Ag2S quantum dot-sensitized solar cells

We present a new photosensitizer – Ag₂S quantum dots (QDs) – for solar cells. The QDs were grown by the successive ionic layer adsorption and reaction deposition method. The assembled Ag₂S-QD solar cells yield a best power conversion efficiency of 1.70% and a short-circuit current of 1.54 mA/cm² under 10.8% sun. The solar cells have a maximal external quantum efficiency (EQE) of 50% at λ = 530 nm and an average EQE of ～ 42% over the spectral range of 400–1000 nm. The effective photovoltaic range covers the visible and near-infrared spectral regions and is ～ 2–4 times broader than that of the cadmium chalcogenide systems — CdS and CdSe. The results show that Ag₂S QDs can be used as a highly efficient and broadband sensitizer for solar cells.     

Chemical bath deposition of CdS quantum dots on vertically aligned ZnO nanorods for quantum dots-sensitized solar cells

Formation of CdS quantum dots (Q dots) on the vertically aligned ZnO nanorods electrode was carried out by chemical bath deposition. The diameter and thickness of ZnO nanorods are ～100–150 nm and ～1.6 μm, respectively, and CdS Q dots on ZnO nanorods have a diameter of smaller than 15 nm. In application of the Q dots-sensitized solar cells, composite film exhibited a power conversion efficiency of 0.54% under air mass 1.5 condition (80 mW/cm²), and incident-photon-to-current conversion efficiency showed 18.6%.     

Metal-free organic dyes with benzothiadiazole as an internal acceptor for dye-sensitized solar cells

We synthesized three metal-free organic dyes (H11–H13) consisting of a 3,6-disubstituted carbazole, benzothiadiazole, and cyanoacrylic acid. All the dyes exhibited high molar extinction coefficients and suitable energy levels for electron transfer from the electrolyte to the TiO₂ nanoparticles. Under standard AM 1.5G solar irradiation, the device using dye H13 with co-adsorbed chenodeoxycholic acid (CDCA) displayed the best performance: an open-circuit voltage (V_oc) of 0.71 V, a short-circuit current density (J_sc) of 12.69 mA cm⁻², a fill factor (FF) of 0.71, and a power conversion efficiency (PCE) of 6.32%. The PCE was ∼79% of that for commercially available N719 cells (8.02%) under the same conditions.     

Magnesium doped ZnO nanoparticles embedded ZnO nanorod hybrid electrodes for dye sensitized solar cells

We report a novel type of Mg doped ZnO nanoparticles (ZMP) embedded on hydrothermally grown ZnO nanorod (ZR) based photoanode dye sensitized solar cells. The crystallinity, composition and morphology of the photoanodes were characterized by using X-ray diffraction analysis, X-ray photoelectron spectroscopy and scanning electron microscopy. The amount of dye absorbed in the photoanode was observed using UV visible spectral analysis. The improved internal resistance and charge-transfer kinetics of the fabricated cells were analyzed using electrochemical impedance spectroscopy. The ZMP embedded electrode of low thickness (~2.5 μm) gained an enhanced short-circuit current density of 8.56 mA/cm², open-circuit photo voltage of 0.71 V, fill factor of 0.51, and overall conversion efficiency of 2.91 % under 1 sun illumination. This shows high conversion efficiency and performance than that of ZnO nanorod (η ~ 0.22 %) and bare ZnO nanoparticles (ZP) embedded ZnO nanorod (η ~ 1.04 %) based cells. The presence of Mg ions in the ZnO nanoparticle hinders the interfacial recombination of the photo-excited electrons with the electrolyte and also shows better dye absorption than that of ZR. These factors can significantly enhance solar-cell performance and increase the efficiency of the ZMP based dye sensitized solar cells.     

Electrophoretic deposition of ZnO photoanode for plastic dye-sensitized solar cells

Plastic dye-sensitized solar cells have been fabricated based on an organic dye (D 149) and ZnO photoanode prepared via room temperature electrophoretic deposition (EPD) to yield a conversion efficiency of 4.17% under 100 mW cm^?2 AM 1.5 illumination. Intensity modulated photocurrent spectroscopy analyses reveal that the fabricated ZnO electrodes have adequate interparticle connection, even in the absence of any post-treatment. This study demonstrates that EPD is a convenient method for photoanode fabrication and ZnO photoelectrodes obtained via EPD are promising for efficient plastic solar cells.     

A two-step method combining electrodepositing and spin-coating for solar cell processing

Electrochemistry provides a simple and promising method for preparing organic solar cells (OSCs). In this paper, we present a two-step solution-based method to prepare bilayer heterojunction OSCs by electrodepositing polythiophene (PTh) and then spin-coating chloroform solution of [6,6]-phenyl C61-butyric acid methyl ester (PCBM) onto the PTh layer. The influence of film thickness on performance of bilayer solar cells was investigated, and the best performance was achieved when the thickness of PTh and PCBM was 15 nm and 30 nm, respectively. The optimized solar cell showed power conversion efficiency of 0.1% under the illumination of AM 1.5 (100 mW cm⁻²) simulated solar light. This solution-based method offers a new way for processing bilayer OSCs.     

Study on the fabrication and photovoltaic property of TiO2 mesoporous microspheres

Titanium dioxide mesoporous microspheres with high surface area was successfully prepared by a facile one-step hydrothermal approach using polyethylene glycol (PEG, MW 200) as the soft template. Study shows that ∼15 nm TiO₂ nanoparticles was assembled into ∼1.1 μm mesoporous microspheres. The Brunauer-Emmett-Teller surface area of TiO₂ microsphere is up to 137 m²/g. TiO₂ mesoporous microspheres were fabricated onto the surface of fluorine-doped tin oxide glass and used as the photoanode of dye-sensitized solar cells, which exhibits an open circuit photovoltage of 0.80 V and an overall conversion efficiency of 6.6%. Owing to the enhanced dye loading and light-harvesting efficiency, a 26% improvement in the overall conversion efficiency was achieved when compared with the commercial Degussa P₂₅ nanoparticles.     

Large area,waterproof, air stable and cost effective efficient perovskite solar cells through modified carbon hole extraction layer

The conventional unstable and expensive hole transporting materials (HTM) has been replaced by cost effective modified carbon hole extraction layer. Herein, we demonstrated a new recipe toward air stable and waterproof modified carbon hole extraction layer for efficient perovskite solar cells (PSCs). The commercial available carbon ink modified with methylammonium lead iodide (MAI) has been used as hole extraction layer for ambipolar perovskite solar cells. The fabricated optimized perovskite solar cell having Glass/FTO/mp-TiO₂/MAPbI_3-xCl_x/carbon + MAI/Carbon configuration exhibited η = 13.87% power conversion efficiency (PCE) with open circuit voltage (V_OC) 0.997 V, current density (J_SC) = 21.41 mAcm^?2 and fill factor (FF) 0.65. Furthermore, the air stability were tested at room temperature in open atmosphere. The water proof stability was tested under water flushing. Our results revealed that, although our carbon based devices show lower PCE (η = 13.87%) compared to spiro-MeOTAD HTM (η = 15%), the fabricated PSCs could even retain >90% after water exposure >20 times and ambient air stability more than 160 days. Further the large area device (>1 cm²) device shows 13.04% PCE with Jsc = 21.47 mAcm^?2, V_OC = 0.996 V and FF = 0.61. We have also demonstrated >13% efficiency for large area device (>1.1 cm²), demonstrating that the developed method is simple, cost effective and promising towards large area device fabrication. The developed methodology based on low cost carbon hole extraction layer will be helpful towards waterproof and air stable perovskite solar cells for large-area devices.     

A novel composite polymer electrolyte containing room-temperature ionic liquids and heteropolyacids for dye-sensitized solar cells

A novel composite polymeric gel comprising room-temperature ionic liquids (1-butyl-3-methyl-imidazolium-hexafluorophosphate, BMImPF₆) and heteropolyacids (phosphotungstic acid, PWA) in poly(2-hydroxyethyl methacrylate) matrix was successfully prepared and employed as a quasi-solid state electrolyte in dye-sensitized solar cells (DSSCs). These composite polymer electrolytes offered specific benefits over the ionic liquids and heteropolyacids, which effectively enhanced the ionic conductivity of the composite polymer electrolyte. Unsealed devices employing the composite polymer electrolyte with the 3% content of PWA achieved the solar to electrical energy conversion efficiency of 1.68% under irradiation of 50 mW cm⁻² light intensity, increasing by a factor of more than three compared to a DSSC with the blank BMImPF₆-based polymer electrolyte without PWA. It is expected that these composite polymer electrolytes are an attractive alternative to previously reported hole transporting materials for the fabrication of the long-term stable quasi-solid state or solid state DSSCs.     

Organic dyes with a novel anchoring group for dye-sensitized solar cell applications

Two novel trialkylsilyl-containing organic sensitizers (JK-53 and JK-54) have been designed and synthesized. Nanocrystalline TiO₂–silica-based dye-sensitized solar cells (DSSCs) were fabricated using these dyes. Under standard global AM 1.5 solar conditions, the JK-53-sensitized cell gave a short-circuit photocurrent density (J_sc) of 6.37 mA cm^?2, an open-circuit voltage (V_oc) of 0.70 V, and a fill factor of 0.74. These values correspond to an overall conversion efficiency (η) of 3.31%. By comparison, the JK-54-sensitized cell resulted in a J_sc of 7.52 mA cm^?2, a V_oc of 0.71 V, and a fill factor of 0.75. These values give an overall conversion efficiency of 4.01%.     

Amphiphilic ruthenium dye as an ideal sensitizer in conversion of light to electricity using ionic liquid crystal electrolyte

The optimization of interfacial charge transfer between the dye and the electrolyte is crucial to the design of dye-sensitized solar cells. In this paper, we address the combined use of an ionic liquid crystal electrolyte and amphiphilic ruthenium dyes in dye-sensitized solar cells. The solar cell with an amphiphilic ruthenium dye [Ru(H₂dcbpy)(tdbpy)(NCS)2] (H₂dcbpy = 4,4′-dicarboxy-2,2′-bipyridine, tdbpy = 4,4′-tridecyl-2,2′-bipyridine), exhibited a short-circuit photocurrent density of 9.1 mA/cm², an open-circuit voltage of 665 mV and a fill factor of 0.58, corresponding to an overall conversion efficiency of 3.51%. We find that increasing dye alkyl chain length to octadecyl from tridecyl results in lower short-circuit photocurrent density and open-circuit voltage, and the suitable dyes for ionic liquid crystal electrolyte differed completely from those used in liquid and ionic liquid electrolyte cells.     

Synthesis of copolymer electrolytes based on polysiloxane and their high temperature durability analysis for solvent-free dye-sensitized solar cells

The present work develops a new type of solvent-free copolymer electrolyte based on polysiloxane for dye-sensitized solar cells (DSSCs). The electrolyte is characterized by conductivity measurements, hydrogen-1 nuclear magnetic resonance spectroscopy, rheology, and DSSC performance. Repeated units of the ethylene oxide on methylhydrosiloxane show plasticizing effects and enhanced durability of the DSSCs. DSSC employing the polysiloxane electrolytes show no energy conversion efficiency decay after 16 days test at room temperature and yields a conversion efficiency of 1.5% during long-term stability measurement at 90 °C under white light irradiation of 100 mW cm⁻². The new solvent-free polysiloxane copolymer electrolyte can be good candidate for next generation DSSC.     

Quasi-solid-state dye-sensitized solar cells assembled with polymeric ionic liquid and poly(3,4-ethylenedioxythiophene) counter electrode

Poly(3,4-ethylenedioxythiophene) nanofibers (PEDOT-NF) with high catalytic activity were synthesized and employed as a counter electrode in dye-sensitized solar cells (DSSCs). A polymeric ionic liquid (PIL) was used as a gelling agent and an iodide source for making a highly conductive gel polymer electrolyte. A quasi-solid-state DSSC assembled with this PIL-based gel polymer electrolyte and PEDOT-NF counter electrode exhibited high conversion efficiency of 8.12% at 100 mW cm^− 2.     

Synthesis of new truxene based organic sensitizers for iodine-free dye-sensitized solar cells

Developing arylamine photosensitizers with high extinction coefficients, proper electronic structures, and steric properties is warranted for the dye-sensitized solar cells (DSCs) employing iodine-free redox shuttles. Two new organic sensitizers (M21 and M22) featuring unsymmetrical truxene-based triarylamine donor have been synthesized and compared to its reference sensitizer M4. The effects of unsymmetrical truxene-based triarylamine donors were investigated by their absorption spectra, electrochemical and photovoltaic properties. The incorporation of strong electron donor unit (i.e., dipropylfluorene and 4-methoxybiphenyl) has resulted in an improved light harvesting capacity, and thus photocurrent as well as efficiency of cells. M22 sensitized DSCs employing the Co(II/III)tris(1,10-phenanthroline)-based redox electrolyte affords a short circuit photocurrent of 13.1 mA cm⁻², an open circuit voltage of 861 mV, and a fill factor of 0.70, corresponding to an overall conversion efficiency of 7.89% under standard AM 1.5 sunlight.     

Spectral broadening in quantum dots-sensitized photoelectrochemical solar cells based on CdSe and Mg-doped CdSe nanocrystals

In order to absorb a broad spectrum in visible region, a co-sensitized TiO₂ electrode was prepared by CdSe and Mg-doped CdSe quantum dots (Q dots). The power conversion efficiency of the co-sensitized Q dots photoelectrochemical solar cells (PECs) showed 1.03% under air mass 1.5 condition (I = 100 mW/cm²), which is higher than that of individual Q dots-sensitized PECs. The incident-photon-to-current conversion efficiency of the co-sensitized PECs showed absorption peaks at 541 and 578 nm corresponding to the two Q dots and displayed a broad spectral response over the entire visible spectrum in the 500–600 nm wavelength domains.     

A new photoanode architecture of dye sensitized solar cell based on ZnO nanotetrapods with no need for calcination

We introduce a photoanode architecture in dye sensitized solar cell comprising building blocks of ZnO nanotetrapods with a mean arm diameter of 40 nm and arm lengths of 500–800 nm. This photoanode features a decent roughness factor up to 400, good network forming ability and limited electron-hopping interjunctions. Even without calcination, a power conversion efficiency up to 3.27% (under 100 mW cm^?2) has been achieved at a film thickness of 31.2 μm. The avoidance of the calcination step is an outstanding feat for flexible solar cells. We have also employed impedance spectroscopy to interpret the solar cell performance features.     

Incorporation of liquid crystalline triphenylene derivative in bulk heterojunction solar cell with molybdenum oxide as buffer layer for improved efficiency

We report efficient bulk heterojunction solar cells fabricated by inserting a discotic triphenylene derivative into poly (3-hexylthiophene): [6, 6]- phenyl-C61-butyric acid methyl ester. A layer of molybdenum oxide was inserted between anode and active layer. Power conversion efficiency of 2.0% was achieved for these photovoltaic solar cells containing self-organised discotic liquid crystals in the active layer under one sun condition. The influence of varying the thickness of liquid crystal layer and annealing on these solar cells was also studied. Post annealing the bulk heterojunction devices with discotic liquid crystal layer of thickness 20 nm in them yielded an open circuit voltage of 0.41 V, short circuit current density of 17.0 mA cm^?2, a Fill factor of 0.35 and power conversion efficiency of 2.5%.     

Application of monodisperse TiO2 nanoparticles with the size of 8–10 nm in dye-sensitized solar cells

In this paper, the commercial monodisperse TiO₂ nanoparticles with the size of 8–10 nm were successfully applied to the photoelectrode for dye-sensitized solar cells (DSCs) and the influence of the thickness of the TiO₂ thin films on the photovoltaic performance of the DSCs was investigated. The result revealed that the DSCs with the TiO₂ thin film thickness of 3.6, 8.0, 11.6 and 20.0 μm gave the photoelectric conversion efficiency of 3.67%, 5.92%, 6.71% and 7.03%, respectively, under the illumination of simulated AM 1.5 sunlight (100 mW cm⁻²).     

Synthesis and photovoltaic properties of new [1,2,5]thiadiazolo[3,4-c]pyridine-based organic Broadly absorbing sensitizers for dye-sensitized solar cells

In this paper, by introducing [1,2,5]thiadiazolo[3,4-c]pyridine (PT) as an auxiliary acceptor into the molecular design of organic sensitizers, we have synthesized four new dyes (PT1–PT4) for dye-sensitized solar cells (DSSCs) with triphenylamine or N,N-diphenylthiophen-2-amine as the donor units and thiophene or benzene as the π-bridges, respectively. All the structures, optical and electrochemical properties were fully characterized. Nanocrystalline TiO₂ dye-sensitized solar cells were also fabricated using these dyes. Among them, PT2-based DSSCs showed the highest overall conversion efficiency of 6.11% with V_oc=668 mV, J_sc=12.61 mA cm⁻² and a fill factor (FF)=0.74 after a chenodeoxycholic acid (CDCA) treatment under standard illumination condition (100 mW cm⁻² simulated AM 1.5 solar light).