尿素和甲酰胺塑化热塑性淀粉

用甲酰胺和尿素作为塑化剂制备了热塑性淀粉 (TPS) .扫描电镜显示甲酰胺和尿素混合物可以使淀粉塑化 ,形成均一的连续相 ;根据FT IR谱图可以确定 ,与甘油相比 ,甲酰胺可以使热塑性淀粉体系在保存时更稳定 ,各基团的化学环境变化更小 ,这是由于甲酰胺可以和淀粉羟基形成更稳定的氢键 .X ray衍射说明甲酰胺和尿素 (重量比为 10 % 2 0 % )作为混合塑化剂可以有效抑制淀粉的回生 ,同时防止尿素结晶析出 .在RH=33%的湿度环境保存 1周 ,这种热塑性淀粉有良好的拉伸强度、伸长率和断裂能 ,分别达到 4 83MPa ,10 4 6 %和 2 17N·m .水含量对热塑性淀粉的力学性能的影响也被研究 .另外 ,热失重实验和吸水实验说明这种热塑性淀粉的热稳定性和耐水性也要优于常用的甘油塑化热塑性淀粉     

热塑性淀粉/聚乙烯醇/蒙脱土三元纳米复合材料

用熔融挤出的方法制备了甘油塑化热塑性淀粉（TPS）/聚乙烯醇（PVA）/蒙脱土（MMT）纳米复合材料,添加蒙脱土和聚乙烯醇用以提高热塑性淀粉材料的力学性能。 在相对湿度50%的条件下,复合材料的XRD衍射谱图和透射电子显微镜测试表明,MMT以剥离状态均匀分布在TPS/PVA基体中;力学测试表明,当MMT的质量分数从0％增至5％时,复合材料的力学性能明显提高。 当蒙脱土的质量分数为3%时,复合材料最大抗张强度达到13.24 MPa,杨氏模量达到61.46 MPa。 这说明蒙脱土在复合材料中可以起到物理交联点的作用,提高了复合材料的力学性能。     

聚甲基乙撑碳酸酯/氧化石墨烯纳米复合材料的制备及性能研究

本文采用改进Hummers法制备氧化石墨烯(GO),通过原子力显微镜对GO片层形貌进行表征;以聚甲基乙撑碳酸酯(PPC)、聚乙烯醇(PVA)和氧化石墨烯(GO)为原料,采用溶液和熔融共混法相结合,制备PPC/PVA/GO纳米复合材料,研究其力学性能、热学性能和动态流变行为。结果表明,当GO含量为0.5 wt%时,拉伸强度达到了22.03 MPa,与纯PPC相比提高了25.8%;当GO含量增大到1.0 wt%时,拉伸强度开始降低;断裂伸长率随GO的加入呈现降低的趋势。GO含量为1.0%时复合材料的热学性能最好,与纯PPC相比,复合材料的完全热分解温度从350℃提高到了400℃以上,并且热分解速率下降了12%/min;复合材料的复数黏度、储能模量和损耗模量随PVA及GO的引入也有一定程度的提高。     

聚乳酸纤维对热塑性淀粉塑料性能的影响

为增强热塑性淀粉(TPS)的力学及耐水性能,通过挤出注塑工艺制备了聚乳酸纤维(PLAF)增强的TPS复合材料(PLAF/TPS)。采用万能试验机、扫描电镜(SEM)、接触角测定仪、热重分析仪(TG)和转矩流变仪对PLAF/TPS复合材料的性能进行了表征。结果表明:适量的PLAF能够较好地分散在TPS基体中,并与淀粉分子形成氢键,从而显著增强TPS的力学及耐水性能。当PLAF的添加量(质量分数)为1.0%时,复合材料的拉伸强度及冲击强度从纯TPS的1.98 MPa、33.45kJ/m~2提高到6.79MPa、43.71kJ/m~2,断裂伸长率有所下降;PLAF的添加能使复合材料表面的接触角由纯TPS的46.3°增加到最大88.5°,耐水性能显著改善;PLAF使TPS的热稳定性略有提高;PLAF/TPS复合材料的加工性能随着PLAF添加量的增加而变差,当PLAF添加量为1.0%时,PLAF/TPS适宜加工成型。     

甲酰胺塑化热塑性淀粉的性能研究

用甲酰胺作为塑化剂制备了热塑性淀粉 (TPS) ,扫描电镜显示甲酰胺可以使淀粉塑化 ,形成均一的连续相 ;流变性能说明在加工温度范围内 ,甲酰胺塑化淀粉 (FPTPS)的剪切应力对温度变化敏感性要小于甘油塑化淀粉 (GPTPS) ;用热重和DSC研究了热稳定性和玻璃化转变 ;FPTPS在 13%～ 2 3%的水含量时有较好的力学性能 ,水含量为 13%时 ,FPTPS有最大的断裂强度 3 9MPa ;水含量为 17%时 ,FPTPS最大的伸长率为 95 % ;与GPTPS相比 ,在RH(Relativehumidity) =0 5 0 %and 10 0 %环境下 ,FPTPS有良好的耐回生性能 ,这主要是因为甲酰胺可以和淀粉羟基形成更稳定的氢键     

醋酸淀粉/聚乳酸的制备及性能的影响研究

采用自设计的双螺杆结构挤出制备聚乳酸(PLA)/醋酸淀粉(AS)的全生物降解材料,考察材料的AS的含量和取代度对复合材料动态流变性能、机械性能的影响。研究结果表明,AS含量明显影响复合材料的力学性能、复合黏度和储能模量:当AS含量从45%增加到70%,材料的拉伸强度下降,复数黏度和储能模量则提高。随着AS取代度由1.0上升为3.0,复合材料的复数黏度和储能模量下降,拉伸强度由12.0MPa上升为15.5MPa。对复合材料进行电镜扫描分析发现,AS以海岛结构形式分散在PLA的连续相中,取代度2.0的AS与PLA相容性最好,当其质量含量达到70%,材料的拉伸强度仍然不低于10.0MPa,具有较好的机械强度。     

热塑性淀粉/乙烯-乙烯醇共聚物复合材料的制备与性能

利用熔融共混的方法,制备得到热塑性淀粉/乙烯-乙烯醇共聚物（TPS/EVOH）复合材料,并对该复合体系的加工性能、机械性能、动态力学性能、流变性能以及吸水性进行了研究.结果表明：随着EVOH含量增加,复合材料中分子间作用力加强;复合体系的机械性能得到改善;当EVOH含量到达30%后,复合材料的吸水性明显降低.     

膨胀蛭石填充聚甲醛复合材料的制备与性能

采用经硅烷偶联剂和十六烷基三甲基溴化铵有机插层处理的膨胀蛭石微粉(EV)填充改性聚甲醛(POM),通过熔融共混制备POM/EV复合材料,并讨论了EV含量对复合材料的力学性能及热稳定性的影响.研究结果表明:当EV添加量为2%(w)时,复合材料的断裂伸长率为66.2%,较纯POM提高44.5%;弯曲强度和缺口冲击强度分别为77.7 MPa和6.15 kJ/m~2,分别较纯POM降低了7.9%和2.4%.此外,当EV的添加量为5%(w)时,复合材料的结晶点较纯POM提高了1.4℃;且随着EV添加量的增加,复合材料的热稳定性越好.     

乙酰化淀粉的塑化和性能研究

以乙酰化改性淀粉为基体,甘油为增塑剂,利用哈克旋转流变仪密炼制备热塑性乙酰化淀粉.实验结果表明制备热塑性乙酰化淀粉的甘油/乙酰化淀粉配比应大于30/100(W/W),且随甘油含量增加,热塑性乙酰化淀粉的脆性降低.动态机械热分析(DMTA)显示热塑性乙酰化淀粉包含富甘油和富淀粉两相,乙酰化淀粉和甘油为部分互溶.流变学分析显示淀粉分子间作用力非常强,表现为类固态行为.同时本文对材料的热稳定性进行了初步研究.     

结合分子动力学验证PBS基共聚物和淀粉复合材料之间的相互作用

将聚乙二醇200(PEG200)或聚乙二醇400(PEG400)作为第四种单体分别和丁二酸(SA)、丁二醇(BDO)、乙二醇(EG)熔融共聚得到不同醚链长度的PEG200-PBES、PEG400-PBES共聚酯,再与改性的热塑性淀粉(TPS)共混,采用溶液混合方法,制备出固体复合材料,并且研究了引入不同醚链长度对复合材料各种性能的影响;结合分子动力学(MD)模拟分析了不同醚链长度(PEG-PBES)/TPS复合体系分子之间的相互作用.研究结果表明,随着醚链的增长,复合材料的相容性显著增加,(PEG400-PBES)/TPS复合体系的χ参数和Emix值更接近于0,内聚能密度及溶度参数值大于(PEG200-PBES)/TPS和PBS/TPS复合体系的相应值,说明PEG400-PBES与TPS有更好的相容性.同时,随着醚链的增长,复合材料拉伸强度由原来的1.86 MPa提高到8.84 MPa,断裂伸长率由25.54%提高到74.75%,热失重50%时的温度由281.68℃提高到310.53℃.     

Preparation,characterization and performances of biodegradable thermoplastic starch

A biodegradable thermoplastic starch (TPS) was successfully prepared from plasticizer ethanolamine and native cornstarch. The hydrogen bonding interaction between starch and ethanolamine was investigated using Fourier transform infrared (FT‐IR). When the ethanolamine mass content was 30%, after the ethanolamine‐plasticized thermoplastic starch (ETPS) was stored at RH 50% for 14 days, the mechanical testing showed that the maximum tensile stress of the ETPS reached 5.98 MPa, the tensile strain reached 106.52%, Young's modulus increased from 38.14 MPa of glycerol‐plasticized thermoplastic starch (GTPS) to 75.32 MPa of ETPS, and the breaking energy increased from 1.921 N·m to 2.305 N·m, which indicated that the mechanical properties of ETPS evidently excelled those of the GTPS. The effects of water contents on the mechanical properties of ETPS and GTPS were studied. A differential scanning calorimetry (DSC) analysis revealed that the low‐temperature transition and the glass transition temperature (T_g) of the ETPS were ?58 and 22°C respectively, which were lower than that of the GTPS. The ETPS effectively restrained the re‐crystallization of traditional GTPS, which was proved by the X‐ray diffraction (XRD). The scanning electron microscopy (SEM) images presented that ethanolamine made starch uniform. Copyright © 2007 John Wiley & Sons, Ltd.     

A Mixed Plasticizer for the Preparation of Thermoplastic Starch

In this paper, formamide was firstly used as plasticizer to prepare thermoplastic starch (TPS), which could suppress the retrogradation of TPS by X-ray diffractometry (XRD) and show a good flexibility, but was weaker than conventional glycerol-plasticized TPS (GPTPS). When urea was introduced into plasticizer, both the retrogradation and mechanical properties were ameliorated. The tensile stress, strain and energy break of TPS plasticized by urea (wt. 20%) and formamide (wt.10%), respectively, reached 4.83 MPa, 104.6 % and 2.17 N-m (Newton-meter) after it had been stored at relative humidity (RH) 30% for one week.     

Influence of heat treatment on electromagnetic properties of polyimide/carbon black composites

A kind of absorbing materials was prepared by hot pressing method using polyimide as matrix and carbon black (CB) as filler. The mechanical properties, the electromagnetic properties, and the thermal stability of polyimide/CB composites were studied. The results showed that the complex permittivity increased from 6.82 + 1.38i to 18.69 + 9.47i, whereas the flexural strength decreased from 108 MPa to 77 MPa, respectively, when the CB content increased from 2 wt% to 8 wt%. The reflection loss curves shifted to low frequency with increase of the thickness at the same content. The reflection loss below ?10 dB could be obtained in the X band with 6 wt% CB content and did not display significant difference before and after the heat treatment at 400°C for 5 h. When the content of CB was 8 wt%, the decomposition temperature (at 5% weight loss) increased approximately 42°C compared with pure polyimide matrix. Copyright © 2014 John Wiley & Sons, Ltd.     

High performance poly (vinyl alcohol)/cellulose nanocrystals nanocomposites manufactured by injection molding

Polyvinyl alcohol (PVA)/cellulose nanocrystals (CNCs) compounds were successfully melt-processed by injection molding. During the processing, water was involved in the system as both the dispersion medium for CNCs and the plasticizer for PVA. Meanwhile, formamide was added to prevent the evaporation of water and to co-plasticize PVA. Thermal gravimetric analysis and differential scanning calorimetry indicated the melt processing window of PVA was expanded by 40 °C. Tensile tests showed that the mechanical properties of injection-molded samples were significantly improved with the addition of CNCs. The tensile strength of the composites increased from 32 to 58 MPa, and modulus increased from 175 to 1,252 MPa when 7 wt% CNCs was added. Moreover, the volume shrinkage of PVA nanocomposites upon drying as well as their water leaching rate could be remarkably reduced in the presence of CNCs.     

聚碳酸1,2-丙二酯/蒙脱土复合材料的制备与性能

利用阳离子交换法,以十六烷基三甲基溴化铵(HTAB)改性钠基蒙脱土制备了有机改性蒙脱土(OMMT),OMMT的层间距达到了2nm,比普通的钠基蒙脱土增加了0.74nm.采用熔融插层法制备了插层-絮凝型PPC/OMMT复合材料,当复合材料中OMMT含量为5wt%时,复合材料的杨氏模量较纯PPC树脂大幅度提高了61.8%,同时玻璃化温度(Tg)提高了2.4℃,热分解温度提高了32.3℃.因此,OMMT对大幅度提高PPC的杨氏模量具有很大的潜力.     

Effect of Zinc Oxide on Morphology and Mechanical Properties of Polyoxymethylene/Zinc Oxide Composites

This paper studies the effects of zinc oxide (ZnO) on morphology and mechanical properties of pure polyoxymethylene (POM) and POM/ZnO composites. POM/ZnO composites with varying concentration of ZnO were prepared by melt mixing technique in a twin screw extruder. The dispersion of ZnO particles on POM composites was studied by scanning electron microscope (SEM). It is observed that the dispersion of ZnO particles is relatively good. The mechanical properties of the composites such as tensile strength, stress at break, Young's modulus and impact strength were measured. Increasing content of ZnO up to 4.0 wt% increases the impact strength of POM. Addition of ZnO beyond 4.0 wt% decreases the impact strength. The composites containing ZnO content greater than 2.0 wt% show increased Young's Modulus. The tensile strength and stress at break decrease with increasing ZnO content. This may be due to the compatibility between ZnO and POM.     

Morphologies and Mechanical Properties of Cis-1,4-butadiene Rubber/Polyethylene Blends

The mechanical properties and phase morphologies of cis-1,4-butadiene rubber(BR) blended with polyethylene(PE) at different blend ratios were studied. The tensile test results show that the PE exhibits excellent reinforcing capabilities towards BR. Blending BR with PE results in a remarkable enhancement of tensile strength, modulus and the elongation at break simultaneously. An increment of tensile strength from 1.11 MPa to 16.26 MPa was achieved by incorporation of 40 wt% PE in the blends. The modulus and elongation at break of 40/60 PE/BR blends are also about 5 times higher than those of the pure BR treated under exactly the same conditions. The tear test indicates that the tear strength also increases with the increase of PE content. It reaches 58.38 MPa for the 40/60 PE/BR blend, which is approximately 10 times higher than that of the pure BR. Morphological study demonstrates that the PE forms elongated microdomains finely dispersed in the BR matrix when its content is over 30 wt%, which corresponds to the remarkably enhanced mechanical properties.According to the results, reinforcement mechanism of PE toward BR dependent on the microstructure has been discussed and two different mechanisms have been proposed.     

硅烷功能化石墨烯/硅树脂纳米复合材料的制备与表征

先用乙烯基三甲氧基硅烷(A-171)和二甲肼改性并还原氧化石墨烯(GO),制备A-171功能化的石墨烯(FG).研究结果表明A-171与GO上的羟基发生了反应,以共价键连接到了石墨烯的表面;FG能在四氢呋喃中均匀分散并且剥离成厚度约为0.9 nm的单一片层,其干燥后表面呈褶皱状.然后将FG与双组分硅树脂用溶液共混法制备了FG/硅树脂纳米复合材料.运用X射线衍射、扫描电子显微镜、动态热机械分析、拉伸试验等手段分析了复合材料的形态与性能,结果表明,与未处理过的石墨烯相比,FG在复合材料中有更好的分散和更强的界面作用.含0.5 wt%FG的复合材料的拉伸强度较硅树脂提高了87.7%,玻璃化温度提高了23.9℃,失重5%时的温度也提高了20.1℃.     

Preparation and properties characterization of gallic acid epoxy resin/succinic anhydride bionanocomposites modified by green reduced graphene oxide

Graphene oxide was reduced into reducing-graphene oxide (r-GO) successfully using gallic acid (GA) as a green reducing agent. Biobased gallic acid epoxy resin (GAER) was synthesized from renewable GA, and the biobased GAER/r-GO nanocomposites and glass fiber-reinforced composites were prepared with succinic anhydride as a curing agent. The dynamic mechanical, thermal, and mechanical properties of the composites with varying r-GO contents were characterized. When the content of r-GO was 0.5 wt%, the glass transition temperature was 10.4°C higher than the pure resin system. The thermal and mechanical properties were increased with increasing r-GO content; when the r-GO content was 1.0 wt%, the initial degradation temperature was enhanced by approximately 6.8°C, the tensile and impact strengths were 34.5% and 49.1% higher, respectively, than the pure cured GAER. The impact strength of GAER was higher than that of the bisphenol A epoxy resin/SUA curing system, but the tensile strength was lower than it.