聚醚链段长度对氨基聚醚-环氧树脂力学性能的影响

以柔性端氨基聚醚(BATPE)和双酚A环氧树脂(DGEBA)为原料, 制备了无微相分离结构的无定型AB交联热固性树脂. 测试了3种不同聚乙二醇(PEG)链段长度(M_PE)的BATPE-DGEBA环氧树脂固化产物的应力-应变曲线、动态力学温度谱和冲击断面形貌. 结果表明, 在环氧树脂交联网络中引入两端与DGEBA化学连接的PEG链段能避免微相分离结构的生成, 有利于提高DGEBA链段的应变松弛速率. 增加M_PE, 一方面能降低环氧树脂固化产物的玻璃化转变温度和室温下的刚度和拉伸强度, 增加韧性(包括冲击强度和拉伸韧性)、断裂应变和模量损耗因子; 另一方面也能提高固化产物在低温下的储存模量. 优化M_PE可制备出在中低温下同时具有优异的拉伸强度、模量、断裂应变和冲击性能的BATPE-DGEBA环氧树脂.     

羧甲基壳聚糖/有机累托石纳米复合材料及其药物缓释性能研究

利用简单的溶液插层法制备了羧甲基壳聚糖/有机累托石纳米复合材料,其中累托石(REC)用十六烷基三甲基溴化铵进行改性.用X-射线衍射(XRD)、红外光谱(FTIR)和扫描电镜(SEM)表征了该纳米复合材料的微观结构和形态,实验表明羧甲基壳聚糖插层进入了累托石层间,增大了累托石的层间距,并且累托石均匀地分布在羧甲基壳聚糖基体中.以牛血清蛋白(BSA)为药物模型,研究了纳米复合材料与海藻酸钠形成的微球的药物缓释性能.结果显示,该微球对药物的包封率及缓释性能与纯羧甲基壳聚糖微球相比都有较大改善,包封率从56%提高到86%,药物缓释时间从24 h上升到72 h.并且纳米复合材料/海藻酸钠微球的释药具有pH响应性,在pH为1.2的条件下释药慢,而在pH为7.4时释药快,可用于小肠或结肠定位缓释系统.因此,羧甲基壳聚糖/有机累托石纳米复合材料很有潜力作为药物载体.     

层状硅酸盐累托石/环氧树脂纳米复合材料的结构和性能研究

用有机改性的层状累托石与环氧树脂复合制备出纳米复合材料 .通过改变累托石含量发现在很低含量 (0 5W % )时纳米复合材料具有最佳力学和热学性能 ,冲击强度增加 12 0 % ,断裂伸长率增加 330 %玻璃化转变温度提高 2 8℃ .用X衍射、透射电镜和红外吸收光谱研究了材料的微观结构 ,结果表明层状累托石和环氧树脂发生了化学反应 ,观测到了层状累托石完全剥离和插层两种结构形态 ,且累托石含量较低时容易形成剥离型 .具有大的比表面积、高的反应活性的累托石片层分散于环氧基体中形成剥离型为主的结构有利于改善复合材料的力学性能并增加其热稳定性 .     

4,4'-二氨基二苯醚二苯酮固化环氧树脂/粘土纳米复合材料的研究

采用离子交换法, 用十六烷基三甲基溴化铵处理钙基蒙脱土(MMT), 使蒙脱土的层间距由1.49 nm扩大到2.21 nm, 制备了环氧树脂/ BADK/MMT纳米复合材料, 并用XRD等手段研究了有机蒙脱土在环氧树脂中的插层及剥离行为. 研究结果表明, 蒙脱土含量及环氧树脂与有机土的混合温度和时间均对固化后复合材料的剥离产生影响, 只有在特定条件下才能得到剥离型纳米复合材料.     

新环氧树脂纳米复合材料的合成和结构研究

以具有层状硅酸盐结构的累托石(REC)为主体,以烷基季铵盐为改性剂合成了有机累托石(OREC),以有机累托石和环氧树脂复合,制备出纳米复合材料。累托石含量在0.8wt.% 时,纳米复合材料具有最佳力学和热学性能,冲击强度增加到65.6 kJm-2,断裂伸长率从4.7 %增加到20.2 %,玻璃化转变温度提高到 197.9 ℃。用X-小角衍射法、透射电镜和红外吸收光谱研究了材料的微观结构,XRD 衍射图显示,未经处理REC 的层间距d001 = 2. 2 nm,经有机改性后,累托石片层间距扩大到2.8 nm,与环氧树脂复合后,其层间距扩大到4.2 nm 左右,FT-IR图显示,有机累托石中出现十六胺的特征吸收峰,TEM照片显示该复合材料是一种纳米复合材料。     

环氧树脂/聚砜共混体系相结构的调控研究——环氧预聚物分子量的影响

研究了不同分子量的环氧预聚物对双酚A型双官能团环氧树脂 /聚砜 (PSF) /固化剂 (二氨基二苯基砜 ,DDS)体系相分离结构的影响 .通过红外光谱 (FTIR)和动态热机械分析 (TMA)对反应转化率、玻璃化温度以及固化温度的关系的研究 ,表明环氧预聚物分子量较小时 ,凝胶点和玻璃化是影响相结构的关键因素 ;环氧分子量较大时 ,环氧扩链后粘度的变化则成为抑制相分离的重要因素 .电子显微镜 (SEM)结果表明改变环氧预聚物分子量可以达到调控相结构的目的 ,随着预聚物分子量的增大 ,体系的微区尺寸减小 .     

插层聚合制备粘土/环氧树脂纳米复合材料过程中粘土剥离行为的研究

用ＸＲＤ、ＤＳＣ 等手段研究了有机蒙脱土在环氧树脂中的插层与剥离行为,证明环氧树脂容易插层到粘土片层间,形成稳定的插层混合物,加入胺固化剂固化后,粘土被剥离而得到剥离型纳米复合材料,剥离程度与所采用的固化温度关系不大,主要取决于固化程度,全部剥离的时间与环氧树脂凝胶的时间接近．     

反应诱导相分离过程的超声波在线跟踪

利用高频超声波对多相体系的界面Rayleigh散射作用实现了反应诱导相分离过程的在线跟踪.新技术用来跟踪环氧树脂在聚乙二醇介质中的固化反应,研究体系在不同浓度、不同反应介质、不同固化剂用量以及不同反应温度下的相分离过程.在对旋节线相分离模式深入分析的基础上,提出了双函数模型来描述相分离过程.将超声波散射强度与相分离速率函数以及相离散速率函数相结合,所得到的数学模型合理解释了超声波跟踪数据.跟踪技术发现,反应体系的浓度对相分离的速率和相结构的离散程度有很大影响,高浓度下的固化反应抑制了相分离,使相结构保持高的连续性;在高浓度和PEG2000介质中发现了l(t)滞后现象,证明了旋节线相分离的分离机理;环氧树脂与固化剂重量比为4/1时,相分离达到最佳状态;升高反应温度,固化反应速率提高快于相分离速率的提高,相分离被固化反应所抑制.新的技术将散射强度与微相结构中的离散程度对应起来,从而能实时分析相分离过程中微相结构的变化过程,为相分离的控制提供实验依据.     

基于甲壳型液晶高分子的刚-柔型二嵌段共聚物的层状相:链伸展行为的研究

研究了一系列以聚己内酯(PCL)为柔性链段、甲壳型液晶高分子聚{2,5-二[(4-甲氧基苯基)氧羰基]苯乙烯}(PMPCS)为刚性链段的刚-柔型二嵌段共聚物(PCL-b-PMPCS)的微相分离结构.小角X射线散射(SAXS)和广角X射线衍射(WAXD)实验结果表明,当PMPCS为无定形态时,PCL-b-PMPCS的微相分离行为与柔-柔型二嵌段共聚物相似,其相形态主要取决于两段的体积分数.随温度升高,PMPCS链段采取伸展的棒状构象,形成六方柱状向列相(ΦHN),会诱导体系的微相分离结构出现"有序-有序"或"无序-有序"转变,使得在很宽的PMPCS体积分数(fPMPCS:40%~80%)内样品均呈现层状微相分离结构.我们对在200oC得到的层状相SAXS数据进行了一维相关函数分析,详细考察了层状相中PMPCS及PCL相区的厚度(LPMPCS、LPCL)与相应链段聚合度(NPMPCS、NPCL)的关系.对PMPCS相区,发现LPMPCS=0.2NPMPCS(nm).因棒状PMPCS链段与层的法线方向平行,该线性关系表明PCL-b-PMPCS的层状相为"单层近晶A相"结构,LPMPCS即为棒状PMPCS链段的长度,可通过控制PMPCS的聚合度予以精确控制.对PCL相区,则LPCL与NPCL近似有标度关系LPCL~NPCL0.85,说明处于熔融态的PCL链段受迫强烈伸展.进一步分析WAXD实验数据并计算每根PMPCS链段在层状相中的界面面积(S/X)可知,随NPMPS增大,PMPCS链段的液晶度从~20%增至~55%,S/X则从~2.4nm2增至~2.7 nm2.与此相应,PCL链段的伸展程度会略有降低,说明LPCL有较弱的NPMPCS依赖性.另一方面,LPCL与S/X的乘积与NPCL满足线性关系LPCL(S/X)=0.21NPCL(nm3),斜率即为PCL重复单元的体积.     

固化条件对环氧树脂/丙烯酸酯橡胶共混体系结构与性能的影响

利用丙烯酸酯橡胶(ACM)提高热固性环氧树脂(EP)的韧性,系统研究共混体系固化条件对材料结构和性能的影响.研究表明,固化前环氧树脂与丙烯酸酯橡胶在整个组成范围内为均相体系,固化过程中两组份分子量不断增大,部分组成环氧树脂/丙烯酸酯橡胶共混体系(80/20及50/50)发生反应诱导相分离现象(RIPS).在发生反应诱导相分离的体系中,分相后的环氧树脂和丙烯酸酯橡胶两相彼此包含对方的组分,是一种不彻底的相分离.同时,固化后材料的结构与性能强烈依赖于所用固化条件(包括固化时间、固化温度及固化剂含量等).因此,可以通过调节体系固化条件实现对环氧树脂/丙烯酸酯橡胶共混体系结构和性能的调控.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.