首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 109 毫秒
1.
本文采用改进Hummers法制备氧化石墨烯(GO),通过原子力显微镜对GO片层形貌进行表征;以聚甲基乙撑碳酸酯(PPC)、聚乙烯醇(PVA)和氧化石墨烯(GO)为原料,采用溶液和熔融共混法相结合,制备PPC/PVA/GO纳米复合材料,研究其力学性能、热学性能和动态流变行为。结果表明,当GO含量为0.5 wt%时,拉伸强度达到了22.03 MPa,与纯PPC相比提高了25.8%;当GO含量增大到1.0 wt%时,拉伸强度开始降低;断裂伸长率随GO的加入呈现降低的趋势。GO含量为1.0%时复合材料的热学性能最好,与纯PPC相比,复合材料的完全热分解温度从350℃提高到了400℃以上,并且热分解速率下降了12%/min;复合材料的复数黏度、储能模量和损耗模量随PVA及GO的引入也有一定程度的提高。  相似文献   

2.
壳聚糖/氧化石墨烯纳米复合材料的形态和力学性能研究   总被引:4,自引:0,他引:4  
通过溶液共混法成功制备了氧化石墨烯/壳聚糖纳米复合材料.透射电镜(TEM)结果表明,氧化石墨烯纳米粒子在壳聚糖基体中分散良好.拉伸实验结果表明,随氧化石墨烯含量的增加,氧化石墨烯,壳聚糖纳米复合材料的杨氏模量和拉伸强度均显著改善,加入4 wt%的氧化石墨烯能够使纳米复合材料的杨氏模量和拉伸强度分别提高123%和117%:但另一方面,却也在一定程度上使复合材料的断裂伸长率或韧性下降.  相似文献   

3.
首先制备可均匀分散于N,N’-二甲基甲酰胺(DMF)中的氧化石墨烯片(GO),将GO的DMF分散液与聚酰胺酸(PAA)的DMF溶液进行液相共混,然后流延成膜制得GO-PAA复合薄膜,最后将PAA进行热酰亚胺化处理,在此过程中GO被原位还原为石墨烯(GS),从而获得石墨烯-聚酰亚胺(GS-PI)复合薄膜.将具有不同石墨烯含量的复合薄膜样品分别进行热重分析及力学和电学性能测试.结果表明,随着GS含量的增加GS-PI复合薄膜的表面电阻率逐渐降低.使用1.0 wt%的GO制备的GS-PI复合薄膜的表面电阻率降至106Ω,此后趋于稳定.在GO不高于0.6 wt%的用量下制备的复合薄膜的拉伸强度和断裂伸长率可发生同步增加;至GO用量为0.6 wt%二者的增强都达到最高值.此后继续增加GS含量,拉伸模量持续提高,断裂伸长率出现下降.在实验涉及的范围内,复合薄膜保持良好的延展性和热稳定性.  相似文献   

4.
戴静  郎美东 《化学学报》2012,70(11):8-15
使用简单的溶液共混的方法制备了氧化石墨烯/聚甲基丙烯酸甲酯(GO/PMMA)和表面官能化的石墨烯/聚甲基丙烯酸甲酯复合材料.通过透射电镜(TEM),扫描电镜(SEM)和原子力显微镜(AFM)观察了石墨烯及复合材料的表观形貌.通过拉伸实验表征了其力学性能,研究发现随着石墨烯的加入,其拉伸强度和断裂伸长率都有所改善,而且表面官能化的石墨烯的复合材料的改善效果要优于氧化石墨烯.  相似文献   

5.
原位缩聚法制备碳纳米管/尼龙11复合材料   总被引:1,自引:0,他引:1  
用原位缩聚法制备了碳纳米管增强的尼龙11复合材料,用X射线衍射仪、红外(FTIR)、扫描电镜(SEM)、热重(TGA)、机械拉伸测试仪等对其结构、形貌、热性能及机械性能进行了表征测试.扫描电镜结果显示碳纳米管均一地分散在尼龙11/碳纳米管复合材料中.复合材料的拉伸模量比纯尼龙11有较大的提高.当复合材料中碳纳米管含量分别为1%,5%,10%时,材料的拉伸模量分别提高了34.5%,92.9%和113,7%.同时,复合材料的储能模量也有提高.热分析结果显示当复合材料中碳纳米管含量为1%时,其失重5%和10%的温度分别由纯尼龙11的404℃、424℃提高到414℃和437℃.示差扫描量热分析(DSC)显示复合材料的结晶温度随碳纳米管的加入而升高,而结晶度则降低.  相似文献   

6.
《电化学》2015,(4)
本文以氧化石墨烯(GO)溶液为氧化剂,采用水热法使GO直接氧化Mn(Ac)2制备Mn3O4/石墨烯复合材料,并通过在制备过程中加入氨水提高了复合材料中GO的还原程度与Mn3O4颗粒的分散性.制得的Mn3O4/石墨烯复合材料表现出优异的电化学性能.在0.5 A·g-1的电流密度下复合材料质量比容量可达到850 m Ah·g-1,0.5 A·g-1时充放电循环测试200周容量保持率为99%.  相似文献   

7.
以三聚氰胺(MA)和甲醛为原料,添加氧化石墨烯(GO),通过原位聚合法制备了环境友好的石墨烯/三聚氰胺甲醛树脂(GE/MF)纳米导电复合材料.采用傅里叶变换红外光谱(FTIR)、拉曼光谱(Raman)、X-射线衍射(XRD)及场发射扫描电子显微镜(FESEM)分析了复合材料的结构和形貌.通过高阻仪和热重分析仪研究了石墨烯对三聚氰胺甲醛树脂导电性和热稳定性的影响,并检测了其甲醛含量.结果表明,超声剥离之后的GO与三聚氰胺甲醛树脂自组装形成了"三明治"夹层结构的复合材料,在GO被还原成GE的同时,大大降低了产品中游离甲醛含量,提高了复合材料的导电性和热稳定性.  相似文献   

8.
石墨烯/聚苯胺复合材料的制备及其电化学性能   总被引:1,自引:0,他引:1  
以苯胺和氧化石墨烯(GO)为原料, 采用电化学方法制备了石墨烯/聚苯胺(GP)复合材料. 利用X射线衍射(XRD)、扫描电镜(SEM)、拉曼(Raman)光谱、X射线光电子能谱分析(XPS)对其结构、微观形貌进行了表征,并对复合材料电化学性能进行了测试. 结果表明, 复合材料保持了石墨烯的基本形貌, 聚苯胺颗粒均匀地分散在石墨烯表面, 复合材料在500 mA·g-1的电流密度下比电容达到352 F·g-1, 1000 mA·g-1下比电容为315 F·g-1, 经过1000 次的充放电循环后容量保持率达到90%, 远大于石墨烯和聚苯胺单体的比电容. 复合材料放电效率高, 电解质离子易于在电极中扩散和迁移.  相似文献   

9.
采用Hummers方法制备了氧化石墨烯(GO),并通过扫描电镜(SEM)和原子力显微镜(AFM)对GO微观形貌进行了表征.详细研究了GO与硅磷低聚物(DMS-DOPO)在环氧树脂(EP)力学性能和阻燃性能中的协同作用.万能材料试验测试结果表明,GO和DMS-DOPO分别对拉伸强度和断裂伸长率提高效果明显,二者协同后,可使EP拉伸强度和断裂伸长率分别提高17.1%和42.2%.采用热重分析(TG)、极限氧指数(LOI)、垂直燃烧(UL-94)、锥型量热(CONE)和SEM对EP及其阻燃材料的热性能、燃烧性能以及炭层微观形貌进行了表征.EP/DMS-DOPO/GO在600℃残留量为EP的5.2倍,比EP/DMS-DOPO和EP/GO分别提高4.4%和208.6%.EP/DMS-DOPO/GO的LOI值大于30,并能通过UL-94 V-0级别,燃烧过程中可形成内部结构疏松多孔、外表面致密的膨胀炭层.DMS-DOPO和GO协同后使EP热释放速率峰值由1154 k W·m-2降低到710 k W·m-2,总烟释放量降低30%.  相似文献   

10.
石墨烯自2004年发现以来,由于其独一无二的优异性迅速成为科学家们的研究热点.由于石墨烯具有极其优异的电学、力学和热学等性能,因此被广泛应用于高性能聚合物基复合材料的制备.众所周知,纳米填料在聚合物中的分散状态以及与基体间的界面作用是构筑高性能聚合物纳米复合材料的关键因素.由于石墨烯极易团聚,难以通过传统的熔融共混法制备均匀分散的石墨烯增强-聚烯烃纳米复合材料.另一方面,聚烯烃通常需要在较高温度下才能溶于部分有毒溶剂(如:三氯苯和二甲苯等),因此溶液共混法也不适用于聚烯烃-石墨烯纳米复合材料的制备.有鉴于此,本文开发了一种共沉积法制备石墨烯/二氯化镁负载钛系齐格勒-纳塔催化剂的路线.通过原位聚合直接制备出石墨烯均匀分散的聚烯烃/石墨烯纳米复合材料.考察了石墨烯的加入量对催化剂形态及其催化乙烯聚合行为的影响.当石墨烯加入量较低时,多个石墨烯片被包裹于较大的催化剂粒子中.随着石墨烯加入量的增加,催化剂趋向于在石墨烯表面聚集.继续增加石墨烯量将导致石墨烯包裹催化剂粒子,降低过渡金属钛的负载效率.通过三乙基铝活化后,所制备的催化剂具有非常高的乙烯催化活性,所生成的聚乙烯/石墨烯纳米复合材料复制了催化剂的片状结构.同时,通过对所制备的聚乙烯/石墨烯纳米复合材料进行电子显微镜和X射线衍射分析可知,石墨烯均匀分散于聚乙烯基体中,并且没有任何团聚现象发生.该复合材料的热重分析表明,仅加入非常少量的石墨烯就可以使其具有比纯聚乙烯更高的热稳定性,当石墨烯加入量为0.66 wt%时,其5 wt%热分解温度较纯聚乙烯升高了54℃.同时,所制备聚乙烯/石墨烯纳米复合材料具有更优异的机械性能.因此,本研究提供了一个简单高效的高性能聚烯烃/石墨烯纳米复合材料的制备方法.  相似文献   

11.
Highly flexible nanocomposite films of nanocrystalline cellulose acetate (NCCA) and graphene oxide (GO) were synthesized by combining NCCA and GO sheets in a well-controlled manner. By adjusting the GO content, various NCCA/GO nanocomposites with 0.3–1 wt% GO were obtained. Films of these nanocomposites were prepared using the solvent casting method. Microscopic and X-ray diffraction (XRD) measurements demonstrated that the GO nanosheets were uniformly dispersed in the NCCA matrix. Mechanical properties of the composite films were also studied. The best GO composition of the samples tested was 0.8 wt%, giving tensile strength of 157.49 MPa, which represents a 61.92 % enhancement compared with NCCA. On the other hand, the composite films showed improved barrier properties against water vapor. This simple process for preparation of NCCA/GO films is attractive for potential development of high-performance films for electrical and electrochemical applications.  相似文献   

12.
The novel polymer composite of polyvinyl alcohol (PVA), polyol(PO) and graphene oxide (GO) was used to prepare the PVA/PO and GO/PVA/PO with different weight percents of GO (0.5 and 1% denoted as (0.5 wt%)GO/PVA/PO and (1 wt%)GO/PVA/PO, respectively) through solution casting blend technique. The structure–properties of all used films were confirmed by scanning electron microscope (SEM), Transmission Electron Microscope (TEM), X-ray powder diffraction (XRD), thermogravimetric analysis (TGA) and mechanical properties. The SEM results exhibited the uniform and homogeneous dispersion of GO in the PVA/PO blend matrix. The TEM and XRD analysis confirmed the structure and exfoliation of GO nanosheets, respectively. Thermal stability suggested that (0.5 wt%)GO/PVA/PO and (1 wt%) GO/PVA/PO films are more stable than PVA/PO. The tensile strength of (0.5 wt%)GO/PVA/PO and (1 wt%)GO/PVA/PO films reached 270.5% and 1349.6%, respectively, which are higher than that of the PVA/PO film. The decrease in the water absorption (WA) of GO/PVA/PO was found from 110.5 to 38.4%. The physico-mechanical properties of used films suggested that the prepared GO/PVA/PO blend composite films can be applied in food packaging areas.  相似文献   

13.
Herein we report an easy and efficient approach to prepare lightweight porous polyimide (PI)/reduced graphene oxide (RGO) composite films. First, porous poly (amic acid) (PAA)/graphene oxide (GO) composite films were prepared via non‐solvent induced phase separation (NIPS) process. Afterwards PAA was converted into PI through thermal imidization and simultaneously GO dispersed in PAA matrix was in situ thermally reduced to RGO. The GO undergoing the same thermal treatment process as thermal imidization was characterized with thermogravimetric analysis, Raman spectra, X‐ray photoelectron spectroscopy and X‐ray diffraction to demonstrate that GO was in situ reduced during thermal imidization process. The resultant porous PI/RGO composite film (500‐µm thickness), which was prepared from pristine PAA/GO composite with 8 wt% GO, exhibited effective electrical conductivity of 0.015 S m?1 and excellent specific shielding efficiency value of 693 dB cm2 g?1. In addition, the thermal stability of the porous PI/RGO composite films was also dramatically enhanced. Compared with that of porous PI film, the 5% weight loss temperature of the composite film mentioned above was improved from 525°C to 538°C. Moreover, tensile test showed that the composite film mentioned above possessed a tensile strength of 6.97 MPa and Young's modulus of 545 MPa, respectively. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

14.
廖双泉 《高分子科学》2015,33(7):1058-1068
An effective procedure has been developed to synthesize the functionalized graphene oxide grafted by maleic anhydride grafted liquid polybutadiene(MLPB-GO). Fourier transform spectroscopy and X-ray photoelectron spectroscopy indicate the successful functionalization of GO. The NR/MLPB-GO composites were then prepared by the co-coagulation process. The results show that the mechanical properties of NR/MLPB-GO composites are obviously superior to those of NR/GO composites and neat NR. Compared with neat NR, the tensile strength, modulus at 300% strain and tear strength of NR composite containing 2.12 phr MLPB-GO are significantly increased by 40.5%, 109.1% and 85.0%, respectively. Dynamic mechanical analysis results show that 84% increase in storage modulus and 2.9 K enhancement in the glass transition temperature of the composite have been achieved with the incorporation of 2.12 phr MLPB-GO into NR. The good dispersion of GO and the strong interface interaction in the composites are responsible for the unprecedented reinforcing efficiency of MLPB-GO towards NR.  相似文献   

15.
Poly(D,L‐lactide‐co‐glycolide) 50:50 (PLGA)/graphene oxide (GO) nanocomposite films were prepared with various GO weight fractions. A significant enhancement of mechanical properties of the PLGA/GO nanocomposite films was obtained with GO weight fractions. The incorporation of only 5 wt% of GO resulted in an ~2.5‐fold and ~4.7‐fold increase in the tensile strength and Young's modulus of PLGA, respectively. The thermomechanical behaviors of composite films were investigated by dynamic mechanical analysis. Results indicated that the values of Tg and storage moduli of the PLGA/GO composites were higher than those of the pristine PLGA. The improvement in oxygen barrier properties of composites was presumably attributed to the filler effect of the randomly dispersed GO throughout the PLGA matrix. In this work, we also studied in vitro biodegradation behavior. PLGA/GO composite films were hydrolyzed at 37°C for periods up to 49 days. Because of the presence of GO nanosheets, degradation of composite films took place more slowly with increasing GO amounts. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

16.
In the present work, graphene oxide (GO) and reduced graphene oxide (RGO) were incorporated at low‐density polyethylene (LDPE)/ethylene vinyl acetate (EVA) copolymer blend using solution casting method. Monolayer GO with 1‐nm thickness and good transparency was synthesized using the well‐known Hummers's method. Fourier transform infrared and X‐ray photoelectron spectroscopy data exhibited efficient reduction of GO with almost high C/O ratio of RGO. Scanning electron microscopy showed the well distribution of GO and RGO within LDPE/EVA polymer matrix. The integrating effects of GO and RGO on mechanical and gas permeability of prepared films were examined. Young's modulus of nanocomposites are improved 65% and 92% by adding 7 wt% of GO and RGO, respectively. The tensile measurements showed that maximum tensile strength emerged in 3 wt% of loading for RGO and 5 wt% for GO. The measured oxygen and carbon dioxide permeability represented noticeably the attenuation of gas permeability in composite films compared with pristine LDPE/EVA blend. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

17.
Graphene oxide (GO) was treated with two types of surfactants, i.e., silane coupling agent (KH550) and 4,4’-diphenylmethane diisocyanate (MDI), incorporated into phenyl silicone rubber at a low concentration (≤0.2 wt%), and cured by the room temperature vulcanized method. The effects of functional graphene oxide on the dielectric behaviour, thermal conductivity, optical transmittance and mechanical properties of the composites were investigated. The results showed that the particle size changed after modification and that the modified GO dispersed well in the phenyl silicone rubber. The composites with MDI modified GO exhibited better electrical insulation and lower light loss in the ultraviolet–visible region than the composites with KH550 modified GO. However, composites filled with KH550 modified GO present better thermal conductivity.  相似文献   

18.
To reveal the enhancement effect of graphene oxide (GO) in polymer nanofiber yarns, polyacrylonitrile (PAN)/GO nanofibers with different GO content (0.1‐0.5 wt%) were electrospun. The alignment of PAN chains and GO in nanofibers was enhanced by hot stretching of the yarn in dry conditions. The microstructure of the composite nanofiber yarns was investigated through X‐ray diffraction, polarized Fourier transform infrared spectroscopy and transmission electron microscopy. The results demonstrated that the hot stretching above Tg of PAN precursor lead to the increased orientation‐induced crystallization and alignment of PAN chain and GO. The yarn with 0.1 wt% GO and stretched by 4 times its length obtained the highest strength and modules (310.88 ± 24.68 MPa and 7.24 ± 0.55 GPa), which were 600% and 500% higher than those of the as‐electrospun pure PAN yarn. The most promising tensile properties found in hot stretched yarns with low GO content was because the strong interaction occurred between PAN molecules and oxygen‐containing functional groups. Indirect evidence of GO aggregation was also presented, which adversely affected the mechanical properties at higher GO content. Composite nanofiber yarns were sewable and weavable, and could be used as a new generation of composite reinforcement after pyrolysis.  相似文献   

19.
Poly(benzoxazine-urethane)/graphene oxide [poly(Bz-PU)/GO] composites were successfully prepared by blending benzoxazine (Bz) with graphene oxide (GO) and isocyanato (NCO)-terminated polyurethane prepolymer (PU), followed by thermally activated polymerization of the blends. The network was formed via the mutual reaction and intermolecular interaction among the hydroxyl of GO, NCO groups of PU and phenolic hydroxyl of Bz. The toughness shown from SEM images and tensile properties of polybenzoxazine (PBz) plastic composites can effectively be improved by alloying with PU and GO. The onset curing temperature and exothermic peak maximums of the polymerization obtained from differential scanning calorimetry decreased resulted from the GO addition. The thermogravimetric analysis showed that the incorporation of 0.5 wt% of GO slightly improved the thermal stability of poly(Bz-PU)/GO composites. Additionally, the storage modulus improved and the glass transition temperature (Tg) increased gradually as the increasing GO content not beyond a certain amount. Finally, the exothermic peaks of the polymerization were shifted to lower temperature, and the thermal stability increased for the ternary composites as the number average molecular weights (Mn) of polyol decreased.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号