Ni/Al_2O_3催化2-甲基呋喃加氢制2-甲基四氢呋喃性能的研究

采用浸渍法制备了不同NiO含量的Ni/Al_2O_3催化剂,并进行了2-甲基呋喃加氢制2-甲基四氢呋喃性能的考察。结果表明,在制备的NiO负载量为10%、20%、25%、30%和40%的Ni/Al_2O_3催化剂中,随着NiO负载量增加,加氢反应的选择性与2-甲基呋喃的转化率均呈现出先增加后减小的趋势。其原因是由于适当增加NiO负载量有利于催化剂表面活性中心的形成,有利于加氢反应的进行;但是过度负载的NiO容易堵塞Al_2O_3载体中的介孔通道,降低反应的转化率与选择性。在釜式反应器中进行反应,对加氢反应条件进行了优化,发现在反应压力为3 MPa、反应温度150℃、机械搅拌速率为1000 r/min时,Ni/Al_2O_3催化2-甲基呋喃加氢制2-甲基四氢呋喃具有较高的选择性。当NiO负载量为25%时,2-甲基四氢呋喃的选择性最高为97.1%,2-甲基呋喃的转化率达到99.4%。     

Ni/γ-Al2O3催化剂的2-MF气相加氢合成2-MTHF性能研究

2-甲基四氢呋喃(2-MTHF)是极具市场潜力的生物燃料、绿色溶剂和化学中间体.采用浸渍法制备Ni/γ-Al2O3催化剂,在固定床反应器评价其2-甲基呋喃(2-MF)气相加氢合成2-甲基四氢呋喃(2-MTHF)反应性能.通过XRD、N2等温吸附-脱附、H2-TPR、NH3-TPD、TEM、H2吸附和XPS对催化剂结构和表面性质进行表征,研究Ni负载量、焙烧温度和反应条件对催化剂性能的影响规律.结果表明:Ni/γ-Al2O3催化剂的Ni金属面积、晶粒尺寸、反应温度和压力都会影响2-MF的转化率;孔结构、酸量和反应温度是影响2-MTHF选择性的主要原因,平均孔径大、酸量大和适宜的反应温度有利于提高2-MTHF选择性. 400℃焙烧的负载量为15%的Ni/γ-Al2O3催化剂, Ni金属面积大、晶粒尺寸小、总酸量多,催化剂表面的金属活性中心与酸性中心协同作用促进了2-MF呋喃环上C=C加氢生成2-MTHF,性能较优.在2 MPa、100℃、WHSV=2.7 h-1、H2/2-MF=6.4的条件下,该催化剂上2-MF转化率为99.8%, 2-MTHF选择性为98.0%,催化剂可以稳定运行40 h.     

磷改性Cr2O3/Al2O3催化4-乙基酚转化制轻质芳烃

以烷基酚转化为轻质芳烃（苯和甲苯）为目标，制备了Cr₂O₃/Al₂O₃催化剂，并以4-乙基酚为模型化合物研究了其加氢反应性能。体积空速、氢油比、反应压力和温度升高时，脱烷基率、芳烃总选择性、轻质芳烃选择性呈先增大后减小的趋势，反应温度对转化率影响较大。以不同浓度磷酸对Cr₂O₃/Al₂O₃进行改性，随着磷酸用量的增大，催化剂酸量总体增大，主要是弱酸和中强酸，酸强度先增加后降低，磷酸用量较高时，弱酸增加幅度较大。与未改性相比，质量分数8%磷酸改性Cr₂O₃/Al₂O₃上4-乙基酚转化率99.5%，脱烷基率提升9.4%，达74.4%，轻质芳烃选择性提高4.0%，达到57.0%，以较高选择性实现了转化制轻质芳烃，同时，芳烃总选择性高达80.4%，较高程度保持了芳环不被破坏。提出了Cr₂O₃/Al₂O₃上4-乙基酚加氢反应的路径并对反应机理进行了研究。     

Ru-Ni/Al2O3催化马来酸二甲酯加氢性能研究

以Al₂O₃为载体,RuCl₃·xH₂O及Ni（NO₃）₂·6H₂O为活性组分前驱体,采用吸附-沉淀法制备系列Ru-Ni/Al₂O₃催化剂,以马来酸二甲酯（DMS）催化加氢为探针反应,考察了活化条件和Ni的添加量对催化剂性能的影响。随Ni负载量的升高,Ru-Ni/Al₂O₃催化剂活性呈现先升高后降低的趋势,在Ni：Ru的原子比为6：1时（催化剂Ru₁Ni₆/Al）催化活性最高。催化剂Ru₁Ni₆/Al在氢气中200 ℃直接还原后的平均转化率与氢气中400 ℃还原后的平均转化率接近,达到了单组分Ru/Al催化剂的1.5倍以上。XPS、XRD、H₂-TPR数据表明,Ru与Ni之间发生了较强的相互作用,Ni的加入促进了金属Ru在载体上的分散,提高了催化活性。     

Cu/ZnO催化糠醛气相加氢制2-甲基呋喃的研究

通过共沉淀法制备一系列铜锌催化剂,用于固定床上糠醛气相加氢制2-甲基呋喃的研究。采用X射线衍射仪(XRD)、N_2吸附-脱附、扫描电子显微镜(SEM)、H_2-程序升温还原(H_2-TPR)、NH_3-程序升温脱附(NH_3-TPD)表征,分析催化剂中Cu0和ZnO在催化反应中的作用。结果表明,Cu~0是糠醛加氢的活性中心,氧化锌的加入减小了催化剂晶粒粒径、增大了催化剂比表面积、利于催化剂还原和增加催化剂表面弱酸性位。当Cu/Zn物质的量比为1∶2时,Cu_1Zn_2催化剂具有适宜氧化还原活性中心及弱酸位数量,对2-甲基呋喃表现出较高的选择性。Cu_1Zn_2催化剂在常压、反应温度为200℃、氢醛物质的量比为4∶1、糠醛体积空速为0.3 h-1条件下,糠醛转化率100.0%,2-甲基呋喃选择性最高为93.6%。反应稳定运行200 h后,糠醛转化率仍为100.0%,2-甲基呋喃选择性为80.0%,糠醇选择性为11.4%。     

不同硅源的Cu/SiO2催化糠醛加氢制2-甲基呋喃

以硅溶胶和气相二氧化硅为载体,采用氨蒸法制备了Cu/SiO₂-sol和Cu/SiO₂-aer两种催化剂,采用N₂吸附脱附、X射线衍射（XRD）、傅里叶红外光谱（FT-IR）、透射电子显微镜（TEM）、N₂O-H₂滴定、氢气程序升温还原（H₂-TPR）、氨程序升温脱附（NH₃-TPD）及X射线光电子能谱（XPS）对样品进行表征,在固定床反应器中考察两种催化剂对糠醛气相加氢制2-甲基呋喃的催化性能。结果表明,Cu/SiO₂-sol催化剂具有更好的催化活性,在150 h反应时间内,糠醛转化率为100%,2-MF选择性在91%以上。这主要归因于以硅溶胶为硅源可以生成更多页硅酸铜,还原后催化剂表面Cu的分散性更高、弱酸位更多,有利于提高糠醛的转化率与2-甲基呋喃的选择性。同时Cu/SiO₂-sol具有较大的孔容孔径,有利于降低反应过程中积炭,延长催化剂寿命。     

丙烷在Ce-Fe/Al2O3/cordierite上选择性催化还原NO

利用凝胶溶胶法和浸渍法制备了Ce-Fe/Al₂O₃/cordierite催化剂,实验研究了其催化丙烷选择性还原NO的特性。结果表明,当铈的负载量从1%增加至5%时,Ce-Fe/Al₂O₃/cordierite的C₃H₈-SCR性能先增强后减弱,3.5Ce-Fe/Al₂O₃/cordierite具有最佳的脱硝性能,在有氧条件下,600℃时可实现96.5%的脱硝效率。Ce的加入能够提升Fe/Al₂O₃/cordierite催化剂的抗硫性能。烟气中通入0.02%的SO₂后,3.5Ce-Fe/Al₂O₃/cordierite催化丙烷还原NO的转化率始终维持在93%,而没有经过Ce修饰的Fe/Al₂O₃/cordierite的NO转化率从88%下降为80%左右。利用XRD、N₂吸附-脱附、SEM、H₂-TPR、吡啶吸附红外光谱等手段研究了催化剂的物理化学性质。结果表明,加入助剂铈能与Fe形成了固溶体,增加催化剂表面Lewis酸浓度和氧化还原能力,从而提高了催化丙烷还原NO的性能。过多的铈引入会减少Fe₂O₃结晶体的形成,不利于在C₃H₈-SCR反应中形成NO₂/NO₃^-物种,从而导致NO还原效率下降。     

二维M-Co3O4负载Ir对香草醛加氢脱氧性能研究

以二维金属-有机框架M-Co₃O₄为载体制备了具有高活性的Ir/M-Co₃O₄催化剂.采用X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、电感耦合等离子体发射光谱仪(ICP-OES)、 N₂物理吸/脱附等方法对催化剂进行了表征,并研究了催化剂、温度、时间、溶剂等因素对香草醛加氢脱氧反应的影响.结果表明, Ir/M-Co₃O₄催化剂具有较好的普适性和稳定性,在香草醛加氢脱氧制备4-甲基愈创木酚(MMP)反应中表现出较高的活性和选择性,香草醛的转化率达100%, MMP的选择性不低于99%.     

KF/Al2O3催化剂上苯脲醇解合成苯氨基甲酸甲酯的研究

采用浸渍法制备负载KF固体碱催化剂,应用于苯脲和甲醇制备苯氨基甲酸甲酯的反应,考察了氧化物载体、卤化钾种类对催化剂性能的影响,KF/Al₂O₃催化剂显示出良好的催化活性和苯氨基甲酸甲酯的选择性。通过对KF/Al₂O₃催化剂中KF的负载量和催化剂焙烧温度的研究发现,在500 ℃焙烧4 h、负载质量分数50%KF的催化剂能够更好地促进MPC生成,苯脲转化率和苯氨基甲酸甲酯选择性分别达到96.5%和86.3%。XRD分析表明,KF与Al₂O₃之间存在较强的相互作用,部分转化为K₃AlF₆。KF与K₃AlF₆分别对甲醇的活化和苯脲的选择性起促进作用,两者的协同效应共同促进了目标产物苯氨基甲酸甲酯的生成。     

CoMo/ZrO2-Al2O3催化剂的制备及其加氢脱氧性能

以ZrOCl₂·6H₂O和Al₂(SO₄)₃为原料,采用超声波共沉淀法制得一系列不同ZrO₂质量分数的ZrO₂- Al₂O₃复合氧化物载体;并以该复合氧化物为载体,采用等体积浸渍法制得Co和Mo质量分数分别为6.0%和16.0%的CoMo/ZrO₂-Al₂O₃催化剂。BET、XRD、H₂-TPR和NH₃-TPD等表征结果表明,ZrO₂-Al₂O₃复合氧化物载体具有较高的比表面积与较大的孔容、孔径,随着复合载体中ZrO₂质量分数的增加,复合载体比表面积逐渐减小。ZrO₂-Al₂O₃复合载体能高度分散活性组分,钴钼负载量接近其在载体上的单层分散阈值。相比于CoMo/Al₂O₃,CoMo/ZrO₂-Al₂O₃催化剂具有较高的还原性能和较多的表面酸性活性中心,由此导致其在苯酚加氢脱氧(HDO)反应中,具有较高的加氢脱氧活性和苯选择性。
     

Catalytic hydrogenation of 1,4-phenylenediamine to 1,4-cyclohexanediamine

Catalytic hydrogenation of 1,4-phenylenediamine to 1,4-cyclohexanediamine using Ru/Al₂O₃ as a catalyst was carried out in water, and the results were compared with those in isopropanol and SC-CO₂. 80% 1,4-phenylenediamine conversion with 87% selectivity to 1,4-cyclohexanediamine was achieved on 5% Ru/Al₂O₃ catalyst at 90°C and H₂ pressure of 4 MPa. The hydrogenation of 1,4-phenylenediamine is influenced by the solvent. A systematic study of the hydrogenation of 1,4-phenylenediamine revealed that the reaction was consecutive. The longer the time, the lower was the CHDA selectivity. Also, the reaction temperature was an important parameter and played a vital role in preventing the formation of side products.     

Selective conversion of furfuryl alcohol to 2-methylfuran over nanosilica supported Au:Pd bimetallic catalysts at room temperature

Using gold and palladium supported catalysts, the selective hydrogenation of furfuryl alcohol into 2-methylfuran at 25 °C was examined. The use of 2-methylfuran has become applicable in the perfumery and personalised care product industry, and it has been shown that there are two conditions under which Au:Pd/SiO₂ catalysts are successful for selectivity to 2-methylfuran at 25 °C and (1 bar, H₂). Moreover, this study has shed light on the effectiveness of several reaction conditions (supports and catalyst amount).     

Liquid phase selective hydrogenation of phenol to cyclohexanone over Ru/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocatalyst under mild conditions

Highly monodispersed ruthenium nanoparticles were prepared via wet impregnation technique using RuCl₃ · nH₂O as a precursor. Ru nanoparticles were supported on Al₂O₃ to synthesize Ru nanocatalyst. The nanocatalyst was characterized by various techniques like XRD, SEM, TEM and BET analysis. The catalyst was used for hydrogenation of phenol under mild condition. The activity of the catalyst was checked by varying different parameters such as reaction temperature, time, H₂ partial pressure, metal loading and catalyst amount. The catalyst was recovered from product and reused up to four times without significant loss in its catalytic activity. After a reaction time of 1 h, Ru/Al₂O₃ nanocatalyst showed high reactivity (82% conversion) and selectivity to cyclohexanone (67%) at 80°C and 20 bar hydrogen pressure.     

Effects of Mo2C loading and H2S concentration on Mo2C/Al2O3 catalyst applied in sulfur‐resistant methanation

Mo₂C/Al₂O₃ catalyst was prepared by the impregnation method with urotropine and ammonium paramolybdate. The catalytic effect of Mo₂C as a typical transition‐metal carbide in sulfur‐resistant methanation was studied. The catalysts prepared were characterized by N₂ adsorption–desorption, X‐ray diffraction, transmission electron microscopy, H₂‐temperature‐programmed reduction, and Raman spectra, with the results confirming the formation of β‐molybdenum carbide on the surface of the catalysts. Studies on catalysts with different loading doses indicate that the optimal loading of Mo₂C/Al₂O₃ is about 15 wt.%, which enables CO conversion rate of up to 47%, with methane selectivity of up to 53%. This work further explored the effect of different concentrations of H₂S in the raw gas on the performance of the catalyst, with the results showing that high concentration of H₂S (>1500 ppm) can lead to sulfuration of active species on the catalyst, while resulting in a decrease in the catalytic activity.     

组合型Pt3Sn/Al2O3催化剂用于芳香硝基化合物一锅法合成N-烷基芳胺

采用吸附法制备了组合型Pt₃Sn/Al₂O₃双金属催化剂, 将该催化剂用于芳香硝基化合物原位液相加氢一锅法合成N-烷基芳胺. 研究表明, 在503 K, 空速为7.5 h^-1, 水体积分数为5%时, 1%(质量分数)Pt₃Sn/Al₂O₃催化剂具有较高的催化性能, 硝基苯的转化率为100%, N-乙基苯胺和N,N-二乙基苯胺的总选择性为98.2%. 同时,该催化剂对原位液相加氢烷基化反应具有一定普适性, 本文研究的14 种芳香硝基化合物与低级脂肪醇反应,均具有较高的N-烷基化产率.     

The catalytic performance of different promoted iron catalysts on combined supports Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for carbon dioxide hydrogenation

Global warming, fossil fuel depletion and fuel price increases have motivated scientists to search for methods for the storage and reduction of the amount of greenhouse gases, especially CO₂. The hydrogenation process has been introduced as an emerging method of CO₂ capture and convertion into value-added products. In this study, new types of catalysts are introduced for CO₂ hydrogenation and are compared based on catalytic activity and product selectivity. The physical properties of the samples are specified using BET. Iron catalysts supported on γ-Al₂O₃ with different metal promoters (X = Ni, K, Mn, Cu) are prepared through the impregnation method. Moreover, Fe–Ni catalysts supported on HZSM5-Al₂O₃ and Ce–Al₂O₃ are synthesized. Samples are reduced by pure H₂ and involved in hydrogenation reaction in a fixed bed reactor (H₂/CO₂ = 3, total pressure = 10 MPa, temperature = 523 K, GHSV = 2000, 1250 nml/min). All catalysts provide high conversion in hydrogenation reactions and the results illustrate that the selectivity of light hydrocarbons is higher than that of methane and CO. It is found that Ni has a promoting effect on the conversion fluctuations throughout the reaction with 66.13% conversion. Using combined supported catalysts leads to enhancing catalytic performance. When Fe–Ni/γ–Al₂O₃—HZSM5 is utilized, CO₂ conversion is 81.66% and the stability of the Fe–Ni catalyst supported on Al₂O₃ and Ce–Al₂O₃ furthey improves.     

Chemo-bio catalyzed synthesis of <Emphasis Type="Italic">R</Emphasis>-1-phenylethyl acetate over bimetallic PdZn catalysts,lipase, and Ru/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>. part I

One-pot synthesis of R-1-phenyethylacetate at 70°C was investigated using three different catalysts simultaneously, namely a bimetallic PdZn/Al₂O₃ as a hydrogenation catalyst, an immobilized lipase as an acylation catalyst and Ru/Al₂O₃ as a racemization catalyst. The most active bimetallic catalyst was PdZn/Al₂O₃ calcined at 300°C and reduced at 400°C, whereas the most selective although less active catalyst was the one being calcined and reduced at 500°C. The highest selectivity to R-1-phenylethyl acetate over this catalyst was 32 at 48% conversion. Ru/Al₂O₃ was confirmed to have a positive effect on the formation of the desired product, although it was not very active in the racemization during one-pot synthesis.     

Highly Selective Aldol Condensation Using Amine-functionalized SiO2-Al2O3 Mixed-oxide under Solvent-free Condition

A series of amine catalysts supported on mesoporous molecular sieves SiO₂/Al₂O₃ with trimethoxysilylpropylamine [(CH₃O)₃Si(CH₂)₃NH₂] loading varying from 3 mmol to 6 mmol were synthesized by impregnation method. The aldol condensation of various aromatic aldehydes and 1‐heptanal was used to test the acid‐base cooperativity of amine‐functionalized SiO₂/Al₂O₃. The effects of solvent, reaction temperature, benzaldehyde to 1‐heptanal molar ratio, different supports (SiO₂, Al₂O₃ and SiO₂‐Al₂O₃), catalyst amount and recyclability of the catalyst were investigated. Sample containing 5 mmol amine loaded showed highest benzaldehyde conversion (100%) and selectivity (97%) for jasminaldehyde.     

Chemo-bio catalyzed synthesis of <Emphasis Type="Italic">R</Emphasis>-1-phenylethyl acetate over bimetallic PdZn catalysts,lipase, and Ru/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>. Part II

One-pot synthesis of R-1-phenyethylacetate at 70°C was investigated using three different catalysts simultaneously, namely a bimetallic PdZn/Al₂O₃ as a hydrogenation catalyst, an immobilized lipase as an acylation catalyst and Ru/Al₂O₃ as a racemization catalyst. The most active bimetallic catalyst was PdZn/Al₂O₃ calcined at 300°C and reduced at 400°C, whereas the most selective although less active catalyst was the one being calcined and reduced at 500°C. The highest selectivity to R-1-phenylethyl acetate over this catalyst was 32 at 48% conversion. Ru/Al₂O₃ was confirmed to have a positive effect on the formation of the desired product, although it was not very active in the racemization during one-pot synthesis.     

The influence of La2O3 and TiO2 on NiO/MgO/α-Al2O3

Summary The effect of La₂O₃ and TiO₂ on product selectivity, methane conversion and coke formation over NiO/MgO/ α -Al₂O₃ catalyst were studied in a simultaneous steam and CO₂ reforming of methane to syngas. La₂O₃ and TiO₂ were added to the catalyst via incipient wetness impregnation and bulk precipitation techniques and catalyst activity was tested in a fixed bed quartz reactor. Results reveal that although the addition of these oxides has no effect on the product selectivity and methane conversion, but can reduce coke formation on the surface of the catalysts as it can enhance the mobility of lattice oxygen anions. The results further show that the catalysts prepared by bulk precipitation technique decrease the coke formation more effectively.