富勒烯C60-多芳胺类衍生物选择性加成反应的研究

多芳胺是良好的电子给体,富勒烯C60作为电子受体的光诱导分子内和分子间电荷转移现象[1,2]引起人们普遍关注,尤其是设计合成长寿命电荷分离态的富勒烯C60-多芳胺基类衍生物研究[3,4]是热点课题之一.由于聚吡咯/聚芳胺的氧化还原电位较低[5],我们设想包含吡咯/芳胺给体的富勒烯C60衍生物能延长电荷分离态的寿命.本文用1,3-偶极环加成反应[6]对富勒烯C60与多芳胺化合物的选择性加成反应进行了研究,在不同条件下得到了单加成产物和三加成产物,用FAB-MS,UV-vis,IR,1H NMR,13C NMR,HPLC等方法确定了其分子结构.并且利用半经验AM1量子化学方法在理论上研究了它们的优化构型(如图1)、电子结构,结果表明,富勒烯C60-多芳胺基类衍生物的前沿轨道主要由富勒烯C60部分决定,富勒烯C60母体与功能化基团三苯胺基之间存在较强的分子内电荷转移,这为富勒烯C60衍生物作为光电分子器件材料的应用提供了理论和实验依据.     

二茂铁-酞菁-富勒烯超分子三元体系的构筑及光物理和电化学性质

采用富勒吡咯烷衍生物中的吡啶或咪唑基与二茂铁修饰的金属酞菁轴向配位构筑了二茂铁-酞菁-富勒烯超分子三元体系, 通过紫外-可见光谱滴定法测定了其配位稳定性(K_assoc约为8.58×10⁴ L/mol). 稳态和时间分辨荧光光谱研究结果表明, 在该超分子三元体系中发生了快速的光诱导电子转移(k_CS约为10⁹ s^-1), 并具有较高的电荷分离态量子产率(Ф_CS=0.88). 循环伏安法数据表明, 其电荷分离驱动力ΔG_CS为负值(-0.60 eV), 说明酞菁和富勒烯之间容易形成电荷分离态.     

热处理对聚四氟乙烯-聚苯胺系列导电复合膜性能的影响

对电化学制备的聚四氟乙烯-聚苯胺系列导电复合膜进行热处理,采用热重、红外和X衍射等手段研究了在空气和真空氛围中,热处理对复合膜的电导率及力学性能的影响。热分析结果表明：此系列复合膜在100～180°C失重较少,在此温度区间内对聚苯胺-聚四氟乙烯复合膜热处理,其电导率在空气和真空氛围中均随热处理温度升高而下降,聚苯胺-聚四氟乙烯-银复合膜在空气氛围中的电导率也随热处理温度升高而下降,两种复合膜的强度不变,断裂伸长率降低;聚苯胺-聚四氟乙烯-银复合膜在真空氛围中经120°C热处理后电导率提高最显著,力学强度也有所提高,但断裂伸长率降低。X衍射研究表明复合膜经180°C热处理后结晶度降低。红外分析结果表明聚苯胺-聚四氟乙烯复合膜经180°C热处理,发生了磺基水杨酸的脱掺杂和聚苯胺的结构热氧化、分子链的断裂和交联,复合膜电导率降低。     

异咯嗪修饰富勒烯-聚丙烯酸的合成及其与DNA的相互作用

利用自由基聚合反应合成了聚丙烯酸修饰的富勒烯(C₆₀-PAA),进一步通过酯化反应将核黄素类似物6,7-二甲基-9-(2’-羟乙基)-异咯嗪(DHIX)与C₆₀-PAA共价连接,得到C₆₀-PAA-DHIX.利用傅立叶红外光谱(FT-IR)、核磁共振氢谱(¹HNMR)、紫外-可见吸收光谱(UV-Vis)、荧光光谱对产物的化学结构进行了表征.循环伏安法表明,C₆₀-PAA-DHIX中富勒烯基团的第一还原电位要高于DHIX基团的第一还原电位.ESR实验表明C₆₀-PAA-DHIX能与N,N-二甲基苯胺发生多步光诱导电子转移反应,即DHIX基团与N,N-二甲基苯胺发生光诱导电子转移生成DHIX负离子自由基(DHIX^-·),DHIX^-·能进一步将电子传递给富勒烯生成富勒烯负离子自由基.DNA熔解曲线、紫外-可见吸收光谱和荧光光谱结果表明,C₆₀-PAA-DHIX通过沟槽结合与CTDNA作用,而C₆₀-PAA与DNA的作用较弱.无氧条件下,C₆₀-PAA-DHIX具有比C₆₀-PAA更强的DNA光损伤能力.     

磺酰脒基桥连的锌卟啉-富勒烯化合物构型对光诱导电子转移机理的影响

通过"一锅法"多组分偶联反应合成了一种新型磺酰脒基桥连的卟啉-富勒烯化合物ZnP-H-C₆₀. 该化合物具有Z式和E式2种异构体, 其中Z式异构体中含有分子内氢键. 光物理研究结果表明, 2种异构体中的卟啉与富勒烯之间都可以发生光诱导电子转移, 但其相应的电子转移机理却完全不同. 在Z式异构体中, 卟啉或富勒烯被激发后直接发生电荷分离而形成电荷分离态, 其电荷分离机理是通过氢键进行电子传递; 在E式异构体中, 由于卟啉和富勒烯之间存在空间电子相互作用, 被激发后先形成卟啉-富勒烯激基复合物, 再进一步发生电荷分离形成电荷分离态, 电荷分离通过空间电子转移实现.     

内包金属富勒烯衍生物La@C82-(C4N2H8)mHn的合成与表征

在常温、Ar气保护下研究了金属富勒烯与哌嗪(Piperazine)的反应, 并用硅胶柱分离了3种金属富勒烯衍生物. 用激光解析飞行时间质谱、紫外-可见-近红外光谱和傅里叶变换红外光谱等手段分析确定其结构分别为La@C82-C4N2H8, La@C82-C4N2H8-H8和La@C82-(C4N2H8)2-H6. 对比C60与哌嗪的反应结果发现, 与空富勒烯相比, 金属富勒烯反应活性更高, 产物加成数目更多.     

复合酸掺杂导电聚苯胺的合成及性能

采用复合酸掺杂微乳液法合成导电聚苯胺. 探讨了反应温度和掺杂剂质量比对聚苯胺性能的影响,并通过四探针、塔菲尔曲线、激光粒度分析、热重分析以及红外光谱测试技术,对聚苯胺进行了研究与表征. 结果表明,当聚合温度为15 ℃、磺基水杨酸和十二烷基苯磺酸钠的质量比为2.5∶1时,掺杂态聚苯胺电导率和溶解度达到最大值,同时具有良好的防腐蚀能力;其中电导率可达11 S/cm,在氮甲基吡咯烷酮(NMP)中溶解度可达85%;经电化学工作站测试的塔菲尔曲线可知,其腐蚀电位为-0.391 V. 热重分析表明,复合酸掺杂聚苯胺热分解温度约为440 ℃;粒径分析表明,约有90%的聚苯胺颗粒集中在50～100 nm之间.红外光谱表明,复合酸掺杂聚苯胺各主要吸收峰均向低频方向移动,说明掺杂的有效性.     

复合酸掺杂导电聚苯胺的性能研究

以苯胺为单体、过硫酸胺为氧化剂,由化学氧化聚合法在磺基水杨酸和硫酸的复合酸的水溶液中合成导电聚苯胺,并通过压片法、激光粒度分析、扫描电镜、差热分析及红外光谱对掺杂态聚苯胺的电导率、表面形貌及结构进行了研究.结果表明,复合酸掺杂聚苯胺的热稳定性比仅用硫酸掺杂聚苯胺的有了很大的提高;所得导电聚苯胺的粒度分布比较均匀(平均粒径约15.4μm);复合酸掺杂使聚苯胺分子链上的电荷呈离域化,掺杂程度提高.     

卟啉铜/CdSe纳米粒子复合膜的组装及其光学性能

采用静电自组装的方法,将带有相反电荷的水溶性卟啉--碘化三甲胺基苯基卟啉铜与CdSe纳米粒子交替沉积,制备了一种新型的有机-无机纳米复合薄膜。 紫外-可见吸收光谱表明,复合膜是逐层、均匀沉积的。 扫描电子显微镜照片显示复合膜中纳米粒子分布均匀,膜结构中缺陷少。 此外,还通过光谱手段系统地研究了该复合膜的发光性能、纳米粒子与卟啉之间的相互作用及膜的光稳定性。 研究结果发现,CdSe纳米粒子与CuTAPPI分子之间存在较强的相互作用,能产生由CuTAPPI到CdSe的光诱导电子转移。 而且,在该复合膜中CuTAPPI的光稳定性较高。     

聚苯胺水基胶体分散液及其复合物的研究 Ⅱ紫外光谱及导电性能

利用紫外可见光谱研究了聚苯胺（ＰＡｎ）在水基胶体分散液中掺杂与脱掺杂过程，证实了ＰＡｎ的掺杂与脱掺杂是完全可逆的过程．当ｐＨ＝３５时，开始脱掺杂，当ｐＨ＝６０时，脱掺杂已基本结束．ＰＡｎ颗粒的大小也对紫外光谱有影响．当聚苯胺颗粒尺寸达到纳米量级时（１００ｎｍ），复合膜光谱吸收峰明显兰移，表现出了表面效应和量子尺寸效应．聚苯胺／聚乙烯醇复合膜的电导率不仅受聚苯胺含量的影响，同时也受复合膜中聚苯胺颗粒聚集状态的影响．较小的聚苯胺颗粒，使复合膜具有较低的渗滤阈值．     

磺化碳纳米管改性聚苯胺复合材料的合成与超级电容特性

运用重氮化技术制备了水溶性磺化碳纳米管,在此基础上,以不同直径的磺化碳纳米管(1～2 nm,<8 nm,10～20 nm,30～50 nm)为载体,采用原位氧化聚合方法合成了一系列磺化碳纳米管改性聚苯胺复合材料.红外和紫外-可见光谱分析表明,聚苯胺与磺化碳纳米管之间存在π-π相互作用,并形成了电荷转移复合物;且随着碳纳...     

合成聚苯胺/碳化钨复合材料及聚合机理探讨

采用在原位聚合苯胺的反应介质中分散碳化钨(WC)的方法制备了掺杂聚苯胺/碳化钨(PANI/WC)复合物,并研究了苯胺在WC表面的聚合机理.通过扫描电镜(SEM)、透射电镜(TEM)、傅立叶红外光谱(FTIR)、拉曼光谱(Raman)和X射线衍射(XRD)对复合物进行了表征.结果表明,苯胺的聚合倾向于在WC颗粒表面进行,形成了PANI包覆WC的复合材料;WC粒子与PANI大分子之间存在强的相互作用,并且复合前后WC的晶型并未发生变化,WC的存在导致红外光谱有明显的蓝移现象,复合后在3446 cm-1处的红外吸收峰变得很弱;在拉曼光谱中,代表醌环C N键的伸缩振动峰红移了9 cm-1,并且强度也有很大程度提高.说明PANI与WC之间有化学键的作用,它们之间的化学键作用发生在C N键的N原子上.聚合反应优先在WC粒子表面进行,生成PANI包覆结构,并提出了PANI/WC复合物的形成机制.     

Effect Nd2O3 content on electrochemical performance of polyaniline/Nd2O3 composites

Polyaniline/neodymium(III) oxide (PANI/Nd₂O₃) composites were synthesized by in situ chemical oxidative polymerization method, and the new electrode materials were used for supercapacitor. The composites were characterized physically by scanning electron microscope (SEM), Fourier transform infrared spectra (FTIR) and X‐ray diffraction (XRD). SEM, IR and XRD results showed the existence of interactions between PANI and Nd₂O₃. The electrochemical capacitance performance of the composites was investigated by cyclic voltammetry, galvanostatic charge–discharge tests and ac impedance spectroscopy with a three‐electrode system in 6 M KOH solution. Cyclic voltammetry and galvanostatic charge/discharge tests proved that the addition of Nd₂O₃ enhanced the capacitance of the composites. However, the conductivity of the composites decreases with increasing the amount of Nd₂O₃. Electrochemical impedance tests manifest that the charge‐transfer resistance of the composites is smaller than that of the pure PANI, which indicates the addition of Nd₂O₃ could lower resistance and facilitate the charge transfer of the active materials. All results support that Nd₂O₃ has a significant contribution to the performance of PANI and makes the composites have more active sites for faradiac reaction and larger specific capacitance than pure PANI. Copyright © 2014 John Wiley & Sons, Ltd.     

The enhancement of the oxidation resistance of carbonyl iron by polyaniline coating and consequent changes in electromagnetic properties

In order to enhance the stability of commercially unmodified processed carbonyl iron (CI) and to prevent corrosion, CI powders were coated with polyaniline (PANI) by using surfactant-stabilized PANI colloids in chloroform. PANI coats the individual particles with a film of a few micrometres thickness. Electromagnetic properties, as well as thermal and storage stability, of polymer composites filled with pristine and PANI-coated CI have been studied. The PANI overlayer has negligible influence on the magnetic and dielectric spectra of CI-filled polymer composites at ambient temperature. However, the temperature-frequency study of complex permittivity demonstrated that the composites containing PANI-coated CI powders are characterized by temperature-independent dielectric spectra, whereas the complex permittivity of polymer composites with pristine powders drastically decreased at elevated temperature. Additionally, the thermogravimetric analysis of pristine and PANI-coated CI powders in air has shown improvement in the stability. PANI overlayer prevents the oxidation of particles and acts as corrosion protection of CI.     

Layer-by-layer self-assembled conducting polymer films at elevated pressure investigated by surface plasmon spectroscopy with electrochemistry

Polyaniline/sulfonated polyaniline (PANI/SPANI) multilayer films were fabricated using the layer-by-layer (LbL) technique. The electrochemical and optical properties of the film at elevated pressure were investigated by high-pressure surface plasmon spectroscopy combined with electrochemistry. Cyclic voltammograms of the PANI/SPANI films were performed at different hydrostatic pressure. It was found that the charge transfer currents decrease with elevated pressure. This indicates that the film becomes more compact with increasing hydrostatic pressure, which is confirmed by surface plasmon spectra, hinting at a substantial increase in the optical density.     

Influence of silver-decorated multi-walled carbon nanotubes on electrochemical performance of polyaniline-based electrodes

In this work, silver (Ag) nanoparticles were deposited on multi-walled carbon nanotubes (MWNTs) by chemical reduction while Ag-decorated MWNTs (Ag-MWNTs)/polyaniline (PANI) composites were prepared by oxidation polymerization. The effect of the Ag incorporated into the interface of the composites on the electrochemical performance of the MWNTs/PANI was investigated. It was found that highly dispersed Ag nanoparticles were deposited onto the MWNTs, and the Ag-MWNTs were successfully coated by PANI. According to cyclic voltammograms, the Ag-MWNTs/PANI exhibited significantly increased electrochemical performances compared to MWNTs/PANI and the highest specific capacitance obtained of MWNTs/PANI and 0.15 M Ag-MWNTs/PANI was 162 F/g and 205 F/g, respectively. This indicated that Ag nanoparticles that were deposited onto the MWNTs caused an enhanced electrochemical performance of the MWNTs/PANI due to their high electric conductivity, which resulted in an increase of the charge transfer between the MWNTs and PANI by a bridge effect.     

TiO_2聚苯胺复合膜的光电化学

利用电化学方法制备了TiO2 聚苯胺 (PANI)复合膜 .该膜具有比TiO2 或PANI膜更宽的吸收谱区 ,并且不同于利用聚苯胺光敏化的TiO2 膜 ,表现为两者复合材料膜的性质 .扫描电镜图表明 ,TiO2 微粒不完全覆盖着PANI膜 .根据TiO2 微粒光电流谱带的阈值能可得复盖在部分氧化态聚苯胺膜上的TiO2 微粒的禁带宽度为 3.0eV .部分氧化态聚苯胺膜的光电流谱遵循Fowler定律 ( 1/2 ～hυ成线性 ) .通过Fowler图得出部分氧化态聚苯胺的绝缘母体禁带宽度为 3.33eV ,并证实该绝缘母体为还原态聚苯胺 .从Mott Schottky图得到在 0 .0 5mol/LK3Fe(CN) 6 /K4 Fe(CN) 6 溶液中 (pH =8.52 )部分氧化态聚苯胺的平带电位为 0 .13V ,掺杂浓度为 5.3× 10 18cm- 3;TiO2 PANI复合膜的平带电位为 - 0 .6 5V ,掺杂浓度为 9.1× 10 19cm- 3.解释了TiO2 PANI复合膜的光电化学过程并描绘出其能带图 .利用TiO2 PANI复合膜能够有效地光降解苯酚溶液 .     

Synthesis, characterization and thermal analysis of polyaniline/ZrO2 composites

Conducting polyaniline-zirconium dioxide (PANI/ZrO₂) composites were synthesized by ‘in situ’ deposition technique in the presence of hydrochloric acid (HCl) as dopant by adding the fine grade powder (average particle size of approximately 20 nm) of ZrO₂ into the polymerization reaction mixture of aniline. The composites obtained were characterized by infrared spectra (IR) and X-ray diffraction (XRD) and thermogravimetric analysis (TGA). TG curves and DTG curves of the composites suggest that the thermal degradation process of PANI/ZrO₂ composites proceeds in two-steps and the composites are more thermally stable than that of the pure PANI. The improvement in the thermal stability for the composites is attributed to the interaction between PANI and ZrO₂, which restricts the thermal motion of PANI chains and shields the degradation of PANI in the composites.     

Preparation of polyaniline conductive composites with diene‐rubber or polyphenylacetylene

We describe the preparation of polyaniline (PANI‐EB) by aniline oxidation with KIO₃ and the purification of the resulting dedoped polymer by an acetone extraction step to eliminate undesired by‐products from polyaniline, which could generate some safety concerns in the application and use of PANI. Excellent homogeneous and electrically conducting composite films can be prepared from chloroform solutions of purified PANI doped with camphorsulfonic acid in presence of cis‐1,4‐polybutadiene as the film‐forming agent. These films have been characterized by FT‐IR and UV‐VIS‐NIR spectroscopy. A method to synthesisze PANI directly doped with dodecylbenzenesulfonic acid (DBSA) is also reported. DBSA‐doped‐PANI was then used to prepare composites with polyphenylacetylene (PPA) by growing homogeneous films from chloroform solution. These films were conductive and were studied by FT‐IR and UV‐VIS‐NIR spectroscopy. In view of the application of these composites as gas sensors or in “electronic noses”, a short discussion is presented about the criteria used in the selection of the chemical nature of the host polymer where doped PANI is included to confer electrical conductivity. The interaction between the molecules to be detected and the polymeric sensing surface is discussed in terms of physisorption, chemisorption and charge‐transfer‐complex formation. Copyright © 2001 John Wiley & Sons, Ltd.     

Thermal stability of several polyaniline/rare earth oxide composites (I): polyaniline/CeO<Subscript>2</Subscript> composites

Polyaniline (PANI)/CeO₂ composites were prepared by adding CeO₂ powder into the polymerization reaction mixture of aniline. Fourier transform infrared spectra (FTIR) and X-ray diffraction (XRD) were used to characterize the composites. Thermogravimetry (TG) and derivative thermogravimetry (DTG) were used to study the thermal stability of the composites. IR and XRD results show that interaction exists between PANI and CeO₂. This interaction maybe is hydrogen bonding action between the hydroxyl groups on the surface of the CeO₂ and the imine groups in the PANI molecular chains. TG–DTG analysis indicates that the thermal stability of the composites is higher than that of the pure PANI. The improvement in the thermal stability of the composites is attributed to the interaction between PANI and CeO₂, which restricts the thermal motion of PANI chains and shields the degradation of PANI in the composites.