CuCl/SiO2-TiO2 催化剂的结构及其催化甲醇氧化羰基化反应性能

 在微波辐射条件下, 将 CuCl 快速分散到载体表面制得 CuCl/SiO2-TiO2 催化剂, 利用 X 射线衍射、透射电镜、N2 吸附-脱附、热重、H2 程序升温还原和 CO 程序升温脱附对催化剂进行了表征. 结果表明, 微波辐射制备的催化剂中 CuCl 和载体发生了强相互作用, 比传统加热制备的催化剂中形成更多的易还原铜物种, 吸附 CO 的能力更强. 在甲醇液相氧化羰基化反应中, 微波辐射制备的催化剂上甲醇转化率为 11.7%, 碳酸二甲酯选择性达 96.5%, 高于相同条件下传统加热制备催化剂的活性.     

MoP/SiO_2-TiO_2-ZrO_2加氢脱硫催化剂的研制

采用共沉淀法制备了SiO2-TiO2-ZrO2复合载体,并用共浸渍法制备了负载型MoP/SiO2-TiO2-ZrO2催化剂,通过H2原位还原技术对催化剂进行还原处理,在小型连续固定床反应器上进行催化剂的加氢脱硫活性评价。结果表明,SiO2-TiO2-ZrO2复合载体为介孔材料,MoP/SiO2-TiO2-ZrO2比一元及二元载体催化剂的加氢脱硫活性提高了12-31%;Si/Ti/Zr摩尔比以及MoP的负载量对催化剂的活性有很大影响,当n(Si)/n(Ti)/n(Zr)=0.163/0.809/0.028、MoP的负载量为20%时,催化剂的加氢脱硫效果最好:在380℃、压力4.0 Mpa、空速6 h(1、氢油比500条件下,二苯并噻吩的转化率达到了99.1%。     

CeO2-TiO2混合氧化物及Pd/CeO2-TiO2催化剂的氧化还原性能

 以溶胶-凝胶-超临界流体干燥法制备了CeO2-TiO2混合氧化物(n(Ce)/n(Ti)=0.05～0.40),以其为载体,通过等体积浸渍法制备了Pd/CeO2-TiO2催化剂. XRD分析结果表明,在低Ce/Ti比的CeO2-TiO2混合氧化物中,CeO2高度分散于TiO2上; Ce/Ti比高于0.10时,大晶粒锐钛矿相TiO2和TiO2-CeO2固溶体或其前驱体无定形相共存. 采用H2-TPR对所合成材料的氧化还原性能进行了研究. H2-TPR谱中500 ℃附近的耗氢峰对应于CeO2-TiO2中CeO2的还原,还原过程中不存在表面晶格氧与体相晶格氧的差别. 由于TiO2与CeO2的协同作用,混合氧化物中形成了丰富的结构缺陷,提高了CeO2的氧化还原性能,其中Ce/Ti比为0.20时TiO2与CeO2的协同作用最显著. 负载上Pd后,载体中CeO2的还原温度(＜150 ℃)大大降低,同时随着Ce/Ti比的增大,PdO与载体间的相互作用增强,导致PdO难于还原,相应的H2-TPR还原峰向高温方向移动.     

Ti(Ⅳ)掺杂Bi_2O_3电子结构和可见光催化活性的原理

密度泛函理论(DFT)计算对掺杂体系新型环境光催化剂设计开发具有指导意义.基于DFT框架下的第一性原理平面波超软赝势方法(USPP),对α、β、γ、δ-Bi2O3晶体几何结构分别进行了优化计算,从理论上得到了Bi2O3的总体态密度(TDOS)和Bi、O原子的分波态密度(PDOS).在此基础上对Bi2O3超晶胞进行Ti(IV)的掺杂计算,讨论了Ti(IV)掺杂对各种Bi2O3的电子结构和光吸收特性的影响.结果表明Ti(IV)掺杂Bi2O3晶体后,Ti(IV)的3d轨道进入禁带并与O2p、Bi6p轨道作用,使禁带宽度(Eg)变小,Bi2O3的吸收边红移,从而有助于Bi2O3光催化活性的改善.通过水热合成法制备的Ti(IV)掺杂Bi2O3样品的紫外-可见光漫反射光谱验证了计算的结果.在光催化降解有机染料结晶紫的实验中,光催化剂活性的改善进一步得到证实.     

CuCl／SiO2-Al2O3催化剂的表面结构及甲醇氧化羰基化催化性能

通过掺杂Al对无定形层析硅胶进行表面改性,采用固体离子交换法制备了CuCl/SiO2-Al2O3催化剂,并考察了它在甲醇液相氧化羰基化合成碳酸二甲酯反应中的催化性能.结果表明,掺杂Al制备的SiO2-Al2O3载体仍保持了硅胶的无定形结构,比表面积降为200m2/g,但表面酸性明显增强,具有B酸中心.CuCl不仅分散于SiO2-Al2O3载体表面,而且与载体表面的B酸发生离子交换作用形成了表面Cu 物种,使催化剂比表面积降为148m2/g,且两种Cu 物种共同构成了催化活性中心.当CuCl/SiO2-Al2O3催化剂的Si/Al比为5,在500℃焙烧时,催化剂上甲醇氧化羰基化反应的碳酸二甲酯的选择性和时空收率分别达到74%和1.27g/(g.h).     

SnO_2改性TiO_2对V_2O_5-WO_3/TiO_2催化剂结构和SCR性能影响

采用共沉淀法将SnO_2组分掺入到V_2O_5-WO_3/TiO_2催化剂载体TiO_2中,并通过多种物理化学手段,考察了不同SnO_2掺入量时对催化剂结构,表面分散物种和SCR性能影响.结果表明,SnO_2掺入到TiO_2中,元素Sn与Ti以Sn—O—Ti键形式相互作用,促进锐钛矿型TiO_2向金红石型TiO_2转变.在特定条件下,VO_x与WO_x物种和SnTi氧化物之间以V—O—Ti(Sn)和W—O—Ti(Sn)键形式相互作用,提高了VO_x物种可还原能力、促进了具有更多B酸酸量四面体WOx物种和V~(5+)物种生成.VW/SnTi催化剂表面VO_x物种与WO_x物种之间的相互作用更强.因此,VW/SnTi催化剂具有更好的SCR活性.     

CeO2-TiO2复合氧化物的制备、表征及其对CO氧化的催化性能

采用溶胶-凝胶法制备了一系列不同n(Ce)/n(Ti)的CeO2-TiO2复合氧化物,对复合氧化物的物相结构、形貌特征、比表面积和氧化还原性质进行了表征,并考察了复合氧化物对CO氧化反应的催化性能.结果表明,n(Ce)/n(Ti)>0.10时,复合氧化物为无定形结构;n(Ce)/n(Ti)=0.10~0.30时,复合氧化物失去CeO2和TiO2各自的特征,形成CeO2-TiO2固溶体,具有较大的比表面积.CeO2-TiO2复合氧化物本身对CO氧化反应的催化活性不如TiO2或CeO2的高,但Pd/CeO2-TiO2比Pd/TiO2或Pd/CeO2具有更高的催化活性.     

纳米TiO2-SiO2复合氧化物的制备与性质

采用溶胶-凝胶结合CO2超临界干燥方法制备了比表面积大、热稳定性好的纳米TiO2-SiO2复合氧化物.考察了原料组成和焙烧温度对复合氧化物比表面积、热稳定性和酸性的影响,通过加氢脱硫反应考察了该复合氧化物作为加氢精制催化剂载体的可行性.结果表明,采用该方法制备的复合氧化物为纳米颗粒,在n(Ti)/n(Si)=1时,其比表面积和孔容最大;与纯TiO2相比,引入SiO2明显提高了复合氧化物的热稳定性和晶型稳定性;以此复合氧化物为载体的加氢精制催化剂具有很好的低温脱硫活性,TiO2-SiO2复合氧化物载体的酸性特征影响了催化剂的加氢脱硫活性.     

碱土金属氧化物对丙三醇和苯胺气相合成_3-甲基吲哚的Cu/SiO_2-Al_2O_3催化剂的作用(英文)

研究了碱土金属氧化物的添加对丙三醇和苯胺气相合成3-甲基吲哚的Cu/SiO2-Al2O3催化剂性能的影响,采用X射线衍射、透射电镜、H2程序升温还原、NH3程序升温脱附以及热重-差热等技术对催化剂进行了表征.结果表明,MgO能加强活性组分和载体之间的相互作用,从而促进铜粒子在载体上的分散.另外,MgO能增加弱酸中心数,并且抑制积炭的形成,因而Cu-MgO/SiO2-Al2O3催化剂性能大大提高;而CaO,SrO或BaO的加入不利于Cu/SiO2-Al2O3催化剂上3-甲基吲哚的生成.这是由于铜粒子在载体上的分散度变差,而且在Cu-SrO/SiO2-Al2O3及Cu-BaO/SiO2-Al2O3催化剂上弱酸中心数较少.碱土金属氧化物的加入不能改变催化剂上积炭的结构.     

V2O5-TiO2催化剂光催化降解2,4-二氯苯酚：催化剂载体和表面活性剂的影响

采用固态分散法成功制备了表面活性剂修饰的不同V2O5含量的二元氧化物催化剂,运用X射线衍射、漫反射光谱、红外光谱、扫描电镜和N2吸附-脱附法对该纳米复合物进行了表征,并在紫外光照射下考察了其光催化降解2,4-二氯苯酚的性能.结果表明,50 wt%, V2O5-TiO2(记为50V2O5-TiO2)表现出比单纯V2O5, TiO2和P25更高的光催化活性, V2O5和TiO2之间的相互作用会影响二元氧化物催化剂的光催化效率. CTAB和HTAB的修饰显著增加了50V2O5-TiO2样品的催化效率,其中(50V2O5-TiO2)-CTAB催化剂在反应30 min后表现出最高的2,4-二氯苯酚降解率(100%)和反应速率(2.22 mg/(L·min)).表面活性剂的加入能修饰二元氧化物中V2O5和TiO2的光学和电子性质,从而显著提高其光催化活性.     

圆盘状α-Co(OH)2的控制合成及其电化学性能

采用AAO模板及后处理方法合成了圆盘状α-Co(OH)₂并研究了其电化学电容性能. 在该合成方法中, 先采用阳极氧化铝模板结合交流电沉积的方法获得钴纳米线, 而后将其在碱液中通过溶解氧氧化生成终端产物. 用红外光谱(FT-IR), X射线衍射(XRD)和场发射扫描电子显微镜(FE-SEM)表征了产物的结构和形貌; 用循环伏安、恒电流充放电测试方法对其电化学性能进行了测试. 此外, 对圆盘状Co(OH)₂的形成机理进行了初步探讨. 结果表明, 用此方法合成的Co(OH)₂具有圆盘状形貌, 属α相态, 且表现出较好的电容特性.     

氨基聚乙二醇-1,2-二硬脂酰甘油磷酰乙醇胺的合成

以1,2-二硬脂酸甘油酯为原料,与三氯氧磷及乙醇胺反应合成1,2-二硬脂酰甘油磷酰乙醇胺(DSPE);再以聚乙二醇2000 (PEG2000)为原料,通过磺酰化、叠氮化反应合成叠氮基聚乙二醇2000(N_3-PEG2000); DSPE与N_3-PEG2000在N,N-羰基二咪唑(CDI)作用下生成叠氮基聚乙二醇2000-1,2-二硬脂酰甘油磷酰乙醇胺(N_3-PEG2000-DSPE);最后通过催化氢化制备氨基聚乙二醇2000-1,2-二硬脂酰甘油磷酰乙醇胺(NH_2-PEG2000-DSPE),其结构经过IR、MS及~1H NMR等确证。     

Titania-Doped Silica Fibers Prepared by Electrospinning and Sol-Gel Process

Titania-doped silica fibers were prepared by electrospinning of the sol of silica containing titania. The electrospun fibers had ribbon type morphology. The fibers had significant quantities of hydroxyl groups of Si—OH and Ti—OH. The fibers did not have crystalline structure. Diameters of the fibers were reduced by solvent evaporation and calcination. The hydroxyl groups on the fibers disappeared by calcination. The hydroxyl groups, M—OH (MSi, Ti) were changed to M—O—M by intermolecular and intramolecular condensation reactions.     

29Si and 17O NMR investigations on Si−O−Ti bonds in solutions of diphenylsilanediol and titanium-tetra-isopropoxide

The structural units in diphenylsilanediol/titanium-isopropoxide solutions with molar ratio Si:Ti between 1:0.1 and 1:5 were examined by means of ²⁹Si and ¹⁷O NMR. The main component in solutions with molar ratio Si/Ti=1:0.1 is the chain-like octaphenyltetrasiloxanediol. With increasing Ti-isopropoxide content (1:0.25–1:05) Si–O–Ti units of the spirocyclic titanosiloxane Ti[O₅Si₄(C₆H₅)₈]₂ prevail in the solutions accompanied by the chain-like tetrasiloxanediol. The ²⁹Si NMR spectra of 1:1 solutions indicate a lot of different Si containing building units with chemical shifts mainly between-40 and-46 ppm. The signals with a chemical shift between-40 and-46 ppm are probably caused by Si atoms which are connected via oxygen bridges directly (Si–O–Ti) or indirectly (Si–O–Si–O–Ti) with titanium. Contrary to the 1:1 solutions only one or two different species with Si–O–Ti units are present in high Ti-alkoxide containing solutions (1:5). ²⁹Si and ¹⁷O NMR results reveal a quick hydrolysis of the Ti–O–Si bonds to titanium-oxo-hydroxo-polymers and phenylsiloxanediols or their isopropyl esters after the addition of water to the solutions. This separation into species only containing either Ti–O–Ti or Si–O–Si bonds can entail a decreased homogeneity of the reaction products on a molecular level.     

Structural Features of Grafted Phosphates in Mesopores of Si-MCM-41 and Ti,Si-MCM-41 Molecular Sieves

We have used ³¹P NMR (MAS) and IR spectroscopy and also chemical analysis to show that when Si- and Ti,Si-MCM-41 mesoporous molecular sieves are treated with phosphorus oxychloride, surface-anchored silicophosphate and titanophosphate compounds are formed of the type (Si—O) _x —{PO(OH)_3–x } and (Ti—O) _x —{PO(OH)_3–x } (x = 1, 2), and also compounds with the structure of titanium hydrophosphate and pyrophosphate.     

An XPS study of microporous and mesoporous titanosilicates

In this contribution we report on an XPS study of microporous and mesoporous titanosilicates, in particular microporous titanium silicalite TS‐1, ordered mesoporous Ti‐MCM‐41 and [Ti]‐MCM‐41 and amorphous mesoporous silica–titania (MST) catalysts. Our aim was to obtain both photoemission and x‐ray‐excited Auger data for Ti species on these catalysts and use them in a Ti Wagner plot to rationalize the dependence of the local electronic structure on the atomic environment. Isolated Ti(IV) species coordinated to four and six oxygen anions and segregated TiO₂ clusters were detected on all catalysts by a curve‐fitting procedure of Ti 2p, O 1s and related peaks. The presence of the Si 2p peak excited by an O Kα ghost makes the detection of Ti LMM Auger transitions in mesoporous samples impossible due to the low Ti loadings and its homogeneous distribution in the silica matrix. Small TiO₂ clusters are eventually segregated within the mesopores of the catalysts and not at their external surface. On TS‐1 microporous catalysts with similar Ti loadings to the mesoporous catalysts we were able to detect Ti LMM Auger transitions, and by the Ti Wagner plot we clearly identify the presence of octahedrally coordinated Ti(IV) species. Thus, it is suggested that on TS‐1 the in‐framework (? O)₄Ti species are easily changed to (? O)₄(H₂O)₂Ti species by insertion of water molecules from the atmosphere. Small TiO₂ clusters (diameter <5 nm), eventually present on samples with Ti loading >2 wt.%, are segregated at their external surface and present spectroscopic features similar to (? O)₄(H₂O)₂Ti species. Copyright © 2004 John Wiley & Sons, Ltd.     

无溶剂条件下5,6-二取代-2,3-吡啶二酮的合成

在无溶剂条件下, 由3-羟基-2(1H)-吡啶酮与取代苯胺在NaIO₃作用下合成了一系列5,6-二取代-2,3-吡啶二酮, 产物结构由元素分析, ¹H NMR, MS, IR得到确认. 该方法具有反应条件温和、操作简单和产率高等优点.     

样品价态对激光气化产生Cu/Cl团簇的组成和稳定性的影响

研究团控的形成条件、形成机理是目前团簇科学中的一个热点领域［‘］．产生气相团簇的方法主要有Knudsen高温炉扩散法、粒子溅射法、激光气化／分子束法、直接激光气化法·因为不需要另加缓冲气体，直接激光气化法【刀具有对体系真空要求较低，装置简单，容易和飞行时间质谱结     

On the Existence and Hydrolytic Stability of Titanosiloxane Bonds in the System: Glycidoxypropyltrimethoxysilane-Water-Titaniumtetraethoxide

Heterometal materials based on glycidoxypropyltrialkoxysilane and titaniumalkoxide are used for optical applications and require a high homogeneity on the molecular level. The presence of heterometal titanosiloxanes, their distribution and hydrolytic stability should influence the homogeneity of these materials. 29Si and 17O NMR spectroscopy has been used to investigate sols with molar ratios Si : Ti = 1 and H2O : OR (H) = 0.5 – 2.0 and their gels after heat treatment at 130°C. The presence of Si—O—Ti bonds in sols with a low water content (H < 0.2) and in the corresponding gels was identified by the high-field shift of the 29Si NMR signals of T1 and T2 units of up to 2–3 ppm compared to corresponding signals of homo-condensed Si—O—Si bonds. The existence of Si—O—Ti bonds in the sols is supported by 17O NMR spectra which show a characteristic signal around 340 ppm. A cleavage of the Si—O—Ti bonds occurs with increasing water/OR ratio in the sols. The cleavage of the heterometal bonds and the building up of homo-condensed species leads to a separation into areas with predominantly Ti—O—Ti and Si—O—Si bonds resulting in a decreased molecular homogeneity of the materials.     

氧官能化的膦配体在钯催化的Suzuki-Miyaura反应中的应用

合成了带甲氧基和羟基官能团的二茂铁膦配体, 评价了它们在钯催化的Suzuki-Miyaura偶联反应中的性能, 发现带甲氧基的膦配体对钯催化的Suzuki-Miyaura偶联反应有更好的性能, 可催化富电子溴代芳烃和缺电子氯代芳烃与苯硼酸反应高产率地生成相应的联芳烃产物.