Influence of a mixing solvent with tetrahydrofuran and N,N‐dimethylformamide on electrospun poly(vinyl chloride) nonwoven mats

We evaluated the effects of the solvent composition with respect to the solution concentration, applied electric field, and tip‐to‐collector distance on the morphology of electrospun poly(vinyl chloride) (PVC) fibers. The solvent volume ratio was strongly correlated with the diameter of the electrospun fibers with respect to the other processing parameters. Electrospun PVC fibers dissolved in tetrahydrofuran (THF) had diameters ranging from 500 nm to 6 μm; those dissolved in N,N‐dimethylformamide (DMF) had an average diameter of 200 nm. The diameters of the electrospun fibers were obtained from narrow to broad distributions with the solvent composition. Also, the diameters of fibers electrospun from a mixed solvent of THF and DMF were less than 1 μm. The mechanical properties of electrospun PVC nonwoven mats depended on the fiber orientation and linear velocity of the drum surface. With increasing linear velocity of the drum surface, electrospun PVC fibers were arranged toward the machine direction, and the dimensions of the spiral path were shorter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2259–2268, 2002     

Deformation behavior of electrospun poly(L‐lactide‐co‐ε‐caprolactone) nonwoven membranes under uniaxial tensile loading

Biodegradable poly(L ‐lactide‐co‐ε‐caprolactone) copolymers with different L ‐lactide (LLA)/ε‐caprolactone (CL) ratios of 75/25 and 50/50 were electrospun into fine fibers. The deformation behavior of the electrospun membranes with randomly oriented structures was evaluated under uniaxial tensile loading. The electrospun membrane with a higher LLA content showed a significantly higher tensile modulus but a similar maximum stress and a lower ultimate strain in comparison with the membrane with a lower LLA content. The beaded fibers that formed in the membranes caused lower tensile properties. X‐ray diffraction and differential scanning calorimetry results suggested that the electrospun fine fibers developed highly oriented structures in CL‐unit sequences during the electrospinning process even though the concentration was only 25 wt %. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3205–3212, 2005     

原生纤维素静电纺丝的调控

通过电纺非溶剂调控的纤维素溶液, 制备出纤维素电纺纤维. 在N,N-二甲基乙酰胺(DMAc)-氯化锂(LiCl)溶解纤维素体系中, 以DMAc和N,N-二甲基甲酰胺(DMF)作为非溶剂, 添加到高浓度的纤维素溶液中制备电纺溶液. 考察添加非溶剂对纤维素溶液性质和电纺纤维形貌的影响. 结果表明, 添加非溶剂有助于提升纤维素溶液的可纺浓度, 获得分散性较好的电纺纤维, 其中DMF效果最好. 添加非溶剂降低了纤维素溶液的黏度, 使纤维素溶液可纺浓度提高; 添加非溶剂改变了电纺溶液的稳定性, 获得了分散良好的纳米纤维, 从而有助于纤维素射流在电纺过程中快速固化成型.     

Preparation of polybenzoxazole fibers via electrospinning and postspun thermal cyclization of polyhydroxyamide

Polybenzoxazole (PBO) fibers with a submicron diameter were successfully prepared by electrospinning its precursor, polyhydroxyamide (PHA), solutions to obtain the PHA fibers first, followed by appropriate thermal treatments for cyclization reaction. BisAPAF‐IC PHA with two different molecular weights (MWs) were synthesized from a low temperature polymerization of 2,2′‐bis(3‐amino‐4‐hydroxyphenyl) hexafluoropropane (BisAPAF) and isophthaloyl chloride (IC). Using dimethylacetamide (DMAc) and tetrahydrofuran (THF), solvent effects on the electrospinnability of PHA solutions were investigated. For balancing the solution properties, it was found that DMAc/THF mixture with a weight ratio of 1/9 was the best cosolvent to prepare smooth PHA fibers; uniform PHA fibers with a diameter of 325–720 nm were obtained by using 20 wt % PHA/(DMAc/THF) solutions. For a fixed PHA concentration, solutions with a lower MW of PHA yielded thinner electrospun fibers under the same electrospinning condition. After obtaining the electrospun BisAPAF‐IC PHA fibers, subsequent thermal cyclization up to 350 °C produced the corresponding thermally stable BisAPAF‐IC PBO fibers with a diameter of 305–645 nm. The structure of the precursor fibers and the fully cyclized fibers were characterized by FTIR. For the cyclized BisAPAF‐IC PBO fibers, thermogravimetric analysis showed a 5% weight loss temperature at 523 °C in nitrogen atmosphere. The interconnected fiber structure in the BisAPAF‐IC PBO fiber mats was irrelevant to the curing process, but resulted from the jet merging during the whipping process as revealed by the high speed camera images. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8159–8169, 2008     

Ultrafine fibrous cellulose membranes from electrospinning of cellulose acetate

Three solvents, that is, acetone, acetic acid, and dimethylacetamide (DMAc), with a range of solubility parameter δ, surface tension γ, viscosity η and boiling temperature were used to generate mixtures for electrospinning cellulose acetate (CA) (degree of substitution, DS = 2.45). Although none of these solvents alone enables continuous formation of fibers, mixing DMAc with either acetone or acetic acid produced suitable solvent systems. The 2:1 acetone:DMAc mixture is the most versatile mixture because it allows CA in the 12.5–20% concentration range to be continuously electrospun into fibrous membranes. These CA solutions have η between 1.2 and 10.2 poise and γ around 26 dyne/cm and produce smooth fibers with diameters from 100 nm to ～1 μm. Fiber sizes generally decrease with decreasing CA concentrations. The nature of the collectors affects the morphology as well as packing of fibers. Fibers collected on paper have more uniform sizes, smooth surfaces, and fewer defects, whereas fibers collected on water are more varied in size. Electrically conductive solid collectors, such as Al foil and water, favor more tightly packed and less porous membranes. Porous collectors, like paper and copper mesh, produce highly porous membranes. The pores in membranes collected on the Al foil and paper are much better interconnected in the planar directions than those in membranes collected on water. There is evidence that electrospinning induces order in the fibers. Deacetylation of CA membranes is more efficient and complete in NaOH/ethanol than in aqueous NaOH, producing DS values between 0.15 and 2.33 without altering fiber surfaces, packing, or organization. The fully regenerated cellulose membranes are similarly hydrophilic as commodity cellulose fibrous matrices but absorb nearly 10 times as much water. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2119–2129, 2002     

Biodegradable electrospun mat: Novel block copolymer of poly (p‐dioxanone‐co‐L‐lactide)‐block‐poly(ethylene glycol)

Ultrafine fibers of a laboratory‐synthesized new biodegradable poly(p‐dioxanone‐co‐L ‐lactide)‐block‐poly(ethylene glycol) copolymer were electrospun from solution and collected as a nonwoven mat. The structure and morphology of the electrospun membrane were investigated by scanning electron microscopy, differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and a mercury porosimeter. Solutions of the copolymer, ranging in the lactide fraction from 60 to 80 mol % in copolymer composition, were readily electrospun at room temperature from solutions up to 20 wt % in methylene chloride. We demonstrate the ability to control the fiber diameter of the copolymer as a function of solution concentration with dimethylformamide as a cosolvent. DSC and WAXD results showed the relatively poor crystallinity of the electrospun copolymer fiber. Electrospun copolymer membrane was applied for the hydrolytic degradation in phosphate buffer solution (pH = 7.5) at 37 °C. Preliminary results of the hydrolytic degradation demonstrated the degradation rate of the electrospun membrane was slower than that of the corresponding copolymers of cast film. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1955–1964, 2003     

二氧化碳-环氧丙烷共聚物电纺纤维形貌研究

利用电纺丝技术制备了二氧化碳环氧丙烷共聚物超细纤维,研究了喷丝口电势、纺丝距离、浓度、溶剂等因素对纤维形貌、直径及均一性的影响.实验结果表明,利用电纺丝法可以制备直径在小于200nm到7μm二氧化碳环氧丙烷共聚物纤维;喷丝口电势和浓度对于共聚物电纺丝纤维是否形成串珠结构有重要影响;电势、距离和纺丝液浓度都对纤维直径及分散系数有较大影响,在一定范围内,随着喷丝口电势增加,纤维平均直径变大而分散系数变小;纺丝距离增大使得纤维平均直径变小,分散系数变大;浓度的增大使得纤维平均直径变大,分散系数变小;不同溶剂配制的溶液体系制备的电纺丝纤维形貌有很大差异,在二氯甲烷和丁酮的体系中,分别观察到了两组较为集中的直径分布.     

Characterization of cellulose fibers electrospun using ionic liquid

Nonwoven fibers of cellulose were obtained by electrospinning of cellulose in an ionic liquid, 1-butyl-3-methylinmidazolium chloride (BMIMCl), which is known to be one of the non-volatile solvents. The electrospinning setup was modified in such a way that the syringe was contained in a constant-temperature chamber because of the high melting point of BMIMCl, and the electrospun fibers were collected on the water, which immediately removed the remnant solvent from the electrospun cellulose fibers. The effect of the viscosity of the cellulose solution in BMIMCl on the size and the structure of the fibers was investigated. The crystalline structure of cellulose was examined by X-ray diffraction. Also, the effect of dimethyl sulfoxide, which was expected to induce swelling of cellulose, was studied. The minimum diameter of the continuous electrospun cellulose fibers obtained in this work ranged between 500 and 800 nm.     

Processing and characterization of oriented electrospun poly(vinylidene fluoride) mats

Mats of highly oriented poly(vinylidene fluoride) nanofibers were electrospun by means of a conventional electrospinning equipment; the orientation, however, was obtained using a disk collector rotating at a speed of 4000 rpm and a device that reduced the influence of air displacement during nanofiber orientation. Thermal transitions of the mats were determined by differential scanning calorimetry, the predominant crystalline phase by Fourier transform infrared spectroscopy and wide‐angle X‐ray scattering and the nanofiber orientation and morphology by scanning electron microscopy. Relative permittivity, loss index, stable remnant polarization, and coercive field of the mats were also determined and compared with those obtained for a mat electrospun at 2000 rpm and an oriented commercial film. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 000: 000–000, 2012     

Diameter control of electrospun polyacrylonitrile/iron acetylacetonate ultrafine nanofibers

Electrospinning is the process of producing ultrafine fibers by overcoming the surface tension of a polymer solution using high voltage. In this work, the effects of both solution properties (viscosity, conductivity, and surface tension) and operational conditions (voltage, feed rate, and spinneret‐collector distance), on the structure of electrospun polyacrylonitrile nanofibers, were systematically investigated. Iron acetylacetonate was added to the electrospinning solution to control fiber diameter by selectively adjusting solution properties. It was found that, with increased salt concentration, the fiber diameter increases and then passes through a maximum due to changes in solution viscosity, conductivity, and surface tension. In addition, the fiber diameter increases with increase in voltage, feed rate, and spinneret‐collector distance. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1611–1618, 2008     

Polyaniline/poly(methyl methacrylate) coaxial fibers: The fabrication and effects of the solution properties on the morphology of electrospun core fibers

Electrically conductive polyaniline (PANi)/poly(methyl methacrylate) (PMMA) coaxial fibers were prepared through the chemical deposition of PANi onto preformed PMMA fibers via in situ polymerization. PMMA fibers were prepared as core materials via electrospinning. Spectral studies and scanning electron microscopy observations indicated the formation of PANi/PMMA coaxial fibers with a diameter of approximately 290 nm and a PANi layer thickness of approximately 30 nm. The conductivity of the PANi/PMMA coaxial fibers was significantly higher than that of electrospun fibers of PANi/poly(ethylene oxide) blends and blend cast films of the same PANi composition. To reproducibly generate uniform‐core polymer fibers, the organic solution properties that affected the morphology and diameter of the electrospun fibers were investigated. The polymer molecular weight, solution concentration, solvent dielectric constant, and addition of soluble organic salts were strongly correlated to the morphology of the electrospun fiber mat. In particular, the dielectric constants of the solvents substantially influenced both the fiber diameter and bead formation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3934–3942, 2004     

Electrospinning of polystyrene/poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylene vinylene) blends

Ultrafine polystyrene (PS)/poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylene vinylene) (MEH‐PPV) fibers were successfully prepared by electrospinning of PS/MEH‐PPV solutions in chloroform, 1,2‐dichloroethane, and tetrahydrofuran (THF). Three concentrations of the solutions were prepared: 8.5, 16, and 23.5% (w/v), with the compositional weight ratios between PS and MEH‐PPV being 7.5:1, 15:1, and 22.5:1, respectively. Smooth fibers only observed from 23.5% (w/v) PS/MEH‐PPV solution in chloroform. Improvement in the electrospinnability of 8.5% (w/v) PS/MEH‐PPV solution in chloroform was achieved by addition of an organic salt, pyridinium formate (PF), or by addition of a minor solvent with a high dielectric constant value. The average diameters of the as‐spun PS/MEH‐PPV fibers were between 0.30 and 5.11 μm. Last, photoluminescence of 8.5% (w/v) solutions of PS/MEH‐PPV in a mixed solvent system of chloroform and 1,2‐dichloroethane of various volumetric compositions and the resulting as‐spun fibers was investigated and compared. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1881–1891, 2005     

Aligned and molecularly oriented semihollow ultrafine polymer fiber yarns by a facile method

In this work, aligned and molecularly oriented bone‐like PLLA semihollow fiber yarns were manufactured continuously from an optimized homogeneous polymer‐solvent‐nonsolvent system [PLLA, CH₂Cl₂, and dimethyl formamide (DMF)] by a single capillary electrospinning via self‐bundling technique. Here, it should be emphasized that the self‐bundling electrospinning technique, a very facile electrospinning technique with a grounded needle (which is to induce the self‐bundling of polymer nanofibers at the beginning of electrospinning process), is used for the alignment and molecular orientation of the polymer fiber, and the take‐up speed of the rotating drum for the electrospun fiber yarn collection is very low (0.5 m/s). PLLA can be dissolved in DMF and CH₂Cl₂ mixed solvent with different ratios. By varying the ratios of mixed solvent system, PLLA electrospun semihollow fiber with the porous inner structure and compact shell wall could be formed, the thickness of the shell and the size of inner pores could be adjusted. The results of polarized FTIR and wide angle X‐ray diffraction investigations verified that as‐prepared PLLA semihollow fiber yarns were well‐aligned and molecularly oriented. Both the formation mechanism of semihollow fibers with core‐shell structure and the orientation mechanism of polymer chains within the polymer fibers were all discussed. The as‐prepared self‐bundling electrospun PLLA fiber yarns possessed enhanced mechanical performance compared with the corresponding conventional electrospun PLLA fibrous nonwoven membranes. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1118–1125, 2010     

Electrospinning of Chitosan

Summary: An electrospun nonwoven fabric of a cationic polysaccharide, chitosan, was successfully prepared. The present study focuses on the effect of the electrospinning solvent and the chitosan concentration on the morphology of the resulting nonwoven fabrics. The solvents tested were dilute hydrochloric acid, acetic acid, neat formic acid and trifluoroacetic acid. As the chitosan concentration was increased, the morphology of the deposition on the collector changed from spherical beads to interconnected fibrous networks. The addition of dichloromethane to the chitosan‐TFA solution improved the homogeneity of the electrospun chitosan fiber. Under optimized conditions, homogenous (not interconnected) chitosan fibers with a mean diameter of 330 nm were prepared.

Effects of the coexisting dichloromethane (MC) in the prespun chitosan‐TFA solution on the morphology of the electrospun chitosan fibers. The volume ratio of TFA:MC was 70:30 (×5 000).     

Degradable cellulose‐based polymer brushes with controlled grafting densities

Cellulose‐based polymer brushes with variable grafting densities and low dispersity were synthesized by grafting poly(n‐butyl acrylate) (PBA) side chains from cellulose‐derived backbones via ATRP. Esterification of commercially available cellulose acetate with 2‐bromoisobutyryl bromide (2‐BiBB) in NMP provided cellulose‐based macroinitiators averaging one initiation site per double glucose unit. ATRP macroinitiators averaging up to 6 initiation sites per repeating double glucose unit were prepared by acylation of microcrystalline cellulose (MCC) in LiCl/DMAc solvent system with 2‐BiBB. A series of linear macroinitiators with narrow MWD were obtained by fractional precipitation process. The content of initiating sites was determined by elemental analysis. (Meth)acrylate side chains were then grafted from the cellulose‐based macroinitiators. The prepared cellulose‐based polymer brushes showed tunable degradation rates dependent on grafting density of the brush, following two different degradation pathways, either cleavage of the main chain or detachment of the side chains. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2426–2435     

Influence of organic solvents on cutinase stability and accessibility to polyamide fibers

The stability of cutinase was measured in the presence of dimethylacetamide (DMA) and benzyl alcohol (BA). These solvents are known swelling agents of polyamide fibers. We found that cutinase retains some stability (half‐life of 14 h), enough for an enzymatic treatment with a solvent composition of 1.5% DMA + 10% BA. Enzymatic treatment in the presence of these solvent compositions yields more soluble amino groups as well as more amino end groups at the fiber level. We have shown evidence that the presence of minor quantities of solvent can increase the accessibility of the enzyme towards the polyamide fiber. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2749‐2753, 2005     

Fluorescent PMMA/MEH‐PPV electrospun nanofibers: Investigation of morphology,solvent, and surfactant effect

Electrospinning is a powerful technique to produce nanofibers of tunable diameter and morphology for medicine and biotechnological applications. By doping electrospun nanofibers with inorganic and organic compounds, new functionalities can be provided for technological applications. Herein, we report a study on the morphology and optical properties of electrospun nanofibers based on the conjugated polymer poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV) and poly(methylmethacrylate) (PMMA). Initially, we investigate the influence of the solvent, surfactant, and the polymer concentration on electrospinning of PMMA. After determining the best conditions, 0.1% MEH‐PPV was added to obtain fluorescent nanofibers. The optical characterizations display the successful impregnation of MEH‐PPV into the PMMA fibers without phase separation and the preservation of fluorescent property after fiber electrospinning. The obtained results show the ability of the electrospinning approach to obtain fluorescent PMMA/MEH‐PPV nanofibers with potential for optical devices applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1388–1394     

Rheology of cellulose/KSCN/ethylenediamine solutions and coagulation into filaments and films

Dissolution of cellulose in ethylenediamine/potassium thiocyanate (KSCN) was studied as a function of cellulose and KSCN concentration. Concentrations of up to 9% (w/w) cellulose were obtained. Large variations in solution rheology with salt and cellulose concentration were observed, and phases including flowing solutions and gels were identified visually. Rheological data indicated that viscosity decreased with increasing salt or cellulose concentration in certain composition ranges. Viscosity decrease with concentration increase is associated with either onset of liquid crystalline ordering or phase separation in the system. Both of these are quite likely in the cellulose/ethylenediamine/KSCN system, depending on composition. Additionally, comparison of loss (G′′) and storage (G′) moduli confirmed that compositions that exhibited gel behavior at zero shear became liquid at shear rates as low as 1 Hz. Solutions were coagulated into filaments and films using ethanol (CH₃CH₂OH) and methanol (CH₃OH). Infrared spectroscopy (FTIR) indicated that significant quantities of KSCN salt remained in the fibers and films after coagulation. Subsequent washing removed residual KSCN and improved physical properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2013–2022, 2005     

Solvent and concentration effects on the properties of electrospun poly(ethylene terephthalate) nanofiber mats

This study describes the preparation and characterization of nanofibrous mats obtained by electrospinning poly(ethylene terephthalate) (PET) solutions in trifluoroacetic acid/dichloromethane (TFA/DCM). Special attention was paid to the effect of polymer concentration and solvent properties on the morphology, structure, and mechanical and thermal properties of the electrospun nonwovens. The results show that the spinnable concentration of PET solution in TFA/DCM solvents is above 10 wt %. Mats have nanofibrous morphology with fibers having an average diameter in the range of 200–700 nm (depending on polymer concentration and solvent composition) and an interconnected pore structure. Higher solution concentration favors the formation of uniform fibers without beads and with higher diameter. Morphology and fiber assembly changed with the solvent properties. Solvent mixtures rich in TFA, i.e., those with higher dielectric constant and lower surface tension, originated fibers with small diameter. However, due to the lower volatility, those solvent mixtures also produced more branched and crosslinking fibers, with less morphologic uniformity. Mechanical properties (Young's modulus, ultimate strength, and elongation at break) and thermal properties (glass transition, crystallization, and melting) have been studied for the PET electrospun nanomats and compared with those of the original polymer. Solvent effect on fiber crystallinity was not significant, but a complex effect was observed on the mechanical properties of the electrospun mats, as a consequence of the different structural organization of the fibers within the mat network. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 460–471, 2008     

Silicone‐urethane membranes for lithium batteries. Part 1. Moisture‐cured poly(siloxane‐urethane‐urea) elastomers containing polyethylene oxide (PEO) segments – synthesis and characterization as potential membrane materials

Poly(siloxane‐urethane‐urea) elastomers containing both polysiloxane and polyethylene oxide (PEO) segments in the polymer chain were obtained by moisture‐curing of NCO‐terminated poly(siloxane‐urethane) prepolymers synthesized from isophorone diisocyanate and mixtures of polyoxyethylene diols and polysiloxane diols with various molecular weights. Mechanical properties of the moisture‐cured films and their swelling ability in solvent mixtures commonly used in lithium batteries were investigated, and it was found that they were greatly influenced by PEO content in the polymer. PEO content in the polymer was also found to affect very much the electric conductivity of the films after immersion in lithium salt solution in ethylene carbonate–dimethyl carbonate solvent mixture. At high contents of PEO in the polymer chain specific conductivities of the films in a range of 10^?3, Scm^?1 could be achieved at room temperature. Based on the results of Scanning Electron Microscopy with X‐ray Analysis (SEM/EDS) investigations and wide‐angle X‐ray scattering and small‐angle X‐ray scattering studies, it could be anticipated that the reason for good conductivity of the films might be their specific supramolecular structure that potentially facilitated lithium ion mobility. Copyright © 2015 John Wiley & Sons, Ltd.