齐多夫定替代模板分子印迹聚合物的制备及其在血清样品固相萃取中的应用

制备了齐多夫定(AZT)替代模板分子印迹聚合物(MIP)用于血清样品的前处理。利用计算机模拟选择最佳单体甲基丙烯酸和交联剂二乙烯基苯,用自制的替代模板(AZT酯化物)制备了AZT的MIP。将替代模板MIP作为固相萃取吸附剂,进行固相萃取并优化萃取条件。确定pH 7的KH2PO4缓冲溶液为上样溶剂,2%(V/V)乙腈/pH 7的KH2PO4缓冲溶液为淋洗剂,甲醇/乙酸(9:1,V/V)作为洗脱剂。渗漏实验结果显示齐多夫定MIP的吸附容量为9.10 mg/g,而非分子印迹聚合物(NIP)的吸附容量仅为1.77 mg/g。以AZT酯化物和拉米夫定为结构类似物,进行吸附实验,发现MIP具有高选择性。本文所制备的替代模板分子印迹聚合物在水溶液体系中表现出了很好的识别能力。血清样品经印迹聚合物固相萃取后,用高效液相色谱法测定,发现MIP萃取柱回收率为99.3%,NIP萃取柱仅为13.2%,说明替代模板MIP可用于血清样品中AZT的选择性分离富集,并可以避免模板渗漏。     

替米考星分子印迹聚合物的制备及其固相萃取研究

以泰乐菌素为虚拟模板分子,甲基丙烯酸为功能单体,乙二醇二甲基丙烯酸酯为交联剂,合成了对替米考星具有高选择性的分子印迹聚合物。考察了二甲基甲酰胺、甲醇、丙酮和氯仿4种致孔剂对合成聚合物性能的影响。通过正交实验优化的聚合配方为:1.0mmol泰乐菌素,8.0mmol甲基丙烯酸,20.0mmol乙二醇二甲基丙烯酸酯,6.0mL氯仿,20.0mg偶氮二异丁腈。研究了将该聚合物作为固相萃取填料分离、富集替米考星的萃取条件和萃取性能。当萃取柱依次用甲醇和水(pH9.0)活化,乙腈溶液上样,甲醇和氯仿分别洗涤,3mL氨化甲醇(95:5,V/V)洗脱时,替米考星在分子印迹固相萃取柱上的回收率达到90%以上,而非分子印迹固相萃取柱的回收率仅为32%。     

分子印迹固相萃取联用高效液相色谱分离测定海水中的膝沟藻毒素GTX1,4

采用分子印迹技术,以鸟嘌呤核苷为虚拟模板,本体聚合,合成GTX1,4的分子印迹聚合物(MIP).傅里叶红外变换光谱(FT-IR)和扫描电子显微镜(SEM)的结果显示,MIP具有分布均匀、大小均一的孔穴.平衡吸附实验表明,分子印迹聚合物(MIP)比非分子印迹聚合物(NIP)具有更高的结合容量,对膝沟藻毒素GTXI,4有更好的选择性.用MIP填充固相萃取小柱(MISPE),以0.1 mol/L乙酸溶液为淋洗液,甲醇-水(95∶5,V/V)溶液为洗脱液时回收率最高,达到85.0％.用优化后的淋洗洗脱条件测定微小亚历山大藻和塔玛亚历山大藻藻液中的GTX1,4,分别为1.10和0.99 μg/L,RSD分别为3.3％和4.4％,说明本方法具有较好的检测限和较高的测定精密度.     

洛克沙胂分子印迹聚合物的制备及其固相萃取研究

以阿散酸为虚拟模板分子,2-乙烯吡啶为功能单体,乙二醇二甲基丙烯酸酯为交联剂,合成了对洛克沙胂具有高选择性的分子印迹聚合物。通过考察致孔剂、单体及交联剂等因素对合成聚合物性能的影响,获得优化聚合配方为:阿散酸、2-乙烯吡啶、乙二醇二甲基丙烯酸酯、甲醇-乙腈(1∶1,V/V)及偶氮二异丁腈之比为1 mmol∶4 mmol∶20 mmol∶6 mL∶60 mg。合成印迹聚合物对洛克沙胂的最大吸附量为0.93 mg/g,作为固相萃取填料分离、富集洛克沙胂的优化萃取条件为:水和乙腈活化平衡,乙腈上样,水和甲醇依次淋洗,5%甲酸甲醇溶液洗脱。洛克沙胂在分子印迹固相萃取柱上的回收率达到95%以上,而非分子印迹固相萃取柱的回收率仅为43.1%。制备小柱应用于池塘水中洛克沙胂的净化富集,检测限可达0.05 mg/L。     

邻苯二甲酸二（2-丙基庚）酯分子印迹固相萃取剂的制备及其应用

以邻苯二甲酸二辛酯（DOP）为虚拟模板分子,α-甲基丙烯酸（MAA）为功能单体,乙二醇二甲基丙烯酸酯（EDMA）为交联剂,采用沉淀聚合法制备了对邻苯二甲酸二（2-丙基庚）酯（DPHP）具有高选择性的分子印迹聚合物（MIP）。用紫外分光光度法探索了不同功能单体与模板分子的结合能力,与功能单体丙烯酸（AA）相比,MAA与DOP的结合能力更强,其最佳结合的物质的量比为6：1。考察MIP对DOP、DPHP、邻苯二甲酸二甲酯（DMP）、邻苯二甲酸二丁酯（DBP）的选择吸附性能,发现该聚合物对DPHP具有更高的选择吸附性。以制备的聚合物为固相萃取填料,结合HPLC分析,考察了淋洗剂与洗脱剂的种类和用量对DPHP回收率的影响。将DPHP甲醇溶液加载至萃取柱后用1 mL甲醇-水（1：9,v/v）淋洗,5 mL甲醇-乙酸（9：1,v/v）洗脱,DPHP在分子印迹固相萃取（MISPE）柱上的回收率达到96.8%,而在非印迹固相萃取（NISPE）柱上的回收率仅为52.9%。将建立的MISPE-HPLC方法应用于测定兔口服DPHP后不同时间点兔血清中DPHP的浓度,发现其血药浓度的最大值为5.88 μg/mL,达峰值时间为4 h,DPHP加标回收率为90.0%~92.0%,相对标准偏差小于5%。     

儿茶素活性成分分子印迹聚合物的固相萃取研究

以表没食子儿茶素没食子酸酯(Epigallocatechin-gallate,EGCG)为模板分子,α-甲基丙烯酸为功能单体,乙二醇二甲基丙烯酸酯为交联剂,在光冷引发条件下合成EGCG分子印迹聚合物,利用该聚合物制成分子印迹固相萃取柱,用于固相萃取茶叶提取物茶多酚,对萃取柱中的清洗液、洗脱剂、上载量等进行了选择.结果表明,在萃取柱上载样品之后,先用V(甲醇):V(水)＝1:9溶液进行清洗,再用V(甲醇):V(乙酸)＝9:1混合液进行目标分子的洗脱,可以得到比较纯的目标物质EGCG(色谱峰相对峰面积达92.4%),萃取柱在上载样品并进行清洗、洗脱之后,EGCG的回收率达69.3%.分子印迹柱具有较好的稳定性和耐用性能,使用20次后其选择性识别能力仍未降低,但空白印迹柱却没有这样的选择性识别能力.     

橄榄醇分子印迹聚合物的制备及评价(英文)

以橄榄醇为模板分子,α-甲基丙烯酸(MAA)为功能单体,乙二醇二甲基丙烯酸酯(EDMA)为交联剂,甲苯和十二醇为溶剂,通过本体聚合法制备了橄榄醇分子印迹聚合物。利用平衡结合实验、扫描电镜(SEM)及红外光谱(FTIR)对分子印迹聚合物(MIP)进行了表征,并用该聚合物进行了加标麦麸中橄榄醇的固相萃取(SPE)研究。平衡结合实验表明MIP对模板分子具有更好的识别性。Scatchard分析表明对橄榄醇分子的吸附存在2类不同结合位点,其中高亲和力结合位点和低亲和力结合位点的解离常数分别为0.021和1.002 mmol/L,相应的最大表观结合量分别为18.74和135.9 μmol/g。在优化的固相萃取条件下,MIP固相萃取柱对加标麦麸中橄榄醇的回收率达到97.8%~98.8%,相对标准偏差为2.8%~4.2%(n=5),线性范围为0.1~100 mg/L,检出限(S/N=3)为0.062 mg/L。与非印迹聚合物(NIP)柱及市售聚苯乙烯/二乙烯基苯(PLS)柱相比,MIP柱的选择性更强,回收率更高,纯化效果更好。     

分子印迹固相萃取牛奶中甲胺磷

以甲胺磷为印迹分子、α-甲基丙烯酸为功能单体及三羟甲基丙烷三丙烯酸酯为交联剂,通过悬浮聚合法制备甲胺磷分子印迹聚合物(MIP)微球,并用该聚合物进行了牛奶中甲胺磷残留的固相萃取研究.静态吸附实验表明,在结构相似物乙酰甲胺磷和水胺硫磷为竞争底物存在下,MIP对甲胺磷有良好的吸附识别能力.在优化条件下,印迹分子的固相萃取回收率达96.4%,能够用于甲胺磷的富集,而空白聚合物却不具备这样的特性.当实际牛奶样品中甲胺磷、乙酰甲胺磷和水胺硫磷加标水平为100μg/kg时,甲胺磷回收率达87.4%,乙酰甲胺磷和水胺硫磷的回收率低于15%.结果表明分子印迹固相萃取对甲胺磷有很好的专一选择性,且回收率能够满足农药残留分析要求.在相同实验条件下,与C18固相萃取柱进行比较,分子印迹固相萃取的选择性及样品净化能力优势明显.     

克百威分子印迹聚合物的合成及其性能评价

以克百威为模板分子,甲基丙烯酸(MAA)为功能单体,二甲基丙烯酸乙二醇酯(EGDMA)为交联剂,采用沉淀聚合的方法制备了克百威分子印迹聚合物。通过红外光谱分析得到模板和功能单体的最佳配比为n(carbofuran)∶n(MAA)=1∶6。印迹聚合物的红外光谱测定结果表明,聚合物中存在与模板分子相互作用的特征基团;从印迹聚合物的扫描电镜图观察到分子印迹聚合物(MIP)与空白聚合物(NIP)的表面形态不同,可推论MIP存在与模板分子相互识别的结合位点。通过静态平衡结合法研究了模板分子聚合物的吸附能力、结合动力学和选择特性。结果表明,与非印迹聚合物相比,印迹聚合物对克百威具有较强的吸附特性和很好的专一选择性,3h后基本达到最大吸附量。采用固相萃取柱预处理样品,用高效液相色谱法测定自来水中10、50、100mg/L克百威的加标回收率为94%～117%,相对标准偏差(n=3)为2.5%～4.7%。     

分子印迹固相萃取技术检测江水、尿液及牛奶中雌激素残留

以β-雌二醇和炔雌醇的分子印迹聚合物为填料制备固相萃取小柱,选择60%(V/V)甲醇-水溶液作为雌激素的淋洗液,甲醇-乙酸(9:1,V/V)为洗脱液,洗脱两次可彻底洗脱固相萃取小柱中目标分子.以建立的萃取条件对上海黄浦江水、尿液、牛奶中雌激素进行富集,结合高效液相色谱法,建立了基于分子印迹固相萃取技术检测上述实际样品中...     

Synthetic approaches to parabens molecularly imprinted polymers and their applications to the solid-phase extraction of river water samples

In this paper we describe the synthesis, characterisation and use of two distinct molecularly imprinted polymers (MIPs) prepared using esters of p-hydroxybenzoic acid (parabens) as templates: one MIP was synthesised by precipitation polymerisation using a semi-covalent molecularly imprinting strategy with methyl paraben as the template/target (MIP 1); the second MIP was prepared in monolithic form through a conventional non-covalent molecular imprinting strategy, with butyl paraben as the template (MIP 2). MIP 1 recognized methyl paraben, showed cross-selectivity for other parabens analytes used in the study and higher affinity towards these compounds than did a non-imprinted control polymer. Similarly, MIP 2 demonstrated higher affinity towards paraben analytes than a non-imprinted control polymer.For the analysis of environmental water samples, a solid-phase extraction (SPE) protocol was developed using MIP 2 as sorbent, and results were compared to a SPE using a commercial sorbent (Oasis HLB). With MIP 2 as sorbent and butyl paraben as target, when percolating 500 mL of river water spiked at 1 μg L⁻¹ through the SPE cartridge, and using 1 mL of isopropanol as cleaning solvent, a higher recovery of butyl 4-hydroxybenzoate (butyl paraben) and a cleaner chromatogram where achievable when using the MIP compared to the commercial sorbent.     

Effective separation of dopamine from bananas on 2-(3,4-dimethoxyphenyl)ethylamine imprinted polymer

A 2-(3,4-dimethoxyphenyl)ethylamine imprinted polymer (MIP(pt) ) was prepared via the precipitation polymerization together with a nonimprinted polymer (NIP). The morphology of particles was investigated by scanning electron microscopy and the specific surface areas were estimated by methylene blue adsorption (60.5 ± 3.5 and 36.9 ± 1.2 m(2)/g for MIP(pt) and NIP, respectively). The binding experiments were performed to determine the binding capacity of MIP(pt)/NIP particles toward dopamine. Next, the effects of solvents on loading, washing, and eluting steps were examined on solid-phase extraction (SPE). Methanol-water 85:15 v/v (loading step), methanol (washing step), and 0.04 M aqueous ammonium acetate-methanol 30:70 v/v (eluting step) were selected as the most effective systems. Described SPE protocol was successfully applied for separation of dopamine on 2-(3,4-dimethoxyphenyl)ethylamine imprinted particles. Finally, the molecularly imprinted polymer was used for determination of dopamine in spiked banana extract. The total recovery of dopamine from MIP(pt) was equal to 88.5 ± 4.6%, but from NIP was only 12.8 ± 2.3%. The developed material and method were demonstrated to be applicable for the separation of dopamine from bananas. The commercial sorbent C18 was not suitable to such application.     

Molecularly imprinted polymer with high-fidelity binding sites for the selective extraction of barbiturates from human urine

In this paper we describe the synthesis of a molecularly imprinted polymer (MIP) by precipitation polymerisation, with barbital as the template molecule, and the application of the barbital MIP as a molecularly selective sorbent in the solid-phase extraction (SPE) of barbiturates from human urine samples. The MIP was synthesised by precipitation polymerisation using 2,6-bis-acrylamidopyridine as the functional monomer and DVB-80 as the cross-linking agent. The spherical MIP particles produced were 4.2 ± 0.4 μm in diameter; a non-imprinted control polymer (NIP) in bead form was 4.8 ± 0.4 μm (mean±standard deviation) in diameter. The particles were packed into a solid-phase extraction cartridge and employed as a novel sorbent in a molecularly imprinted solid-phase extraction (MISPE) protocol. The MIP showed high selectivity for the template molecule, barbital, a feature which can be ascribed to the high-fidelity binding sites present in the MIP which arose from the use of 2,6-bis-acrylamidopyridine as the functional monomer. However, the MIP also displayed useful cross-selectivity for other barbiturates besides barbital. For real samples, the MIP was applied for the extraction of four barbiturates from human urine. However, due to the high urea concentration in this sample which interfere the proper interaction of barbiturates onto the MIP, a tandem system using a commercially available sorbent was developed.     

Automated sample preparation based on the sequential injection principle. Solid-phase extraction on a molecularly imprinted polymer coupled on-line to high-performance liquid chromatography

A molecularly imprinted polymer (MIP) prepared using caffeine, as a template, was validated as a selective sorbent for solid-phase extraction (SPE), within an automated on-line sample preparation method. The polymer produced was packed in a polypropylene cartridge, which was incorporated in a flow system prior to the HPLC analytical instrumentation. The principle of sequential injection was utilised for a rapid automated and efficient SPE procedure on the MIP. Samples, buffers, washing and elution solvents were introduced to the extraction cartridge via a peristaltic pump and a multi-position valve, both controlled by appropriate software developed in-house. The method was optimised in terms of flow rates, extraction time and volume. After extraction, the final eluent from the extraction cartridge was directed to the injection loop and was subsequently analysed on HPLC. The overall set-up facilitated unattended operation, operation and improved both mixing fluidics and method development flexibility. This system may be readily built in the laboratory and can be further used as an automated platform for on-line sample preparation.     

Development of andrographolide molecularly imprinted polymer for solid-phase extraction

A method employing molecularly imprinted polymer (MIP) as selective sorbent for solid-phase extraction (SPE) to pretreat samples was developed. The polymers were prepared by precipitation polymerization with andrographolide as template molecule. The structure of MIP was characterized and its static adsorption capacity was measured by the Scatchard equation. In comparison with C(18)-SPE and non-imprinted polymer (NIP) SPE column, MIP-SPE column displays high selectivity and good affinity for andrographolide and dehydroandrographolide for extract of herb Andrographis paniculata (Burm.f.) Nees (APN). MIP-SPE column capacity was 11.9±0.6 μmol/g and 12.1±0.5 μmol/g for andrographolide and dehydroandrographolide, respectively and was 2-3 times higher than that of other two columns. The precision and accuracy of the method developed were satisfactory with recoveries between 96.4% and 103.8% (RSD 3.1-4.3%, n=5) and 96.0% and 104.2% (RSD 2.9-3.7%, n=5) for andrographolide and dehydroandrographolide, respectively. Various real samples were employed to confirm the feasibility of method. This developed method demonstrates the potential of molecularly imprinted solid phase extraction for rapid, selective, and effective sample pretreatment.     

Molecularly imprinted polymer for solid‐phase extraction of ephedrine and analogs from human plasma

A molecularly imprinted polymer (MIP) was synthesized and evaluated to selectively extract ephedrine from human plasma. The MIP synthesis was performed in chloroform with methacrylic acid as a functional monomer and the target alkaloid as a template molecule. The resulting MIP was applied to the selective extraction of ephedrine from a pure aqueous medium. A recovery about 74% was obtained using the MIP with only 7% on the nonimprinted polymer (NIP). A very straightforward selective SPE procedure was then successfully applied to the direct extraction of ephedrine from spiked human plasma with a high extraction recovery (68%) on the MIP with no recovery on the NIP. Moreover, the MIP was used for the selective extraction of catecholamine neurotransmitters, i.e. adrenaline and noradrenaline.     

Synthesis of molecularly imprinted polymers for the application of selective clean-up vinblastine from Catharanthus roseus extract

Molecularly imprinted polymers (MIPs) are synthetic tailor-made polymers with high selectivity towards a particular substance (template). An MIP using vinblastine (VLB) as the template molecule was synthesized and characterized. The presence of monomer-template complexes in a non-covalent way was confirmed by UV-vis spectrometry analysis. The polymerization was performed using methacrylic acid (MAA) as the functional monomer, ethylene glycol dimethacrylate (EGDMA) as the cross-linking agent, and toluene as the porogenic solvent by a thermo-polymerization method. The characterization of the obtained MIP was evaluated by scanning electron microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis. It was observed that the morphology of the MIP was more porous and rough, and the surface area had a significant increase compared with that of the non-imprinted polymer (NIP). This MIP was used as the sorbents of solid-phase extraction (SPE) to assess the selectivity of the MIP after optimization of the SPE protocol. VLB was specifically adsorbed on the MIP cartridge, while to vincristine (VCR), the chemical analog of VLB, almost no selective binding appeared. On the basis of the results, Catharanthus roseus extract was applied to the MIP cartridge for investigating its capability to extract VLB from the plant extract, and the capacity of the MIP cartridge was also evaluated. It was shown that the MIP could effectively enrich VLB from C. roseus extract and the recovery amounted to 93.8%. The solvents dissolving the samples had significant influence on the capacity of the MIP cartridge; it was 750 μg/g in toluene, 625 μg/g in chloroform, and 250 μg/g in methanol.     

Molecularly imprinted solid-phase extraction of naphthalene sulfonates from water

A new polymeric sorbent synthesised by exploiting molecular imprinting technology has been used to selectively extract naphthalene sulfonates (NSs) directly from aqueous samples. In the non-covalent molecular imprinting approach used to prepare this polymer, 1-naphthalene sulfonic acid (1-NS) and 4-vinylpyridine (4-VP) were used as a template molecule and functional monomer, respectively, and both dissolved in a mixture of methanol/water (4:1) as porogen together with the cross-linker ethylene glycol dimethacrylate. The new non-covalent molecularly imprinted polymer (MIP) prepared in aqueous environment was used as a sorbent in solid-phase extraction (SPE) to selectively extract a group of naphthalene mono- and disulfonates. When one litre of a standard aqueous solution, which contained a mixture of eight NSs, was percolated through the SPE cartridge, all the NSs were retained on the MIP because of the cross-reactivity of the polymer. Recoveries were higher than 80% for all the compounds even after a clean-up step with methanol (MeOH). The MIP was also used to analyse water from the Ebro river.