The salient features are as follows. (i) With regard to reactivity, Method B was superior to Method A for esterification and thioesterification, whereas cost-effective Method A was superior to Method B for amide formation. (ii) Amide formation proceeded smoothly between acid chlorides and less nucleophilic and stereocongested amines such as 2,6-dichloroaniline. (iii) This protocol was applied to the successful synthesis of two agrochemicals, bromobutide and carpropamid.     

Structure and properties of HOO,HOS, HSO,HSS, FSO,FOS and FSS

High quality SCF-MO calculations are reported for the title molecules, including geometry optimization. One-electron properties are presented and discussed, and relative stabilities of (HOS, HSO) and (FOS, FSO) compared. Little experimental geometric data are available at present, but the calculated and experimental geometries of HO₂ agree well.