有机磷神经毒剂分子印迹聚合物的模拟模板分子

采用DFT/B3LYP-D3(BJ)/6-31G(d,p)计算模拟方法分析探讨了双(对硝基苯基)磷酸酯(BNPP)替代对氧磷(PO)用作有机磷神经毒剂分子印迹聚合物(MIPs)模板分子模拟物的可行性. 通过对比BNPP和PO两种模板分子分别与各种功能单体形成的复合物的构型稳定性和结合能大小, 确认了以4-甲基丙烯酰胺基安替比林(MAAP)为第一功能单体、 甲基丙烯酸(MAA)为第二功能单体组成的双功能单体体系是最佳功能单体体系. 以BNPP为模板分子、 MAAP-MAA为单体体系、 乙二醇二甲基丙烯酸酯(EGDMA)为交联剂、 纳米二氧化硅为载体, 采用表面印迹技术制备了SiO₂@BNPP分子印迹聚合物, 并对聚合物的表面形貌和吸附性能进行了分析. 实验结果表明, 当n(BNPP)/n(MAAP)/n(MAA)/n(EGDMA)为1∶1∶4∶20时, MIPs的吸附容量最大可达19.03 mg/g, 对4-硝基苯酚(4-NP)的分离因子为17.50; MIPs能够快速吸附模板分子, 5 min即可达到吸附平衡量的92%, 动态吸附平衡时间仅为15 min, 重复使用5次后仍能保持良好的吸附能力; 吸附过程符合准二级动力学模型和Langmuir等温吸附模型, Scatchard方程分析表明MIPs中存在两类吸附作用位点. 实验结果与计算模拟结果的一致性表明, 计算模拟对有机磷神经毒剂MIPs的设计和研究具有一定的指导意义.     

谷胱甘肽分子印迹聚合物的制备及其性能研究

采用新型光源高压汞灯制备了三肽分子谷胱甘肽的分子印迹聚合物(MIPs), 反应时间缩短, 制备条件温和. 对MIPs做了一系列的静态吸附实验, 结合荧光测定法研究了不同单体-模板比例下MIPs表现出来的吸附性能. 对最佳比例制备的MIPs进行了一系列性能研究, 包括吸附等温线的测定、Scatchard分析以及薄层色谱分离实验等. 结果表明, 所合成的MIPs对GSH具有良好的吸附和选择识别能力,最大吸附量为45.4 mg/g, 特异因子达到了4.98.     

谷胱甘肽分子印迹聚合物的制备及其性能研究

采用新型光源高压汞灯制备了三肽分子谷胱甘肽的分子印迹聚合物(MIPs),反应时间缩短,制备条件温和.对MIPs做了一系列的静态吸附实验,结合荧光测定法研究了不同单体-模板比例下MIPs表现出来的吸附性能.对最佳比例制备的MIPs进行了一系列性能研究,包括吸附等温线的测定、Scatchard分析以及薄层色谱分离实验等.结果表明,所合成的MIPs对GSH具有良好的吸附和选择识别能力,最大吸附量为45·4mg/g,特异因子达到了4·98.     

酮洛芬分子印迹拆分及分离过程热力学研究

利用非共价分子印迹法,采用4-乙烯基吡啶为功能单体,以二甲基丙烯酸乙二 醇酯为交联剂,在模板分子（S）-酮洛芬的存在下,制备出（S）-酮洛芬的分子印 迹聚合物（MIPs）,并用作HPLC固定相,对其进行了高效液相色谱评价。结果表明 外消旋酮洛芬在制备的印迹柱上得到了有效的分离,（S）-酮洛芬的容量因子 k_s'为9.52,选择性因子α为1.52,分离度R为0.88。此外,HPLC分析表明制备的 MIPs能够分离结构相似的酮洛芬、布洛芬和萘普生。研究了流动相中乙酸浓度、流 速及温度对拆分效果的影响,测定了分离过程中的焓变、熵变和自由能变化,对分 子印迹分离过程作了进一步解释。     

紫外光聚合法制备L-DBTA手性分子印迹聚合物的研究Ⅱ.聚合物性能

以丙烯酸为功能单体,二苯甲酰-L-酒石酸(L-DBTA)为模板分子,三羟甲基丙烷三丙烯酸酯(TMPTA)为交联剂,采用紫外光聚合方法合成了L-DBTA手性分子印迹聚合物.通过HPLC表征,表明合成的手性分子印迹聚合物对L-DBTA模板分子具有很好的识别性,L-DBTA的选择性比二苯甲酰-D-酒石酸(D-DBTA)高.通过Scatchard分析表明,L-DBTA手性分子印迹聚合物中只存在一类影响聚合物识别能力的结合位点.293.15K时,结合位点的平衡离解常数为0.064mmol/L,最大表现结合容量为6.4mg/g.MIPs结合热力学研究表明,印迹分子L-DBTA与分子印迹聚合物手性识别基团之间的识别机理可以用Langmuir等温吸附描述,结合热力学参数为△H=7.40 kJ/mol,△S=42.74 J/(mol·K),△G298=-5.34kJ/mol.L-DBTA与MIPs相互作用速率快,表观活化能为7.40 kJ/mol.     

亲水性分子印迹聚合物的制备及其在天麻素分析检测中的应用

以天麻素为模板分子,α-1-烯丙基-2-N-乙酰胺基葡萄糖为新型亲水性功能单体,N,N'-亚甲基双丙烯酰胺为交联剂,合成了对天麻素有高选择性的亲水性分子印迹聚合物(MIPs)。吸附结果表明,MIPs能够特异性识别天麻素。对MIPs吸附剂性能的考察证明,亲水性天麻素MIPs可作为固相萃取(SPE)吸附剂分离纯化天麻素。方法验证实验显示了良好的回收率(90.4%~97.1%)和精密度(3.3%~5.2%,n=5)。该文以新型亲水性功能单体为基础,建立了天麻素的分子印迹固相萃取样品前处理方法。     

琥乙红霉素分子印迹聚合物微球的制备及表征

以琥乙红霉素为模板分子,甲基丙烯酸为功能单体,乙二醇二甲基丙烯酸酯为交联剂,采用悬浮聚合法制备得到了平均粒径约为60μm的琥乙红霉素分子印迹聚合物微球(MIPs),并用扫描电镜对其表面形貌进行了表征。考察了琥乙红霉素分子印迹聚合物的印迹效果,研究了琥乙红霉素分子印迹聚合物的动力学吸附特性。比较了MIPs对琥乙红霉素及其它3种抗生素的吸附情况。结果表明,制备得到的琥乙红霉素分子印迹聚合物微球对琥乙红霉素具有最好的吸附能力,显示出MIPs具有高的选择性。     

苏丹红Ⅰ分子印迹聚合物分子识别特性的波谱分析

以苏丹红Ⅰ为模板分子,α-甲基丙烯酸为功能单体,乙二醇二甲基丙烯酸酯为交联剂,通过沉淀聚合法合成了高选择性的分子印迹聚合物。通过静态吸附实验研究了聚合物的吸附性能,采用紫外光谱(UV)和核磁共振氢谱(1 H NMR)法研究了聚合物的识别机理。实验结果表明:模板分子和功能单体之间的作用为分子间氢键;红外(IR)光谱研究进一步表明,印迹聚合物通过非共价氢键作用特异性地识别模板分子。     

酸性染料分子表面印迹材料的设计与制备及其分子识别特性研究

本文使用"接枝交联聚合与印迹过程同步进行"的分子表面印迹方法,以阳离子单体丙烯酰氧乙基三甲基氯化铵(DAC)为功能单体,以活性艳红X-3B(RBR)为模板分子,制备了酸性染料分子表面印迹材料,并考察了印迹材料的分子识别性能。在水溶液中,凭籍强静电相互作用与阳离子-π相互作用,阳离子单体DAC自动地结合在模板RBR分子周围,在氨基/过硫酸盐表面引发体系作用下,DAC及交联剂N,N'-亚甲基双丙烯酰胺(MBA)在硅胶微粒表面发生接枝交联聚合,制得了酸性染料分子表面印迹材料MIP-PDAC/SiO2。该分子表面印迹材料对RBR分子具有高度的识别选择性,相对于结构与RBR相似的活性黄X-RG和活性嫩黄X-6G两种酸性染料,MIP-PDAC/SiO2对RBR的识别选择性系数分别为8.1和8.9。     

TNT分子印迹聚合物微球的合成与性能研究

以三硝基甲苯(TNT)为模板分子,EDMA为交联剂,采用沉淀聚合法制备了TNT分子印迹微球.讨论了溶剂用量、模板分子用量、功能单体种类等对分子印迹微球的形貌及吸附性能的影响;利用紫外吸收光谱和BET表征了印迹聚合物微球的结合位点相互作用与印迹孔穴结构;通过平衡吸附和选择性吸附实验,研究了印迹聚合物微球的吸附性能和选择性识别性能.结果表明,以丙烯酰胺为功能单体制备的分子印迹聚合物为规则的球形,内部含有分子印迹孔穴,微球的粒径为1～2μm.印迹聚合物微球可在30 min内达到吸附平衡,在1 mmol/L的TNT乙醇溶液中,印迹聚合物微球的平衡吸附量为32.5 mmol/kg,对TNT分离系数为25.19,具有较好的特异性吸附能力,并可选择性识别TNT分子.     

Preparation and characterization of imprinted monolith with metal ion as pivot

This report provided the first example of using pivot concept to prepare monolithic molecularly imprinted polymers (MIPs) with ketoprofen (KET) imprints, in which metal ions were employed as mediator between the functional monomer and the template to achieve higher fidelity of imprint. To solve metal ions in pre-polymerization system, a new ternary porogen of dimethyl sulfoxide-toluene-isooctane was developed for preparation of MIP monoliths with high porosity and good permeability. The effect of polymerization parameters such as the nature of metal ions, the ratio of template to metal ion and the degree of crosslinking, on the permeability, morphology and affinity of the metal ion mediated MIP monolith were studied. The experiments demonstrated that Ni(2+), Co(2+) and Zn(2+) can be applied as pivot to prepare KET-imprinted monolith. Relative to monolithic MIP without metal ions, all the ion-mediated macropore MIP monoliths showed enhanced permeability, capacity factor and selectivity factor. High permeability (1.06×10(-7)mm(2)) was obtained on the Co(2+)-mediated MIP monolith and great selectivity factor (3.84) was achieved on the Ni(2+)-mediated one. The stoichiometric displacement model was constructed to investigate the recognition mechanism of metal-ion mediated MIP. The results indicate that metal ion as pivot not only improves the affinity but also allows the fine-tuning on the macroporous structure of MIP monolith.     

三甲氧基苄啶分子印迹整体柱的制备及色谱性能

选择甲基丙烯酸为功能单体\, 甲基丙烯酸乙二醇双酯为交联剂, 制备了三甲氧基苄啶分子印迹整体柱, 对整体柱材料的形貌进行了表征, 并且研究了TMP和5种磺胺类药物在分子印迹整体柱上的色谱行为.     

Synthesis and Molecular Recognition of Molecularly Imprinted Polymer with Ibuprofen as Template

Ibuprofen and ketoprofen are chemically similar non‐steroidal anti‐inflammatory drugs widely used in the treatment of arthritis. Using a molecular imprinting technique, a simple and rapid method was developed for the simultaneous separation and determination of ibuprofen and ketoprofen. Molecular imprinting introduces artificial binding sites into a synthetic polymer matrix, allowing it to exhibit selective rebinding of template molecules. Imprinted polymers can be regarded as an HPLC stationary phase, important for pharmaceutical analysis. Most molecularly imprinted polymers (MIPs) are synthesized by free radical polymerization of functional monomers, resulting in an excess of crosslinking monomers. In this study, MIPs have been prepared with a ibuprofen template, which can form intramolecular hydrogen bonds. Methacrylic acid (MAA) and ethyleneglycol dimethacrylate (EGDMA) were used as the functional monomer and cross‐linker, respectively. Bulk polymerization was carried out at 4 °C under UV radiation. The resulting MIP was ground into 25?44 μm particles, which were slurry‐packed into analytical columns. Template molecules were removed by methanol‐acetic acid (9:1, v/v). We evaluated the template binding performance of the MIP using HPLC, with ultraviolet (UV) detection at 234 nm. Chromatographic resolution of ibuprofen and ketoprofen on the MIPs were appraised using buffer/acetonitrile (45/55, v/v) as the mobile phase. Results show that the MIPs prepared using ibuprofen as the template had a significant molecular imprinting effect. The method was successfully applied to the separation and analysis of ibuprofen and ketoprofen in pharmaceuticals.     

Low cross-linked molecularly imprinted monolithic column prepared in molecular crowding conditions

Molecular crowding is a new approach to promoting molecular imprinting more efficiently. In this work, this concept was applied to the preparation of low cross-linked imprinted polymers in the presence of an immobilised template for stabilizing binding sites and improving molecular recognition. An imprinted monolithic column was synthesized using a mixture of 2,4-diamino-6-methyl-1,3,5-triazine (template), 2,4-diamino-6-(methacryloyloxy) ethyl-1,3,5-triazine (polymerisable template), methacrylic acid, ethylene glycol dimethacrylate, and polystyrene (molecular crowding agent). Some polymerization factors, such as template-monomer molar ratio, the composition of the porogen and crosslinking density, on the imprinting effect of resulting MIP monolith were systematically investigated. The results indicated that the imprinted monolithic columns prepared in the presence of molecular crowding agent retained affinity and specificity for template even when prepared with a level of cross-linker as low as 9%. Moreover, a stoichiometric displacement model for retention was successfully applied to evaluate the interaction between the solute and the stationary phase. Compared with the low cross-linked MIP prepared by conventional polymerization, the molecular crowding-based low cross-linked monolithic MIPs showed higher selectivity. The results suggested that molecular crowding is a powerful strategy to increase the effect of molecular imprinting at a low level of crosslinker.     

Separation of Epigallocatechin Gallate from Natural Plant Extracts Using Crowding Agents—Assisted Imprinted Polymers

A methodology-based molecularly imprinted polymer (MIP) was proposed to separate epigallocatechin gallate (EGCG) from natural plant extracts. A molecular crowding agent was introduced to improve the affinity and recognizing ability of EGCG in the preparation of an MIP monolith. Acrylamide was used as the functional monomer, and ethylene glycol dimethacrylate was the crosslinking monomer, using a solution of polystyrene in tetrahydrofuran as a molecular crowding agent with isooctane as a coporogen. In addition, it was found that the ratio of the macromolecule agent, the amount of templates and crosslinking degree, and the composition of the mobile phase greatly affected the retention of the template and performance of molecular recognition. The imprinting factor of the resulting MIP monolith obtained was up to 9.67. The resulting MIP can be used to purify EGCG from crude tea polyphenol efficiently with mean recoveries of 87.42 %.

     

Carprofen-imprinted monolith prepared by reversible addition–fragmentation chain transfer polymerization in room temperature ionic liquids

To obtain fast separation, ionic liquids were used as porogens first in combination with reversible addition–fragmentation chain transfer (RAFT) polymerization to prepare a new type of molecularly imprinted polymer (MIP) monolith. The imprinted monolithic column was synthesized using a mixture of carprofen (template), 4-vinylpyridine, ethylene glycol dimethacrylate, [BMIM]BF₄, and chain transfer agent (CTA). Some polymerization factors, such as template-monomer molar ratio, the degree of crosslinking, the composition of the porogen, and the content of CTA, on the column efficiency and imprinting effect of the resulting MIP monolith were systematically investigated. Affinity screening of structurally similar compounds with the template can be achieved in 200 s on the MIP monolith due to high column efficiency (up to 12,070 plates/m) and good column permeability. Recognition mechanism of the imprinted monolith was also investigated.     

Molecularly imprinted polymers as a tool for separation in CEC

Molecularly imprinted polymers (MIPs) are synthesized in the presence of a template which results in the formation of specific recognition cavities complementary to the template in shape and chemical functionality. One of the most successful application areas of MIPs is chromatographic sorbents, which are tailor-made synthetic polymers for a given analyte. However, low efficiency of MIP columns is often observed because of slow kinetics of the template. CEC-based MIPs are thought to improve efficiency of MIP-based separation due to the enhanced flow dynamics of CEC. Another attractive feature is the miniaturized format of CEC, so that fewer templates or monomers for the molecular imprinting are consumed, a characteristic desired for 'green chemistry'. The small dimensions of a capillary demand the development of novel polymer formats that can be applied to a miniaturized system. This review discusses the various formats, i.e., the micro- or nanoparticle, the coating and the monolith, for application in CEC as well as the use in MIP syntheses and characteristics.     

A thermosensitive monolithic column as an artificial antibody for the on-line selective separation of the protein

The main objective of this study was to develop a new methodology for the preparation of a protein (antigen) that is a molecularly imprinted polymer (MIP, an artificial antibody) modified onto the surface of a silica skeleton in which the resulting stationary phase is thermosensitive. The silica monolithic skeleton with vinyl groups was synthesized in a stainless-steel column by using a mild one-step sol-gel process with two types of precursor: methyltrimethoxysilane (MTMS) and γ-methacryloxypropyltrimethoxysilane (γ-MAPS). Subsequently, three types of the thermosensitive protein MIP were anchored onto the surface of the silica skeleton to prepare the MIP monoliths, which were systematically investigated for back pressure and separation ability at different temperatures to establish good imprinting conditions. Under the optimized imprinting conditions, the chromatographic behavior of the thermosensitive MIP monolith exhibited strong retention ability for the lysozyme template (target antigen) in relation to the nonimprinting monolith (NIP monolith). The imprinting factor (IF) for lysozyme reached 3.48 at 20 °C. Moreover, this new type of artificial antibody displayed favorable binding characteristics for lysozyme over competitive proteins and was further evaluated to selectively separate lysozyme in a real sample by using an on-line method. The run-to-run and column-to-column repeatability measurements of the thermosensitive MIP monoliths were also satisfactory.     

The development of a semiautomated procedure for the synthesis and screening of a large group of molecularly imprinted polymers

A method for synthesis and evaluation of molecularly imprinted polymers (MIPs) on a semiautomated miniature scale is reported. This technique combines molecular imprinting with the combinatorial chemistry approach, allowing rapid screening and optimizations of libraries of MIPs. The polymers were prepared and evaluated in situ by rebinding utilizing powder dispensing and liquid handling systems. MIPs were prepared by a combinatorial approach using methacrylic acid (MAA), 4-vinylpyridine (4-VP), acrylamide, and styrene as functional monomers, and acetonitrile and toluene as porogenic solvents. A drug substance having aromatic, hydroxyl, -O-CONH2 functional groups was selected as the template molecule for this study. The MIP library results demonstrated that the polymer prepared with MAA as functional monomer shows the strongest binding affinity, and therefore, is preferred for the preparation of this particular template molecule. Due to the low consumption of reagents, and more importantly, the demonstrated ability of this method to effectively identify optimal imprinting conditions, this small-scale combinatorial protocol is well suited for fast and efficient screening and optimizations of MIPs.     

Macroporous molecularly imprinted polymer/cryogel composite systems for the removal of endocrine disrupting trace contaminants

A new concept for the preparation of selective sorbents with high flow path properties is presented by embedding molecularly imprinted polymers (MIPs) into various macroporous gels (MGs). A MIP was first synthetized with 17beta-estradiol (E2) as template for the selective adsorption of this endocrine disrupter. The composite macroporous gel/MIP (MG/MIP) monoliths were then prepared at subzero temperatures. Complete recovery of E2 from a 2 microg/L aqueous solution was achieved using the polyvinyl alcohol (PVA) MG/MIP monoliths whereas only 49-74% was removed with non-imprinted polymers (when no template was used). The PVA MG/MIP monolith columns were operated at almost 10 times higher flow rate (50 mL/min) compared to the MIP columns with operation flow rate of 1-5 mL/min. The possibility for processing the particulate containing wastewater effluents at high flow rates with selectivity on E2 removal, as well as the easy preparation of the monoliths, make the macroporous MG/MIP systems attractive and robust sorbents for the clean up of water from endocrine disrupting trace contaminants.