Binding cellulose and chitosan via click chemistry: Synthesis,characterization, and formation of some hollow tubes

A novel cellulose‐click‐chitosan polymer was prepared successfully in three steps: (1) propargyl cellulose with degrees of substitution (DS) from 0.25 to 1.24 was synthesized by etherification of bamboo Phyllostachys bambusoide cellulose with propargyl chloride in DMA/LiCl in the presence of NaH. The regioselectivity of propargylation on anhydrous glucose unit determined by GC‐MS was in the order of 2 >> 6 > 3; (2) the functional azide groups were introduced onto the chitosan chains by reacting chitosan with 4‐azidobenzoic acid in [Amim]Cl/DMF and the DS ranged from 0.02 to 0.46; (3) thus, the cellulose‐click‐chitosan polymer was obtained via click reaction, that is, the Cu(I)‐catalyzed Huisgen 1,3‐dipolar cycloaddition reaction, between the terminal alkyne groups of cellulose and the azide groups on the chitosan backbone at room temperature. The successful binding of cellulose and chitosan was confirmed and characterized by FTIR and CP/MAS ¹³C NMR spectroscopy. TGA analyses indicated that the cellulose‐click‐chitosan polymer had a higher thermal stability than that of cellulose and chitosan as well as cellulose–chitosan complex. More interestingly, some hollow tubes with near millimeter length were also observed by SEM. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Structural and thermal characterization of sugarcane bagasse cellulose succinates prepared in ionic liquid

The chemical modification of SCB cellulose with succinic anhydride using 1-butyl-3-methylimidazolium chloride ionic liquid/DMSO system as reaction medium was studied. The parameters including the molar ratio of succinic anhydride/anhydroglucose units in cellulose from 1:1 to 12:1, reaction time 5-120 min, and reaction temperature 85-105 °C were investigated. The results showed that the degree substitution of succinylated cellulosic preparations ranged from 0.037 to 0.53. It was found that the treatment of the native cellulose in the ionic liquid/DMSO system under the conditions given significantly degraded the cellulose and completely destroyed the cellulose crystals. FT-IR and solid-state CP/MAS ¹³C NMR spectra produced evidence for succinoylation reaction and the results showed that succinoylation occurred at positions C-6, C-2 and C-3. The thermal stability of the succinylated cellulose decreased upon chemical modification.     

Benzylation of cellulose in the solvent dimethylsulfoxide/tetrabutylammonium fluoride trihydrate

The cellulose solvent dimethylsulfoxide/tetrabutylammonium fluoride trihydrate (TBAF·3 H₂O) was studied as reaction medium for the synthesis of benzyl cellulose (BC) by treating the dissolved polymer with benzyl chloride in the presence of solid NaOH or aqueous NaOH solution. BC samples with degree of substitution (DS) between 0.40 and 2.85 were accessible applying different molar ratios. The studies show that both the TBAF·3 H₂O concentration and the molar ratio of the reagents to repeating unit influence the DS. The solubility of the BC synthesized in a different way, however, of comparable DS is different. Structural analyses were carried out by means of FTIR-, ¹H- and ¹³C NMR spectroscopy. SEC measurements revealed polymer aggregation in samples of low DS synthesized in a solvent containing 9.0% TBAF·3 H₂O. At higher concentration of TBAF·3 H₂O in the solvent, the BC samples obtained do not form aggregates. BC of high DS is crystalline and shows thermotropic liquid crystalline behavior as analyzed by means of DSC. Melting point and degradation temperature are not related to the DS.     

Preparation and characterization of hybrid cationic hydroxyethyl cellulose/sodium alginate polyelectrolyte antimicrobial films

This study aimed to develop polyelectrolyte‐structured antimicrobial food packaging materials that do not contain any antimicrobial agents. Cationic hydroxyethyl cellulose was synthesized and characterized by Fourier‐transform infrared, ¹H NMR, and ¹³C NMR spectroscopy. Its nitrogen content was determined by Kjeldahl method. Polyelectrolyte‐structured antimicrobial food packaging materials were prepared using hydroxyethyl cellulose, cationic hydroxyethyl cellulose, and sodium alginate. Antimicrobial activity of materials was defined by inhibition zone method (disc diffusion method). Thermal stability of samples was evaluated by thermal gravimetric analysis and differential scanning calorimetry. Surface morphology of samples was investigated by SEM. The obtained results prove that produced food packaging materials have good thermal and antimicrobial properties, and they can be used as food packaging material in many industries.     

Synthesis and characterization of novel amino cellulose esters

The homogeneous conversion of cellulose dissolved in N-methyl-2-pyrrolidone/LiCl and 1-N-butyl-3-methylimidazolium chloride with N-methyl-2-pyrrolidone, ε-caprolactam, N-methyl-ε-caprolactam, and N-methyl-2-piperidone in the presence of p-toluenesulphonic acid chloride was studied. Depending on the reaction conditions, novel cellulose esters with degree of substitution (DS) values ranging from 0.12 to 1.17 could be prepared. The structure of the amino group containing cellulose esters was elucidated by elemental analysis, FTIR- and NMR spectroscopy. NMR spectroscopy revealed an almost complete esterification of position 6 of the anhydroglucose unit at DS of 1. The conversion can be conducted between room temperature and 40 °C, while side-reactions became predominant at 60 °C. Starting with DS of 0.24, the samples were soluble both in water and dimethyl sulphoxide. The derivatives described are capable of forming polyelectrolyte complexes. The samples were stable at room temperature in aqueous solution at pH 2 and 7. Lower viscosities were found for samples with higher DS in aqueous solution at comparable molar mass.     

Two-step preparation and thermal characterization of cationic 2-hydroxypropyltrimethylammonium chloride hemicellulose polymers from sugarcane bagasse

Cationic sugarcane bagasse hemicellulose derivatives with a relatively low degree of substitution (0.01-0.54) containing quaternary ammonium groups were prepared by etherification with 3-chloro-2-hydroxypropyltrimethylammonium chloride or preferably with 2,3-epoxypropyltrimethylammonium chloride using sodium hydroxide as a catalyst in aqueous solution. The extent of etherification was measured by yield percentage and degree of substitution (DS). The DS values of the products could be controlled by adjusting the molar ratio of etherifying agent to anhydroxylose units in hemicelluloses and the molar ratio of sodium hydroxide to etherifying reagent. In comparison, the etherified hemicellulose preparations were characterized by both degradative methods such as thermal analysis, and non-degradative techniques such as gel permeation chromatography (GPC), Fourier transform infrared (FT-IR), and ¹³C nuclear magnetic resonance (NMR) spectroscopy. It was found that a significant degradation of the hemicellulose polymers occurred during etherification under the alkaline conditions used. The thermal stability of the etherified hemicelluloses was lower than that of the unmodified hemicellulose polymers.     

Study on the morphology, crystalline structure and thermal properties of yellow ginger starch acetates with different degrees of substitution

Yellow ginger starch acetates with different degrees of substitution (DS) were prepared by reacting native starch with glacial acetic acid/acetic anhydride using sulfuric acid as catalyst. X-ray diffraction (XRD) of acetylated starch revealed that the crystal structure of native starch was disappeared and new crystalline regions were formed. Their formation was confirmed by the presence of the carbonyl signal around 1750 cm⁻¹, as well as the reduced hydroxyl groups, in the Fourier transform infrared spectroscopy (FT-IR). The scanning electron microscopy (SEM) suggested most of the starch granules disintegrated with many visible fragments along with the increasing DS. The thermal behavior of the native starch and starch acetate were investigated using thermogravimetric analysis (TGA) and differential thermal analysis (DTA), it was observed that the thermal stability of acetylated starch depends on the degree of substitution. Thermal stability of high DS acetylated starch is much better than that of the original starch when DS reached to 2.67.     

Syntheses and characterizations of allyl cellulose and glycidyl cellulose

Allyl cellulose was synthesized by reacting cellulose with allyl bromide in homogeneous LiCl/DMAc solution containing NaOH powder. The degree of substitution (DS) per anhydroglucose (AHG) unit was determined by titrating the allyl cellulose with bromine in chloroform solution, and an allyl DS of 2.80 was found. Glycidyl cellulose was then prepared by reacting this allyl cellulose with peracetic acid in methylene chloride at ambient temperature for 6 days. The measured reaction rate constant was 1.33 × 10^?3 min^?1. The glycidyl cellulose thus obtained with a glycidyl DS of 2.58 was determined by titrating the product with perchloric acid in conjunction with tetrabutylammonium iodide. The 2.58 of glycidyl DS was also confirmed by ¹H-NMR integration. Both allyl cellulose and glycidyl cellulose were analyzed and characterized with FTIR, ¹H-NMR, ¹³C-NMR, TGA, and GPC. During epoxidation of allyl cellulose, possible side reaction leading to ester formation was evidenced from the continuous increase of v_{C? O} at 1735 cm^?1 in FTIR analyses. In addition, a bimodal distribution and a decreased molecular weight for glycidyl cellulose were found from GPC data, which might suggest a possible chain scission at the cellulosic ether linkage. © 1992 John Wiley & Sons, Inc.     

Thermal characterization of benzylcellulose derivatives prepared from bleached pinus kraft pulp

The thermal characterization (DSC and TG) of benzylcellulose derivatives prepared from the benzylation of bleached Pinus Kraft pulp is described in this paper. The objective of this study was to examine the changes in glass transition temperature (T _g) and the thermal stability of the benzylated product as a function of the benzylation extent (degree of substitution). The DSC analysis showed that the benzylcelluloses can display glass transition temperature at two different regions and that thermal stability is slightly higher than that of the parent cellulose. This revised version was published online in August 2006 with corrections to the Cover Date.     

Efficient Homogeneous Chemical Modification of Bacterial Cellulose in the Ionic Liquid 1‐N‐Butyl‐3‐methylimidazolium Chloride

Summary: Bacterial cellulose (BC), a unique type of cellulose, with high degree of polymerization of 6 500 could be dissolved easily in the ionic liquid 1‐N‐butyl‐3‐methylimidazolium chloride. For the first time, well‐soluble BC acetates and carbanilates of high degree of substitution (up to a complete modification of all hydroxyl groups) were accessible under homogeneous and mild reaction conditions. Characterization of the new BC derivatives by NMR and FTIR spectroscopy shows an unexpected distribution of the acetyl moieties in the order O‐6 > O‐3 > O‐2.

¹³C NMR spectrum (DMSO‐d₆) of a cellulose acetate with a DS of 2.25 synthesized in 1‐N‐butyl‐3‐methylimidazolium chloride.     

Preparation and characterization of cellulose β-ketoesters prepared by homogeneous reaction with alkylketene dimers: comparison with cellulose/fatty acid esters

Cellulose was dissolved in lithium chloride/1,3-dimethyl-2-imidazolidinone (LiCl/DMI), and reacted with alkylketene dimers (AKDs) under non-aqueous and homogeneous conditions to prepare cellulose/AKD β-ketoesters with high degrees of substitution (DS). Six AKDs synthesized from octanoic, decanoic, dodecanoic, tetradecanoic, hexadecanoic and octadecanoic acids via their fatty acid chlorides were used in this study. The cellulose/AKD β-ketoesters obtained were gummy solid at room temperature, and had DS values ranging from 1.9 to 2.9. Cellulose/fatty acid esters with DS 2.5–2.9 were also prepared as references. ¹³C-NMR spectra of the cellulose/AKD β-ketoesters showed that cellulose carbons and substituent carbons close to cellulose chains were restricted in motion and behaved like solid in solutions. In contrast, the cellulose/fatty acid esters did not demonstrate such anomalous ¹³C-NMR spectra. The unique ¹³C-NMR patterns are characteristic for the cellulose/AKD β-ketoesters, which have long and branched alkyl substituents in each anhydroglucose unit. Size-exclusion chromatography furnished with multi-angle laser light scattering (SEC-MALLS) revealed, on the other hand, that all cellulose/AKD β-ketoesters and cellulose/fatty acid esters prepared had flexible or random-coil conformations in tetrahydrofuran (THF). There were no clear differences in conformation or stiffness of cellulose chains between cellulose/AKD β-ketoesters and cellulose/fatty acid esters.     

Catalytic properties of the Cr-HMS materials in the benzylation of benzene with benzyl chloride

A series of chromium-containing mesoporous silicas with different Cr contents were prepared and characterized with chemical analysis, N₂ adsorption measurements (BET equation and BJH theory), X-ray diffraction, diffuse reflectance UV-visible and H₂-temperature programmed reduction techniques. Excellent results in benzylation of benzene and substituted benzenes employing benzyl chloride as the alkylating agent were obtained. The mesoporous chromium-containing materials showed both high activity and high selectivity for benzylation of benzene. The activity of these catalysts for the benzylation of different aromatic compounds is in the following order: benzene > toluene > p-xylene > anisole. Kinetics of the benzene benzylation over these catalysts has also been investigated.     

Substitution Patterns of Cellulose Ethers - Influence of the Synthetic Pathway

Commercial cellulose ethers are usually prepared under heterogeneous reaction conditions. In contrast, this contribution also describes the derivatization under homogeneous conditions in N-methylmorpholine-N-oxide monohydrate (NMMNO*H₂O) and under heterogeneous conditions after converting native cellulose to amorphous cellulose. Amorphous cellulose is prepared by dissolving cellulose in NMMNO*H₂O followed by precipitation in different media. The degree of order and the porosity of the regenerated cellulose is significantly influenced by the content of water in the precipitating agent. The differences are described by measurements using wide angle X-ray scattering, solid-state ¹³C-NMR, mercury porosimetry, and water/liquid retention values. Three synthetic pathways (heterogeneous, heterogeneous with amorphous cellulose and homogeneous) are compared regarding the structure-property relationship of the cellulose ethers formed. Carboxymethylation, hydroxyethylation, hydroxypropylation and sulfoethylation are considered in detail. The choice of synthetic pathway has a significant influence on the degree of substitution (DS), the distribution of substituents on the level of the anhydroglucose unit (AGU), solubility behavior, and the viscosity of aqueous solutions. In general an increasing solubility and an increasing viscosity are observed from heterogeneous to heterogeneous with amorphous cellulose to homogeneous reaction conditions. There is a remarkable difference between the heterogeneously produced cellulose ethers with a DS distribution C2 ≥ C6 > C3 and the strictly homogeneous etherification in NMMNO*H₂O/organic solvent systems with a DS distribution of C3 > C2 ≫ C6. This high regioselectivity at the secondary OH-groups of the AGU may be caused by the strong solvation behavior of NMMNO*H₂O and thereby a protecting function at the C6-OH-group.     

Highly selective synthesis of diphenyl methane via liquid phase benzylation of benzene over cobalt doped zinc nanoferrite catalysts at mild conditions

Liquid phase benzylation of benzene with benzyl chloride was investigated over different compositions of cobalt zinc ferrite (Co_xZn_1-xFe₂O_4, x-0.0, 0.25, 0.5, 0.75, 1.0) nano composites, synthesized by sol–gel method. The un-substituted cobalt ferrite catalyst exhibited excellent activity among the series effecting complete conversion of benzyl chloride in 60?min at 90?°C with 100% selectivity for diphenyl methane. The effect of various reaction parameters on the reaction was studied. Higher benzylation activity of cobalt ferrite nanocomposite is attributed to the presence of higher quantities of moderately acidic sites and a good correlation was observed between surface acidity and benzylation activity of catalysts. The catalysts are reusable without any significant structural change as indicated by X-ray Diffraction (XRD) and Atomic Absorption Spectrophotometer (AAS).     

Efficient synthesis of 1-R1-2-R-4,5-di(furan-2-yl)-1H-imidazoles and their luminescence properties

In this study, a series of 1-R₁-2-R-4,5-di(furan-2-yl)-1H-imidazole derivatives were synthesized in better yield 59.0%∼89.8% by the treatment of purified imidazole compounds with benzyl chloride or allyl chloride in the presence of sodium hydride, and were characterized by FT–IR, HRMS, ¹H NMR and ¹³C NMR spectroscopy. Furthermore, the luminescence properties of the synthesized products were investigated. It was found that N-substituted groups of imidazole have little influence on the absorption bands in a 0.1 N H₂SO₄ aqueous solution containing 0.5 mL of dissolved CH₃OH. However, the emission of some compounds in solution was sensitive to the polarity of the solvents.     

Aqueous single step synthesis and structural characterization of allylated,propargylated, and benzylated 3-substituted 3-aminooxindoles

Efficient zinc-mediated allylation, propargylation, and benzylation of isatin-derived imines were undertaken for the synthesis of 3-substituted 3-aminooxindoles with ≈80% yield. Such alternative approach has efficiently avoided the use of catalysts, severe reaction conditions, multistep procedures, and reaction additives. For exploring and materializing the synthetic utility, different allyl, propargyl, and benzyl bromides were used for generalizing the synthetic route. The structure of the synthesized compounds was established and confirmed by ¹H NMR, ¹³C NMR, FTIR, and mass spectroscopic techniques.     

Synthesis of cellulose benzoates under homogeneous conditions in an ionic liquid

The ionic liquid 1-allyl-3-methylimidazolium chloride (AmimCl) as a reaction medium was studied for the synthesis of cellulose benzoates by homogeneous acylation of dissolved cellulose with benzoyl chlorides in the absence of any catalysts. Cellulose benzoates with a degree of substitution (DS) in the range from about 1 to 3.0 were accessible under mild conditions. The DS of cellulose derivatives increased with the increase of the molar ratio of benzoyl chloride/anhydroglucose unit (AGU) in cellulose, reaction time, and reaction temperature. Benzoylation of cellulose with some 4-substituted benzoyl chlorides including 4-toluoyl chloride, 4-chlorobenzoyl chloride and 4-nitrobenzoyl chloride was also readily carried out under mild conditions. Furthermore, regioselectively substituted mixed cellulose esters were synthesized in this work. All products were characterized by means of FT-IR, ¹H-NMR, and ¹³C-NMR spectroscopy. In addition, at the end of benzoylation of cellulose, the ionic liquid AmimCl was easily recycled. When the recycled AmimCl was used as the reaction media, the cellulose benzoate with a similar DS was obtained under comparable reaction conditions.     

Highly active and reusable catalyst from Fe-Mg-hydrotalcite anionic clay for Friedel-Crafts type benzylation reactions

Fe-Mg-hydrotalcite (Mg/Fe = 3) anionic clay with or without calcination (at 200–800‡C) has been used for the benzylation of toluene and other aromatic compounds by benzyl chloride. Hydrotalcite before and after its calcination was characterized for surface area, crystalline phases and basicity. Both the hydrotalcite, particularly after its use in the benzylation reaction, and the catalyst derived from it by its calcination at 200–800‡C show high catalytic activity for the benzylation of toluene and other aromatic compounds. The catalytically active species present in the catalyst in its most active form are the chlorides and oxides of iron on the catalyst surface.     

Synthesis of a side chain liquid crystalline polymer containing the cholesteryl moiety via ROP and “click” chemistry

Propargyl monocholesterylsuccinate (ChPS) was prepared through the esterification of monocholesterylsuccinate with propargyl alcohol, and poly(3-azidomethyl-3-methyloxetane) (PAMMO) was synthesized via cationic polymerization, using boron trifluoride etherate as catalyst and benzyl alcohol as initiator in methylene chloride. Through the copper-catalyzed “click” reaction between the azide group on PAMMO and the alkyne group on ChPS, a side chain liquid crystalline polymer containing the cholesteryl moiety (Ch-SCLCP) was obtained. The “click” reaction was confirmed by IR, ¹H NMR, ¹³C NMR, and GPC studies. The resulting polymer showed thermotropic mesophase as judged by polarized optical microscopy (POM) and differential scanning calorimetry (DSC).     

Preparation of POSS-based organic–inorganic hybrid mesoporous materials networks through Schiff base chemistry

The synthesis of novel POSS-based organic–inorganic hybrid mesoporous materials networks functionalized with amine groups through Schiff base chemistry is reported. The material shows uniform mesoporous size. Nitrogen sorption analyses give high specific surface areas of 641–1103 m² g⁻¹ with pore volumes of 0.47–0.53 mL g⁻¹. The combined results of FTIR, solid ¹³C NMR and ²⁹Si NMR show that the POSS building blocks are successfully weaved in the porous structure without obvious alteration of the POSS structural characteristics. The hybrid materials show excellent thermal stability.