碳纳米管负载铂催化剂的制备、结构及电化学加氢特性

采用浸渍沉淀法制备Pt/CNTs和Pt/C催化剂,并对其结构及电催化性能进行比较,表征.实验表明,以碳纳米管作催化剂载体可使催化剂的负载量,载体上铂的分散度以及其活性中心大大提高.与Pt/C(JohnsonMatthey)催化剂相比,Pt/CNTs的电化学性能表现出更大的活性.碳纳米管作为阴极材料在质子交换膜燃料电池加氢反应器合成化学品中的作用十分明显.     

激光溅射法制备Pt/CNTs催化剂用于邻氯硝基苯的液相加氢反应

采用激光溅射法制备了碳纳米管负载铂(Pt/CNTs)催化剂, 并利用透射电子显微镜(TEM)、X射线能量散射谱(EDS)、X射线衍射(XRD)、X射线光电子能谱(XPS)等表征手段研究了Pt粒子在碳纳米管表面存在的状态、组成、结构等性质. 讨论了Pt/CNTs催化剂的不同制备条件对催化剂结构的影响, 并考察了催化剂对邻氯硝基苯液相加氢合成邻氯苯胺反应的加氢性能. 研究结果表明, 在激光电压为250 V, 绝对压力为300 Pa, 载体温度为25 ℃条件下制备的Pt/CNTs催化剂, 在不加脱卤抑制剂, 反应温度为60 ℃和氢气压力为1.0 MPa的条件下, 邻氯硝基苯转化率可以达到99.7%以上, 邻氯苯胺选择性可达到98.2%以上, 表现出较高的加氢性能和抑制脱卤性能.     

纳米碳纤维载铂作为质子交换膜燃料电池阳极催化剂

采用化学还原法合成了微结构不同的纳米碳纤维(板式、鱼骨式、管式)载铂催化剂(分别记为Pt/p-CNF、Pt/f-CNF、Pt/t-CNF). 通过高分辨透射电镜(HRTEM)和X射线衍射(XRD)等分析技术对催化剂的微观结构进行了表征, 并利用循环伏安(CV)法分析了催化剂的电化学比表面积(ESA). 在此基础上, 制备了膜电极(MEA), 通过单电池测试了催化剂的电催化性能. 结果表明: 铂纳米粒子在不同的纳米碳载体上表现出不同的粒径, 在板式、鱼骨式和管式纳米碳纤维上的铂纳米粒子平均粒径分别为2.4、2.7和2.8 nm. 板式纳米碳纤维载铂催化剂作单电池阳极时表现出良好的电催化性能, 其对应的最高功率密度可达0.569 W·cm^-2, 高于鱼骨式纳米碳纤维载铂催化剂和管式纳米碳纤维载铂催化剂对应的最高功率密度(分别为0.550和0.496 W·cm^-2). 同时, 也制备了碳黑(Pt/XC-72)载铂催化剂. 相比于Pt/XC-72, 纳米碳纤维载体上的铂纳米颗粒有较小的粒径、较好的分散和较高的催化活性, 说明纳米碳纤维是质子交换膜燃料电池(PEMFCs)催化剂的良好载体.     

碳纳米管结构对碳纳米管载Pt催化剂电催化性能的影响

在制备单、双壁及不同管径的多壁碳纳米管(CNTs)的基础上, 用液相还原法把Pt沉积到单、双壁和管径不同的多壁CNTs上. 发现制得的CNTs载Pt(Pt/CNTs)催化剂对甲醇氧化的电催化活性随CNTs管径减小而增加. 这归结于管径小的CNTs的比表面积较大, 含氧基团多, 有利于提高Pt粒子分散度, 加上管径小的单壁CNTs具有更高的导电性, 这些因素都有利于提高Pt/CNTs催化剂对甲醇氧化的电催化活性.     

碳纳米管电极上原位沉积Pt纳米颗粒

 本文利用原位离子交换法制备了碳纳米管(CNTs)载铂(Pt/CNTs)电极. X射线光电子能谱分析表明, Pt通过离子交换载于电化学功能化的CNTs表面. 扫描电镜照片显示, Pt高度分散于CNTs表面. X射线衍射分析表明, Pt的粒径约为4.0 nm. 离子交换法所制Pt/CNTs电极的电化学表面积和Pt的利用率均大于传统Pt/CNTs电极(Pt粒径约为2.5 nm), 其对氧还原的催化活性高于传统电极. 这归因于离子交换法所制电极的特殊结构,即Pt普遍载于电化学活性位上.     

层级多孔碳载铂催化剂的制备及可达性

层级多孔碳作为氧还原铂基催化剂载体的选择之一, 简单的旋转圆盘电极(RDE)验证此类催化剂具有较高的氧还原活性, 但几乎都缺少膜电极(MEA)性能验证, 实用性无法保证. 本文设计制备了基于聚苯胺的层级多孔碳（NHPC）载铂催化剂（Pt/NHPC850）, 研究了其氧还原活性、 MEA质子传输和氧传输特性. RDE测试研究表明, Pt/NHPC850催化剂在低I/C（离聚物与碳载体质量比）时的面积活性低于实心碳载铂催化剂（Pt/XC-72）, 但当I/C增大到与膜电极中一致时, 由于Nafion树脂对Pt催化剂的毒化作用增强, 其面积活性反而优于 Pt/XC-72. Pt/NHPC850催化剂的高Pt分散性及其优异的抗Nafion毒化性能, 使其在I/C为0.8时的质量活性为Pt/XC-72催化剂的1.34倍. MEA质子传输研究表明, 即使在高加湿条件下, Pt/NHPC850质子电阻率仍高达72.6 mΩ·cm², 为Pt/XC-72的3倍. Pt/NHPC850制备的膜电极极化曲线在500 mA/cm²电流密度下性能迅速下降, Pt/NHPC850的氧增益电压达到144.4 mV, 比Pt/XC-72高56.7 mV. 表明Pt/NHPC850膜电极的质子传输和氧传输性能较差. 对比Pt/NHPC850催化剂的RDE和MEA的测试结果, 说明以层级多孔碳为载体的铂碳催化剂虽然耐Nafion毒化能力提高, 但是质子和氧气的氧传输性较差, 此类层级多孔碳还需进一步优化其结构, 才有可能满足低铂质子交换膜燃料电池（PEMFC）的应用需求.     

甲醇在Pt/C和Pt/WO_3/C电极上的电氧化

用液相还原法制备碳载Pt(Pt/C)和碳载Pt/WO3(Pt/WO3/C)催化剂.实验表明该催化剂中加入一定量的WO3后,其对甲醇的催化氧化活性和稳定性都有一定提高,并以Pt、W原子比为1∶1的催化剂性能最好.这是由于Pt催化剂中加入了WO3后,其电化学活性比表面积增大,并且降低了对CO吸附强度.     

快速功能化碳纳米管载 Pt 催化剂的醇氧化性能(英文)

采用HF刻蚀及交替微波加H2O2相结合的方法进行快速功能化碳纳米管(CNTs),应用红外光谱、拉曼光谱和透射电镜等方法详细考察了CNTs及其载Pt催化剂的物化性质,并采用循环伏安法、线性电流扫描法和计时电流法考察了所得催化剂的电化学性能.结果表明,CNTs经过HF刻蚀和交替微波H2O2双重处理后更适合用作催化剂载体,以10s-on/20s-off加热5次所得CNTs载Pt催化剂显示出最佳的催化性能.这可归因于处理后的CNTs表面含有丰富的微孔及含氧官能团,能有效增强Pt颗粒及CNTs间的相互作用.     

Pt/CeO2/CNTs催化剂对甲醇电催化氧化的研究

通过微波乙二醇法制备了Pt/CeO2/CNTs催化剂用于碱性体系中的甲醇电催化氧化,考察了不同的CeO2含量对其电催化活性的影响.X射线衍射(XRD)和透射电镜(TEM)结果表明,Pt/CeO2/CNTs催化剂中Pt颗粒较小,在载体上分散性较好.循环伏安曲线和计时电流测试结果表明,Pt/CeO2/CNTs催化剂表现出良...     

聚乙烯亚胺改性石墨烯载Pt催化剂的制备及其对甲醇的电催化氧化

以聚乙烯亚胺(PEI)改性的石墨烯(PEI-GNs)为载体,利用原位电化学还原法制备了功能化石墨烯载铂催化剂(Pt/PEI-GNs)。运用X射线光电子能谱、X射线粉末衍射、扫描电镜等对催化剂的组成、结构、形态进行表征,结果表明:实验成功制备了Pt/PEI-GNs催化剂,且PEI-GNs改善了Pt粒子的分散性和形貌。运用电化学方法考察了PEI-GNs对Pt纳米粒子电催化性能的影响,结果表明,相对于Pt催化剂,Pt/PEI-GNs催化剂表现出更高的催化活性和稳定性,这主要是由于Pt粒子在PEI-GNs载体上形成均匀分散的绣球状粒子及PEI-GNs良好的电子传递能力。     

Ethanol electro-oxidation on catalysts with TiO2 coated carbon nanotubes as support

Pt–TiO₂/CNTs electrocatalysts for direct ethanol fuel cells (DEFCs) were prepared by sol–gel and ethylene glycol reduction method. XRD and TEM showed that the size of the Pt particles on TiO₂/CNTs is 3.5–4 nm and with narrow particle size distribution. HRTEM revealed that a thin layer of uniform amorphous TiO₂ on CNTs was formed and the faces of the Pt crystal on Pt–TiO₂/CNTs catalysts were quite “rough” and “rounded” and some grain bounders and/or twins also appeared. The electrochemical studies using cyclic voltammetry (CV), chronoamperometry and CO stripping voltammetry indicate that Pt–TiO₂/CNTs catalysts have higher electro-catalytic activity and CO-tolerance for ethanol oxidation than Pt/C (20 wt% Pt, E-TEK) and Pt/CNTs catalyst in acid. The Pt/TiO₂ molar ratio was also optimized and proved that 1:1 was the best Pt/TiO₂ molar ratio.     

Pt/MO2/CNTs（M=Sn,Ti,Ce）催化剂上乙醇电氧化研究

应用循环伏安法研究了几种催化剂Pt/MO2/CNTs(M=Sn,Ti,Ce)和Pt/CNTs对乙醇在H2SO4溶液中的电催化氧化过程.结果表明,金属氧化物的加入有利于乙醇的电氧化.其中,Pt/CeO2/CNTs对乙醇电氧化中间态产物具有显著的氧化性能.综合初始氧化电位、峰电流和总氧化峰面积等参数,可以得出Pt/SnO2/CNTs催化剂性能最佳.     

管径对碳纳米管负载铂催化剂氧还原的影响

A series of nanocatalysts consisting of acid treated carbon nanotubes (CNTs) with different diameters (8-15, 20-30, 30-50, >50 nm) supporting platinum (Pt) nanoparticles (Pt/CNTs) were synthesized via a microwave-assisted ethylene glycol method. The as-synthesized catalysts were characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and transmission electron microscopy (TEM). Their catalytic performances in the oxygen reduction reaction (ORR) were evaluated by cyclic voltammetry (CV) and linear sweep voltammetry (LSV). The experimental results showed that the diameter of the CNTs influences the particle size, loading, and dispersion of Pt NPs. Furthermore, the Pt/CNTs having different CNT diameters displayed different catalytic activities in the ORR. The catalyst Pt/CNT₈, which was prepared by using CNTs with diameters ranging between 8-15 nm as the support, exhibited the highest Pt loading, catalytic activity, and stability in the ORR. The mass activity of Pt/CNT₈ was determined to be 0.188 A·mg^-1 at 0.9 V, which is folds higher than that of the commercially available JM Pt/C catalyst. After testing the stability for 5000 potential cycles, the negative shift (~7 mV) of the half-wave potential for Pt/CNT₈ was found to be significantly lesser than that for the JM Pt/C catalyst (~32 mV), indicating superior catalytic stability.     

碳纳米管纯化对Pt/CNTs催化甲醇电化学氧化活性的影响

探索了一种适用于Pt/CNTs催化剂的纯化方法.利用比表面积测定、X射线衍射(XRD)、透射电子显微镜(TEM)和电化学等手段进行了表征.研究结果表明,经该方法纯化的CNTs作为载体制备的阳极催化剂表现出明显优于相应的混酸氧化法纯化的CNTs为载体的催化剂催化性能.     

Pt/MO2/CNTs催化剂上乙醇电氧化研究

应用循环伏安法研究了几种催化剂Pt/MO2/CNTs（M = Sn, Ti, Ce）和Pt/CNTs对乙醇在H2SO4溶液中的电催化氧化过程。结果表明,金属氧化物的加入有利于乙醇的电氧化,其中,Pt/CeO2/CNTs对乙醇电氧化中间态产物具有显著的氧化性能。综合初始氧化电位、峰电流、总氧化峰面积等参数可以得出Pt/SnO2/CNTs催化剂性能最佳。     

Platinum catalysts prepared with functional carbon nanotube defects and its improved catalytic performance for methanol oxidation

Carbon nanotube (CNT) supported Pt nanoparticle catalysts have been prepared by spontaneous reduction of PtCl6(2-) ion as a result of direct redox reactions between PtCl6(2-) and oxygen-containing functional groups at defect sites of CNTs, which were introduced by chemical and electrochemical oxidation treatment of CNTs. The electrocatalytic properties of as-prepared Pt-CNT catalysts for methanol oxidation were investigated by chronopotentiometry and cyclic voltammetry. Compared with Pt catalysts prepared by hydrogen reduction and electrochemical deposition methods, Pt catalysts synthesized by functional CNT defects show excellent antipoisoning ability and long-term cycle stability.     

Nitrogen-doped carbon nanotubes as a cathode catalyst for the oxygen reduction reaction in alkaline medium

A new approach to synthesize nitrogen-doped carbon nanotubes (NCNTs) as catalysts for oxygen reduction by treating oxidized CNTs with ammonia is presented. The surface properties and oxygen reduction activities were characterized by cyclic voltammetry, rotating disk electrode and X-ray photoelectron spectroscopy. NCNTs treated at 800 °C show improved electrocatalytic activity for oxygen reduction as compared with commercially available Pt/C catalysts.