微波消解ICP-AES测定废弃线路板中的Cu、Cr、Pb等8种元素

采用微波消解技术对废弃线路板进行消解,应用全谱直谱ICP-AES同时测定Cu、Cr、Pb、Mn、Cd、Ni、Sn和Zn的含量.研究了消解体系和谱线选择对测定结果的影响,测定了分析结果的精密度和方法的检出限和回收率.结果表明:样品分析结果的相对标准偏差小于0.5%,方法检测限范围为0.5885～5.641 μg/L,方法的加标回收率和精密度分别为95.0%～103.3%和0.1%～0.5%.该方法能够同时测定多种元素.     

X射线荧光光谱法快速测定铅铋合金中的铅、铋、金、银、铜、砷、锑、锡和碲

建立快速测定铅铋合金中铅、铋、金、银、铜、砷、锑、锡、碲含量的X射线荧光光谱法。采用自制的铅铋合金样品作为标准样品,用台式车床制样,用X射线荧光光谱法快速测定铅铋合金中各元素含量,并用α理论系数法和经验系数法相结合对基体效应进行校正。各组分校准曲线的相关系数均大于0.998,检出限为5.54～101μg/g,测定结果的相对标准偏差为0.06%～7.73%(n=9)。用该方法对3个铅铋合金样品进行分析,测定结果与参考值吻合,相对误差小于8.33%。该方法简便快捷,结果准确,能满足铅铋合金中各元素检测要求,对炉前分析具有很强的实用价值。     

电感耦合等离子体原子发射光谱(ICP-AES)法测定铁矿石中磷

采用盐酸-硝酸-高氯酸-氢氟酸前处理样品,电感耦合等离子体原子发射光谱法测定铁矿石中的磷。对磷元素的分析谱线、样品称样量等工作条件进行了优化,解决了非金属元素磷的分析谱线难选择、样品称样量影响测定准确度的技术难点;采用内标法,降低了样品基体效应及仪器波动产生的影响,提高了分析结果的精密度和准确度。利用所建立的方法快速分析了铁矿石中磷的含量,方法检出限为0.003 6mg/L,测定范围为0.012%～2%,测定结果与标准值和化学法测定结果相符,相对标准偏差(RSD,n=9)小于2%。拟定的方法和分光光度法进行比对实验,技术优势明显。     

电感耦合等离子体原子发射光谱（ICP-AES）法测定铁矿石中磷

采用盐酸-硝酸-高氯酸-氢氟酸前处理样品,电感耦合等离子体原子发射光谱法测定铁矿石中的磷。对磷元素的分析谱线、样品称样量等工作条件进行了优化,解决了非金属元素磷的分析谱线难选择、样品称样量影响测定准确度的技术难点;采用内标法,降低了样品基体效应及仪器波动产生的影响,提高了分析结果的精密度和准确度。利用所建立的方法快速分析了铁矿石中磷的含量,方法检出限为0.0036 mg/L,测定范围为0.012%~2%,测定结果与标准值和化学法测定结果相符,相对标准偏差(RSD,n=9)小于2%。拟定的方法和分光光度法进行比对实验,技术优势明显。     

干法灰化-发射光谱法测定植物样品中B和Sn

地球化学样品中的元素硼和锡属于难溶易挥发元素,湿法样品前处理技术相对较难,目前基本以一米光栅发射光谱法测定为主,其固体进样方式避免了复杂的样品前处理,实现了对地球化学样品中元素硼和锡的绿色分析。植物样品经过适宜的高温灰化后,基体成分基本一致,体积质量均发生富集现象,称取的样品灰分成分和基物、缓冲剂(比例1:1:2)经过研磨充分混匀,在优化的实验条件下,以国家一级合成硅酸盐光谱分析标准物质制作校准曲线,构建植物样品中硼和锡的分析方法,该方法硼和锡的检出限分别为0.042μg·g-1、0.019μg·g-1,方法经过国家一级标准物质验证,硼方法精密度:5.6%~13%,正确度(RE)的绝对值均小于10%;锡方法精密度:7.2%~18%,正确度(RE)的绝对值均小于28%。实验结果表明:植物样品经过干法灰化富集后,对植物样品中元素硼基本能够实现精准测定,对元素锡含量接近于检测下限的值测定结果相对较差,对高含量值也能够实现精准测定,方法具有较好的应用价值。     

X射线荧光光谱法测定金红石中主次组分

采用Li2B4O7和LiBO2的混合熔剂(67∶33)熔融制样,波长色散X射线荧光光谱法测定金红石中TiO2,TFe,P,SiO2,Al2O3,MnO,CaO,Cr2O3,MgO,ZrO2,HfO2等组分。实验中样品和熔剂的质量比为1∶14,以溴化锂(LiBr)作脱模剂,采用高频熔炉在1 150℃熔融90s进行制样,所得熔片均匀、强度高、成型良好。方法用于金红石实际样品的测定,结果同参考值或化学分析方法的结果相吻合,相对标准偏差(RSD,n=10)P为3.8%、Al2O3为2.8%,其它均小于2%,能够满足实际测定工作的需要。     

火试金重量法测定铅冰铜中的金和银

建立火试金重量法测定铅冰铜中金和银的方法。探讨了氧化铅用量、灰吹温度、第一次分金酸度、干扰元素对金和银测定结果的影响。金测定结果的相对标准偏差为0.51%~2.85%(n=6),样品加标回收率为98.4%~102.7%;银测定结果的相对标准偏差为0.89%~3.01%(n=6),样品加标准回收率为97.2%~103.4%。该方法具有受干扰元素影响小、测量范围广、测试时间短等优点,适合批量测定铅冰铜中的金和银。     

高纯四氯化锗测试样品的采集和制备方法研究

针对光纤级高纯四氯化锗(99.999999%)中痕量含氢杂质吸收峰红外透过率检测(FTIR)用试样的采集,以及痕量金属杂质的电感耦合等离子体质谱法(ICP-MS)测定用试样的制备方法进行了系统研究。设计开发了用于检测痕量含氢杂质吸收峰红外透过率的样品采集实验装置,实现了含氢杂质(如—OH、—CH、HCl等)吸收峰的红外透过率在线连续测试,试样采集过程全密闭进行,避免了采样过程的二次污染,采样过程流程简短,操作简便;实验优选了在制备ICP-MS法测定痕量金属杂质用的试样过程中消除四氯化锗基体干扰、防止砷等易挥发杂质损失以及防止样品处理过程污染试样的制样方法,实现了试样制备过程二次污染源的有效控制,制样过程试剂消耗量少,制备时间短,待测元素无损失。     

高纯四氯化锗测试样品的采集和制备方法研究

针对光纤级高纯四氯化锗(99.999999%)中痕量含氢杂质吸收峰红外透过率检测(FTIR)用试样的采集,以及痕量金属杂质的电感耦合等离子体质谱法(ICP-MS)测定用试样的制备方法进行了系统研究。设计开发了用于检测痕量含氢杂质吸收峰红外透过率的样品采集实验装置,实现了含氢杂质(如—OH、—CH、HCl等)吸收峰的红外透过率在线连续测试,试样采集过程全密闭进行,避免了采样过程的二次污染,采样过程流程简短,操作简便;实验优选了在制备ICP-MS法测定痕量金属杂质用的试样过程中消除四氯化锗基体干扰、防止砷等易挥发杂质损失以及防止样品处理过程污染试样的制样方法,实现了试样制备过程二次污染源的有效控制,制样过程试剂消耗量少,制备时间短,待测元素无损失。     

不同前处理制样方法对钢中氧、氮测定结果的影响

讨论了不同物理和化学制样方法对钢中氧、氮测定结果的影响。试验结果表明,物理制样采用锉刀打磨样品表面后剪切,再用乙醚清洗除去油污;化学制样先用20%盐酸溶液溶解样品表面氧化层,再用滴加了4滴30%过氧化氢的10%草酸溶液浸泡,取出后依次用水、无水乙醇浸洗,风干。用以上两种方法制样,钢标准样品中氧、氮含量测定值与标示值一致。在测定钢中氮含量时,可用乙醚清洗后直接测定,以缩短检测周期和减轻劳动强度。该研究结果可用于指导钢样品中氧、氮含量测定时样品的处理。     

Multielement analysis of whole blood by high resolution inductively coupled plasma mass spectrometry

An analytical method using double focusing sector field inductively coupled plasma mass spectrometry (ICP-SMS) for rapid simultaneous determination of 50 elements in digested human blood is described. Sample preparation consisted of microwave digestion with nitric acid followed by dilution with ultrapure water. The importance of controlling possible contamination sources at different sample preparation and analysis stages in order to achieve adequate method detection limits (MDL) is emphasised. Correction for matrix effects was made using scandium, indium and lutecium as internal standards. Accuracy of the data for elements suffering from spectral interferences was improved by applying either a high resolution capability of the ICP-SMS or mathematical corrections. Different approaches for accuracy assessment in blood analysis are evaluated. Additional information on trace elements concentration in selected blood reference materials is given. The between-batch precision was assessed from replicate analysis (including sample preparation) of reference materials and was better than 10% RSD for 21 elements and better than 30% RSD for 36 elements under consideration. A statistical summary for results obtained for 31 blood samples from non-exposed subjects is presented. The majority of elements tested was found in the samples at concentrations higher than MDL.     

Multielement analysis of whole blood by high resolution inductively coupled plasma mass spectrometry

An analytical method using double focusing sector field inductively coupled plasma mass spectrometry (ICP-SMS) for rapid simultaneous determination of 50 elements in digested human blood is described. Sample preparation consisted of microwave digestion with nitric acid followed by dilution with ultrapure water. The importance of controlling possible contamination sources at different sample preparation and analysis stages in order to achieve adequate method detection limits (MDL) is emphasised. Correction for matrix effects was made using scandium, indium and lutecium as internal standards. Accuracy of the data for elements suffering from spectral interferences was improved by applying either a high resolution capability of the ICP-SMS or mathematical corrections. Different approaches for accuracy assessment in blood analysis are evaluated. Additional information on trace elements concentration in selected blood reference materials is given. The between-batch precision was assessed from replicate analysis (including sample preparation) of reference materials and was better than 10% RSD for 21 elements and better than 30% RSD for 36 elements under consideration. A statistical summary for results obtained for 31 blood samples from non-exposed subjects is presented. The majority of elements tested was found in the samples at concentrations higher than MDL. Received: 23 November 1998 / Revised: 6 January 1999 / Accepted: 12 January 1999     

全谱直流电弧发射光谱法同时测定钼样品中17种杂质元素

为了解决现有测定方法中样品前处理复杂、测定过程繁琐的问题,研究了直流电弧发射光谱法测定钼样品中Al、Bi、Ca、Cd、Co、Cr、Cu、Fe、Mg、Mn、Ni、Pb、Sb、Si、Sn、Ti、V等17种元素的方法。用石墨粉(98%)、碳酸钠(1%)和氟化钠(1%)作为光谱缓冲剂抑制基体元素蒸发、稳定弧焰、促进杂质元素的蒸发;采用样品装满电极后下压2 mm和滴加蔗糖乙醇水溶液(2%)的方式,防止喷溅的发生,稳定激发过程,减小基体干扰;对挥发难易程度不同的元素采用信号分段采集的方式,提高各元素信噪比。方法灵敏度高、分析速度快、操作简便,加标回收率为85%~120%,各元素分析精密度均小于15%。     

八极杆碰撞/反应池(ORS)-电感耦合等离子体质谱(ICP-MS)法测定复杂矿物中的稀土元素

对未知复杂矿物样品采用扫描电子显微镜-能谱法解析样品,确定基本成分后选择合适的样品前处理方法。实验中采用过氧化钠熔融法熔解样品,用水浸出,硝酸酸化后制备待测样品溶液。以Rh为内标,用八极杆碰撞/反应池(ORS)-电感耦合等离子体质谱(ICP-MS)法测定了复杂样品中的稀土元素。多次测定同一混合标准溶液结果的相对标准偏差(RSD,n=11)小于4%,加标回收率为90%~110%。方法适用于未知复杂矿物中稀土元素的测定。     

微波消解-ICP-AES法测定化妆品中8种有毒元素

采用微波消解-电感耦合等离子体发射光谱法(ICP-AES)对化妆品中Ba、Pb、Cd、Sb、Se、Cr、Hg、As8种有毒元素进行同时测定,通过试验确定了仪器参数和各元素的分析线。8种元素的浓度在0～10mg/L均与响应值呈线性关系,相关系数大于0.9995。8种元素测定结果的相对标准偏差均小于10%(n=3),方法检测限小于0.04mg/kg。样品中各元素的加标回收率为82.1%～108.7%。该方法适用于大批量的化妆品检测。     

Determination of trace elements in biological materials using tetramethylammonium hydroxide for sample preparation

A method to prepare milk powder, bovine liver and bovine muscle samples for analysis by electrothermal atomic absorption spectrometry (ETAAS) is proposed. Samples are mixed with a small amount of tetramethylammonium hydroxide (TMAH) and a stable and homogeneous slurry is produced in ca. 2 h with heating at 60–70 °C. After such sample preparation and dilution with water, trace elements are determined in certified reference materials. Pyrolysis and atomisation temperatures are optimised for each element, and several modifiers are investigated. External calibration is used for every analyte. Limits of detection (LODs), precision and accuracy are reported for Cd, Pb, Ni, Cr, Cu and Ag and compared with those obtained after conventional acid digestion. The main advantages of the proposed method are the simplicity of sample preparation and the longer lifetime of the graphite tube.     

Liquid chromatographic determination of carotenoids and vitamins A and E in multivitamin tablets

Carotenoids and vitamins A and E in multivitamin tablets can be determined simultaneously by reversed-phased liquid chromatography (LC) with a programmable UV detector. Samples were dissolved in dimethyl sulfoxide and then extracted with hexane. A portion was injected onto a Symmetry C18, 150 x 4.6 mm id, 5 microns column and chromatographed with a mobile phase of acetonitrile--0.25% ammonium acetate in methanol and 0.05% triethylamine in dichloromethane. A step gradient was used. The system was operated at 25 degrees C with a flow rate of 1.5 mL/min. UV detection was at 325 nm for retinols, 285 nm for tocopherols, and 450 nm for carotenoids. Detection limits were less than 0.3 ng for retinol and retinyl acetate; 2 ng for alpha-tocopherol acid succinate; 10 ng for alpha-tocopherol, gamma-tocopherol, and alpha-tocopherol acetate; and 0.4 ng for alpha-carotene and beta-carotene. Intraday and interday coefficients of variation ranged from 1.40 to 5.20%. The sample preparation method and LC assay are practical for quality control and routine analysis of multivitamin tablets.     

微波消解-ICP/MS测定烤烟中微量元素含量

以3 mL HNO3和2 mL H2O2的混合消解液对烟草样品进行微波消解,采用电感耦合等离子体质谱测定了烤烟中的Mn、Zn、Cu、Se、N i、Co、Cr、As、Cd、Pb 10种微量元素的含量.结果表明：方法的检出限均低于0.02μg/g,各元素测定的RSD（n=5）均小于3%,样品加标回收率为97.35%-101.30%.方法消耗试剂少,快速准确,适合烟草中多种微量元素的同时测定.     

Determination of refractive and volatile elements in sediment using laser ablation inductively coupled plasma mass spectrometry

Wet-milling protocol was employed to produce pressed powder tablets with excellent cohesion and homogeneity suitable for laser ablation (LA) analysis of volatile and refractive elements in sediment. The influence of sample preparation on analytical performance was also investigated, including sample homogeneity, accuracy and limit of detection. Milling in volatile solvent for 40 min ensured sample is well mixed and could reasonably recover both volatile (Hg) and refractive (Zr) elements. With the exception of Cr (−52%) and Nb (+26%) major, minor and trace elements in STSD-1 and MESS-3 could be analysed within ±20% of the certified values. Comparison of the method with total digestion method using HF was tested by analysing 10 different sediment samples. The laser method recovers significantly higher amounts of analytes such as Ag, Cd, Sn and Sn than the total digestion method making it a more robust method for elements across the periodic table. LA-ICP-MS also eliminates the interferences from chemical reagents as well as the health and safety risks associated with digestion processes. Therefore, it can be considered as an enhanced method for the analysis of heterogeneous matrices such as river sediments.     

TXRF法测定松花粉中的9种生命元素

建立了微波消解前处理,全反射X射线荧光法(TXRF)同时测定松花粉中K、Ca、Ti、Mn、Fe、Ni、Cu、Zn和Rb9种生命元素含量的分析方法.松花粉原料经过微波消解前处理后,采用全反射X射线荧光光谱净计数、QXAS分析软件解谱和单一内标法进行定量分析.比较了干灰化法、湿消解法和微波消解法3种前处理方法的效果,并确立微波消解法作为样品前处理方法.用微波消解- TXRF法测定了花粉标准物质中的上述9种元素,并计算得到其仪器检出限(LLD)为0.002～0.054 mg/L,方法检出限(LDM)为0.004～0.122 mg/kg.TXRF法测定各元素的相对标准偏差(RSDs)为1.0％～5.5％.该方法操作简单、样品用量少、检出限低,对实际样品松花粉的测定结果与ICP - MS法无显著性差异.