基于量子点涂料的柔性光阳极及碳基对电极的制备和优化

首先制备出量子点（QDs）/TiO₂涂料,分别采用丝网印刷法与刀刮法将涂料涂覆于ITO/PET柔性基底上,结果表明刀刮法制备量子点敏化太阳电池（QDSCs）效果更佳,且具有普适性。基于铜片对电极所组装的ZnCuInSe,CdSe和CdSeTe量子点半柔性QDSCs最高效率分别达2.83%,2.46%和1.99%。另外,我们对石墨纸进行表面化学修饰以提高亲水性,再通过简单的连续离子交换吸附法（SILAR）在石墨纸上负载Cu_xS纳米粒子,制备出Cu_xS/GP柔性对电极,进一步组装成全柔性QDSCs,获得了2.13%光电转化效率。     

铜锌锡硫的合成及其光电应用

铜锌锡硫(CZTS)半导体常作为对电极材料被应用于量子点敏化太阳能电池(QDSCs)中,然而效率一直低于4%。本文采用热注入法合成出纳米尺寸的CZTS并制成对电极(CZTS/FTO),用其组装的CdSe QDSCs和CdSeTe QDSCs的效率(PCE)分别达到了5.75%和7.64%。电化学阻抗谱、塔菲尔极化等表征证明电池效率的提高与CZTS良好的导电性及催化活性联系密切。     

铜锌锡硫的合成及其光电应用

铜锌锡硫(CZTS)半导体常作为对电极材料被应用于量子点敏化太阳能电池(QDSCs)中,然而效率一直低于4%。本文采用热注入法合成出纳米尺寸的CZTS并制成对电极(CZTS/FTO),用其组装的Cd Se QDSCs和Cd Se Te QDSCs的效率(PCE)分别达到了5.75%和7.64%。电化学阻抗谱、塔菲尔极化等表征证明电池效率的提高与CZTS良好的导电性及催化活性联系密切。     

量子点敏化太阳能电池研究进展

量子点敏化太阳能电池(QDSCs)因其制备成本低、工艺简单及量子点(QDs)本身的优异性能(如尺寸效应、多激子效应)等优点,近年来受到广泛关注。在此类电池中,无机半导体量子点敏化剂作为吸光材料,其自身的光电性质、制备方法、表面缺陷、化学稳定性及其在TiO₂光阳极上的敏化方法等是影响电池性能的关键。本文综述了无机半导体量子点敏化剂(包括窄带隙二元量子点、多元合金量子点及Type-Ⅱ核壳量子点)的最新研究进展,重点介绍了胶体量子点的制备方法;分类阐释了量子点在TiO₂光阳极表面的沉积与敏化方法,特别是双官能团辅助自组装吸附法;总结了针对提高电子注入效率和减少复合的量子点表面修饰方法;最后简要介绍了QDSCs的电解质和对电极的研究进展。     

花状硫化铜的合成及其光电催化性能

通过硫化介孔Cu_2O微球得到花状Cu_xS纳米催化材料,并采用丝网印刷法制备出Cu_xS/FTO对电极。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等表征手段对所得材料的结构和形貌进行了探究,同时系统考察了溶液浓度、硫化时间、催化剂印刷层数对Cu_xS/FTO电极的催化性能影响和所组装量子点敏化太阳电池的光电转换效率,其中基于Zn-Cu-In-Se量子点敏化的电池转换效率达8.80%,表现出花状Cu_xS优异的光电催化性能。     

基于新型量子点荧光微球的氯霉素免疫层析试纸条的制备和应用

以羧基化CdTe/ZnSe量子点荧光微球为标记物,通过1-乙基-(3-二甲基氨基丙基)碳二亚胺/N-羟基琥珀酰亚胺(EDC/NHS)活化法将氯霉素(CAP)单克隆抗体与量子点荧光微球偶联制备荧光探针.氯霉素全抗原(CAP-HS-BSA)及羊抗鼠二抗分别喷涂硝酸纤维素膜,形成检测线(T线)和质控线(C线),组装成新型氯霉素量子点荧光微球免疫层析试纸条,建立了快速、定量检测牛奶中CAP的方法.本研究开发的量子点荧光微球试纸条可在15 min内完成牛奶样品中CAP的定量检测,线性范围为0.1~100.0μg/L,检出限为0.1μg/L.牛奶样品CAP的加标回收率为93.3%~97.9%,相对标准偏差在4.9%~6.9%之间.     

高性能量子点编码磁性微球的制备

基于改进的层层组装法,以氯仿/正丁醇混合溶液作为反应溶剂,将油溶性CdSSe/ZnS量子点装载到表面氨基修饰的磁性聚苯乙烯微球(MS)表面,通过调节量子点浓度,制备出高性能CdSSe/ZnS量子点编码磁性微球(CdSSe/ZnS-MBs).研究了氯仿和氯仿/正丁醇混合溶液对CdSSe/ZnS-MBs制备效果的影响.结果表明,氯仿/正丁醇混合溶液不仅能避免氯仿等量子点良溶剂对聚合物微球的形貌破坏,同时能促进CdSSe/ZnS量子点高效地装载到磁性微球表面.所制备的CdSSe/ZnS-MBs在水相具有较好的分散性,荧光强度变异系数(CV)小,形貌均一.该方法为简单、精确可控地制备高编码容量的量子点编码微球提供了新思路.     

碳纳米管负载纳米金-石墨烯量子点修饰电极电化学检测过氧化氢

采用过氧化氢刻蚀法制备石墨烯量子点(GQDs),再采用原位化学还原法制备金纳米粒子-石墨烯量子点纳米复合物(Au NPs-GQDs),最后以聚二甲基二烯丙基氯化铵(PDDA)为交联剂将上述纳米复合物组装于多壁碳纳米管表面,制得金纳米粒子-石墨烯量子点-PDDA-多壁碳纳米管复合材料(Au NPs-GQDsPDDA-MWCNTs)。通过荧光光谱法、紫外-可见吸收光谱法和透射电子显微镜对上述复合材料进行表征。采用滴涂法制得该复合材料修饰的玻碳电极,研究了过氧化氢在该电极上的电化学行为。结果表明:在石墨烯量子点、金纳米粒子和多壁碳纳米管三者的协同作用下,该电极对过氧化氢的电氧化表现出强的催化活性。在优化条件下,安培法检测H_2O_2的线性范围为2.0×10~(-8)~1.5×10~(-3)mol/L,检出限(3sb)为8.0×10~(-9)mol/L,灵敏度为61.6μA/(mmol·L~(-1))。     

大尺寸石墨烯量子点组装体的制备及电化学发光性能

对氧化石墨烯纳米材料进行HNO₃氧化处理, 制备了水溶性好且具有强电化学发光(ECL)活性的大尺寸石墨烯量子点组装体(Large-sized graphene quantum dot assemblies, LSGQD-NAs). 利用透射电子显微镜(TEM)、 原子力显微镜(AFM)、 傅里叶变换红外光谱(FTIR)和拉曼光谱(Raman)等方法对其进行了表征, 结果表明, 石墨烯量子点组装体的平均高度为20 nm, 且富含大量的羟基和羧基. 电化学测试结果显示, 在共反应物K₂S₂O₈存在下, LSGQD-NAs在阴极产生很强的ECL(峰值约在685 nm); 并推测了其ECL反应机理, 发现LSGQD-NAs容易通过中心未氧化的石墨烯π-π作用于GC电极表面进行组装修饰. 本研究为基于石墨烯量子点ECL传感器的研究提供了新方法.     

基于血红蛋白/硒化镉量子点多层膜的H2O2生物传感器

合成了水溶性硒化镉(CdSe)量子点,利用组装技术和静电吸附作用,将带正电荷的血红蛋白(Hb)和带负电荷的CdSe量子点层层组装到壳聚糖(chit)修饰的玻碳电极(GCE)表面,构建基于{Hb/CdSe}n多层膜的无电子媒介体的电流型生物传感器({Hb/CdSe}3/chit/GCE).运用紫外-可见吸收光谱、电致化学发光、交流阻抗和循环伏安技术来表征修饰膜,并研究传感器的作用机理、性能及分析应用.结果表明:与量子点薄膜法及量子点/血红蛋白复合物法等固载血红蛋白的其他方法相比,层层组装法能显著提高血红蛋白的固定量,保持血红蛋白的生物活性,增强传感器的灵敏度和稳定性.传感器检测H2O2的线性范围为4.0×10-8～4.8×10-6 mol·L-1(r=0.999 1),检测限为2.0×10-8mol·L-l.多层膜的电致化学发光研究,表明修饰电极有望用于电致化学发光传感器的制备.     

Room‐Temperature Synthesis of Cu2−xE (E=S,Se) Nanotubes with Hierarchical Architecture as High‐Performance Counter Electrodes of Quantum‐Dot‐Sensitized Solar Cells

Copper chalcogenide nanostructures (e.g. one‐ dimensional nanotubes) have been the focus of interest because of their unique properties and great potential in various applications. Their current fabrications mainly rely on high‐temperature or complicated processes. Here, with the assistance of theoretical prediction, we prepared Cu_2?xE (E=S, Se) micro‐/nanotubes (NTs) with a hierarchical architecture by using copper nanowires (Cu NWs), stable sulfur and selenium powder as precursors at room temperature. The influence of reaction parameters (e.g. precursor ratio, ligands, ligand ratio, and reaction time) on the formation of nanotubes was comprehensively investigated. The resultant Cu_2?xE (E=S, Se) NTs were used as counter electrodes (CE) of quantum‐dot‐sensitized solar cells (QDSSCs) to achieve a conversion efficiency (η) of 5.02 and 6.25 %, respectively, much higher than that of QDSSCs made with Au CE (η=2.94 %).     

基于银纳米线复合透明电极的可弯折柔性聚合物太阳能电池

本文设计了一种可以通过刮涂方法制备的基于银纳米线(AgNWs)的柔性复合透明电极,并以此为基础实现了高性能柔性聚合物太阳能电池的制备。 基于银纳米线的柔性复合薄膜(APA)由银纳米线(AgNWs),聚乙烯醇缩丁醛(PVB)和铝掺杂氧化锌(AZO)纳米粒子在低温下通过多层刮涂的方法制备。 APA透明复合薄膜在550 nm处透光率达到90.90%,面电阻低至13.01 Ω/sq,在柔性基底上具有很高的粘附性。 在透明的APA/聚对苯二甲酸乙二醇酯(PET)基底上制备的柔性聚合物太阳能电池(PSCs),能量转换效率达到5.47%。 而且以5 mm为曲率半径,经过1000次循环弯曲实验,电池的能量转换效率仅下降了14%。     

TiO2微球的合成及其作为散射层在量子点敏化太阳能电池中的应用

以十六烷基三甲基溴化铵（CTAB）为模板剂,通过TiCl₄在乙醇水溶液中的直接水解,制备了介孔TiO₂微球. X射线衍射（XRD）结果表明所制备的微球晶型为金红石,扫描电镜（SEM）结果显示微球的直径大约为700 nm,由粒径约为16 nm的小颗粒堆积而成. 通过刮涂法制备了在TiO₂小颗粒层上涂覆有作为散射层的TiO₂微球和未涂覆微球的薄膜. 并通过化学浴沉积（CBD）的方法在膜上生长CdS/CdSe量子点,得到了量子点敏化太阳能电池（QDSCs）. 紫外吸收和漫反射结果表明,这种微球结构有利于量子点的沉积,具有较强的光散射作用,有效地增加了光线的收集,从而提高了电池的光电流,最终得到了4.5%的光电转换效率,比不加散射层的电池的效率高27.7%,也比利用传统散射层（由20 nm TiO₂ 小颗粒和400 nm TiO₂ 固体颗粒组成）的电池效率高10.2%. 我们把电池效率的提升归因于较强的光散射作用和较长的电子寿命.     

Effect of magnetic field on diamagnetic susceptibility of two interacting electrons in a quantum dot

We have estimated the energy levels of the low‐lying states as a function of magnetic field when two electrons are introduced in a quantum dot (QD). Oscillator strength of interacting electrons for different magnetic field strengths has been calculated. There is no appreciable change in oscillator strength for stronger confinements for all the magnetic field strengths. We present the shift of diamagnetic susceptibility of a hydrogenic donor impurity in GaAs/Ga_1?xAl_xAs QD systems for the ground and low lying excited states. The effect of magnetic field on diamagnetic susceptibilities is estimated by two different methods and it has been found that values obtained from both the methods resemble each other. The diamagnetic shift is in good agreement with the other investigators. © 2010 Wiley Periodicals, Inc. Int J Quantum Chem, 2011     

Quantum‐Dot‐Sensitized Solar Cells

Quantum‐dot‐sensitized solar cells (QDSCs) are a promising low‐cost alternative to existing photovoltaic technologies such as crystalline silicon and thin inorganic films. The absorption spectrum of quantum dots (QDs) can be tailored by controlling their size, and QDs can be produced by low‐cost methods. Nanostructures such as mesoporous films, nanorods, nanowires, nanotubes and nanosheets with high microscopic surface area, redox electrolytes and solid‐state hole conductors are borrowed from standard dye‐sensitized solar cells (DSCs) to fabricate electron conductor/QD monolayer/hole conductor junctions with high optical absorbance. Herein we focus on recent developments in the field of mono‐ and polydisperse QDSCs. Stability issues are adressed, coating methods are presented, performance is reviewed and special emphasis is given to the importance of energy‐level alignment to increase the light to electric power conversion efficiency.     

SnS‐Quantum Dot Solar Cells Using Novel TiC Counter Electrode and Organic Redox Couples

Low‐cost quantum‐dot sensitized solar cells (QDSSCs) were fabricated by using the earth‐abundant element SnS quantum dot, novel TiC counter electrodes, and the organic disulfide/thiolate (T₂/T^?) redox couple, and reached an efficiency of 1.03 %. QDSSCs based on I^?/I₃^?, T₂/T^?, and S^2?/S_x^2? redox couples were assembled to study the role of the redox couples in the regeneration of sensitizers. Charge‐extraction results reveal the reasons for the difference in J_SC in three QDSSCs based on I^?/I₃^?, T₂/T^?, and S^2?/S_x^2? redox couples. The catalytic selectivity of TiC and Pt towards T₂/T^? and I^?/I₃^? redox couples was investigated using Tafel polarization and electrochemical impedance analysis. These results indicated that Pt and TiC show a similar catalytic selectivity for I^?/I₃^?. However, TiC possesses better catalytic activity for T₂/T^? than for I^?/I₃^?. These results indicate the great potential of transition metal carbide materials and organic redox couples used in QDSSCs.     

Environmentally Benign and Efficient Ag2S‐ZnO Nanowires as Photoanodes for Solar Cells: Comparison with CdS‐ZnO Nanowires

In this work, we develop a low‐temperature, facile solution reaction route for the fabrication of quantum‐dot‐sensitized solar cells (QDSSCs) containing Ag₂S‐ZnO nanowires (NWs), simultaneously ensuring low manufacturing costs and environmental safety. For comparison, a CdS‐ZnO NW photoanode was also prepared using the layer‐by‐layer growth method. Ultraviolet photoelectron spectroscopy analysis revealed type‐II band alignments for the band structures of both photoanodes which facilitate electron transfer/collection. Compared to CdS‐ZnO QDSSCs, Ag₂S‐ZnO QDSSCs exhibit a considerably higher short‐circuit current density (J_sc) and a strongly enhanced light‐harvesting efficiency, but lower open‐circuit voltages (V_oc), resulting in almost the same power‐conversion efficiency of 1.2 %. Through this work, we demonstrate Ag₂S as an efficient quantum‐dot‐sensitizing material that has the potential to replace Cd‐based sensitizers for eco‐friendly applications.     

单晶二氧化钛纳米棒阵列的修饰及其在量子点敏化太阳电池中的应用(英文)

使用TiCl4溶液对单晶TiO2纳米棒阵列(TNRs)进行修饰,通过在TiO2纳米棒表面合成TiO2纳米颗粒来提高TNRs的表面积,提高TNRs对量子点的吸附能力,并在此基础上研究了TiCl4修饰时间对基于单晶TNRs的CdS/CdSe量子点敏化太阳电池光伏性能的影响,同时结合强度调制光电流谱(IMPS)研究了TiO2纳米棒阵列的电子传输性能.结果表明:TiCl4修饰可以大幅提高基于单晶TNRs的CdS/CdSe量子点敏化太阳电池的光伏性能,在TiCl4修饰时间为60 h时,其短路电流密度和光电转换效率分别由修饰前的(2.93±0.07)mA·cm-2和0.36%±0.02%提高至(8.19±0.12)mA·cm-2和1.17%±0.07%.同时,IMPS测试表明电子在单晶TiO2纳米棒阵列中的传输速率高于在TiO2纳米颗粒薄膜中的传输速率,证明了单晶TiO2纳米棒阵列在电子传输方面的优越性.