温度敏感聚(N-异丙基丙烯酰胺-co-甲基丙烯酰氧乙基二甲基辛基溴化铵)水凝胶的溶胀性能研究

由于改变亲水／疏水单体比值、与离子单体共聚心、改变凝胶内部结构等均可不同程度地调整温敏水凝胶的溶胀性能,本研究选择一种既含疏水烷基又含季铵盐正离子型亲水基团的两亲性单体——甲基丙烯酰氧乙基二甲基辛基溴化铵（ADMOAB）,结构如示意图1所示．与N-异丙基丙烯酰胺（NIPAM）聚合,制备了P（NIPAM-co-ADMOAB）共聚水凝胶,以便在引入离子型结构单元的同时,改变凝胶体系中亲水／疏水单体比值,避免单纯增加疏水单体引起的水凝胶溶胀性降低问题,并考察了ADMOAB对水凝胶溶胀性能的影响,对该类水凝胶迄今鲜见相关文献报道．该研究对进一步了解水凝胶的构效关系、探索有效控制溶胀性能的途径具有积极意义．     

亲水/疏水半互穿网络凝胶在直流电场作用下的响应

研究了一种亲水 疏水型半互穿网络水凝胶 (PAAc QPVPDgels)对直流电场的刺激应答 .该凝胶中的疏水型N 十二烷基聚 (4 乙烯吡啶 )溴化盐 (QPVPD)高分子链与亲水型聚丙烯酸水凝胶 (PAAc)网络通过物理缠绕复合 .由于疏水力和亲水力的共同作用 ,在接触电场下 ,该凝胶在阳极端发生消溶胀 ,疏水相互作用对消溶胀有一定的影响 ;在非接触电场下 ,该凝胶在弱碱性溶液中迅速向阴极方向弯曲 ,在弱酸性溶液中首先发生消溶胀 ,然后向阳极方向弯曲     

含孪尾型丙烯酰胺的HAPAM在新胶束聚合体系中的制备及其疏水缔合性

以表面活性单体2-丙烯酰胺基十二烷磺酸钠(NaAMC12S)为表面活性剂构建了新的胶束共聚合体系,实施了丙烯酰胺(AM)与N,N-二正十二烷基丙烯酰胺(DiC12AM)的胶束共聚合,制备了含孪尾型丙烯酰胺的疏水缔合聚丙烯酰胺(HAPAM),该聚合物为三元共聚物DiC12AM/NaAMC12S/AM.通过控制共聚合条件,制得了微结构系列变化的共聚物;采用红外光谱法表征了三元共聚物的化学结构,用荧光探针法与表观粘度法重点研究了共聚物DiC12AM/NaAMC12S/AM的大分子链微结构与其疏水缔合性的关系.结果表明:新胶束共聚合体系大大简化了胶束的共聚合操作,而且由于表面活性单体进入共聚物主链,使三元共聚物DiC12AM/NaAMC12S/AM具有更强的疏水缔合性.与由单尾型丙烯酰胺N-正十二烷基丙烯酰胺(C12AM)为疏水单体制备的HAPAM相比,由DiC12AM制得的HAPAM疏水缔合性更为显著.     

疏水改性无规共聚物水凝胶体积相变研究

以偶氮二异丁腈(AIBN)为引发剂,合成了一系列疏水改性的甲基丙烯酸β-羟乙酯(HEMA)无规共聚物水凝胶,研究了离子强度、pH、温度等条件对凝胶体积相变的影响。结果表明,疏水基末端端基的疏水程度决定凝胶体积相变的速率,随着疏水性单体甲基丙烯酸酯烷基链的增长,凝胶的疏水性增强,凝胶的相转变pH向低pH处迁移;温度高于LCST时,分子间的氢键作用减弱,疏水基团间的相互作用加强,凝胶发生体积相变。     

有效碳链长度与脂肪醇的沸点

脂肪醇沸点(b.p.)变化规律可用下述关系式表示:ln(800.386-T~b)=6.64919-2.94828×10^-^2N~E~C~C+0.150955ΔPEI。式中N~E~C~C为醇中烷基的有效碳链长度, ΔPEI是具有相同碳原子数目的支链烷基与直链烷基的极化效应指数的差值, 它表示羟基对醇的沸点的影响。     

离子液体中AM/AMPS/N8AM三元共聚物的合成及溶液性能

以丙烯酰胺(AM)和2-丙烯酰胺基-2-甲基丙磺酸(AMPS)为亲水单体, 以N-辛基丙烯酰胺(N8AM)为疏水单体, 在离子液体[bmim]BF4中实现了疏水缔合丙烯酰胺三元共聚物的合成.     

疏水缔合型丙烯酰胺类聚合物Ⅰ.疏水单体N-苯基甲酰胺-丙烯酰胺的合成与表征

通过异氰酸苯酯和丙烯酰胺(AM)的取代反应,制备了疏水缔合型单体N-苯基甲酰胺-丙烯酰胺(HMAM)。用红外光谱、核磁共振氢谱、质谱、元素分析和差示扫描量热仪对HMAM进行表征。结果表明,HMAM单体含有疏水和亲水基团,可用于制备新型水溶性疏水缔合型聚合物,该聚合物不溶于水和丙酮等强极性溶剂,但能溶于二甲亚砜和N,N-二甲基甲酰胺等中等极性的溶剂中。     

亲水链段长度对液晶模板水凝胶形态和温敏性的影响

采用疏水烷基(C16H33)相同而亲水的聚氧乙烯链(CH2CH2O)n=2,10,20长度不同的表面活性剂苄泽(Brij 52/56/58)作为模板制备得到3种孔洞尺寸为5～80μm的聚异丙基丙烯酰胺水凝胶(HNB).研究表明,n值越小,疏水性越大.15 wt%浓度下,不同n值的Brij水溶液均呈现明显的液晶织构.在t=4和7 min时HNB58和HNB56凝胶预聚液的透光率迅速下降至3.3～3.5,而HNB52凝胶预聚液的透光度一直保持在3.5.以n=20的Brij 58作为模板制备的HNB58凝胶孔洞数量多,尺寸为5～10μm.以n=2的Brij52为模板制备的HNB52凝胶孔洞形态呈层状,溶胀度最小,为6.9 g/g.而以n=10的Brij56为模板制备的HNB56凝胶孔洞呈蜂窝状,尺寸最大,为40～80μm,溶胀度最高,为7.9 g/g,37℃下20 min时HNB56失水超过80%.由于模板的作用,n值的变化并没有改变HNB凝胶的体积相转变温度(VPTT≈33℃),但吸热峰面积变宽.     

疏水缔合聚丙烯酰胺的合成及溶液性能研究

水溶性疏水缔合聚合物是在聚合物亲水主链上引入极少量疏水基团(一般小于2ｍｏｌ%)而形成的一种新型水溶性聚合物[1]。由于这类聚合物具有独特的流变性能,因而备受学术界和工业界关注。目前已作为涂料增稠剂[2]和流变改性剂[3]得到了应用,而通过在部分水解聚丙烯酰胺(ＨＰＡＭ)的亲水主链上引入少量疏水单体而形成的疏水缔合聚丙烯酰胺(ＨＡＰＡＭ)则可望克服ＨＰＡＭ耐温、耐盐性差的缺陷[4]而作为新一代水溶性聚合物材料用于油气开采作业[5,6]。由于亲水单体和疏水单体的不相容性,通常通过在反应溶液中加入表面活性剂使亲水单体和疏水单体…     

AM/DMC/C11AM疏水缔合聚两性电解质的合成、表征与溶液性质

通过Ritter反应合成弱阴离子型疏水单体丙烯酰胺基十一烷基酸(C11AM). 以丙烯酰胺(AM)、甲基丙烯酰氧乙基三甲基氯化铵(DMC)和丙烯酰胺基十一烷基酸(C11AM)为原料, 在水介质中合成新型疏水缔合聚两性电解质AM/DMC/C11AM. 利用1H NMR确证了疏水单体和共聚产物的分子结构. 流变性和芘荧光探针的研究结果表明, AM/DMC/C11AM系列疏水缔合聚两性电解质由于兼具疏水缔合性质和反聚电解质效应, 使其具有较好的耐盐性能.     

Mechanical Properties and Network Structure of Hydrophobic Association Hydrogels Prepared from Octylphenol Polyoxyethylene(7) Acrylate and Sodium Dodecyl Sulfate

Hydrophobic association hydrogels(HA-gels) with high mechanical strength were prepared by free radical micellar copolymerization in aqueous solutions of acrylamide(AM), anion surfactant sodium dodecyl sulfate(SDS) and a small amount of hydrophobic monomer octylphenol polyoxyethylene(7) acrylate(OP-7-AC). We found that the molar ratio of SDS to OP-7-AC has a great effect on the tensile strength and other mechanical property parameters. The best ratio point R' was determined. On the basis of Mooney theory and statistical theory, the critical tensile ratios and critical tensile strengths of the hydrogels were obtained, elastic parameters C₁ and C₂ were calculated via uniaxial tensile equation and structural parameters, such as the effective network chain density and the averaged molecular weight of the chain between cross-linking points of all the hydrogels were evaluated. The results indicate that the variation of mechanical property parameters depends on the number of effective cross-linking points and the match degree of long and short chains.     

Formation Mechanism and Tensile Mechanical Properties of Poly(acrylamide-co-octylphenol polyoxyethylene (10) acrylate) Hydrophobic Association Hydrogels With High Toughness

Poly(acrylamide-co-octylphenol polyoxyethylene (10) acrylate) hydrophobic association hydrogels, which is abbreviated to poly(AM-co-OP10/AC) HA-gels, were prepared through micellar copolymerization of acrylamide (AM) and a small amount of octylphenol polyoxyethylene (10) acrylate (OP10/AC) in the presence or absence of sodium dodecyl sulfate (SDS). For poly(AM-co-OP10/AC) HA-gels, formation mechanism was discussed in detail, which can reasonably explain the reason that tensile mechanical properties of the hydrogels (containing SDS) are much higher than those of the hydrogels (not containing SDS). In addition, according to the tensile experimental results of poly(AM-co-OP10/AC) HA-gels, the effect of composition content in the initial solutions on tensile mechanical properties was investigated in detail. The results clearly indicate tensile strength, elastic modulus and elongations for poly(AM-co-OP10/AC) HA-gels strongly depended on composition content in the initial solutions.     

Preparation and properties of physically and chemically cross-linked hybrid hydrophobic association hydrogels with good mechanical strength

To correct the defects of hydrophobic association hydrogels(HA-gels), new physically and chemically cross-linked hybrid hydrophobic association hydrogels(hybrid HA-gels) were prepared by radical copolymerization of acrylamide(AM), octylphenol polyoxyethylene(n) acrylate(OPn AC, n stands for the number of ethoxy group, and is 10 and 21) and N,N′-methylenebisacrylamide(MBA). On the basis of the statistical molecular theory of rubber elastic, the Mooney-Rivlin model and using the tensile true stress(σ_true) tested at room temperature, the number of network strands per unit volume(υ_0) and the number-average molar mass of a network strand(M_c) were evaluated for hybrid HA-gels. For the hydrogels, the effect of the content of MBA and OP10 AC on their tensile mechanical properties was studied by using υ_0 and M_c; also, the effect of the compositions and temperature on their swelling behavior in distilled water was discussed in detail. In addition, hybrid HA-gels including a small quantity of MBA possessed the capabilities of secondary self-healing and remolding. In contrast with HA-gels prepared by the same compositions besides MBA, hybrid HA-gels showed good mechanical strength and long-term thermal stability in distilled water in the range of 25 to 80 °C. Furthermore, hybrid HA-gels also avoided the self-deswelling behavior of HA-gels. The results show that the application fields of HA-gels will be greatly broadened after introducing a chemical cross-linking network.     

Tensile Mechanical Properties of Hydrophobic Association Hydrogels: Effect of Crosslinking Method,Synthesis Temperature,Mineral Salt and Swelling

Hydrophobic association hydrogels (HA-gels) were prepared through micellar copolymerization of acrylamide (AM) and a small amount of octylphenol polyoxyethylene acrylate (OP-10-AC) in an aqueous solution containing sodium dodecyl sulfate (SDS). For the P(AM/OP-10-AC) HA-gels, the effect of crosslinking method, synthesis temperature, mineral salt (NaCl) and swelling on their tensile mechanical properties was investigated in detail. The experimental results show that crosslinking method, synthesis temperature, NaCl and swelling powerfully influenced tensile mechanical properties of the P(AM/OP-10-AC) HA-gels. In addition, according to the tensile experimental results of the P(AM/OP-10-AC) HA-gels swollen, an effective crosslinking density change model is proposed. The effect of swelling on tensile mechanical properties of the P(AM/OP-10-AC) HA-gels was discussed on the basis of the model.     

高强度疏水缔合水凝胶的交联网络结构形成机理

高强度疏水缔合水凝胶(HA-gels)是丙烯酰胺(AM)和少量的疏水单体辛基酚聚氧乙烯(4)醚丙烯酸酯(OP-4-AC)在十二烷基硫酸钠(SDS)水溶液中采用胶束共聚的方法制备的.采用胶束共聚理论、橡胶弹性统计理论及Mooney-Rivlin理论,并结合单向拉伸实验数据,对HA-gels的交联网络结构的形成机理进行了探...     

高分子量的枝状聚硅烷的合成与表征

根据硅氢加成反应机理设计了“顺点滴式”工艺 ,高效、低耗地合成了甲基苯乙基二氯硅烷和甲基正己基二氯硅烷 .根据Wurtz还原偶联反应原理 ,采用“预聚”和“混聚”两种工艺分别合成枝状共聚硅烷 ,发现运用“预聚”工艺可以合成分子量很高的枝状聚硅烷 .     

Gemini阳离子表面活性剂的合成及其胶束生成 Gemini阳离子表面活性剂的合成及其胶束生成

Cationic Gemini surfactants, alkanediyl-α,ω-bis(dimethyldodecylammonium bromide) have been synthesized by the following method: firstly dodecyl bromide was prepared by the reaction of dodecanol with bromic acid in the presence of strong sulfuric acid. Dodecylbromide was then reacted with N,N-tetramethyl ethane diamine(or N,N-tetramethyl hexana diamine) to prepare the title-compounds. Micellization of these Gemini surfactants was investigated using conductivity measurement. The results showed that the critical micelle concentration(cmc) of the Gemini surfactants has a much lower value compared with that of the corresponding “ monomer” . For a series of the Geminis with the same length(s) in the spacer chain, the cmc decreased with increasing the carbon number (m) in the alkyl chain. The aggregation number(N) of the micelle also drastically decreased with m. For the same value of m, the cmc varied slightly with s, which indicated that the electrostatic interaction between the ionic-groups of the “ monomer” has been naturally changed duo to a link between the two ionic-groups of the “ monomer” through a spacer. However, N was strongly decreased with s,which may be a reason of steric inhibition coming from the ionic-groups due to a link of spacer. With increasing temperature, micellization of the Gemini surfactants was slightly enhanced.     

Self‐controlled synthesis of hyperbranched poly(ether‐ketone)s from A2 + B3 approach in poly(phosphoric acid)

Self‐controlled synthesis of hyperbranched poly(ether‐ketone)s (HPEKs) were prepared from “A₂ + B₃” approach by using different monomer solubility in reaction medium. 1,3,5‐Triphenoxybenzene as a hydrophobic B₃ monomer was reacted with commercially available terephthalic acid or 4,4′‐oxybis(benzoic acid) as a hydrophilic A₂ monomer in a hydrophilic reaction medium, polyphosphoric acid (PPA)/phosphorous pentoxide (P₂O₅). The resultant HPEKs were soluble in various common organic solvents and had the weight‐average molecular weight in the range of 3900–13,400 g/mol. The results implied that HPEKs were branched structures instead of crosslinked polymers. The molecular sizes and shapes of HPEKs were further assured by morphological investigation with scanning electron microscopy (SEM) and atomic force microscopy (AFM). Hence, the applied polymerization condition was indeed strong enough to efficiently facilitate polycondensation via “direct” Friedel‐Crafts reaction without gelation. It could be concluded that the polymer forming reaction was kinetically controlled by automatic and slow feeding of the hydrophobic B₃ monomer into the hydrophilic reaction mixture containing hydrophilic comonomer. As a result, hyperbranched structures were formed instead of crosslinked polymers even at full conversion (equifunctional monomer feed ratio). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3326–3336, 2009     

Microcalorimetric study on micellization of nonionic surfactants with a benzene ring or adamantane in their hydrophobic chains

The micellization of a novel family of nonionic surfactants poly(oxyethylene) glycol alkyl ethers has been studied by microcalorimetry. One of the surfactants has adamantane, and the other nonionic surfactants have a benzene ring in their hydrophobic chains, which moves from the terminal of the hydrophobic chain toward the headgroup. Moreover, the alkyl chain of the nonionic surfactants is straight or branched. Both the critical micelle concentration (cmc) and the thermodynamic parameters associated with the micelle formation have been obtained. The cmc decreases and the enthalpy of micelle formation (deltaH(mic)) becomes less positive gradually as the length of hydrophobic chain increases, whereas the values of cmc and deltaH(mic) tend to increase for the surfactants with a longer ethylene oxide chain. However, the deltaH(mic) value of the surfactant with seven carbon atoms in a hydrophobic chain is more positive than that of the surfactant with six carbon atoms in a hydrophobic chain. Comparing with the nonionic surfactant with a methylene hydrophobic chain, the surfactants with benzene rings and adamantane groups have larger cmc values and the cmc values increase with the size of the groups. Furthermore, moving the phenyl group from the terminal of the hydrophobic chain to the neighbor of the hydrophilic headgroup leads to the decreased cmc. Both the variation of hydrophobic interaction from the movement of phenyl group and pi-pi interaction among adjacent phenyl groups affect deltaH(mic) values.     

铁系亚胺基吡啶复配催化乙烯原位共聚产物的表征

Branched polyethylene from ethylene as single monomer was prepared by the tandem catalyst system of {2-[2-Me C6 H4 N=Me)]2 C5H3N} FeCl2 (1) and {2,6-[1-(2,6-Me2-4-Br-C6H4N=(Me)]2C5H3N} FeCl2 (2) activated with methylaluminoxane (MAO) . The products of polymerization were characterized by DSC, GPC and ^13C-NMR. The results revealed that the copolymer produced by in situ copolymerization of ethylene was a mixture of branched polyethylene and α-olefin. The content of α-olefin in the mixture was increased with increasing the molar ratio of catalysts 1/2. The MWD paramelers of polyethylene and copolymer were 28.6 and 7.9, respectively. ^13C-NMR spectra showed that there were ethyl groups, butyl groups and long chain alkyl groups in the copolymer. The average degree of branching of such branched polyethylene was less than 5C/1000C.